ARM: LogicPD: omap3logic: Remove Torpedo/SOM-LV autodection
With there now being four device tree files, and 4 separate
defconfig files, the code necessary to determine which board is
being used is no longer necessary as the corresponding pin-muxing
and board names are determined by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
diff --git a/board/logicpd/omap3som/README b/board/logicpd/omap3som/README
index b77b3d6..5aaf58f 100644
--- a/board/logicpd/omap3som/README
+++ b/board/logicpd/omap3som/README
@@ -1,21 +1,15 @@
Summary
=======
-The source for omap3som encompases the DM3730 SOM-LV and DM3730 Torpedo platforms.
+The source for omap3logic.c encompases the OMAP35 and DM3730 SOM-LV and DM3730 Torpedo platforms, but there are device trees custom taylored to each board.
-By default, the Torpedo Device Tree is integrated into U-Boot,but the MMC controller, GPIO and I2C controllers are the same, so for the purposes of loading U-Boot, it should be sufficient. However this will display the Model as "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit" upon boot.
-
-The actual board remains autodetected and the Board will read "DM37xx SOM LV" when used on the DM37 SOM-LV. The device tree loaded with Linux is also correct.
-
-Integrating the SOM-LV Device Tree into U-Boot
-==============================================
-
-This step is optional, but should you want to change the default to the SOM-LV, locate the configs/omap3_logic_defconfig file and make the following change.
-
- CONFIG_DEFAULT_DEVICE_TREE="logicpd-som-lv-37xx-devkit"
+omap3_logic_defconfig = DM37 Torpedo / Torpedo + Wireless
+omap35_logic_defconfig = OMAP35 Torpedo
+omap3_logic_somlv_defconfig = DM37 SOM-LV
+omap35_logic_somlv_defconfig = OMAP35 SOM-LV
- make distclean
- make omap3_logic_defconfig
+The device tree included with each of the defconfig files will also direct the board as to which dtb file to load when loading the kernel, so it is not
+recomended to mix and match the defconfig files.
Falcon Mode: FAT SD cards
=========================
diff --git a/board/logicpd/omap3som/omap3logic.c b/board/logicpd/omap3som/omap3logic.c
index 48d8869..4507b1e 100644
--- a/board/logicpd/omap3som/omap3logic.c
+++ b/board/logicpd/omap3som/omap3logic.c
@@ -70,40 +70,6 @@
#endif
-/*
- * two dimensional array of strucures containining board name and Linux
- * machine IDs; row it selected based on CPU column is slected based
- * on hsusb0_data5 pin having a pulldown resistor
- */
-static struct board_id {
- char *name;
- int machine_id;
- char *fdtfile;
-} boards[2][2] = {
- {
- {
- .name = "OMAP35xx SOM LV",
- .machine_id = MACH_TYPE_OMAP3530_LV_SOM,
- .fdtfile = "logicpd-som-lv-35xx-devkit.dtb",
- },
- {
- .name = "OMAP35xx Torpedo",
- .machine_id = MACH_TYPE_OMAP3_TORPEDO,
- .fdtfile = "logicpd-torpedo-35xx-devkit.dtb",
- },
- },
- {
- {
- .name = "DM37xx SOM LV",
- .fdtfile = "logicpd-som-lv-37xx-devkit.dtb",
- },
- {
- .name = "DM37xx Torpedo",
- .fdtfile = "logicpd-torpedo-37xx-devkit.dtb",
- },
- },
-};
-
#ifdef CONFIG_SPL_OS_BOOT
int spl_start_uboot(void)
{
@@ -226,7 +192,6 @@
#endif /* CONFIG_USB_EHCI_HCD */
-
/*
* Routine: misc_init_r
* Description: Configure board specific parts
@@ -244,11 +209,6 @@
}
/*
- * BOARD_ID_GPIO - GPIO of pin with optional pulldown resistor on SOM LV
- */
-#define BOARD_ID_GPIO 189 /* hsusb0_data5 pin */
-
-/*
* Routine: board_init
* Description: Early hardware init.
*/
@@ -275,54 +235,6 @@
int board_late_init(void)
{
- struct board_id *board;
- unsigned int val;
-
- /*
- * To identify between a SOM LV and Torpedo module,
- * a pulldown resistor is on hsusb0_data5 for the SOM LV module.
- * Drive the pin (and let it soak), then read it back.
- * If the pin is still high its a Torpedo. If low its a SOM LV
- */
-
- /* Mux hsusb0_data5 as a GPIO */
- MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M4));
-
- if (gpio_request(BOARD_ID_GPIO, "husb0_data5.gpio_189") == 0) {
-
- /*
- * Drive BOARD_ID_GPIO - the pulldown resistor on the SOM LV
- * will drain the voltage.
- */
- gpio_direction_output(BOARD_ID_GPIO, 0);
- gpio_set_value(BOARD_ID_GPIO, 1);
-
- /* Let it soak for a bit */
- sdelay(0x100);
-
- /*
- * Read state of BOARD_ID_GPIO as an input and if its set.
- * If so the board is a Torpedo
- */
- gpio_direction_input(BOARD_ID_GPIO);
- val = gpio_get_value(BOARD_ID_GPIO);
- gpio_free(BOARD_ID_GPIO);
-
- board = &boards[!!(get_cpu_family() == CPU_OMAP36XX)][!!val];
- printf("Board: %s\n", board->name);
-
- /* Set the machine_id passed to Linux */
- if (board->machine_id)
- gd->bd->bi_arch_number = board->machine_id;
-
- /* If the user has not set fdtimage, set the default */
- if (!env_get("fdtimage"))
- env_set("fdtimage", board->fdtfile);
- }
-
- /* restore hsusb0_data5 pin as hsusb0_data5 */
- MUX_VAL(CP(HSUSB0_DATA5), (IEN | PTD | DIS | M0));
-
#ifdef CONFIG_CMD_NAND_LOCK_UNLOCK
unlock_nand();
#endif
@@ -356,5 +268,3 @@
return smc911x_initialize(0, CONFIG_SMC911X_BASE);
}
#endif
-
-