Merge git://git.denx.de/u-boot-marvell
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index a047552..63ec024 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1480,7 +1480,6 @@
source "board/freescale/ls1012afrdm/Kconfig"
source "board/freescale/mx35pdk/Kconfig"
source "board/freescale/s32v234evb/Kconfig"
-source "board/gdsys/a38x/Kconfig"
source "board/grinn/chiliboard/Kconfig"
source "board/gumstix/pepper/Kconfig"
source "board/h2200/Kconfig"
diff --git a/arch/arm/dts/armada-388-clearfog-u-boot.dtsi b/arch/arm/dts/armada-388-clearfog-u-boot.dtsi
new file mode 100644
index 0000000..f31691e
--- /dev/null
+++ b/arch/arm/dts/armada-388-clearfog-u-boot.dtsi
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+
+
+&spi1 {
+ u-boot,dm-spl;
+
+ spi-flash@0 {
+ u-boot,dm-spl;
+ };
+};
diff --git a/arch/arm/dts/armada-388-clearfog.dts b/arch/arm/dts/armada-388-clearfog.dts
index a0b566a..16a47d5 100644
--- a/arch/arm/dts/armada-388-clearfog.dts
+++ b/arch/arm/dts/armada-388-clearfog.dts
@@ -50,6 +50,7 @@
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
/ {
model = "SolidRun Clearfog A1";
@@ -70,11 +71,6 @@
stdout-path = "serial0:115200n8";
};
- memory {
- device_type = "memory";
- reg = <0x00000000 0x10000000>; /* 256 MB */
- };
-
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
@@ -84,211 +80,7 @@
};
soc {
- ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
- MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
- MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
- MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
-
internal-regs {
- ethernet@30000 {
- mac-address = [00 50 43 02 02 02];
- phy-mode = "sgmii";
- status = "okay";
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
-
- ethernet@34000 {
- mac-address = [00 50 43 02 02 03];
- managed = "in-band-status";
- phy-mode = "sgmii";
- status = "okay";
- };
-
- ethernet@70000 {
- mac-address = [00 50 43 02 02 01];
- pinctrl-0 = <&ge0_rgmii_pins>;
- pinctrl-names = "default";
- phy = <&phy_dedicated>;
- phy-mode = "rgmii-id";
- status = "okay";
- };
-
- i2c@11000 {
- /* Is there anything on this? */
- clock-frequency = <100000>;
- pinctrl-0 = <&i2c0_pins>;
- pinctrl-names = "default";
- status = "okay";
-
- /*
- * PCA9655 GPIO expander, up to 1MHz clock.
- * 0-CON3 CLKREQ#
- * 1-CON3 PERST#
- * 2-CON2 PERST#
- * 3-CON3 W_DISABLE
- * 4-CON2 CLKREQ#
- * 5-USB3 overcurrent
- * 6-USB3 power
- * 7-CON2 W_DISABLE
- * 8-JP4 P1
- * 9-JP4 P4
- * 10-JP4 P5
- * 11-m.2 DEVSLP
- * 12-SFP_LOS
- * 13-SFP_TX_FAULT
- * 14-SFP_TX_DISABLE
- * 15-SFP_MOD_DEF0
- */
- expander0: gpio-expander@20 {
- /*
- * This is how it should be:
- * compatible = "onnn,pca9655",
- * "nxp,pca9555";
- * but you can't do this because of
- * the way I2C works.
- */
- compatible = "nxp,pca9555";
- gpio-controller;
- #gpio-cells = <2>;
- reg = <0x20>;
-
- pcie1_0_clkreq {
- gpio-hog;
- gpios = <0 GPIO_ACTIVE_LOW>;
- input;
- line-name = "pcie1.0-clkreq";
- };
- pcie1_0_w_disable {
- gpio-hog;
- gpios = <3 GPIO_ACTIVE_LOW>;
- output-low;
- line-name = "pcie1.0-w-disable";
- };
- pcie2_0_clkreq {
- gpio-hog;
- gpios = <4 GPIO_ACTIVE_LOW>;
- input;
- line-name = "pcie2.0-clkreq";
- };
- pcie2_0_w_disable {
- gpio-hog;
- gpios = <7 GPIO_ACTIVE_LOW>;
- output-low;
- line-name = "pcie2.0-w-disable";
- };
- usb3_ilimit {
- gpio-hog;
- gpios = <5 GPIO_ACTIVE_LOW>;
- input;
- line-name = "usb3-current-limit";
- };
- usb3_power {
- gpio-hog;
- gpios = <6 GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "usb3-power";
- };
- m2_devslp {
- gpio-hog;
- gpios = <11 GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "m.2 devslp";
- };
- };
-
- /* The MCP3021 is 100kHz clock only */
- mikrobus_adc: mcp3021@4c {
- compatible = "microchip,mcp3021";
- reg = <0x4c>;
- };
-
- /* Also something at 0x64 */
- };
-
- i2c@11100 {
- /*
- * Routed to SFP, mikrobus, and PCIe.
- * SFP limits this to 100kHz, and requires
- * an AT24C01A/02/04 with address pins tied
- * low, which takes addresses 0x50 and 0x51.
- * Mikrobus doesn't specify beyond an I2C
- * bus being present.
- * PCIe uses ARP to assign addresses, or
- * 0x63-0x64.
- */
- clock-frequency = <100000>;
- pinctrl-0 = <&clearfog_i2c1_pins>;
- pinctrl-names = "default";
- status = "okay";
- };
-
- mdio@72004 {
- pinctrl-0 = <&mdio_pins>;
- pinctrl-names = "default";
-
- phy_dedicated: ethernet-phy@0 {
- /*
- * Annoyingly, the marvell phy driver
- * configures the LED register, rather
- * than preserving reset-loaded setting.
- * We undo that rubbish here.
- */
- marvell,reg-init = <3 16 0 0x101e>;
- reg = <0>;
- };
- };
-
- pinctrl@18000 {
- clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins {
- marvell,pins = "mpp46";
- marvell,function = "ref";
- };
- clearfog_dsa0_pins: clearfog-dsa0-pins {
- marvell,pins = "mpp23", "mpp41";
- marvell,function = "gpio";
- };
- clearfog_i2c1_pins: i2c1-pins {
- /* SFP, PCIe, mSATA, mikrobus */
- marvell,pins = "mpp26", "mpp27";
- marvell,function = "i2c1";
- };
- clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins {
- marvell,pins = "mpp20";
- marvell,function = "gpio";
- };
- clearfog_sdhci_pins: clearfog-sdhci-pins {
- marvell,pins = "mpp21", "mpp28",
- "mpp37", "mpp38",
- "mpp39", "mpp40";
- marvell,function = "sd0";
- };
- clearfog_spi1_cs_pins: spi1-cs-pins {
- marvell,pins = "mpp55";
- marvell,function = "spi1";
- };
- mikro_pins: mikro-pins {
- /* int: mpp22 rst: mpp29 */
- marvell,pins = "mpp22", "mpp29";
- marvell,function = "gpio";
- };
- mikro_spi_pins: mikro-spi-pins {
- marvell,pins = "mpp43";
- marvell,function = "spi1";
- };
- mikro_uart_pins: mikro-uart-pins {
- marvell,pins = "mpp24", "mpp25";
- marvell,function = "ua1";
- };
- rear_button_pins: rear-button-pins {
- marvell,pins = "mpp34";
- marvell,function = "gpio";
- };
- };
-
rtc@a3800 {
/*
* If the rtc doesn't work, run "date reset"
@@ -311,7 +103,7 @@
bus-width = <4>;
cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
no-1-8-v;
- pinctrl-0 = <&clearfog_sdhci_pins
+ pinctrl-0 = <µsom_sdhci_pins
&clearfog_sdhci_cd_pins>;
pinctrl-names = "default";
status = "okay";
@@ -319,13 +111,6 @@
wp-inverted;
};
- serial@12000 {
- pinctrl-0 = <&uart0_pins>;
- pinctrl-names = "default";
- status = "okay";
- u-boot,dm-pre-reloc;
- };
-
serial@12100 {
/* mikrobus uart */
pinctrl-0 = <&mikro_uart_pins>;
@@ -342,17 +127,10 @@
pinctrl-0 = <&spi1_pins &clearfog_spi1_cs_pins &mikro_spi_pins>;
pinctrl-names = "default";
status = "okay";
-
- spi-flash@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "w25q32", "jedec,spi-nor", "spi-flash";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <3000000>;
- };
};
- usb3@f8000 {
+ usb0: usb3@f8000 {
+ /* CON7, USB-A port on back of device */
status = "okay";
};
};
@@ -376,72 +154,6 @@
};
};
- sfp: sfp {
- compatible = "sff,sfp";
- i2c-bus = <&i2c1>;
- los-gpio = <&expander0 12 GPIO_ACTIVE_HIGH>;
- moddef0-gpio = <&expander0 15 GPIO_ACTIVE_LOW>;
- sfp,ethernet = <ð2>;
- tx-disable-gpio = <&expander0 14 GPIO_ACTIVE_HIGH>;
- tx-fault-gpio = <&expander0 13 GPIO_ACTIVE_HIGH>;
- };
-
- dsa@0 {
- compatible = "marvell,dsa";
- dsa,ethernet = <ð1>;
- dsa,mii-bus = <&mdio>;
- pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
- pinctrl-names = "default";
- #address-cells = <2>;
- #size-cells = <0>;
-
- switch@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <4 0>;
-
- port@0 {
- reg = <0>;
- label = "lan1";
- };
-
- port@1 {
- reg = <1>;
- label = "lan2";
- };
-
- port@2 {
- reg = <2>;
- label = "lan3";
- };
-
- port@3 {
- reg = <3>;
- label = "lan4";
- };
-
- port@4 {
- reg = <4>;
- label = "lan5";
- };
-
- port@5 {
- reg = <5>;
- label = "cpu";
- };
-
- port@6 {
- /* 88E1512 external phy */
- reg = <6>;
- label = "lan6";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
- };
-
gpio-keys {
compatible = "gpio-keys";
pinctrl-0 = <&rear_button_pins>;
@@ -457,6 +169,159 @@
};
};
+&w25q32 {
+ status = "okay";
+};
+
+ð1 {
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ status = "okay";
+};
+
+ð2 {
+ phy-mode = "sgmii";
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ /*
+ * PCA9655 GPIO expander, up to 1MHz clock.
+ * 0-CON3 CLKREQ#
+ * 1-CON3 PERST#
+ * 2-CON2 PERST#
+ * 3-CON3 W_DISABLE
+ * 4-CON2 CLKREQ#
+ * 5-USB3 overcurrent
+ * 6-USB3 power
+ * 7-CON2 W_DISABLE
+ * 8-JP4 P1
+ * 9-JP4 P4
+ * 10-JP4 P5
+ * 11-m.2 DEVSLP
+ * 12-SFP_LOS
+ * 13-SFP_TX_FAULT
+ * 14-SFP_TX_DISABLE
+ * 15-SFP_MOD_DEF0
+ */
+ expander0: gpio-expander@20 {
+ /*
+ * This is how it should be:
+ * compatible = "onnn,pca9655",
+ * "nxp,pca9555";
+ * but you can't do this because of
+ * the way I2C works.
+ */
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+
+ pcie1_0_clkreq {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie1.0-clkreq";
+ };
+ pcie1_0_w_disable {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie1.0-w-disable";
+ };
+ pcie2_0_clkreq {
+ gpio-hog;
+ gpios = <4 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie2.0-clkreq";
+ };
+ pcie2_0_w_disable {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie2.0-w-disable";
+ };
+ usb3_ilimit {
+ gpio-hog;
+ gpios = <5 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "usb3-current-limit";
+ };
+ usb3_power {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb3-power";
+ };
+ m2_devslp {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "m.2 devslp";
+ };
+ };
+
+ mikrobus_adc: mcp3021@4c {
+ compatible = "microchip,mcp3021";
+ reg = <0x4c>;
+ };
+};
+
+&i2c1 {
+ /*
+ * Routed to SFP, mikrobus, and PCIe.
+ * SFP limits this to 100kHz, and requires
+ * an AT24C01A/02/04 with address pins tied
+ * low, which takes addresses 0x50 and 0x51.
+ * Mikrobus doesn't specify beyond an I2C
+ * bus being present.
+ * PCIe uses ARP to assign addresses, or
+ * 0x63-0x64.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&clearfog_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&pinctrl {
+ clearfog_i2c1_pins: i2c1-pins {
+ /* SFP, PCIe, mSATA, mikrobus */
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "i2c1";
+ };
+ clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+ clearfog_spi1_cs_pins: spi1-cs-pins {
+ marvell,pins = "mpp55";
+ marvell,function = "spi1";
+ };
+ mikro_pins: mikro-pins {
+ /* int: mpp22 rst: mpp29 */
+ marvell,pins = "mpp22", "mpp29";
+ marvell,function = "gpio";
+ };
+ mikro_spi_pins: mikro-spi-pins {
+ marvell,pins = "mpp43";
+ marvell,function = "spi1";
+ };
+ mikro_uart_pins: mikro-uart-pins {
+ marvell,pins = "mpp24", "mpp25";
+ marvell,function = "ua1";
+ };
+ rear_button_pins: rear-button-pins {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+};
+
/*
+#define A38x_CUSTOMER_BOARD_1_MPP16_23 0x00400011
MPP18: gpio ? (pca9655 int?)
diff --git a/arch/arm/dts/armada-388-helios4.dts b/arch/arm/dts/armada-388-helios4.dts
index 049d322..a154e0f 100644
--- a/arch/arm/dts/armada-388-helios4.dts
+++ b/arch/arm/dts/armada-388-helios4.dts
@@ -248,7 +248,7 @@
bus-width = <4>;
cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
no-1-8-v;
- pinctrl-0 = <&helios_sdhci_pins
+ pinctrl-0 = <µsom_sdhci_pins
&helios_sdhci_cd_pins>;
pinctrl-names = "default";
status = "okay";
@@ -286,12 +286,6 @@
marvell,pins = "mpp20";
marvell,function = "gpio";
};
- helios_sdhci_pins: helios-sdhci-pins {
- marvell,pins = "mpp21", "mpp28",
- "mpp37", "mpp38",
- "mpp39", "mpp40";
- marvell,function = "sd0";
- };
helios_led_pins: helios-led-pins {
marvell,pins = "mpp24", "mpp25",
"mpp49", "mpp50",
diff --git a/arch/arm/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi
index a262722..74f58de 100644
--- a/arch/arm/dts/armada-38x-solidrun-microsom.dtsi
+++ b/arch/arm/dts/armada-38x-solidrun-microsom.dtsi
@@ -86,7 +86,7 @@
w25q32: spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
- compatible = "w25q32", "jedec,spi-nor";
+ compatible = "w25q32", "jedec,spi-nor", "spi-flash";
reg = <0>; /* Chip select 0 */
spi-max-frequency = <3000000>;
status = "disabled";
diff --git a/arch/arm/dts/kirkwood-atl-sbx81lifxcat.dts b/arch/arm/dts/kirkwood-atl-sbx81lifxcat.dts
new file mode 100644
index 0000000..c234449
--- /dev/null
+++ b/arch/arm/dts/kirkwood-atl-sbx81lifxcat.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-98dx4122.dtsi"
+
+/ {
+ model = "Allied Telesis SBx81LIFXCAT Board";
+ compatible = "atl,SBx8LIFXCAT", "marvell,kirkwood-98DX4122",
+ "marvell,kirkwood";
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x08000000>; /* 128 MB */
+ };
+
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ aliases {
+ ethernet0 = ð0;
+ i2c0 = &i2c0;
+ spi0 = &spi0;
+ };
+
+ dsa {
+ compatible = "marvell,dsa";
+ #address-cells = <2>;
+ #size-cells = <0>;
+ dsa,ethernet = <ð0>;
+ dsa,mii-bus = <&mdio>;
+ status = "okay";
+
+ switch@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1 0>;
+
+ port@0 {
+ reg = <0>;
+ label = "internal0";
+ };
+ port@1 {
+ reg = <1>;
+ label = "internal1";
+ };
+ port@8 {
+ reg = <8>;
+ label = "internal8";
+ phy-mode = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ port@9 {
+ reg = <9>;
+ label = "internal9";
+ phy-mode = "rgmii-id";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ port@10 {
+ reg = <10>;
+ label = "cpu";
+ };
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ ledn {
+ label = "status:ledn";
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ };
+
+ ledp {
+ label = "status:ledp";
+ gpios = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p128", "jedec,spi-nor", "spi-flash";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ mode = <0>;
+
+ partition@u-boot {
+ reg = <0x00000000 0x00c00000>;
+ label = "u-boot";
+ };
+ partition@u-boot-env {
+ reg = <0x00c00000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition@unused {
+ reg = <0x00100000 0x00f00000>;
+ label = "unused";
+ };
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom@52 {
+ compatible = "atmel,24c04";
+ reg = <0x52>;
+ };
+
+ gpio3: gpio@76 {
+ #gpio-cells = <2>;
+ compatible = "nxp,pca9539";
+ reg = <0x76>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&mdio {
+ status = "okay";
+};
+
+ð0 {
+ status = "okay";
+
+ ethernet0-port@0 {
+ speed = <1000>;
+ duplex = <1>;
+ };
+};
diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index 5a5a63c..3b860c4 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -62,6 +62,9 @@
config TARGET_SBx81LIFKW
bool "Allied Telesis SBx81GS24/SBx81GT40/SBx81XS6/SBx81XS16"
+config TARGET_SBx81LIFXCAT
+ bool "Allied Telesis SBx81GP24/SBx81GT24"
+
endchoice
config SYS_SOC
@@ -85,5 +88,6 @@
source "board/Seagate/nas220/Kconfig"
source "board/zyxel/nsa310s/Kconfig"
source "board/alliedtelesis/SBx81LIFKW/Kconfig"
+source "board/alliedtelesis/SBx81LIFXCAT/Kconfig"
endif
diff --git a/board/gdsys/a38x/.gitignore b/arch/arm/mach-mvebu/.gitignore
similarity index 100%
rename from board/gdsys/a38x/.gitignore
rename to arch/arm/mach-mvebu/.gitignore
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 3df124c..d1f7133 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -148,6 +148,7 @@
default "ds414" if TARGET_DS414
default "maxbcm" if TARGET_MAXBCM
default "theadorable" if TARGET_THEADORABLE
+ default "a38x" if TARGET_CONTROLCENTERDC
config SYS_CONFIG_NAME
default "clearfog" if TARGET_CLEARFOG
@@ -163,6 +164,7 @@
default "theadorable" if TARGET_THEADORABLE
default "turris_omnia" if TARGET_TURRIS_OMNIA
default "turris_mox" if TARGET_TURRIS_MOX
+ default "controlcenterdc" if TARGET_CONTROLCENTERDC
config SYS_VENDOR
default "Marvell" if TARGET_DB_MV784MP_GP
@@ -176,24 +178,25 @@
default "Synology" if TARGET_DS414
default "CZ.NIC" if TARGET_TURRIS_OMNIA
default "CZ.NIC" if TARGET_TURRIS_MOX
+ default "gdsys" if TARGET_CONTROLCENTERDC
config SYS_SOC
default "mvebu"
-if TARGET_TURRIS_OMNIA
-
choice
- prompt "Turris Omnia boot method"
+ prompt "Boot method"
-config TURRIS_OMNIA_SPL_BOOT_DEVICE_SPI
+config MVEBU_SPL_BOOT_DEVICE_SPI
bool "SPI NOR flash"
-config TURRIS_OMNIA_SPL_BOOT_DEVICE_MMC
+config MVEBU_SPL_BOOT_DEVICE_MMC
bool "SDIO/MMC card"
+ select SPL_LIBDISK_SUPPORT
-endchoice
+config MVEBU_SPL_BOOT_DEVICE_UART
+ bool "UART"
-endif
+endchoice
config MVEBU_EFUSE
bool "Enable eFuse support"
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index ade7b87..ee2eca9 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -25,6 +25,39 @@
obj-$(CONFIG_ARMADA_38X) += ../../../drivers/ddr/marvell/a38x/xor.o
obj-$(CONFIG_ARMADA_XP) += ../../../drivers/ddr/marvell/axp/xor.o
obj-$(CONFIG_MVEBU_EFUSE) += efuse.o
+
+extra-y += kwbimage.cfg
+
+KWB_REPLACE += BOOT_FROM
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI),)
+ KWB_CFG_BOOT_FROM=spi
+endif
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC),)
+ KWB_CFG_BOOT_FROM=sdio
+endif
+ifneq ($(CONFIG_MVEBU_SPL_BOOT_DEVICE_UART),)
+ KWB_CFG_BOOT_FROM=uart
+endif
+
+ifneq ($(CONFIG_SECURED_MODE_IMAGE),)
+KWB_REPLACE += CSK_INDEX
+KWB_CFG_CSK_INDEX = $(CONFIG_SECURED_MODE_CSK_INDEX)
+
+KWB_REPLACE += SEC_BOOT_DEV
+KWB_CFG_SEC_BOOT_DEV=$(patsubst "%",%, \
+ $(if $(findstring BOOT_SPI_NOR_FLASH,$(CONFIG_SPL_BOOT_DEVICE)),0x34) \
+ $(if $(findstring BOOT_SDIO_MMC_CARD,$(CONFIG_SPL_BOOT_DEVICE)),0x31) \
+ )
+
+KWB_REPLACE += SEC_FUSE_DUMP
+KWB_CFG_SEC_FUSE_DUMP = a38x
+endif
+
+$(src)/kwbimage.cfg: $(src)/kwbimage.cfg.in include/autoconf.mk \
+ include/config/auto.conf
+ $(Q)sed -ne '$(foreach V,$(KWB_REPLACE),s/^#@$(V)/$(V) $(KWB_CFG_$(V))/;)p' \
+ <$< >$(dir $<)$(@F)
+
endif # CONFIG_SPL_BUILD
obj-y += gpio.o
obj-y += mbus.o
diff --git a/arch/arm/mach-mvebu/include/mach/config.h b/arch/arm/mach-mvebu/include/mach/config.h
index 2acfd33..9f51411 100644
--- a/arch/arm/mach-mvebu/include/mach/config.h
+++ b/arch/arm/mach-mvebu/include/mach/config.h
@@ -32,12 +32,12 @@
#endif
/*
- * By default kwbimage.cfg from board specific folder is used
+ * By default the generated mvebu kwbimage.cfg is used
* If for some board, different configuration file need to be used,
* CONFIG_SYS_KWD_CONFIG should be defined in board specific header file
*/
#ifndef CONFIG_SYS_KWD_CONFIG
-#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
+#define CONFIG_SYS_KWD_CONFIG arch/arm/mach-mvebu/kwbimage.cfg
#endif /* CONFIG_SYS_KWD_CONFIG */
/* Add target to build it automatically upon "make" */
diff --git a/board/gdsys/a38x/kwbimage.cfg.in b/arch/arm/mach-mvebu/kwbimage.cfg.in
similarity index 100%
rename from board/gdsys/a38x/kwbimage.cfg.in
rename to arch/arm/mach-mvebu/kwbimage.cfg.in
diff --git a/board/CZ.NIC/turris_omnia/kwbimage.cfg b/board/CZ.NIC/turris_omnia/kwbimage.cfg
deleted file mode 100644
index cc05792..0000000
--- a/board/CZ.NIC/turris_omnia/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2014 Stefan Roese <sr@denx.de>
-#
-
-# Armada XP uses version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM spi
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl.bin 0000005b 00000068
diff --git a/board/Marvell/db-88f6720/kwbimage.cfg b/board/Marvell/db-88f6720/kwbimage.cfg
deleted file mode 100644
index 1f748db..0000000
--- a/board/Marvell/db-88f6720/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2014 Stefan Roese <sr@denx.de>
-#
-
-# Armada XP uses version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM spi
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/board/Marvell/db-88f6820-amc/kwbimage.cfg b/board/Marvell/db-88f6820-amc/kwbimage.cfg
deleted file mode 100644
index 1f748db..0000000
--- a/board/Marvell/db-88f6820-amc/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2014 Stefan Roese <sr@denx.de>
-#
-
-# Armada XP uses version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM spi
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/board/Marvell/db-88f6820-gp/kwbimage.cfg b/board/Marvell/db-88f6820-gp/kwbimage.cfg
deleted file mode 100644
index 1f748db..0000000
--- a/board/Marvell/db-88f6820-gp/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2014 Stefan Roese <sr@denx.de>
-#
-
-# Armada XP uses version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM spi
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/board/Marvell/db-mv784mp-gp/kwbimage.cfg b/board/Marvell/db-mv784mp-gp/kwbimage.cfg
deleted file mode 100644
index 1f748db..0000000
--- a/board/Marvell/db-mv784mp-gp/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2014 Stefan Roese <sr@denx.de>
-#
-
-# Armada XP uses version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM spi
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/board/Synology/ds414/kwbimage.cfg b/board/Synology/ds414/kwbimage.cfg
deleted file mode 100644
index 1f748db..0000000
--- a/board/Synology/ds414/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2014 Stefan Roese <sr@denx.de>
-#
-
-# Armada XP uses version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM spi
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/board/alliedtelesis/SBx81LIFXCAT/Kconfig b/board/alliedtelesis/SBx81LIFXCAT/Kconfig
new file mode 100644
index 0000000..524c290
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFXCAT/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_SBx81LIFXCAT
+
+config SYS_BOARD
+ default "SBx81LIFXCAT"
+
+config SYS_VENDOR
+ default "alliedtelesis"
+
+config SYS_CONFIG_NAME
+ default "SBx81LIFXCAT"
+
+endif
diff --git a/board/alliedtelesis/SBx81LIFXCAT/MAINTAINERS b/board/alliedtelesis/SBx81LIFXCAT/MAINTAINERS
new file mode 100644
index 0000000..6b722de
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFXCAT/MAINTAINERS
@@ -0,0 +1,7 @@
+SBx81LIFXCAT BOARD
+M: Chris Packham <chris.packham@alliedtelesis.co.nz>
+S: Maintained
+F: board/alliedtelesis/SBx81LIFXCAT/
+F: include/configs/SBx81LIFXCAT
+F: configs/SBx81LIFXCAT_defconfig
+F: arch/arm/dts/kirkwood-atl-sbx81lifxcat.dts
diff --git a/board/alliedtelesis/SBx81LIFXCAT/Makefile b/board/alliedtelesis/SBx81LIFXCAT/Makefile
new file mode 100644
index 0000000..f21c8ef
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFXCAT/Makefile
@@ -0,0 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2010, 2018
+# Allied Telesis <www.alliedtelesis.com>
+#
+
+obj-y += sbx81lifxcat.o
diff --git a/board/alliedtelesis/SBx81LIFXCAT/kwbimage.cfg b/board/alliedtelesis/SBx81LIFXCAT/kwbimage.cfg
new file mode 100644
index 0000000..53d4812
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFXCAT/kwbimage.cfg
@@ -0,0 +1,49 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# (C) Copyright 2018 Allied Telesis
+#
+# Refer docs/README.kwimage for more details about how-to configure
+# and create kirkwood boot image
+#
+
+# Boot Media configurations
+BOOT_FROM spi # Boot from SPI flash
+
+# SOC registers configuration using bootrom header extension
+# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
+DATA 0xffd100e0 0x1b1b1b1b
+DATA 0xffd20134 0xffffffff
+DATA 0xffd20138 0x009fffff
+DATA 0xffd20154 0x00000000
+DATA 0xffd2014c 0x00000000
+DATA 0xffd20148 0x00000001
+
+# Dram initalization for 1 x x16
+# DDR II Micron part number MT47H64M16HR-3
+# MClk 333MHz, Size 128MB, ECC disable
+#
+DATA 0xffd01400 0x43000618
+DATA 0xffd01404 0x38543000
+DATA 0xffd01408 0x23125441
+DATA 0xffd0140c 0x00000832
+DATA 0xffd01410 0x0000000D
+DATA 0xffd01414 0x00000000
+DATA 0xffd01418 0x00000000
+DATA 0xffd0141c 0x00000652
+DATA 0xffd01420 0x00000042
+DATA 0xffd01424 0x0000F0FF
+DATA 0xffd01428 0x00074410
+DATA 0xffd0147C 0x00007441
+DATA 0xffd01500 0x00000000 # SDRAM CS[0] Base address at 0x00000000
+DATA 0xffd01504 0x07FFFFF1 # SDRAM CS[0] Size 128MiB
+DATA 0xffd01508 0x10000000
+DATA 0xffd0150c 0x00FFFFF4 # SDRAM CS[1] Size, window disabled
+DATA 0xffd01514 0x00FFFFF8 # SDRAM CS[2] Size, window disabled
+DATA 0xffd0151c 0x00FFFFFC # SDRAM CS[3] Size, window disabled
+DATA 0xffd01494 0x84210000
+DATA 0xffd01498 0x00000000
+DATA 0xffd0149c 0x0000F80F
+DATA 0xffd01480 0x00000001
+
+# End of Header extension
+DATA 0x0 0x0
diff --git a/board/alliedtelesis/SBx81LIFXCAT/sbx81lifxcat.c b/board/alliedtelesis/SBx81LIFXCAT/sbx81lifxcat.c
new file mode 100644
index 0000000..c584fc0
--- /dev/null
+++ b/board/alliedtelesis/SBx81LIFXCAT/sbx81lifxcat.c
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2010, 2018
+ * Allied Telesis <www.alliedtelesis.com>
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <led.h>
+#include <linux/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <asm/arch/mpp.h>
+#include <asm/arch/gpio.h>
+
+#define SBX81LIFXCAT_OE_LOW (~0)
+#define SBX81LIFXCAT_OE_HIGH (~BIT(11))
+#define SBX81LIFXCAT_OE_VAL_LOW (0)
+#define SBX81LIFXCAT_OE_VAL_HIGH (BIT(11))
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_early_init_f(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ mvebu_config_gpio(SBX81LIFXCAT_OE_VAL_LOW,
+ SBX81LIFXCAT_OE_VAL_HIGH,
+ SBX81LIFXCAT_OE_LOW, SBX81LIFXCAT_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ static const u32 kwmpp_config[] = {
+ MPP0_SPI_SCn,
+ MPP1_SPI_MOSI,
+ MPP2_SPI_SCK,
+ MPP3_SPI_MISO,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_TW_SDA,
+ MPP9_TW_SCK,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_GPO,
+ MPP13_UART1_TXD,
+ MPP14_UART1_RXD,
+ MPP15_GPIO,
+ MPP16_GPIO,
+ MPP17_GPIO,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GE1_0,
+ MPP21_GE1_1,
+ MPP22_GE1_2,
+ MPP23_GE1_3,
+ MPP24_GE1_4,
+ MPP25_GE1_5,
+ MPP26_GE1_6,
+ MPP27_GE1_7,
+ MPP28_GE1_8,
+ MPP29_GE1_9,
+ MPP30_GE1_10,
+ MPP31_GE1_11,
+ MPP32_GE1_12,
+ MPP33_GE1_13,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO,
+ MPP37_GPIO,
+ MPP38_GPIO,
+ MPP39_GPIO,
+ MPP40_GPIO,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+
+ kirkwood_mpp_conf(kwmpp_config, NULL);
+ return 0;
+}
+
+int board_init(void)
+{
+ /* address of boot parameters */
+ gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* automatically defined by kirkwood config.h */
+void reset_phy(void)
+{
+}
+#endif
+
+#ifdef CONFIG_MV88E61XX_SWITCH
+int mv88e61xx_hw_reset(struct phy_device *phydev)
+{
+ phydev->advertising = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full;
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_MISC_INIT_R
+int misc_init_r(void)
+{
+ struct udevice *dev;
+ int ret;
+
+ ret = led_get_by_label("status:ledp", &dev);
+ if (!ret)
+ led_set_state(dev, LEDST_ON);
+
+ ret = led_get_by_label("status:ledn", &dev);
+ if (!ret)
+ led_set_state(dev, LEDST_OFF);
+
+ return 0;
+}
+#endif
diff --git a/board/gdsys/a38x/Kconfig b/board/gdsys/a38x/Kconfig
deleted file mode 100644
index 3fdef64..0000000
--- a/board/gdsys/a38x/Kconfig
+++ /dev/null
@@ -1,36 +0,0 @@
-if TARGET_CONTROLCENTERDC
-
-config SYS_BOARD
- default "a38x"
-
-config SYS_VENDOR
- default "gdsys"
-
-config SYS_SOC
- default "mvebu"
-
-config SYS_CONFIG_NAME
- default "controlcenterdc"
-
-menu "Controlcenter DC board options"
-
-choice
- prompt "Select boot method"
-
-config SPL_BOOT_DEVICE_SPI
- bool "SPI"
-
-config SPL_BOOT_DEVICE_MMC
- bool "MMC"
- select SPL_LIBDISK_SUPPORT
-
-endchoice
-
-#config SPL_BOOT_DEVICE
-# int
-# default 1 if SPL_BOOT_DEVICE_SPI
-# default 2 if SPL_BOOT_DEVICE_MMC
-
-endmenu
-
-endif
diff --git a/board/gdsys/a38x/Makefile b/board/gdsys/a38x/Makefile
index 43fec2e..32fffab 100644
--- a/board/gdsys/a38x/Makefile
+++ b/board/gdsys/a38x/Makefile
@@ -7,36 +7,5 @@
obj-$(CONFIG_TARGET_CONTROLCENTERDC) += controlcenterdc.o hre.o spl.o keyprogram.o dt_helpers.o
ifeq ($(CONFIG_SPL_BUILD),)
-
obj-$(CONFIG_TARGET_CONTROLCENTERDC) += hydra.o ihs_phys.o
-
-extra-$(CONFIG_TARGET_CONTROLCENTERDC) += kwbimage.cfg
-
-KWB_REPLACE += BOOT_FROM
-ifneq ($(CONFIG_SPL_BOOT_DEVICE_SPI),)
- KWB_CFG_BOOT_FROM=spi
-endif
-ifneq ($(CONFIG_SPL_BOOT_DEVICE_MMC),)
- KWB_CFG_BOOT_FROM=sdio
-endif
-
-ifneq ($(CONFIG_SECURED_MODE_IMAGE),)
-KWB_REPLACE += CSK_INDEX
-KWB_CFG_CSK_INDEX = $(CONFIG_SECURED_MODE_CSK_INDEX)
-
-KWB_REPLACE += SEC_BOOT_DEV
-KWB_CFG_SEC_BOOT_DEV=$(patsubst "%",%, \
- $(if $(findstring BOOT_SPI_NOR_FLASH,$(CONFIG_SPL_BOOT_DEVICE)),0x34) \
- $(if $(findstring BOOT_SDIO_MMC_CARD,$(CONFIG_SPL_BOOT_DEVICE)),0x31) \
- )
-
-KWB_REPLACE += SEC_FUSE_DUMP
-KWB_CFG_SEC_FUSE_DUMP = a38x
-endif
-
-$(src)/kwbimage.cfg: $(src)/kwbimage.cfg.in include/autoconf.mk \
- include/config/auto.conf
- $(Q)sed -ne '$(foreach V,$(KWB_REPLACE),s/^#@$(V)/$(V) $(KWB_CFG_$(V))/;)p' \
- <$< >$(dir $<)$(@F)
-
endif
diff --git a/board/kobol/helios4/kwbimage.cfg b/board/kobol/helios4/kwbimage.cfg
deleted file mode 100644
index 035063b..0000000
--- a/board/kobol/helios4/kwbimage.cfg
+++ /dev/null
@@ -1,13 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# Copyright (C) 2015 Stefan Roese <sr@denx.de>
-#
-
-# Armada 38x use version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM sdio
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/board/maxbcm/kwbimage.cfg b/board/maxbcm/kwbimage.cfg
deleted file mode 100644
index 1f748db..0000000
--- a/board/maxbcm/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2014 Stefan Roese <sr@denx.de>
-#
-
-# Armada XP uses version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM spi
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/board/solidrun/clearfog/kwbimage.cfg b/board/solidrun/clearfog/kwbimage.cfg
deleted file mode 100644
index f41d25a..0000000
--- a/board/solidrun/clearfog/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2015 Stefan Roese <sr@denx.de>
-#
-
-# Armada 38x use version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM sdio
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/board/theadorable/kwbimage.cfg b/board/theadorable/kwbimage.cfg
deleted file mode 100644
index 4f3b7b2..0000000
--- a/board/theadorable/kwbimage.cfg
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
-#
-
-# Armada XP uses version 1 image format
-VERSION 1
-
-# Boot Media configurations
-BOOT_FROM spi
-
-# Binary Header (bin_hdr) with DDR3 training code
-BINARY spl/u-boot-spl-dtb.bin 0000005b 00000068
diff --git a/configs/SBx81LIFKW_defconfig b/configs/SBx81LIFKW_defconfig
index 348f861..c786120 100644
--- a/configs/SBx81LIFKW_defconfig
+++ b/configs/SBx81LIFKW_defconfig
@@ -35,5 +35,7 @@
CONFIG_MV88E61XX_CPU_PORT=10
CONFIG_MV88E61XX_PHY_PORTS=0x003
CONFIG_MV88E61XX_FIXED_PORTS=0x300
+CONFIG_DM_RTC=y
+CONFIG_RTC_MV=y
CONFIG_SPI=y
CONFIG_KIRKWOOD_SPI=y
diff --git a/configs/SBx81LIFXCAT_defconfig b/configs/SBx81LIFXCAT_defconfig
new file mode 100644
index 0000000..89921a5c
--- /dev/null
+++ b/configs/SBx81LIFXCAT_defconfig
@@ -0,0 +1,44 @@
+CONFIG_ARM=y
+CONFIG_KIRKWOOD=y
+CONFIG_SYS_TEXT_BASE=0x00600000
+CONFIG_TARGET_SBx81LIFXCAT=y
+CONFIG_IDENT_STRING="\nSBx81LIFXCAT"
+CONFIG_DEFAULT_DEVICE_TREE="kirkwood-atl-sbx81lifxcat"
+# CONFIG_SYS_MALLOC_F is not set
+CONFIG_BOOTDELAY=3
+CONFIG_SILENT_CONSOLE=y
+CONFIG_SILENT_U_BOOT_ONLY=y
+CONFIG_HUSH_PARSER=y
+# CONFIG_CMD_FLASH is not set
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_SF=y
+CONFIG_CMD_DHCP=y
+CONFIG_BOOTP_NTPSERVER=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_SNTP=y
+# CONFIG_CMD_LED is not set
+CONFIG_OF_CONTROL=y
+CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_DM=y
+CONFIG_DM_GPIO=y
+CONFIG_DM_PCA953X=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_I2C_MUX=y
+CONFIG_I2C_MUX_PCA954x=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+# CONFIG_MMC is not set
+CONFIG_SPI_FLASH=y
+CONFIG_SPI_FLASH_STMICRO=y
+# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
+CONFIG_PHYLIB=y
+CONFIG_MV88E61XX_SWITCH=y
+CONFIG_MV88E61XX_CPU_PORT=10
+CONFIG_MV88E61XX_PHY_PORTS=0x003
+CONFIG_MV88E61XX_FIXED_PORTS=0x300
+CONFIG_MV88E61XX_RGMII_DELAY=y
+CONFIG_SPI=y
+CONFIG_KIRKWOOD_SPI=y
diff --git a/configs/clearfog_defconfig b/configs/clearfog_defconfig
index 7a9ee51..2164e20 100644
--- a/configs/clearfog_defconfig
+++ b/configs/clearfog_defconfig
@@ -6,12 +6,12 @@
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_CLEARFOG=y
+CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC=y
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL=y
CONFIG_DEBUG_UART_BASE=0xd0012000
CONFIG_DEBUG_UART_CLOCK=250000000
-CONFIG_SPL_LIBDISK_SUPPORT=y
CONFIG_DEFAULT_DEVICE_TREE="armada-388-clearfog"
CONFIG_DEBUG_UART=y
CONFIG_DISTRO_DEFAULTS=y
diff --git a/configs/dns325_defconfig b/configs/dns325_defconfig
index f0ed209..d77f776 100644
--- a/configs/dns325_defconfig
+++ b/configs/dns325_defconfig
@@ -4,6 +4,7 @@
CONFIG_TARGET_DNS325=y
CONFIG_IDENT_STRING="\nD-Link DNS-325"
CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dns325"
+# CONFIG_SYS_MALLOC_F is not set
CONFIG_BOOTDELAY=3
CONFIG_CONSOLE_MUX=y
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -16,7 +17,6 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_FAT=y
CONFIG_CMD_JFFS2=y
@@ -26,10 +26,13 @@
CONFIG_ISO_PARTITION=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_MV=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/dreamplug_defconfig b/configs/dreamplug_defconfig
index 8090c9a..d7428ae 100644
--- a/configs/dreamplug_defconfig
+++ b/configs/dreamplug_defconfig
@@ -4,6 +4,7 @@
CONFIG_TARGET_DREAMPLUG=y
CONFIG_IDENT_STRING="\nMarvell-DreamPlug"
CONFIG_DEFAULT_DEVICE_TREE="kirkwood-dreamplug"
+# CONFIG_SYS_MALLOC_F is not set
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
@@ -15,19 +16,21 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
CONFIG_ISO_PARTITION=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_MV=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_KIRKWOOD_SPI=y
diff --git a/configs/ds109_defconfig b/configs/ds109_defconfig
index c920743..6428614 100644
--- a/configs/ds109_defconfig
+++ b/configs/ds109_defconfig
@@ -3,6 +3,7 @@
CONFIG_SYS_TEXT_BASE=0x600000
CONFIG_TARGET_DS109=y
CONFIG_DEFAULT_DEVICE_TREE="kirkwood-ds109"
+# CONFIG_SYS_MALLOC_F is not set
CONFIG_HUSH_PARSER=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_IDE=y
@@ -12,18 +13,22 @@
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_FAT=y
CONFIG_ISO_PARTITION=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
# CONFIG_MMC is not set
CONFIG_SPI_FLASH=y
CONFIG_SPI_FLASH_BAR=y
CONFIG_SPI_FLASH_STMICRO=y
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_MV=y
CONFIG_SYS_NS16550=y
CONFIG_SPI=y
CONFIG_KIRKWOOD_SPI=y
diff --git a/configs/goflexhome_defconfig b/configs/goflexhome_defconfig
index c0894c0..41d896a 100644
--- a/configs/goflexhome_defconfig
+++ b/configs/goflexhome_defconfig
@@ -4,6 +4,7 @@
CONFIG_TARGET_GOFLEXHOME=y
CONFIG_IDENT_STRING="\nSeagate GoFlex Home"
CONFIG_DEFAULT_DEVICE_TREE="kirkwood-goflexnet"
+# CONFIG_SYS_MALLOC_F is not set
CONFIG_BOOTDELAY=3
CONFIG_CONSOLE_MUX=y
# CONFIG_DISPLAY_BOARDINFO is not set
@@ -16,7 +17,6 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
@@ -27,10 +27,13 @@
CONFIG_ISO_PARTITION=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_MV=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/guruplug_defconfig b/configs/guruplug_defconfig
index da3895d..d77922e 100644
--- a/configs/guruplug_defconfig
+++ b/configs/guruplug_defconfig
@@ -4,6 +4,7 @@
CONFIG_TARGET_GURUPLUG=y
CONFIG_IDENT_STRING="\nMarvell-GuruPlug"
CONFIG_DEFAULT_DEVICE_TREE="kirkwood-guruplug-server-plus"
+# CONFIG_SYS_MALLOC_F is not set
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
@@ -16,7 +17,6 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
@@ -27,10 +27,13 @@
CONFIG_ISO_PARTITION=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_MV=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/helios4_defconfig b/configs/helios4_defconfig
index 441b375..f1eddaf 100644
--- a/configs/helios4_defconfig
+++ b/configs/helios4_defconfig
@@ -5,6 +5,7 @@
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_SYS_MALLOC_F_LEN=0x2000
CONFIG_TARGET_HELIOS4=y
+CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC=y
CONFIG_SPL_MMC_SUPPORT=y
CONFIG_SPL_SERIAL_SUPPORT=y
CONFIG_SPL=y
diff --git a/configs/nas220_defconfig b/configs/nas220_defconfig
index ddf5689..4ae69fe 100644
--- a/configs/nas220_defconfig
+++ b/configs/nas220_defconfig
@@ -4,6 +4,7 @@
CONFIG_TARGET_NAS220=y
CONFIG_IDENT_STRING="\nNAS 220"
CONFIG_DEFAULT_DEVICE_TREE="kirkwood-blackarmor-nas220"
+# CONFIG_SYS_MALLOC_F is not set
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
@@ -16,7 +17,6 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
@@ -27,10 +27,13 @@
# CONFIG_PARTITION_UUIDS is not set
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
# CONFIG_MMC is not set
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_MV=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
diff --git a/configs/sheevaplug_defconfig b/configs/sheevaplug_defconfig
index d27698f..b965ff4 100644
--- a/configs/sheevaplug_defconfig
+++ b/configs/sheevaplug_defconfig
@@ -5,6 +5,7 @@
CONFIG_TARGET_SHEEVAPLUG=y
CONFIG_IDENT_STRING="\nMarvell-Sheevaplug"
CONFIG_DEFAULT_DEVICE_TREE="kirkwood-sheevaplug"
+# CONFIG_SYS_MALLOC_F is not set
CONFIG_BOOTDELAY=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_HUSH_PARSER=y
@@ -18,7 +19,6 @@
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
-CONFIG_CMD_DATE=y
CONFIG_CMD_EXT2=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
@@ -29,9 +29,12 @@
CONFIG_ISO_PARTITION=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_IS_IN_NAND=y
+CONFIG_DM=y
CONFIG_MVSATA_IDE=y
CONFIG_NETDEVICES=y
CONFIG_MVGBE=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_MV=y
CONFIG_SYS_NS16550=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
diff --git a/include/configs/SBx81LIFKW.h b/include/configs/SBx81LIFKW.h
index bcc2c20..2471266 100644
--- a/include/configs/SBx81LIFKW.h
+++ b/include/configs/SBx81LIFKW.h
@@ -109,11 +109,6 @@
#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
#endif /* CONFIG_CMD_NET */
-/*
- * Time settings
- */
-#define CONFIG_RTC_MV
-
#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
#endif /* _CONFIG_SBX81LIFKW_H */
diff --git a/include/configs/SBx81LIFXCAT.h b/include/configs/SBx81LIFXCAT.h
new file mode 100644
index 0000000..0491832
--- /dev/null
+++ b/include/configs/SBx81LIFXCAT.h
@@ -0,0 +1,114 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * (C) Copyright 2016 Allied Telesis <www.alliedtelesis.co.nz>
+ */
+
+#ifndef _CONFIG_SBX81LIFXCAT_H
+#define _CONFIG_SBX81LIFXCAT_H
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg
+#define CONFIG_BUILD_TARGET "u-boot.kwb"
+
+/* additions for new ARM relocation support */
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+#define CONFIG_KIRKWOOD_GPIO 1
+
+#define CONFIG_MISC_INIT_R /* call misc_init_r */
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define MTDPARTS_DEFAULT "mtdparts=spi0.0:768K(boot)ro,256K(boot-env),14M(user),1M(errlog)"
+#define MTDPARTS_MTDOOPS "errlog"
+#define CONFIG_DOS_PARTITION
+
+/*
+ * Environment variables configurations
+ */
+#define CONFIG_ENV_SPI_BUS 0
+#define CONFIG_ENV_SPI_CS 0
+#define CONFIG_ENV_SPI_MAX_HZ 20000000 /* 20Mhz */
+#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_ENV_SECT_SIZE 0x40000 /* 256K */
+#define CONFIG_ENV_SIZE 0x02000
+#define CONFIG_ENV_OFFSET 0xc0000 /* env starts here - 768K */
+
+/*
+ * U-Boot bootcode configuration
+ */
+
+#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for monitor */
+#define CONFIG_SYS_MALLOC_LEN (4 << 20) /* Reserve 4.0 MB for malloc */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Mem map for Linux*/
+
+/* size in bytes reserved for initial data */
+
+#include <asm/arch/config.h>
+/* There is no PHY directly connected so don't ask it for link status */
+#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi over miiphy interface */
+#define CONFIG_MVGBE /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_MVGBE_PORTS {1, 0} /* enable a single port */
+#define CONFIG_PHY_BASE_ADR 0x01
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#endif /* CONFIG_CMD_NET */
+
+#define CONFIG_SYS_LOAD_ADDR 0x1000000 /* default location for tftp and bootm */
+
+#endif /* _CONFIG_SBX81LIFXCAT_H */
diff --git a/include/configs/clearfog.h b/include/configs/clearfog.h
index 1141aee..7d56dfd 100644
--- a/include/configs/clearfog.h
+++ b/include/configs/clearfog.h
@@ -70,16 +70,6 @@
"initrd_high=0x10000000\0"
/* SPL */
-/*
- * Select the boot device here
- *
- * Currently supported are:
- * SPL_BOOT_SPI_NOR_FLASH - Booting via SPI NOR flash
- * SPL_BOOT_SDIO_MMC_CARD - Booting via SDIO/MMC card (partition 1)
- */
-#define SPL_BOOT_SPI_NOR_FLASH 1
-#define SPL_BOOT_SDIO_MMC_CARD 2
-#define CONFIG_SPL_BOOT_DEVICE SPL_BOOT_SDIO_MMC_CARD
/* Defines for SPL */
#define CONFIG_SPL_SIZE (140 << 10)
@@ -96,13 +86,11 @@
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SPI_NOR_FLASH
+#if defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI)
/* SPL related SPI defines */
#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
-#endif
-
-#if CONFIG_SPL_BOOT_DEVICE == SPL_BOOT_SDIO_MMC_CARD
+#elif defined(CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC)
/* SPL related MMC defines */
#define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10)
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
diff --git a/include/configs/dns325.h b/include/configs/dns325.h
index 0d52ffb..8658c80 100644
--- a/include/configs/dns325.h
+++ b/include/configs/dns325.h
@@ -55,13 +55,6 @@
#endif
/*
- * RTC driver configuration
- */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_MV
-#endif
-
-/*
* Enable GPI0 support
*/
#define CONFIG_KIRKWOOD_GPIO
diff --git a/include/configs/goflexhome.h b/include/configs/goflexhome.h
index 29e104f..1d69a4e 100644
--- a/include/configs/goflexhome.h
+++ b/include/configs/goflexhome.h
@@ -93,11 +93,4 @@
#define CONFIG_SYS_ATA_IDE0_OFFSET MV_SATA_PORT0_OFFSET
#endif /*CONFIG_MVSATA_IDE*/
-/*
- * * RTC driver configuration
- * */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_MV
-#endif /* CONFIG_CMD_DATE */
-
#endif /* _CONFIG_GOFLEXHOME_H */
diff --git a/include/configs/mv-plug-common.h b/include/configs/mv-plug-common.h
index 81c07a8..f424e2c 100644
--- a/include/configs/mv-plug-common.h
+++ b/include/configs/mv-plug-common.h
@@ -22,11 +22,4 @@
*/
#include "mv-common.h"
-/*
- * RTC driver configuration
- */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_MV
-#endif /* CONFIG_CMD_DATE */
-
#endif /* _CONFIG_MARVELL_PLUG_H */
diff --git a/include/configs/mvebu_armada-37xx.h b/include/configs/mvebu_armada-37xx.h
index d133109..5015bc7 100644
--- a/include/configs/mvebu_armada-37xx.h
+++ b/include/configs/mvebu_armada-37xx.h
@@ -66,6 +66,8 @@
#define CONFIG_SF_DEFAULT_SPEED 1000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
+#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
+#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
/* Environment in SPI NOR flash */
#define CONFIG_ENV_OFFSET 0x180000 /* as Marvell U-Boot version */
diff --git a/include/configs/nas220.h b/include/configs/nas220.h
index b37705e..ca5cb2a 100644
--- a/include/configs/nas220.h
+++ b/include/configs/nas220.h
@@ -107,13 +107,6 @@
* EFI partition
*/
-/*
- * Date Time
- */
-#ifdef CONFIG_CMD_DATE
-#define CONFIG_RTC_MV
-#endif /* CONFIG_CMD_DATE */
-
#define CONFIG_KIRKWOOD_GPIO
#endif /* _CONFIG_NAS220_H */
diff --git a/include/configs/turris_omnia.h b/include/configs/turris_omnia.h
index 9d4d0df..44d5016 100644
--- a/include/configs/turris_omnia.h
+++ b/include/configs/turris_omnia.h
@@ -93,13 +93,13 @@
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
-#ifdef CONFIG_TURRIS_OMNIA_SPL_BOOT_DEVICE_SPI
+#ifdef CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI
/* SPL related SPI defines */
# define CONFIG_SYS_SPI_U_BOOT_OFFS 0x24000
# define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
#endif
-#ifdef CONFIG_TURRIS_OMNIA_SPL_BOOT_DEVICE_MMC
+#ifdef CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC
/* SPL related MMC defines */
# define CONFIG_SYS_MMC_U_BOOT_OFFS (160 << 10)
# define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_MMC_U_BOOT_OFFS
diff --git a/tools/kwboot.c b/tools/kwboot.c
index 8a421cd..50ae2b4 100644
--- a/tools/kwboot.c
+++ b/tools/kwboot.c
@@ -182,7 +182,7 @@
}
n = read(fd, buf, len);
- if (n < 0)
+ if (n <= 0)
goto out;
buf = (char *)buf + n;
@@ -466,7 +466,7 @@
char _buf[128], *buf = _buf;
nin = read(in, buf, sizeof(buf));
- if (nin < 0)
+ if (nin <= 0)
return -1;
if (quit) {
@@ -821,7 +821,7 @@
perror("debugmsg");
goto out;
}
- } else {
+ } else if (bootmsg) {
rc = kwboot_bootmsg(tty, bootmsg);
if (rc) {
perror("bootmsg");