ehci: msm: switch to generic PHY uclass
All the underlying USB PHY was handled in the ehci driver.
Use the generic phy API instead.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index b4dd005..a213c91 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -167,12 +167,11 @@
bool "Support for Qualcomm on-chip EHCI USB controller"
depends on DM_USB
select USB_ULPI_VIEWPORT
+ select MSM8916_USB_PHY
default n
---help---
Enables support for the on-chip EHCI controller on Qualcomm
Snapdragon SoCs.
- This driver supports combination of Chipidea USB controller
- and Synapsys USB PHY in host mode only.
config USB_EHCI_PCI
bool "Support for PCI-based EHCI USB controller"
diff --git a/drivers/usb/host/ehci-msm.c b/drivers/usb/host/ehci-msm.c
index e7fb76d..a27a583 100644
--- a/drivers/usb/host/ehci-msm.c
+++ b/drivers/usb/host/ehci-msm.c
@@ -21,59 +21,19 @@
#include <linux/compat.h>
#include "ehci.h"
-/* PHY viewport regs */
-#define ULPI_MISC_A_READ 0x96
-#define ULPI_MISC_A_SET 0x97
-#define ULPI_MISC_A_CLEAR 0x98
-#define ULPI_MISC_A_VBUSVLDEXTSEL (1 << 1)
-#define ULPI_MISC_A_VBUSVLDEXT (1 << 0)
-
-#define GEN2_SESS_VLD_CTRL_EN (1 << 7)
-
-#define SESS_VLD_CTRL (1 << 25)
-
struct msm_ehci_priv {
struct ehci_ctrl ctrl; /* Needed by EHCI */
struct usb_ehci *ehci; /* Start of IP core*/
struct ulpi_viewport ulpi_vp; /* ULPI Viewport */
+ struct phy phy;
};
-static void setup_usb_phy(struct msm_ehci_priv *priv)
-{
- /* Select and enable external configuration with USB PHY */
- ulpi_write(&priv->ulpi_vp, (u8 *)ULPI_MISC_A_SET,
- ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT);
-}
-
-static void reset_usb_phy(struct msm_ehci_priv *priv)
-{
- /* Disable VBUS mimicing in the controller. */
- ulpi_write(&priv->ulpi_vp, (u8 *)ULPI_MISC_A_CLEAR,
- ULPI_MISC_A_VBUSVLDEXTSEL | ULPI_MISC_A_VBUSVLDEXT);
-}
-
-
static int msm_init_after_reset(struct ehci_ctrl *dev)
{
struct msm_ehci_priv *p = container_of(dev, struct msm_ehci_priv, ctrl);
struct usb_ehci *ehci = p->ehci;
- /* select ULPI phy */
- writel(PORT_PTS_ULPI, &ehci->portsc);
- setup_usb_phy(p);
-
- /* Enable sess_vld */
- setbits_le32(&ehci->genconfig2, GEN2_SESS_VLD_CTRL_EN);
-
- /* Enable external vbus configuration in the LINK */
- setbits_le32(&ehci->usbcmd, SESS_VLD_CTRL);
-
- /* USB_OTG_HS_AHB_BURST */
- writel(0x0, &ehci->sbuscfg);
-
- /* USB_OTG_HS_AHB_MODE: HPROT_MODE */
- /* Bus access related config. */
- writel(0x08, &ehci->sbusmode);
+ generic_phy_reset(&p->phy);
/* set mode to host controller */
writel(CM_HOST, &ehci->usbmode);
@@ -97,6 +57,10 @@
hcor = (struct ehci_hcor *)((phys_addr_t)hccr +
HC_LENGTH(ehci_readl(&(hccr)->cr_capbase)));
+ ret = ehci_setup_phy(dev, &p->phy, 0);
+ if (ret)
+ return ret;
+
ret = board_usb_init(0, USB_INIT_HOST);
if (ret < 0)
return ret;
@@ -117,7 +81,9 @@
/* Stop controller. */
clrbits_le32(&ehci->usbcmd, CMD_RUN);
- reset_usb_phy(p);
+ ret = ehci_shutdown_phy(dev, &p->phy);
+ if (ret)
+ return ret;
ret = board_usb_init(0, USB_INIT_DEVICE); /* Board specific hook */
if (ret < 0)