net: add altera triple speeds ethernet mac driver
This driver supports the Altera triple speeds 10/100/1000 ethernet
mac.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
diff --git a/drivers/net/altera_tse.h b/drivers/net/altera_tse.h
new file mode 100644
index 0000000..c1cb79e
--- /dev/null
+++ b/drivers/net/altera_tse.h
@@ -0,0 +1,494 @@
+/*
+ * Altera 10/100/1000 triple speed ethernet mac
+ *
+ * Copyright (C) 2008 Altera Corporation.
+ * Copyright (C) 2010 Thomas Chou <thomas@wytron.com.tw>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef _ALTERA_TSE_H_
+#define _ALTERA_TSE_H_
+
+#define __packed_1_ __attribute__ ((packed, aligned(1)))
+
+/* PHY Stuff */
+#define miim_end -2
+#define miim_read -1
+
+#define PHY_AUTONEGOTIATE_TIMEOUT 5000 /* in ms */
+
+#ifndef CONFIG_SYS_TBIPA_VALUE
+#define CONFIG_SYS_TBIPA_VALUE 0x1f
+#endif
+#define MIIMCFG_INIT_VALUE 0x00000003
+#define MIIMCFG_RESET 0x80000000
+
+#define MIIMIND_BUSY 0x00000001
+#define MIIMIND_NOTVALID 0x00000004
+
+#define MIIM_CONTROL 0x00
+#define MIIM_CONTROL_RESET 0x00009140
+#define MIIM_CONTROL_INIT 0x00001140
+#define MIIM_CONTROL_RESTART 0x00001340
+#define MIIM_ANEN 0x00001000
+
+#define MIIM_CR 0x00
+#define MIIM_CR_RST 0x00008000
+#define MIIM_CR_INIT 0x00001000
+
+#define MIIM_STATUS 0x1
+#define MIIM_STATUS_AN_DONE 0x00000020
+#define MIIM_STATUS_LINK 0x0004
+#define PHY_BMSR_AUTN_ABLE 0x0008
+#define PHY_BMSR_AUTN_COMP 0x0020
+
+#define MIIM_PHYIR1 0x2
+#define MIIM_PHYIR2 0x3
+
+#define MIIM_ANAR 0x4
+#define MIIM_ANAR_INIT 0x1e1
+
+#define MIIM_TBI_ANLPBPA 0x5
+#define MIIM_TBI_ANLPBPA_HALF 0x00000040
+#define MIIM_TBI_ANLPBPA_FULL 0x00000020
+
+#define MIIM_TBI_ANEX 0x6
+#define MIIM_TBI_ANEX_NP 0x00000004
+#define MIIM_TBI_ANEX_PRX 0x00000002
+
+#define MIIM_GBIT_CONTROL 0x9
+#define MIIM_GBIT_CONTROL_INIT 0xe00
+
+#define MIIM_EXT_PAGE_ACCESS 0x1f
+
+/* 88E1011 PHY Status Register */
+#define MIIM_88E1011_PHY_STATUS 0x11
+#define MIIM_88E1011_PHYSTAT_SPEED 0xc000
+#define MIIM_88E1011_PHYSTAT_GBIT 0x8000
+#define MIIM_88E1011_PHYSTAT_100 0x4000
+#define MIIM_88E1011_PHYSTAT_DUPLEX 0x2000
+#define MIIM_88E1011_PHYSTAT_SPDDONE 0x0800
+#define MIIM_88E1011_PHYSTAT_LINK 0x0400
+
+#define MIIM_88E1011_PHY_SCR 0x10
+#define MIIM_88E1011_PHY_MDI_X_AUTO 0x0060
+
+#define MIIM_88E1111_PHY_EXT_CR 0x14
+#define MIIM_88E1111_PHY_EXT_SR 0x1b
+
+/* 88E1111 PHY LED Control Register */
+#define MIIM_88E1111_PHY_LED_CONTROL 24
+#define MIIM_88E1111_PHY_LED_DIRECT 0x4100
+#define MIIM_88E1111_PHY_LED_COMBINE 0x411C
+
+#define MIIM_READ_COMMAND 0x00000001
+
+/* struct phy_info: a structure which defines attributes for a PHY
+ * id will contain a number which represents the PHY. During
+ * startup, the driver will poll the PHY to find out what its
+ * UID--as defined by registers 2 and 3--is. The 32-bit result
+ * gotten from the PHY will be shifted right by "shift" bits to
+ * discard any bits which may change based on revision numbers
+ * unimportant to functionality
+ *
+ * The struct phy_cmd entries represent pointers to an arrays of
+ * commands which tell the driver what to do to the PHY.
+ */
+struct phy_info {
+ uint id;
+ char *name;
+ uint shift;
+ /* Called to configure the PHY, and modify the controller
+ * based on the results */
+ struct phy_cmd *config;
+
+ /* Called when starting up the controller */
+ struct phy_cmd *startup;
+
+ /* Called when bringing down the controller */
+ struct phy_cmd *shutdown;
+};
+
+/* SGDMA Stuff */
+#define ALT_SGDMA_STATUS_ERROR_MSK (0x00000001)
+#define ALT_SGDMA_STATUS_EOP_ENCOUNTERED_MSK (0x00000002)
+#define ALT_SGDMA_STATUS_DESC_COMPLETED_MSK (0x00000004)
+#define ALT_SGDMA_STATUS_CHAIN_COMPLETED_MSK (0x00000008)
+#define ALT_SGDMA_STATUS_BUSY_MSK (0x00000010)
+
+#define ALT_SGDMA_CONTROL_IE_ERROR_MSK (0x00000001)
+#define ALT_SGDMA_CONTROL_IE_EOP_ENCOUNTERED_MSK (0x00000002)
+#define ALT_SGDMA_CONTROL_IE_DESC_COMPLETED_MSK (0x00000004)
+#define ALT_SGDMA_CONTROL_IE_CHAIN_COMPLETED_MSK (0x00000008)
+#define ALT_SGDMA_CONTROL_IE_GLOBAL_MSK (0x00000010)
+#define ALT_SGDMA_CONTROL_RUN_MSK (0x00000020)
+#define ALT_SGDMA_CONTROL_STOP_DMA_ER_MSK (0x00000040)
+#define ALT_SGDMA_CONTROL_IE_MAX_DESC_PROCESSED_MSK (0x00000080)
+#define ALT_SGDMA_CONTROL_MAX_DESC_PROCESSED_MSK (0x0000FF00)
+#define ALT_SGDMA_CONTROL_SOFTWARERESET_MSK (0x00010000)
+#define ALT_SGDMA_CONTROL_PARK_MSK (0x00020000)
+#define ALT_SGDMA_CONTROL_CLEAR_INTERRUPT_MSK (0x80000000)
+
+#define ALTERA_TSE_SGDMA_INTR_MASK (ALT_SGDMA_CONTROL_IE_CHAIN_COMPLETED_MSK \
+ | ALT_SGDMA_STATUS_DESC_COMPLETED_MSK \
+ | ALT_SGDMA_CONTROL_IE_GLOBAL_MSK)
+
+/*
+ * Descriptor control bit masks & offsets
+ *
+ * Note: The control byte physically occupies bits [31:24] in memory.
+ * The following bit-offsets are expressed relative to the LSB of
+ * the control register bitfield.
+ */
+#define ALT_SGDMA_DESCRIPTOR_CONTROL_GENERATE_EOP_MSK (0x00000001)
+#define ALT_SGDMA_DESCRIPTOR_CONTROL_READ_FIXED_ADDRESS_MSK (0x00000002)
+#define ALT_SGDMA_DESCRIPTOR_CONTROL_WRITE_FIXED_ADDRESS_MSK (0x00000004)
+#define ALT_SGDMA_DESCRIPTOR_CONTROL_ATLANTIC_CHANNEL_MSK (0x00000008)
+#define ALT_SGDMA_DESCRIPTOR_CONTROL_OWNED_BY_HW_MSK (0x00000080)
+
+/*
+ * Descriptor status bit masks & offsets
+ *
+ * Note: The status byte physically occupies bits [23:16] in memory.
+ * The following bit-offsets are expressed relative to the LSB of
+ * the status register bitfield.
+ */
+#define ALT_SGDMA_DESCRIPTOR_STATUS_E_CRC_MSK (0x00000001)
+#define ALT_SGDMA_DESCRIPTOR_STATUS_E_PARITY_MSK (0x00000002)
+#define ALT_SGDMA_DESCRIPTOR_STATUS_E_OVERFLOW_MSK (0x00000004)
+#define ALT_SGDMA_DESCRIPTOR_STATUS_E_SYNC_MSK (0x00000008)
+#define ALT_SGDMA_DESCRIPTOR_STATUS_E_UEOP_MSK (0x00000010)
+#define ALT_SGDMA_DESCRIPTOR_STATUS_E_MEOP_MSK (0x00000020)
+#define ALT_SGDMA_DESCRIPTOR_STATUS_E_MSOP_MSK (0x00000040)
+#define ALT_SGDMA_DESCRIPTOR_STATUS_TERMINATED_BY_EOP_MSK (0x00000080)
+#define ALT_SGDMA_DESCRIPTOR_STATUS_ERROR_MSK (0x0000007F)
+
+/*
+ * The SGDMA controller buffer descriptor allocates
+ * 64 bits for each address. To support ANSI C, the
+ * struct implementing a descriptor places 32-bits
+ * of padding directly above each address; each pad must
+ * be cleared when initializing a descriptor.
+ */
+
+/*
+ * Buffer Descriptor data structure
+ *
+ */
+struct alt_sgdma_descriptor {
+ unsigned int *source; /* the address of data to be read. */
+ unsigned int source_pad;
+
+ unsigned int *destination; /* the address to write data */
+ unsigned int destination_pad;
+
+ unsigned int *next; /* the next descriptor in the list. */
+ unsigned int next_pad;
+
+ unsigned short bytes_to_transfer; /* the number of bytes to transfer */
+ unsigned char read_burst;
+ unsigned char write_burst;
+
+ unsigned short actual_bytes_transferred;/* bytes transferred by DMA */
+ unsigned char descriptor_status;
+ unsigned char descriptor_control;
+
+} __packed_1_;
+
+/* SG-DMA Control/Status Slave registers map */
+
+struct alt_sgdma_registers {
+ unsigned int status;
+ unsigned int status_pad[3];
+ unsigned int control;
+ unsigned int control_pad[3];
+ unsigned int next_descriptor_pointer;
+ unsigned int descriptor_pad[3];
+};
+
+/* TSE Stuff */
+#define ALTERA_TSE_CMD_TX_ENA_MSK (0x00000001)
+#define ALTERA_TSE_CMD_RX_ENA_MSK (0x00000002)
+#define ALTERA_TSE_CMD_XON_GEN_MSK (0x00000004)
+#define ALTERA_TSE_CMD_ETH_SPEED_MSK (0x00000008)
+#define ALTERA_TSE_CMD_PROMIS_EN_MSK (0x00000010)
+#define ALTERA_TSE_CMD_PAD_EN_MSK (0x00000020)
+#define ALTERA_TSE_CMD_CRC_FWD_MSK (0x00000040)
+#define ALTERA_TSE_CMD_PAUSE_FWD_MSK (0x00000080)
+#define ALTERA_TSE_CMD_PAUSE_IGNORE_MSK (0x00000100)
+#define ALTERA_TSE_CMD_TX_ADDR_INS_MSK (0x00000200)
+#define ALTERA_TSE_CMD_HD_ENA_MSK (0x00000400)
+#define ALTERA_TSE_CMD_EXCESS_COL_MSK (0x00000800)
+#define ALTERA_TSE_CMD_LATE_COL_MSK (0x00001000)
+#define ALTERA_TSE_CMD_SW_RESET_MSK (0x00002000)
+#define ALTERA_TSE_CMD_MHASH_SEL_MSK (0x00004000)
+#define ALTERA_TSE_CMD_LOOPBACK_MSK (0x00008000)
+/* Bits (18:16) = address select */
+#define ALTERA_TSE_CMD_TX_ADDR_SEL_MSK (0x00070000)
+#define ALTERA_TSE_CMD_MAGIC_ENA_MSK (0x00080000)
+#define ALTERA_TSE_CMD_SLEEP_MSK (0x00100000)
+#define ALTERA_TSE_CMD_WAKEUP_MSK (0x00200000)
+#define ALTERA_TSE_CMD_XOFF_GEN_MSK (0x00400000)
+#define ALTERA_TSE_CMD_CNTL_FRM_ENA_MSK (0x00800000)
+#define ALTERA_TSE_CMD_NO_LENGTH_CHECK_MSK (0x01000000)
+#define ALTERA_TSE_CMD_ENA_10_MSK (0x02000000)
+#define ALTERA_TSE_CMD_RX_ERR_DISC_MSK (0x04000000)
+/* Bits (30..27) reserved */
+#define ALTERA_TSE_CMD_CNT_RESET_MSK (0x80000000)
+
+#define ALTERA_TSE_TX_CMD_STAT_TX_SHIFT16 (0x00040000)
+#define ALTERA_TSE_TX_CMD_STAT_OMIT_CRC (0x00020000)
+
+#define ALTERA_TSE_RX_CMD_STAT_RX_SHIFT16 (0x02000000)
+
+#define ALT_TSE_SW_RESET_WATCHDOG_CNTR 10000
+#define ALT_TSE_SGDMA_BUSY_WATCHDOG_CNTR 90000000
+
+/* Command_Config Register Bit Definitions */
+
+typedef volatile union __alt_tse_command_config {
+ unsigned int image;
+ struct {
+ unsigned int
+ transmit_enable:1, /* bit 0 */
+ receive_enable:1, /* bit 1 */
+ pause_frame_xon_gen:1, /* bit 2 */
+ ethernet_speed:1, /* bit 3 */
+ promiscuous_enable:1, /* bit 4 */
+ pad_enable:1, /* bit 5 */
+ crc_forward:1, /* bit 6 */
+ pause_frame_forward:1, /* bit 7 */
+ pause_frame_ignore:1, /* bit 8 */
+ set_mac_address_on_tx:1, /* bit 9 */
+ halfduplex_enable:1, /* bit 10 */
+ excessive_collision:1, /* bit 11 */
+ late_collision:1, /* bit 12 */
+ software_reset:1, /* bit 13 */
+ multicast_hash_mode_sel:1, /* bit 14 */
+ loopback_enable:1, /* bit 15 */
+ src_mac_addr_sel_on_tx:3, /* bit 18:16 */
+ magic_packet_detect:1, /* bit 19 */
+ sleep_mode_enable:1, /* bit 20 */
+ wake_up_request:1, /* bit 21 */
+ pause_frame_xoff_gen:1, /* bit 22 */
+ control_frame_enable:1, /* bit 23 */
+ payload_len_chk_disable:1, /* bit 24 */
+ enable_10mbps_intf:1, /* bit 25 */
+ rx_error_discard_enable:1, /* bit 26 */
+ reserved_bits:4, /* bit 30:27 */
+ self_clear_counter_reset:1; /* bit 31 */
+ } __packed_1_ bits;
+} __packed_1_ alt_tse_command_config;
+
+/* Tx_Cmd_Stat Register Bit Definitions */
+
+typedef volatile union __alt_tse_tx_cmd_stat {
+ unsigned int image;
+ struct {
+ unsigned int reserved_lsbs:17, /* bit 16:0 */
+ omit_crc:1, /* bit 17 */
+ tx_shift16:1, /* bit 18 */
+ reserved_msbs:13; /* bit 31:19 */
+
+ } __packed_1_ bits;
+} alt_tse_tx_cmd_stat;
+
+/* Rx_Cmd_Stat Register Bit Definitions */
+
+typedef volatile union __alt_tse_rx_cmd_stat {
+ unsigned int image;
+ struct {
+ unsigned int reserved_lsbs:25, /* bit 24:0 */
+ rx_shift16:1, /* bit 25 */
+ reserved_msbs:6; /* bit 31:26 */
+
+ } __packed_1_ bits;
+} alt_tse_rx_cmd_stat;
+
+struct alt_tse_mdio {
+ unsigned int control; /*PHY device operation control register */
+ unsigned int status; /*PHY device operation status register */
+ unsigned int phy_id1; /*Bits 31:16 of PHY identifier. */
+ unsigned int phy_id2; /*Bits 15:0 of PHY identifier. */
+ unsigned int auto_negotiation_advertisement;
+ unsigned int remote_partner_base_page_ability;
+
+ unsigned int reg6;
+ unsigned int reg7;
+ unsigned int reg8;
+ unsigned int reg9;
+ unsigned int rega;
+ unsigned int regb;
+ unsigned int regc;
+ unsigned int regd;
+ unsigned int rege;
+ unsigned int regf;
+ unsigned int reg10;
+ unsigned int reg11;
+ unsigned int reg12;
+ unsigned int reg13;
+ unsigned int reg14;
+ unsigned int reg15;
+ unsigned int reg16;
+ unsigned int reg17;
+ unsigned int reg18;
+ unsigned int reg19;
+ unsigned int reg1a;
+ unsigned int reg1b;
+ unsigned int reg1c;
+ unsigned int reg1d;
+ unsigned int reg1e;
+ unsigned int reg1f;
+};
+
+/* MAC register Space */
+
+struct alt_tse_mac {
+ unsigned int megacore_revision;
+ unsigned int scratch_pad;
+ alt_tse_command_config command_config;
+ unsigned int mac_addr_0;
+ unsigned int mac_addr_1;
+ unsigned int max_frame_length;
+ unsigned int pause_quanta;
+ unsigned int rx_sel_empty_threshold;
+ unsigned int rx_sel_full_threshold;
+ unsigned int tx_sel_empty_threshold;
+ unsigned int tx_sel_full_threshold;
+ unsigned int rx_almost_empty_threshold;
+ unsigned int rx_almost_full_threshold;
+ unsigned int tx_almost_empty_threshold;
+ unsigned int tx_almost_full_threshold;
+ unsigned int mdio_phy0_addr;
+ unsigned int mdio_phy1_addr;
+
+ /* only if 100/1000 BaseX PCS, reserved otherwise */
+ unsigned int reservedx44[5];
+
+ unsigned int reg_read_access_status;
+ unsigned int min_tx_ipg_length;
+
+ /* IEEE 802.3 oEntity Managed Object Support */
+ unsigned int aMACID_1; /*The MAC addresses */
+ unsigned int aMACID_2;
+ unsigned int aFramesTransmittedOK;
+ unsigned int aFramesReceivedOK;
+ unsigned int aFramesCheckSequenceErrors;
+ unsigned int aAlignmentErrors;
+ unsigned int aOctetsTransmittedOK;
+ unsigned int aOctetsReceivedOK;
+
+ /* IEEE 802.3 oPausedEntity Managed Object Support */
+ unsigned int aTxPAUSEMACCtrlFrames;
+ unsigned int aRxPAUSEMACCtrlFrames;
+
+ /* IETF MIB (MIB-II) Object Support */
+ unsigned int ifInErrors;
+ unsigned int ifOutErrors;
+ unsigned int ifInUcastPkts;
+ unsigned int ifInMulticastPkts;
+ unsigned int ifInBroadcastPkts;
+ unsigned int ifOutDiscards;
+ unsigned int ifOutUcastPkts;
+ unsigned int ifOutMulticastPkts;
+ unsigned int ifOutBroadcastPkts;
+
+ /* IETF RMON MIB Object Support */
+ unsigned int etherStatsDropEvent;
+ unsigned int etherStatsOctets;
+ unsigned int etherStatsPkts;
+ unsigned int etherStatsUndersizePkts;
+ unsigned int etherStatsOversizePkts;
+ unsigned int etherStatsPkts64Octets;
+ unsigned int etherStatsPkts65to127Octets;
+ unsigned int etherStatsPkts128to255Octets;
+ unsigned int etherStatsPkts256to511Octets;
+ unsigned int etherStatsPkts512to1023Octets;
+ unsigned int etherStatsPkts1024to1518Octets;
+
+ unsigned int etherStatsPkts1519toXOctets;
+ unsigned int etherStatsJabbers;
+ unsigned int etherStatsFragments;
+
+ unsigned int reservedxE4;
+
+ /*FIFO control register. */
+ alt_tse_tx_cmd_stat tx_cmd_stat;
+ alt_tse_rx_cmd_stat rx_cmd_stat;
+
+ unsigned int ipaccTxConf;
+ unsigned int ipaccRxConf;
+ unsigned int ipaccRxStat;
+ unsigned int ipaccRxStatSum;
+
+ /*Multicast address resolution table */
+ unsigned int hash_table[64];
+
+ /*Registers 0 to 31 within PHY device 0/1 */
+ struct alt_tse_mdio mdio_phy0;
+ struct alt_tse_mdio mdio_phy1;
+
+ /*4 Supplemental MAC Addresses */
+ unsigned int supp_mac_addr_0_0;
+ unsigned int supp_mac_addr_0_1;
+ unsigned int supp_mac_addr_1_0;
+ unsigned int supp_mac_addr_1_1;
+ unsigned int supp_mac_addr_2_0;
+ unsigned int supp_mac_addr_2_1;
+ unsigned int supp_mac_addr_3_0;
+ unsigned int supp_mac_addr_3_1;
+
+ unsigned int reservedx320[56];
+};
+
+/* flags: TSE MII modes */
+/* GMII/MII = 0 */
+/* RGMII = 1 */
+/* RGMII_ID = 2 */
+/* RGMII_TXID = 3 */
+/* RGMII_RXID = 4 */
+/* SGMII = 5 */
+struct altera_tse_priv {
+ char devname[16];
+ volatile struct alt_tse_mac *mac_dev;
+ volatile struct alt_sgdma_registers *sgdma_rx;
+ volatile struct alt_sgdma_registers *sgdma_tx;
+ unsigned int rx_sgdma_irq;
+ unsigned int tx_sgdma_irq;
+ unsigned int has_descriptor_mem;
+ unsigned int descriptor_mem_base;
+ unsigned int descriptor_mem_size;
+ volatile struct alt_sgdma_descriptor *rx_desc;
+ volatile struct alt_sgdma_descriptor *tx_desc;
+ volatile unsigned char *rx_buf;
+ struct phy_info *phyinfo;
+ unsigned int phyaddr;
+ unsigned int flags;
+ unsigned int link;
+ unsigned int duplexity;
+ unsigned int speed;
+};
+
+/* Phy stuff continued */
+/*
+ * struct phy_cmd: A command for reading or writing a PHY register
+ *
+ * mii_reg: The register to read or write
+ *
+ * mii_data: For writes, the value to put in the register.
+ * A value of -1 indicates this is a read.
+ *
+ * funct: A function pointer which is invoked for each command.
+ * For reads, this function will be passed the value read
+ * from the PHY, and process it.
+ * For writes, the result of this function will be written
+ * to the PHY register
+ */
+struct phy_cmd {
+ uint mii_reg;
+ uint mii_data;
+ uint(*funct) (uint mii_reg, struct altera_tse_priv *priv);
+};
+#endif /* _ALTERA_TSE_H_ */