ARM: display5: Remove UART initialization code after DM/DTS conversion (non-console)
This UART is not used in U-Boot, so there is no need to initialize it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
diff --git a/board/liebherr/display5/common.c b/board/liebherr/display5/common.c
index d2d174b..5e71407 100644
--- a/board/liebherr/display5/common.c
+++ b/board/liebherr/display5/common.c
@@ -8,14 +8,6 @@
#include <asm/arch/mx6-pins.h>
#include "common.h"
-iomux_v3_cfg_t const uart_pads[] = {
- /* UART4 */
- MX6_PAD_CSI0_DAT12__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT13__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT16__UART4_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
- MX6_PAD_CSI0_DAT17__UART4_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
iomux_v3_cfg_t const uart_console_pads[] = {
/* UART5 */
MX6_PAD_CSI0_DAT14__UART5_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
@@ -29,11 +21,6 @@
SETUP_IOMUX_PADS(uart_console_pads);
}
-void displ5_set_iomux_uart(void)
-{
- SETUP_IOMUX_PADS(uart_pads);
-}
-
iomux_v3_cfg_t const misc_pads_spl[] = {
/* Emergency recovery pin */
MX6_PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL),
diff --git a/board/liebherr/display5/common.h b/board/liebherr/display5/common.h
index 2bbd934..4eb70dc 100644
--- a/board/liebherr/display5/common.h
+++ b/board/liebherr/display5/common.h
@@ -32,7 +32,6 @@
PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
void displ5_set_iomux_uart_spl(void);
-void displ5_set_iomux_uart(void);
void displ5_set_iomux_ecspi_spl(void);
void displ5_set_iomux_usdhc_spl(void);
void displ5_set_iomux_misc_spl(void);
diff --git a/board/liebherr/display5/display5.c b/board/liebherr/display5/display5.c
index 541e3e9..5713401 100644
--- a/board/liebherr/display5/display5.c
+++ b/board/liebherr/display5/display5.c
@@ -174,8 +174,6 @@
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
- /* Setup iomux for non console UARTS */
- displ5_set_iomux_uart();
/* Setup misc (application specific) stuff */
SETUP_IOMUX_PADS(misc_pads);