drivers: Use CONFIG_XPL_BUILD instead of CONFIG_SPL_BUILD
Use the new symbol to refer to any 'SPL' build, including TPL and VPL
Signed-off-by: Simon Glass <sjg@chromium.org>
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 78810f9..66bd30b 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -63,7 +63,7 @@
obj-$(CONFIG_XTENSA_SEMIHOSTING_SERIAL) += serial_xtensa_semihosting.o
obj-$(CONFIG_S5P4418_PL011_SERIAL) += serial_s5p4418_pl011.o
-ifndef CONFIG_SPL_BUILD
+ifndef CONFIG_XPL_BUILD
obj-$(CONFIG_USB_TTY) += usbtty.o
endif
obj-$(CONFIG_UART4_SERIAL) += serial_adi_uart4.o
diff --git a/drivers/serial/atmel_usart.c b/drivers/serial/atmel_usart.c
index 7e45a80..0b35582 100644
--- a/drivers/serial/atmel_usart.c
+++ b/drivers/serial/atmel_usart.c
@@ -218,7 +218,7 @@
.setbrg = atmel_serial_setbrg,
};
-#if defined(CONFIG_SPL_BUILD) && !defined(CONFIG_SPL_CLK)
+#if defined(CONFIG_XPL_BUILD) && !defined(CONFIG_SPL_CLK)
static int atmel_serial_enable_clk(struct udevice *dev)
{
struct atmel_serial_priv *priv = dev_get_priv(dev);
diff --git a/drivers/serial/ns16550.c b/drivers/serial/ns16550.c
index 55bc396..3489228 100644
--- a/drivers/serial/ns16550.c
+++ b/drivers/serial/ns16550.c
@@ -227,7 +227,7 @@
void ns16550_init(struct ns16550 *com_port, int baud_divisor)
{
-#if defined(CONFIG_SPL_BUILD) && defined(CONFIG_OMAP34XX)
+#if defined(CONFIG_XPL_BUILD) && defined(CONFIG_OMAP34XX)
/*
* On some OMAP3/OMAP4 devices when UART3 is configured for boot mode
* before SPL starts only THRE bit is set. We have to empty the
@@ -303,7 +303,7 @@
char ns16550_getc(struct ns16550 *com_port)
{
while ((serial_in(&com_port->lsr) & UART_LSR_DR) == 0) {
-#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_USB_TTY)
+#if !defined(CONFIG_XPL_BUILD) && defined(CONFIG_USB_TTY)
extern void usbtty_poll(void);
usbtty_poll();
#endif
diff --git a/drivers/serial/serial-uclass.c b/drivers/serial/serial-uclass.c
index 84f02f7..9feaa1e 100644
--- a/drivers/serial/serial-uclass.c
+++ b/drivers/serial/serial-uclass.c
@@ -101,7 +101,7 @@
}
}
}
- if (!IS_ENABLED(CONFIG_SPL_BUILD) || !CONFIG_IS_ENABLED(OF_CONTROL) ||
+ if (!IS_ENABLED(CONFIG_XPL_BUILD) || !CONFIG_IS_ENABLED(OF_CONTROL) ||
!blob) {
/*
* Try to use CONFIG_CONS_INDEX if available (it is numbered
diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index dc4bb06..e10ca6e 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -315,7 +315,7 @@
/* We must have a console device */
if (!dev) {
-#ifdef CONFIG_SPL_BUILD
+#ifdef CONFIG_XPL_BUILD
puts("Cannot find console\n");
hang();
#else
diff --git a/drivers/serial/serial_s5p.c b/drivers/serial/serial_s5p.c
index 801b764..734780a 100644
--- a/drivers/serial/serial_s5p.c
+++ b/drivers/serial/serial_s5p.c
@@ -117,7 +117,7 @@
writeb(val % 16, &uart->rest.value);
}
-#ifndef CONFIG_SPL_BUILD
+#ifndef CONFIG_XPL_BUILD
int s5p_serial_setbrg(struct udevice *dev, int baudrate)
{
struct s5p_serial_plat *plat = dev_get_plat(dev);
diff --git a/drivers/serial/serial_zynq.c b/drivers/serial/serial_zynq.c
index 55f13c0..b74712f 100644
--- a/drivers/serial/serial_zynq.c
+++ b/drivers/serial/serial_zynq.c
@@ -152,7 +152,7 @@
return 0;
}
-#if !defined(CONFIG_SPL_BUILD)
+#if !defined(CONFIG_XPL_BUILD)
static int zynq_serial_setconfig(struct udevice *dev, uint serial_config)
{
struct zynq_uart_plat *plat = dev_get_plat(dev);