nios2: add 10m50 devboard support
Add 10m50 devboard support. It is based on the Golden Hardware
Reference Design (GHRD), available at,
http://rocketboards.org/foswiki/view/Documentation/
AlteraMAX1010M50RevCDevelopmentKitLinuxSetup
Though we supported only one nios2-generic board in the past. Now,
with the removal of the nios2-generic board dir, adding new nios2
boards to u-boot is easier than before. It should be helpful to
add those boards supported in Linux mainline. There are only two
such nios2 boards, the 3c120 devboard and 10m50 devboard. The
nios2-generic is actually 3c120, and should restore the name. The
10m50 is this one.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
diff --git a/arch/nios2/dts/10m50_devboard.dts b/arch/nios2/dts/10m50_devboard.dts
new file mode 100644
index 0000000..e89dbb2
--- /dev/null
+++ b/arch/nios2/dts/10m50_devboard.dts
@@ -0,0 +1,267 @@
+/*
+ * Copyright (C) 2015 Altera Corporation
+ *
+ * This file is generated by sopc2dts.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/dts-v1/;
+
+/ {
+ model = "Altera NiosII Max10";
+ compatible = "altr,niosii-max10";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu: cpu@0 {
+ device_type = "cpu";
+ compatible = "altr,nios2-1.1";
+ reg = <0x00000000>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ altr,exception-addr = <0xc8000120>;
+ altr,fast-tlb-miss-addr = <0xc0000100>;
+ altr,has-div = <1>;
+ altr,has-initda = <1>;
+ altr,has-mmu = <1>;
+ altr,has-mul = <1>;
+ altr,implementation = "fast";
+ altr,pid-num-bits = <8>;
+ altr,reset-addr = <0xd4000000>;
+ altr,tlb-num-entries = <256>;
+ altr,tlb-num-ways = <16>;
+ altr,tlb-ptr-sz = <8>;
+ clock-frequency = <75000000>;
+ dcache-line-size = <32>;
+ dcache-size = <32768>;
+ icache-line-size = <32>;
+ icache-size = <32768>;
+ };
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x08000000 0x08000000>,
+ <0x00000000 0x00000400>;
+ };
+
+ sopc0: sopc@0 {
+ device_type = "soc";
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "altr,avalon", "simple-bus";
+ bus-frequency = <75000000>;
+
+ jtag_uart: serial@18001530 {
+ compatible = "altr,juart-1.0";
+ reg = <0x18001530 0x00000008>;
+ interrupt-parent = <&cpu>;
+ interrupts = <7>;
+ };
+
+ a_16550_uart_0: serial@18001600 {
+ compatible = "altr,16550-FIFO32", "ns16550a";
+ reg = <0x18001600 0x00000200>;
+ interrupt-parent = <&cpu>;
+ interrupts = <1>;
+ auto-flow-control = <1>;
+ clock-frequency = <50000000>;
+ fifo-size = <32>;
+ reg-io-width = <4>;
+ reg-shift = <2>;
+ };
+
+ ext_flash: quadspi@0x180014a0 {
+ compatible = "altr,quadspi-1.0";
+ reg = <0x180014a0 0x00000020>,
+ <0x14000000 0x04000000>;
+ reg-names = "avl_csr", "avl_mem";
+ interrupt-parent = <&cpu>;
+ interrupts = <4>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ flash0: nor0@0 {
+ compatible = "micron,n25q512a";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
+ };
+
+ sysid: sysid@18001528 {
+ compatible = "altr,sysid-1.0";
+ reg = <0x18001528 0x00000008>;
+ };
+
+ rgmii_0_eth_tse_0: ethernet@400 {
+ compatible = "altr,tse-msgdma-1.0", "altr,tse-1.0";
+ reg = <0x00000400 0x00000400>,
+ <0x00000820 0x00000020>,
+ <0x00000800 0x00000020>,
+ <0x000008c0 0x00000008>,
+ <0x00000840 0x00000020>,
+ <0x00000860 0x00000020>;
+ reg-names = "control_port", "rx_csr", "rx_desc", "rx_resp",
+ "tx_csr", "tx_desc";
+ interrupt-parent = <&cpu>;
+ interrupts = <2 3>;
+ interrupt-names = "rx_irq", "tx_irq";
+ rx-fifo-depth = <8192>;
+ tx-fifo-depth = <8192>;
+ address-bits = <48>;
+ max-frame-size = <1518>;
+ local-mac-address = [00 00 00 00 00 00];
+ altr,has-supplementary-unicast;
+ altr,enable-sup-addr = <1>;
+ altr,has-hash-multicast-filter;
+ altr,enable-hash = <1>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&phy0>;
+ rgmii_0_eth_tse_0_mdio: mdio {
+ compatible = "altr,tse-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ device_type = "ethernet-phy";
+ };
+ };
+ };
+
+ enet_pll: clock@0 {
+ compatible = "altr,pll-1.0";
+ #clock-cells = <1>;
+
+ enet_pll_c0: enet_pll_c0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <125000000>;
+ clock-output-names = "enet_pll-c0";
+ };
+
+ enet_pll_c1: enet_pll_c1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ clock-output-names = "enet_pll-c1";
+ };
+
+ enet_pll_c2: enet_pll_c2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <2500000>;
+ clock-output-names = "enet_pll-c2";
+ };
+ };
+
+ sys_pll: clock@1 {
+ compatible = "altr,pll-1.0";
+ #clock-cells = <1>;
+
+ sys_pll_c0: sys_pll_c0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sys_pll-c0";
+ };
+
+ sys_pll_c1: sys_pll_c1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <50000000>;
+ clock-output-names = "sys_pll-c1";
+ };
+
+ sys_pll_c2: sys_pll_c2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <75000000>;
+ clock-output-names = "sys_pll-c2";
+ };
+ };
+
+ sys_clk_timer: timer@18001440 {
+ compatible = "altr,timer-1.0";
+ reg = <0x18001440 0x00000020>;
+ interrupt-parent = <&cpu>;
+ interrupts = <0>;
+ clock-frequency = <75000000>;
+ };
+
+ led_pio: gpio@180014d0 {
+ compatible = "altr,pio-1.0";
+ reg = <0x180014d0 0x00000010>;
+ altr,gpio-bank-width = <4>;
+ resetvalue = <15>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-bank-name = "led";
+ };
+
+ uart_0: serial@0x18001420 {
+ compatible = "altr,uart-1.0";
+ reg = <0x18001420 0x00000020>;
+ interrupt-parent = <&cpu>;
+ interrupts = <1>;
+ clock-frequency = <75000000>;
+ current-speed = <115200>;
+ };
+
+ button_pio: gpio@180014c0 {
+ compatible = "altr,pio-1.0";
+ reg = <0x180014c0 0x00000010>;
+ interrupt-parent = <&cpu>;
+ interrupts = <6>;
+ altr,gpio-bank-width = <3>;
+ altr,interrupt-type = <2>;
+ edge_type = <1>;
+ level_trigger = <0>;
+ resetvalue = <0>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ gpio-bank-name = "button";
+ };
+
+ sys_clk_timer_1: timer@880 {
+ compatible = "altr,timer-1.0";
+ reg = <0x00000880 0x00000020>;
+ interrupt-parent = <&cpu>;
+ interrupts = <5>;
+ clock-frequency = <75000000>;
+ };
+
+ fpga_leds: leds {
+ compatible = "gpio-leds";
+
+ led_fpga0: fpga0 {
+ label = "fpga_led0";
+ gpios = <&led_pio 0 1>;
+ };
+
+ led_fpga1: fpga1 {
+ label = "fpga_led1";
+ gpios = <&led_pio 1 1>;
+ };
+
+ led_fpga2: fpga2 {
+ label = "fpga_led2";
+ gpios = <&led_pio 2 1>;
+ };
+
+ led_fpga3: fpga3 {
+ label = "fpga_led3";
+ gpios = <&led_pio 3 1>;
+ };
+ };
+ };
+
+ chosen {
+ bootargs = "debug console=ttyS0,115200";
+ stdout-path = &uart_0;
+ };
+};