usb: storage: Use the correct CBW lengths
USB UFI uses fixed 12-byte commands (as does RBC, which is not
supported), but SCSI does not have this limitation. Use the correct
command block lengths depending on the subclass.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Marek Vasut <marex@denx.de>
diff --git a/common/usb_storage.c b/common/usb_storage.c
index 35c656d..774d5bd 100644
--- a/common/usb_storage.c
+++ b/common/usb_storage.c
@@ -102,6 +102,7 @@
trans_reset transport_reset; /* reset routine */
trans_cmnd transport; /* transport routine */
unsigned short max_xfer_blk; /* maximum transfer blocks */
+ bool cmd12; /* use 12-byte commands (RBC/UFI) */
};
#if !CONFIG_IS_ENABLED(BLK)
@@ -359,7 +360,7 @@
{
int i;
printf("SRB: len %d datalen 0x%lX\n ", pccb->cmdlen, pccb->datalen);
- for (i = 0; i < 12; i++)
+ for (i = 0; i < pccb->cmdlen; i++)
printf("%02X ", pccb->cmd[i]);
printf("\n");
}
@@ -898,7 +899,7 @@
psrb->cmd[4] = 18;
psrb->datalen = 18;
psrb->pdata = &srb->sense_buf[0];
- psrb->cmdlen = 12;
+ psrb->cmdlen = us->cmd12 ? 12 : 6;
/* issue the command */
result = usb_stor_CB_comdat(psrb, us);
debug("auto request returned %d\n", result);
@@ -999,7 +1000,7 @@
srb->cmd[1] = srb->lun << 5;
srb->cmd[4] = 36;
srb->datalen = 36;
- srb->cmdlen = 12;
+ srb->cmdlen = ss->cmd12 ? 12 : 6;
i = ss->transport(srb, ss);
debug("inquiry returns %d\n", i);
if (i == 0)
@@ -1024,7 +1025,7 @@
srb->cmd[4] = 18;
srb->datalen = 18;
srb->pdata = &srb->sense_buf[0];
- srb->cmdlen = 12;
+ srb->cmdlen = ss->cmd12 ? 12 : 6;
ss->transport(srb, ss);
debug("Request Sense returned %02X %02X %02X\n",
srb->sense_buf[2], srb->sense_buf[12],
@@ -1042,7 +1043,7 @@
srb->cmd[0] = SCSI_TST_U_RDY;
srb->cmd[1] = srb->lun << 5;
srb->datalen = 0;
- srb->cmdlen = 12;
+ srb->cmdlen = ss->cmd12 ? 12 : 6;
if (ss->transport(srb, ss) == USB_STOR_TRANSPORT_GOOD) {
ss->flags |= USB_READY;
return 0;
@@ -1074,7 +1075,7 @@
srb->cmd[0] = SCSI_RD_CAPAC;
srb->cmd[1] = srb->lun << 5;
srb->datalen = 8;
- srb->cmdlen = 12;
+ srb->cmdlen = ss->cmd12 ? 12 : 10;
if (ss->transport(srb, ss) == USB_STOR_TRANSPORT_GOOD)
return 0;
} while (retry--);
@@ -1094,7 +1095,7 @@
srb->cmd[5] = ((unsigned char) (start)) & 0xff;
srb->cmd[7] = ((unsigned char) (blocks >> 8)) & 0xff;
srb->cmd[8] = (unsigned char) blocks & 0xff;
- srb->cmdlen = 12;
+ srb->cmdlen = ss->cmd12 ? 12 : 10;
debug("read10: start %lx blocks %x\n", start, blocks);
return ss->transport(srb, ss);
}
@@ -1111,7 +1112,7 @@
srb->cmd[5] = ((unsigned char) (start)) & 0xff;
srb->cmd[7] = ((unsigned char) (blocks >> 8)) & 0xff;
srb->cmd[8] = (unsigned char) blocks & 0xff;
- srb->cmdlen = 12;
+ srb->cmdlen = ss->cmd12 ? 12 : 10;
debug("write10: start %lx blocks %x\n", start, blocks);
return ss->transport(srb, ss);
}
@@ -1417,6 +1418,11 @@
printf("Sorry, protocol %d not yet supported.\n", ss->subclass);
return 0;
}
+
+ /* UFI uses 12-byte commands (like RBC, unlike SCSI) */
+ if (ss->subclass == US_SC_UFI)
+ ss->cmd12 = true;
+
if (ss->ep_int) {
/* we had found an interrupt endpoint, prepare irq pipe
* set up the IRQ pipe and handler