diff --git a/include/configs/k2hk_evm.h b/include/configs/k2hk_evm.h
new file mode 100644
index 0000000..9d0ba24
--- /dev/null
+++ b/include/configs/k2hk_evm.h
@@ -0,0 +1,212 @@
+/*
+ * Configuration header file for TI's k2hk-evm
+ *
+ * (C) Copyright 2012-2014
+ *     Texas Instruments Incorporated, <www.ti.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#ifndef __CONFIG_K2HK_EVM_H
+#define __CONFIG_K2HK_EVM_H
+
+/* Platform type */
+#define CONFIG_SOC_K2HK
+#define CONFIG_K2HK_EVM
+
+/* U-Boot Build Configuration */
+#define CONFIG_SKIP_LOWLEVEL_INIT       /* U-Boot is a 2nd stage loader */
+#define CONFIG_SYS_NO_FLASH             /* that is, no *NOR* flash */
+#define CONFIG_SYS_CONSOLE_INFO_QUIET
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_SYS_THUMB_BUILD
+
+/* SoC Configuration */
+#define CONFIG_ARMV7
+#define CONFIG_ARCH_CPU_INIT
+#define CONFIG_SYS_ARCH_TIMER
+#define CONFIG_SYS_HZ                   1000
+#define CONFIG_SYS_TEXT_BASE            0x0c001000
+#define CONFIG_SPL_TARGET               "u-boot-spi.gph"
+#define CONFIG_SYS_DCACHE_OFF
+
+/* Memory Configuration */
+#define CONFIG_NR_DRAM_BANKS            2
+#define CONFIG_SYS_SDRAM_BASE           0x80000000
+#define CONFIG_SYS_LPAE_SDRAM_BASE      0x800000000
+#define CONFIG_MAX_RAM_BANK_SIZE        (2 << 30)       /* 2GB */
+#define CONFIG_STACKSIZE                (512 << 10)     /* 512 KiB */
+#define CONFIG_SYS_MALLOC_LEN           (4 << 20)       /* 4 MiB */
+#define CONFIG_SYS_INIT_SP_ADDR         (CONFIG_SYS_TEXT_BASE - \
+					 GENERATED_GBL_DATA_SIZE)
+
+/* SPL SPI Loader Configuration */
+#define CONFIG_SPL_TEXT_BASE            0x0c200000
+#define CONFIG_SPL_PAD_TO               65536
+#define CONFIG_SPL_MAX_SIZE             (CONFIG_SPL_PAD_TO - 8)
+#define CONFIG_SPL_BSS_START_ADDR       (CONFIG_SPL_TEXT_BASE + \
+					 CONFIG_SPL_MAX_SIZE)
+#define CONFIG_SPL_BSS_MAX_SIZE         (32 * 1024)
+#define CONFIG_SYS_SPL_MALLOC_START     (CONFIG_SPL_BSS_START_ADDR + \
+					 CONFIG_SPL_BSS_MAX_SIZE)
+#define CONFIG_SYS_SPL_MALLOC_SIZE      (32 * 1024)
+#define CONFIG_SPL_STACK_SIZE           (8 * 1024)
+#define CONFIG_SPL_STACK                (CONFIG_SYS_SPL_MALLOC_START + \
+					 CONFIG_SYS_SPL_MALLOC_SIZE + \
+					 CONFIG_SPL_STACK_SIZE - 4)
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_SPI_FLASH_SUPPORT
+#define CONFIG_SPL_SPI_SUPPORT
+#define CONFIG_SPL_BOARD_INIT
+#define CONFIG_SPL_SPI_LOAD
+#define CONFIG_SPL_SPI_BUS              0
+#define CONFIG_SPL_SPI_CS               0
+#define CONFIG_SYS_SPI_U_BOOT_OFFS      CONFIG_SPL_PAD_TO
+#define CONFIG_SPL_FRAMEWORK
+
+/* UART Configuration */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_MEM32
+#define CONFIG_SYS_NS16550_REG_SIZE     -4
+#define CONFIG_SYS_NS16550_COM1         K2HK_UART0_BASE
+#define CONFIG_SYS_NS16550_CLK          clk_get_rate(K2HK_CLK1_6)
+#define CONFIG_CONS_INDEX               1
+#define CONFIG_BAUDRATE                 115200
+
+/* SPI Configuration */
+#define CONFIG_SPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_DAVINCI_SPI
+#define CONFIG_SYS_SPI_BASE             K2HK_SPI_BASE
+#define CONFIG_SYS_SPI_CLK              clk_get_rate(K2HK_LPSC_EMIF25_SPI)
+#define CONFIG_SF_DEFAULT_SPEED         30000000
+#define CONFIG_ENV_SPI_MAX_HZ           CONFIG_SF_DEFAULT_SPEED
+
+/* I2C Configuration */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_DAVINCI
+#define CONFIG_SYS_DAVINCI_I2C_SPEED    100000
+#define CONFIG_SYS_DAVINCI_I2C_SLAVE    0x10 /* SMBus host address */
+#define CONFIG_SYS_DAVINCI_I2C_SPEED1   100000
+#define CONFIG_SYS_DAVINCI_I2C_SLAVE1   0x10 /* SMBus host address */
+#define CONFIG_SYS_DAVINCI_I2C_SPEED2   100000
+#define CONFIG_SYS_DAVINCI_I2C_SLAVE2   0x10 /* SMBus host address */
+#define I2C_BUS_MAX                     3
+
+/* EEPROM definitions */
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN         2
+#define CONFIG_SYS_I2C_EEPROM_ADDR             0x50
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS      6
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS  20
+#define CONFIG_ENV_EEPROM_IS_ON_I2C
+
+/* NAND Configuration */
+#define CONFIG_NAND_DAVINCI
+#define CONFIG_SYS_NAND_CS                     2
+#define CONFIG_SYS_NAND_USE_FLASH_BBT
+#define CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
+#define CONFIG_SYS_NAND_PAGE_2K
+
+#define CONFIG_SYS_NAND_LARGEPAGE
+#define CONFIG_SYS_NAND_BASE_LIST       { 0x30000000, }
+#define CONFIG_SYS_MAX_NAND_DEVICE      1
+#define CONFIG_SYS_NAND_MAX_CHIPS       1
+#define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE
+#define CONFIG_ENV_SIZE                 (256 << 10)  /* 256 KiB */
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_OFFSET               0x100000
+#define CONFIG_MTD_PARTITIONS
+#define CONFIG_MTD_DEVICE
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define MTDPARTS_DEFAULT                "mtdparts=davinci_nand.0:" \
+					"1024k(bootloader)ro,512k(params)ro," \
+					"-(ubifs)"
+/* U-Boot command configuration */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SAVES
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_CMD_SF
+#define CONFIG_CMD_EEPROM
+
+/* U-Boot general configuration */
+#define CONFIG_SYS_PROMPT               "K2HK EVM # "
+#define CONFIG_SYS_CBSIZE               1024
+#define CONFIG_SYS_PBSIZE		2048
+#define CONFIG_SYS_MAXARGS              16
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_CRC32_VERIFY
+#define CONFIG_MX_CYCLIC
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_TIMESTAMP
+
+#define CONFIG_BOOTDELAY                3
+#define CONFIG_BOOTFILE                 "uImage"
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"boot=ramfs\0"							\
+	"tftp_root=/\0"							\
+	"nfs_root=/export\0"						\
+	"mem_lpae=1\0"							\
+	"mem_reserve=512M\0"						\
+	"addr_fdt=0x87000000\0"						\
+	"addr_kern=0x88000000\0"					\
+	"addr_mon=0x0c5f0000\0"						\
+	"addr_uboot=0x87000000\0"					\
+	"addr_fs=0x82000000\0"						\
+	"addr_ubi=0x82000000\0"						\
+	"fdt_high=0xffffffff\0"						\
+	"run_mon=mon_install ${addr_mon}\0"				\
+	"run_kern=bootm ${addr_kern} - ${addr_fdt}\0"			\
+	"init_ubi=run args_all args_ubi; "				\
+		"ubi part ubifs; ubifsmount boot\0"			\
+	"get_fdt_ubi=ubifsload ${addr_fdt} ${name_fdt}\0"		\
+	"get_kern_ubi=ubifsload ${addr_kern} ${name_kern}\0"		\
+	"get_mon_ubi=ubifsload ${addr_mon} ${name_mon}\0"		\
+	"burn_uboot=sf probe; sf erase 0 0x100000; "			\
+		"sf write ${addr_uboot} 0 ${filesize}\0"		\
+	"args_all=setenv bootargs console=ttyS0,115200n8 rootwait=1\0"	\
+	"args_ubi=setenv bootargs ${bootargs} rootfstype=ubifs "	\
+		"root=ubi0:rootfs rootflags=sync rw ubi.mtd=2,2048\0"	\
+	"burn_ubi=nand erase.part ubifs; "				\
+		"nand write ${addr_ubi} ubifs ${filesize}\0"		\
+	"init_ramfs=run args_all args_ramfs get_fs_ramfs\0"		\
+	"args_ramfs=setenv bootargs ${bootargs} earlyprintk "		\
+		"rdinit=/sbin/init rw root=/dev/ram0 "			\
+		"initrd=0x802000000,9M\0"				\
+	"mtdparts=mtdparts=davinci_nand.0:"				\
+		"1024k(bootloader)ro,512k(params)ro,522752k(ubifs)\0"
+#define CONFIG_BOOTCOMMAND						\
+	"run init_${boot} get_fdt_${boot} get_mon_${boot} "		\
+		"get_kern_${boot} run_mon run_kern"
+#define CONFIG_BOOTARGS							\
+
+/* Linux interfacing */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_OF_LIBFDT                1
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_SYS_BARGSIZE             1024
+#define CONFIG_SYS_LOAD_ADDR            (CONFIG_SYS_SDRAM_BASE + 0x08000000)
+
+#define CONFIG_SUPPORT_RAW_INITRD
+
+/* we may include files below only after all above definitions */
+#include <asm/arch/hardware.h>
+#include <asm/arch/clock.h>
+#define CONFIG_SYS_HZ_CLOCK             clk_get_rate(K2HK_CLK1_6)
+
+#endif /* __CONFIG_K2HK_EVM_H */