arm,davinci: update for enbw_cmc board
- change gpio pin settings:
- gpio pin 6[13] (PLC reset) default value low
- gpio pin 6[0] (TPM reset) default value low
- 4 new GPIO pins
pin i/o name
- 3[9] input Board Type
- 2[7] input HW-ID0
- 2[6] input HW-ID1
- 2[3] input HW-ID2
- read board type and hw id from gpio pins on the enbw_cmc board,
and use board type for setting up different gpio pin settings.
- do not pass "davinci_mmc.use_dma=0" to linux, as MMC now
works with DMA.
- update logbuf support:
store post word in RTC scratch register
- add support for configuring KSZ8864RMN switch through
a config file on u-boot startup. For more infos see:
doc/README.switch_config
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <tom.rini@gmail.com>
Cc: Christian Riesch <christian.riesch@omicron.at>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
diff --git a/board/enbw/enbw_cmc/enbw_cmc.c b/board/enbw/enbw_cmc/enbw_cmc.c
index 6c0d931..0874e9c 100644
--- a/board/enbw/enbw_cmc/enbw_cmc.c
+++ b/board/enbw/enbw_cmc/enbw_cmc.c
@@ -35,6 +35,8 @@
#include <mmc.h>
#include <net.h>
#include <netdev.h>
+#include <spi.h>
+#include <linux/ctype.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <asm/arch/da850_lowlevel.h>
@@ -86,16 +88,22 @@
{ pinmux(5), 1, 0 },
{ pinmux(5), 1, 3 },
{ pinmux(5), 1, 7 },
- { pinmux(6), 1, 0 },
- { pinmux(6), 1, 1 },
+ { pinmux(5), 1, 5 },
+ { pinmux(5), 1, 4 },
+ { pinmux(5), 1, 3 },
+ { pinmux(5), 1, 2 },
+ { pinmux(5), 1, 1 },
+ { pinmux(5), 1, 0 },
+ { pinmux(6), 8, 0 },
+ { pinmux(6), 8, 1 },
{ pinmux(6), 8, 2 },
{ pinmux(6), 8, 3 },
- { pinmux(6), 1, 4 },
+ { pinmux(6), 8, 4 },
{ pinmux(6), 8, 5 },
{ pinmux(6), 1, 7 },
{ pinmux(7), 8, 2 },
{ pinmux(7), 1, 3 },
- { pinmux(7), 1, 6 },
+ { pinmux(7), 8, 6 },
{ pinmux(7), 1, 7 },
{ pinmux(13), 8, 2 },
{ pinmux(13), 8, 3 },
@@ -163,24 +171,37 @@
unsigned char value;
};
-static const struct gpio_config enbw_gpio_config[] = {
+static const struct gpio_config enbw_gpio_config_hut[] = {
+ { "RS485 enable", 8, 11, 1, 0 },
+ { "RS485 iso", 8, 10, 1, 1 },
+ { "W2HUT RS485 Rx ena", 8, 9, 1, 0 },
+ { "W2HUT RS485 iso", 8, 8, 1, 1 },
+};
+
+static const struct gpio_config enbw_gpio_config_w[] = {
{ "RS485 enable", 8, 11, 1, 0 },
{ "RS485 iso", 8, 10, 1, 0 },
{ "W2HUT RS485 Rx ena", 8, 9, 1, 0 },
{ "W2HUT RS485 iso", 8, 8, 1, 0 },
+};
+
+static const struct gpio_config enbw_gpio_config[] = {
{ "LAN reset", 7, 15, 1, 1 },
{ "ena 11V PLC", 7, 14, 1, 0 },
{ "ena 1.5V PLC", 7, 13, 1, 0 },
{ "disable VBUS", 7, 12, 1, 1 },
- { "PLC reset", 6, 13, 1, 1 },
+ { "PLC reset", 6, 13, 1, 0 },
{ "LCM RS", 6, 12, 1, 0 },
{ "LCM R/W", 6, 11, 1, 0 },
{ "PLC pairing", 6, 10, 1, 1 },
{ "PLC MDIO CLK", 6, 9, 1, 0 },
{ "HK218", 6, 8, 1, 0 },
{ "HK218 Rx", 6, 1, 1, 1 },
- { "TPM reset", 6, 0, 1, 1 },
- { "LCM E", 2, 2, 1, 1 },
+ { "TPM reset", 6, 0, 1, 0 },
+ { "Board-Type", 3, 9, 0, 0 },
+ { "HW-ID0", 2, 7, 0, 0 },
+ { "HW-ID1", 2, 6, 0, 0 },
+ { "HW-ID2", 2, 3, 0, 0 },
{ "PV-IF RxD ena", 0, 15, 1, 1 },
{ "LED1", 1, 15, 1, 1 },
{ "LED2", 0, 1, 1, 1 },
@@ -229,34 +250,57 @@
}
}
-int board_init(void)
+static int enbw_cmc_init_gpio(const struct gpio_config *conf, int sz)
{
int i, ret;
-#ifndef CONFIG_USE_IRQ
- irq_init();
-#endif
- /* address of boot parameters, not used as booting with DTT */
- gd->bd->bi_boot_params = 0;
-
- for (i = 0; i < ARRAY_SIZE(enbw_gpio_config); i++) {
- int gpio = enbw_gpio_config[i].bank * 16 +
- enbw_gpio_config[i].gpio;
+ for (i = 0; i < sz; i++) {
+ int gpio = conf[i].bank * 16 +
+ conf[i].gpio;
- ret = gpio_request(gpio, enbw_gpio_config[i].name);
+ ret = gpio_request(gpio, conf[i].name);
if (ret) {
printf("%s: Could not get %s gpio\n", __func__,
- enbw_gpio_config[i].name);
- return -1;
+ conf[i].name);
+ return ret;
}
- if (enbw_gpio_config[i].out)
+ if (conf[i].out)
gpio_direction_output(gpio,
- enbw_gpio_config[i].value);
+ conf[i].value);
else
gpio_direction_input(gpio);
}
+ return 0;
+}
+
+int board_init(void)
+{
+ int board_type, hw_id;
+
+#ifndef CONFIG_USE_IRQ
+ irq_init();
+#endif
+ /* address of boot parameters, not used as booting with DTT */
+ gd->bd->bi_boot_params = 0;
+
+ enbw_cmc_init_gpio(enbw_gpio_config, ARRAY_SIZE(enbw_gpio_config));
+
+ /* detect HW version */
+ board_type = gpio_get_value(CONFIG_ENBW_CMC_BOARD_TYPE);
+ hw_id = gpio_get_value(CONFIG_ENBW_CMC_HW_ID_BIT0) +
+ (gpio_get_value(CONFIG_ENBW_CMC_HW_ID_BIT1) << 1) +
+ (gpio_get_value(CONFIG_ENBW_CMC_HW_ID_BIT2) << 2);
+ printf("BOARD: CMC-%s hw id: %d\n", (board_type ? "w2" : "hut"),
+ hw_id);
+ if (board_type)
+ enbw_cmc_init_gpio(enbw_gpio_config_w,
+ ARRAY_SIZE(enbw_gpio_config_w));
+ else
+ enbw_cmc_init_gpio(enbw_gpio_config_hut,
+ ARRAY_SIZE(enbw_gpio_config_hut));
+
/* setup the SUSPSRC for ARM to control emulation suspend */
clrbits_le32(&davinci_syscfg_regs->suspsrc,
(DAVINCI_SYSCFG_SUSPSRC_EMAC | DAVINCI_SYSCFG_SUSPSRC_I2C |
@@ -267,14 +311,231 @@
}
#ifdef CONFIG_DRIVER_TI_EMAC
+
+#define KSZ_CMD_READ 0x03
+#define KSZ_CMD_WRITE 0x02
+#define KSZ_ID 0x95
+
+static int enbw_cmc_switch_read(struct spi_slave *spi, u8 reg, u8 *val)
+{
+ unsigned long flags = SPI_XFER_BEGIN;
+ int ret;
+ int cmd_len;
+ u8 cmd[2];
+
+ cmd[0] = KSZ_CMD_READ;
+ cmd[1] = reg;
+ cmd_len = 2;
+
+ ret = spi_xfer(spi, cmd_len * 8, cmd, NULL, flags);
+ if (ret) {
+ debug("Failed to send command (%zu bytes): %d\n",
+ cmd_len, ret);
+ return -EINVAL;
+ }
+ flags |= SPI_XFER_END;
+ *val = 0;
+ cmd_len = 1;
+ ret = spi_xfer(spi, cmd_len * 8, NULL, val, flags);
+ if (ret) {
+ debug("Failed to read (%zu bytes): %d\n",
+ cmd_len, ret);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int enbw_cmc_switch_read_ident(struct spi_slave *spi)
+{
+ int ret;
+ u8 val;
+
+ ret = enbw_cmc_switch_read(spi, 0, &val);
+ if (ret) {
+ debug("Failed to read\n");
+ return -EINVAL;
+ }
+
+ if (val != KSZ_ID)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int enbw_cmc_switch_write(struct spi_slave *spi, unsigned long reg,
+ unsigned long val)
+{
+ unsigned long flags = SPI_XFER_BEGIN;
+ int ret;
+ int cmd_len;
+ u8 cmd[3];
+
+ cmd[0] = KSZ_CMD_WRITE;
+ cmd[1] = reg;
+ cmd[2] = val;
+ cmd_len = 3;
+ flags |= SPI_XFER_END;
+
+ ret = spi_xfer(spi, cmd_len * 8, cmd, NULL, flags);
+ if (ret) {
+ debug("Failed to send command (%zu bytes): %d\n",
+ cmd_len, ret);
+ return -EINVAL;
+ }
+
+ udelay(1000);
+ ret = enbw_cmc_switch_read(spi, reg, &cmd[0]);
+ if (ret) {
+ debug("Failed to read\n");
+ return -EINVAL;
+ }
+ if (val != cmd[0])
+ debug("warning: reg: %lx va: %x soll: %lx\n",
+ reg, cmd[0], val);
+
+ return 0;
+}
+
+static int enbw_cmc_eof(unsigned char *ptr)
+{
+ if (*ptr == 0xff)
+ return 1;
+
+ return 0;
+}
+
+static char *enbw_cmc_getnewline(char *ptr)
+{
+ while (*ptr != 0x0a) {
+ ptr++;
+ if (enbw_cmc_eof((unsigned char *)ptr))
+ return NULL;
+ }
+
+ ptr++;
+ return ptr;
+}
+
+static char *enbw_cmc_getvalue(char *ptr, int *value)
+{
+ int end = 0;
+
+ *value = -EINVAL;
+
+ if (!isxdigit(*ptr))
+ end = 1;
+
+ while (end) {
+ if ((*ptr == '#') || (*ptr == ';')) {
+ ptr = enbw_cmc_getnewline(ptr);
+ return ptr;
+ }
+ if (ptr != NULL) {
+ if (isxdigit(*ptr)) {
+ end = 0;
+ } else if (*ptr == 0x0a) {
+ ptr++;
+ return ptr;
+ } else {
+ ptr++;
+ if (enbw_cmc_eof((unsigned char *)ptr))
+ return NULL;
+ }
+ } else {
+ return NULL;
+ }
+ }
+ *value = (int)simple_strtoul((const char *)ptr, &ptr, 16);
+ ptr++;
+ return ptr;
+}
+
+static int enbw_cmc_config_switch(unsigned long addr)
+{
+ struct spi_slave *spi;
+ char *ptr = (char *)addr;
+ int value, reg;
+ int ret;
+ int bus, cs, max_hz, spi_mode;
+
+ debug("configure switch with file on addr: 0x%lx\n", addr);
+
+ bus = 0;
+ cs = 0;
+ max_hz = 1000000;
+ spi_mode = 0;
+
+ spi = spi_setup_slave(bus, cs, max_hz, spi_mode);
+ if (!spi) {
+ printf("Failed to set up slave\n");
+ return -EINVAL;
+ }
+
+ ret = spi_claim_bus(spi);
+ if (ret) {
+ debug("Failed to claim SPI bus: %d\n", ret);
+ goto err_claim_bus;
+ }
+
+ ret = enbw_cmc_switch_read_ident(spi);
+ if (ret)
+ goto err_claim_bus;
+
+ ptr = (char *)addr;
+ while (ptr != NULL) {
+ ptr = enbw_cmc_getvalue(ptr, ®);
+ if (ptr != NULL) {
+ ptr = enbw_cmc_getvalue(ptr, &value);
+ if ((ptr != NULL) && (value >= 0))
+ if (enbw_cmc_switch_write(spi, reg, value))
+ goto err_read;
+ }
+ }
+ return 0;
+
+err_read:
+ spi_release_bus(spi);
+err_claim_bus:
+ spi_free_slave(spi);
+ return -EINVAL;
+}
+
+static int do_switch(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
+{
+ unsigned long addr;
+
+ if (argc < 2)
+ return cmd_usage(cmdtp);
+
+ addr = simple_strtoul(argv[1], NULL, 16);
+ enbw_cmc_config_switch(addr);
+
+ return 0;
+}
+
+U_BOOT_CMD(switch, 3, 1, do_switch,
+ "switch addr",
+ "[addr]"
+);
+
/*
* Initializes on-board ethernet controllers.
*/
int board_eth_init(bd_t *bis)
{
-#ifdef CONFIG_DRIVER_TI_EMAC
+ const char *s;
+ size_t len;
+
davinci_emac_mii_mode_sel(0);
-#endif /* CONFIG_DRIVER_TI_EMAC */
+
+ /* send a config file to the switch */
+ s = hwconfig_subarg("switch", "config", &len);
+ if (len) {
+ unsigned long addr = simple_strtoul(s, NULL, 16);
+
+ enbw_cmc_config_switch(addr);
+ }
if (!davinci_emac_initialize()) {
printf("Error: Ethernet init failed!\n");
@@ -546,6 +807,29 @@
}
#endif
+ulong post_word_load(void)
+{
+ struct davinci_rtc *reg =
+ (struct davinci_rtc *)CONFIG_SYS_POST_WORD_ADDR;
+
+ return in_be32(®->scratch2);
+}
+
+void post_word_store(ulong value)
+{
+ struct davinci_rtc *reg =
+ (struct davinci_rtc *)CONFIG_SYS_POST_WORD_ADDR;
+
+ /*
+ * write RTC kick register to enable write
+ * for RTC Scratch registers. Cratch0 and 1 are
+ * used for bootcount values.
+ */
+ writel(RTC_KICK0R_WE, ®->kick0r);
+ writel(RTC_KICK1R_WE, ®->kick1r);
+ out_be32(®->scratch2, value);
+}
+
void board_gpio_init(void)
{
struct davinci_gpio *gpio = davinci_gpio_bank01;
@@ -558,6 +842,19 @@
clrbits_le32(&gpio->out_data, 0x8000407e);
/* set LED 1 - 5 to state on */
setbits_le32(&gpio->out_data, 0x8000001e);
+
+ /*
+ * set some gpio pins to low, this is needed early,
+ * so we have no gpio Interface here
+ * gpios:
+ * 8[8] Mode PV select low
+ * 8[9] Debug Rx Enable low
+ * 8[10] Mode Select PV low
+ * 8[11] Counter Interface RS485 Rx-Enable low
+ */
+ gpio = davinci_gpio_bank8;
+ clrbits_le32(&gpio->dir, 0x00000f00);
+ clrbits_le32(&gpio->out_data, 0x0f00);
}
int board_late_init(void)