doc: move test/py/README.md to HTML documentation
Convert test/py/README.md to restructured text and add it to the generated
HTML documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
diff --git a/doc/develop/py_testing.rst b/doc/develop/py_testing.rst
new file mode 100644
index 0000000..f71e837
--- /dev/null
+++ b/doc/develop/py_testing.rst
@@ -0,0 +1,426 @@
+U-Boot pytest suite
+===================
+
+Introduction
+------------
+
+This tool aims to test U-Boot by executing U-Boot shell commands using the
+console interface. A single top-level script exists to execute or attach to the
+U-Boot console, run the entire script of tests against it, and summarize the
+results. Advantages of this approach are:
+
+- Testing is performed in the same way a user or script would interact with
+ U-Boot; there can be no disconnect.
+- There is no need to write or embed test-related code into U-Boot itself.
+ It is asserted that writing test-related code in Python is simpler and more
+ flexible than writing it all in C.
+- It is reasonably simple to interact with U-Boot in this way.
+
+Requirements
+------------
+
+The test suite is implemented using pytest. Interaction with the U-Boot console
+involves executing some binary and interacting with its stdin/stdout. You will
+need to implement various "hook" scripts that are called by the test suite at
+the appropriate time.
+
+In order to run the test suite at a minimum we require that both Python 3 and
+pip for Python 3 are installed. All of the required python modules are
+described in the requirements.txt file in the /test/py/ directory and can be
+installed via the command
+
+.. code-block:: bash
+
+ pip install -r requirements.txt
+
+In order to execute certain tests on their supported platforms other tools
+will be required. The following is an incomplete list:
+
+* gdisk
+* dfu-util
+* dtc
+* openssl
+* sudo OR guestmount
+* e2fsprogs
+* util-linux
+* coreutils
+* dosfstools
+* efitools
+* mount
+* mtools
+* sbsigntool
+* udisks2
+
+Please use the appropriate commands for your distribution to match these tools
+up with the package that provides them.
+
+The test script supports either:
+
+- Executing a sandbox port of U-Boot on the local machine as a sub-process,
+ and interacting with it over stdin/stdout.
+- Executing an external "hook" scripts to flash a U-Boot binary onto a
+ physical board, attach to the board's console stream, and reset the board.
+ Further details are described later.
+
+Using `virtualenv` to provide requirements
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The recommended way to run the test suite, in order to ensure reproducibility
+is to use `virtualenv` to set up the necessary environment. This can be done
+via the following commands:
+
+
+.. code-block:: console
+
+ $ cd /path/to/u-boot
+ $ sudo apt-get install python3 python3-virtualenv
+ $ virtualenv -p /usr/bin/python3 venv
+ $ . ./venv/bin/activate
+ $ pip install -r test/py/requirements.txt
+
+Testing sandbox
+---------------
+
+To run the test suite on the sandbox port (U-Boot built as a native user-space
+application), simply execute:
+
+.. code-block:: bash
+
+ ./test/py/test.py --bd sandbox --build
+
+The `--bd` option tells the test suite which board type is being tested. This
+lets the test suite know which features the board has, and hence exactly what
+can be tested.
+
+The `--build` option tells U-Boot to compile U-Boot. Alternatively, you may
+omit this option and build U-Boot yourself, in whatever way you choose, before
+running the test script.
+
+The test script will attach to U-Boot, execute all valid tests for the board,
+then print a summary of the test process. A complete log of the test session
+will be written to `${build_dir}/test-log.html`. This is best viewed in a web
+browser, but may be read directly as plain text, perhaps with the aid of the
+`html2text` utility.
+
+Testing under a debugger
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+If you need to run sandbox under a debugger, you may pass the command-line
+option `--gdbserver COMM`. This causes two things to happens:
+
+- Instead of running U-Boot directly, it will be run under gdbserver, with
+ debug communication via the channel `COMM`. You can attach a debugger to the
+ sandbox process in order to debug it. See `man gdbserver` and the example
+ below for details of valid values for `COMM`.
+- All timeouts in tests are disabled, allowing U-Boot an arbitrary amount of
+ time to execute commands. This is useful if U-Boot is stopped at a breakpoint
+ during debugging.
+
+A usage example is:
+
+Window 1:
+
+.. code-block:: bash
+
+ ./test/py/test.py --bd sandbox --gdbserver localhost:1234
+
+Window 2:
+
+.. code-block:: bash
+
+ gdb ./build-sandbox/u-boot -ex 'target remote localhost:1234'
+
+Alternatively, you could leave off the `-ex` option and type the command
+manually into gdb once it starts.
+
+You can use any debugger you wish, as long as it speaks the gdb remote
+protocol, or any graphical wrapper around gdb.
+
+Some tests deliberately cause the sandbox process to exit, e.g. to test the
+reset command, or sandbox's CTRL-C handling. When this happens, you will need
+to attach the debugger to the new sandbox instance. If these tests are not
+relevant to your debugging session, you can skip them using pytest's -k
+command-line option; see the next section.
+
+Command-line options
+--------------------
+
+--board-type, --bd, -B
+ set the type of the board to be tested. For example, `sandbox` or `seaboard`.
+
+--board-identity`, --id
+ sets the identity of the board to be tested. This allows differentiation
+ between multiple instances of the same type of physical board that are
+ attached to the same host machine. This parameter is not interpreted by th
+ test script in any way, but rather is simply passed to the hook scripts
+ described below, and may be used in any site-specific way deemed necessary.
+
+--build
+ indicates that the test script should compile U-Boot itself before running
+ the tests. If using this option, make sure that any environment variables
+ required by the build process are already set, such as `$CROSS_COMPILE`.
+
+--buildman
+ indicates that `--build` should use buildman to build U-Boot. There is no need
+ to set $CROSS_COMPILE` in this case since buildman handles it.
+
+--build-dir
+ sets the directory containing the compiled U-Boot binaries. If omitted, this
+ is `${source_dir}/build-${board_type}`.
+
+--result-dir
+ sets the directory to write results, such as log files, into.
+ If omitted, the build directory is used.
+
+--persistent-data-dir
+ sets the directory used to store persistent test data. This is test data that
+ may be re-used across test runs, such as file-system images.
+
+`pytest` also implements a number of its own command-line options. Commonly used
+options are mentioned below. Please see `pytest` documentation for complete
+details. Execute `py.test --version` for a brief summary. Note that U-Boot's
+test.py script passes all command-line arguments directly to `pytest` for
+processing.
+
+-k
+ selects which tests to run. The default is to run all known tests. This
+ option takes a single argument which is used to filter test names. Simple
+ logical operators are supported. For example:
+
+ - `'-k ums'` runs only tests with "ums" in their name.
+ - `'-k ut_dm'` runs only tests with "ut_dm" in their name. Note that in this
+ case, "ut_dm" is a parameter to a test rather than the test name. The full
+ test name is e.g. "test_ut[ut_dm_leak]".
+ - `'-k not reset'` runs everything except tests with "reset" in their name.
+ - `'-k ut or hush'` runs only tests with "ut" or "hush" in their name.
+ - `'-k not (ut or hush)'` runs everything except tests with "ut" or "hush" in
+ their name.
+
+-s
+ prevents pytest from hiding a test's stdout. This allows you to see
+ U-Boot's console log in real time on pytest's stdout.
+
+Testing real hardware
+---------------------
+
+The tools and techniques used to interact with real hardware will vary
+radically between different host and target systems, and the whims of the user.
+For this reason, the test suite does not attempt to directly interact with real
+hardware in any way. Rather, it executes a standardized set of "hook" scripts
+via `$PATH`. These scripts implement certain actions on behalf of the test
+suite. This keeps the test suite simple and isolated from system variances
+unrelated to U-Boot features.
+
+Hook scripts
+~~~~~~~~~~~~
+
+Environment variables
+'''''''''''''''''''''
+
+The following environment variables are set when running hook scripts:
+
+- `UBOOT_BOARD_TYPE` the board type being tested.
+- `UBOOT_BOARD_IDENTITY` the board identity being tested, or `na` if none was
+ specified.
+- `UBOOT_SOURCE_DIR` the U-Boot source directory.
+- `UBOOT_TEST_PY_DIR` the full path to `test/py/` in the source directory.
+- `UBOOT_BUILD_DIR` the U-Boot build directory.
+- `UBOOT_RESULT_DIR` the test result directory.
+- `UBOOT_PERSISTENT_DATA_DIR` the test persistent data directory.
+
+u-boot-test-console
+'''''''''''''''''''
+
+This script provides access to the U-Boot console. The script's stdin/stdout
+should be connected to the board's console. This process should continue to run
+indefinitely, until killed. The test suite will run this script in parallel
+with all other hooks.
+
+This script may be implemented e.g. by executing `cu`, `kermit`, `conmux`, etc.
+via exec().
+
+If you are able to run U-Boot under a hardware simulator such as QEMU, then
+you would likely spawn that simulator from this script. However, note that
+`u-boot-test-reset` may be called multiple times per test script run, and must
+cause U-Boot to start execution from scratch each time. Hopefully your
+simulator includes a virtual reset button! If not, you can launch the
+simulator from `u-boot-test-reset` instead, while arranging for this console
+process to always communicate with the current simulator instance.
+
+u-boot-test-flash
+'''''''''''''''''
+
+Prior to running the test suite against a board, some arrangement must be made
+so that the board executes the particular U-Boot binary to be tested. Often
+this involves writing the U-Boot binary to the board's flash ROM. The test
+suite calls this hook script for that purpose.
+
+This script should perform the entire flashing process synchronously; the
+script should only exit once flashing is complete, and a board reset will
+cause the newly flashed U-Boot binary to be executed.
+
+It is conceivable that this script will do nothing. This might be useful in
+the following cases:
+
+- Some other process has already written the desired U-Boot binary into the
+ board's flash prior to running the test suite.
+- The board allows U-Boot to be downloaded directly into RAM, and executed
+ from there. Use of this feature will reduce wear on the board's flash, so
+ may be preferable if available, and if cold boot testing of U-Boot is not
+ required. If this feature is used, the `u-boot-test-reset` script should
+ perform this download, since the board could conceivably be reset multiple
+ times in a single test run.
+
+It is up to the user to determine if those situations exist, and to code this
+hook script appropriately.
+
+This script will typically be implemented by calling out to some SoC- or
+board-specific vendor flashing utility.
+
+u-boot-test-reset
+'''''''''''''''''
+
+Whenever the test suite needs to reset the target board, this script is
+executed. This is guaranteed to happen at least once, prior to executing the
+first test function. If any test fails, the test infra-structure will execute
+this script again to restore U-Boot to an operational state before running the
+next test function.
+
+This script will likely be implemented by communicating with some form of
+relay or electronic switch attached to the board's reset signal.
+
+The semantics of this script require that when it is executed, U-Boot will
+start running from scratch. If the U-Boot binary to be tested has been written
+to flash, pulsing the board's reset signal is likely all this script needs to
+do. However, in some scenarios, this script may perform other actions. For
+example, it may call out to some SoC- or board-specific vendor utility in order
+to download the U-Boot binary directly into RAM and execute it. This would
+avoid the need for `u-boot-test-flash` to actually write U-Boot to flash, thus
+saving wear on the flash chip(s).
+
+Examples
+''''''''
+
+https://github.com/swarren/uboot-test-hooks contains some working example hook
+scripts, and may be useful as a reference when implementing hook scripts for
+your platform. These scripts are not considered part of U-Boot itself.
+
+Board-type-specific configuration
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Each board has a different configuration and behaviour. Many of these
+differences can be automatically detected by parsing the `.config` file in the
+build directory. However, some differences can't yet be handled automatically.
+
+For each board, an optional Python module `u_boot_board_${board_type}` may exist
+to provide board-specific information to the test script. Any global value
+defined in these modules is available for use by any test function. The data
+contained in these scripts must be purely derived from U-Boot source code.
+Hence, these configuration files are part of the U-Boot source tree too.
+
+Execution environment configuration
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Each user's hardware setup may enable testing different subsets of the features
+implemented by a particular board's configuration of U-Boot. For example, a
+U-Boot configuration may support USB device mode and USB Mass Storage, but this
+can only be tested if a USB cable is connected between the board and the host
+machine running the test script.
+
+For each board, optional Python modules `u_boot_boardenv_${board_type}` and
+`u_boot_boardenv_${board_type}_${board_identity}` may exist to provide
+board-specific and board-identity-specific information to the test script. Any
+global value defined in these modules is available for use by any test
+function. The data contained in these is specific to a particular user's
+hardware configuration. Hence, these configuration files are not part of the
+U-Boot source tree, and should be installed outside of the source tree. Users
+should set `$PYTHONPATH` prior to running the test script to allow these
+modules to be loaded.
+
+Board module parameter usage
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The test scripts rely on the following variables being defined by the board
+module:
+
+- none at present
+
+U-Boot `.config` feature usage
+~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+The test scripts rely on various U-Boot `.config` features, either directly in
+order to test those features, or indirectly in order to query information from
+the running U-Boot instance in order to test other features.
+
+One example is that testing of the `md` command requires knowledge of a RAM
+address to use for the test. This data is parsed from the output of the
+`bdinfo` command, and hence relies on CONFIG_CMD_BDI being enabled.
+
+For a complete list of dependencies, please search the test scripts for
+instances of:
+
+- `buildconfig.get(...`
+- `@pytest.mark.buildconfigspec(...`
+- `@pytest.mark.notbuildconfigspec(...`
+
+Complete invocation example
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+Assuming that you have installed the hook scripts into $HOME/ubtest/bin, and
+any required environment configuration Python modules into $HOME/ubtest/py,
+then you would likely invoke the test script as follows:
+
+If U-Boot has already been built:
+
+.. code-block:: bash
+
+ PATH=$HOME/ubtest/bin:$PATH \
+ PYTHONPATH=${HOME}/ubtest/py/${HOSTNAME}:${PYTHONPATH} \
+ ./test/py/test.py --bd seaboard
+
+If you want the test script to compile U-Boot for you too, then you likely
+need to set `$CROSS_COMPILE` to allow this, and invoke the test script as
+follows:
+
+.. code-block:: bash
+
+ CROSS_COMPILE=arm-none-eabi- \
+ PATH=$HOME/ubtest/bin:$PATH \
+ PYTHONPATH=${HOME}/ubtest/py/${HOSTNAME}:${PYTHONPATH} \
+ ./test/py/test.py --bd seaboard --build
+
+or, using buildman to handle it:
+
+.. code-block:: bash
+
+ PATH=$HOME/ubtest/bin:$PATH \
+ PYTHONPATH=${HOME}/ubtest/py/${HOSTNAME}:${PYTHONPATH} \
+ ./test/py/test.py --bd seaboard --build --buildman
+
+Writing tests
+-------------
+
+Please refer to the pytest documentation for details of writing pytest tests.
+Details specific to the U-Boot test suite are described below.
+
+A test fixture named `u_boot_console` should be used by each test function. This
+provides the means to interact with the U-Boot console, and retrieve board and
+environment configuration information.
+
+The function `u_boot_console.run_command()` executes a shell command on the
+U-Boot console, and returns all output from that command. This allows
+validation or interpretation of the command output. This function validates
+that certain strings are not seen on the U-Boot console. These include shell
+error messages and the U-Boot sign-on message (in order to detect unexpected
+board resets). See the source of `u_boot_console_base.py` for a complete list of
+"bad" strings. Some test scenarios are expected to trigger these strings. Use
+`u_boot_console.disable_check()` to temporarily disable checking for specific
+strings. See `test_unknown_cmd.py` for an example.
+
+Board- and board-environment configuration values may be accessed as sub-fields
+of the `u_boot_console.config` object, for example
+`u_boot_console.config.ram_base`.
+
+Build configuration values (from `.config`) may be accessed via the dictionary
+`u_boot_console.config.buildconfig`, with keys equal to the Kconfig variable
+names.