armv8: ls2080ardb: Add QSPI-boot support
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
diff --git a/include/configs/ls2080ardb.h b/include/configs/ls2080ardb.h
index ec83eb5..ef95358 100644
--- a/include/configs/ls2080ardb.h
+++ b/include/configs/ls2080ardb.h
@@ -1,4 +1,5 @@
/*
+ * Copyright 2017 NXP
* Copyright 2015 Freescale Semiconductor
*
* SPDX-License-Identifier: GPL-2.0+
@@ -12,6 +13,11 @@
#undef CONFIG_CONS_INDEX
#define CONFIG_CONS_INDEX 2
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SYS_I2C_EARLY_INIT
+#define CONFIG_DISPLAY_BOARDINFO_LATE
+#endif
+
#define I2C_MUX_CH_VOL_MONITOR 0xa
#define I2C_VOL_MONITOR_ADDR 0x38
#define CONFIG_VOL_MONITOR_IR36021_READ
@@ -69,6 +75,7 @@
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
+#ifndef CONFIG_FSL_QSPI
/* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
#define CONFIG_SYS_NOR0_CSPR_EXT (0x0)
@@ -157,7 +164,6 @@
#define CONFIG_CMD_NAND
#define CONFIG_SYS_NAND_BLOCK_SIZE (512 * 1024)
-
#define CONFIG_FSL_QIXIS /* use common QIXIS code */
#define QIXIS_LBMAP_SWITCH 0x06
#define QIXIS_LBMAP_MASK 0x0f
@@ -250,7 +256,7 @@
/* Debug Server firmware */
#define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
#define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
-
+#endif
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
/*
@@ -263,10 +269,17 @@
#define I2C_MUX_CH_DEFAULT 0x8
/* SPI */
-#ifdef CONFIG_FSL_DSPI
+#if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
#define CONFIG_SPI_FLASH
+#ifdef CONFIG_FSL_QSPI
#define CONFIG_SPI_FLASH_STMICRO
#endif
+#ifdef CONFIG_FSL_QSPI
+#define CONFIG_SPI_FLASH_SPANSION
+#define FSL_QSPI_FLASH_SIZE SZ_64M /* 64MB */
+#define FSL_QSPI_FLASH_NUM 2
+#endif
+#endif
/*
* RTC configuration
@@ -345,6 +358,25 @@
" 0x580800000 \0" \
BOOTENV
#else
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "hwconfig=fsl_ddr:bank_intlv=auto\0" \
+ "scriptaddr=0x80800000\0" \
+ "kernel_addr_r=0x81000000\0" \
+ "pxefile_addr_r=0x81000000\0" \
+ "fdt_addr_r=0x88000000\0" \
+ "ramdisk_addr_r=0x89000000\0" \
+ "loadaddr=0x80100000\0" \
+ "kernel_addr=0x100000\0" \
+ "ramdisk_size=0x2000000\0" \
+ "fdt_high=0xa0000000\0" \
+ "initrd_high=0xffffffffffffffff\0" \
+ "kernel_start=0x21000000\0" \
+ "mcmemsize=0x40000000\0" \
+ "mcinitcmd=fsl_mc start mc 0x20a00000" \
+ " 0x20e00000 \0" \
+ BOOTENV
+#else
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"scriptaddr=0x80800000\0" \
@@ -367,6 +399,7 @@
" 0x580800000 \0" \
BOOTENV
#endif
+#endif
#undef CONFIG_BOOTARGS
@@ -376,11 +409,18 @@
" hugepagesz=2m hugepages=256"
#undef CONFIG_BOOTCOMMAND
+#ifdef CONFIG_QSPI_BOOT
+/* Try to boot an on-QSPI kernel first, then do normal distro boot */
+#define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x20d00000" \
+ " && bootm $kernel_start" \
+ " || run distro_bootcmd"
+#else
/* Try to boot an on-NOR kernel first, then do normal distro boot */
#define CONFIG_BOOTCOMMAND "run mcinitcmd && fsl_mc lazyapply dpl 0x580700000" \
" && cp.b $kernel_start $kernel_load $kernel_size" \
" && bootm $kernel_load" \
" || run distro_bootcmd"
+#endif
/* MAC/PHY configuration */
#ifdef CONFIG_FSL_MC_ENET
@@ -389,7 +429,11 @@
#define CONFIG_PHY_CORTINA
#define CONFIG_PHYLIB
#define CONFIG_SYS_CORTINA_FW_IN_NOR
+#ifdef CONFIG_QSPI_BOOT
+#define CONFIG_CORTINA_FW_ADDR 0x20980000
+#else
#define CONFIG_CORTINA_FW_ADDR 0x581000000
+#endif
#define CONFIG_CORTINA_FW_LENGTH 0x40000
#define CORTINA_PHY_ADDR1 0x10