// SPDX-License-Identifier: GPL-2.0
/*
 * dts file for Xilinx ZynqMP Generic System Controller
 *
 * (C) Copyright 2021 - 2022, Xilinx, Inc.
 * (C) Copyright 2022 - 2023, Advanced Micro Devices, Inc.
 *
 * Michal Simek <michal.simek@amd.com>
 */
/dts-v1/;

#include "zynqmp.dtsi"
#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/net/ti-dp83867.h>
#include <dt-bindings/pinctrl/pinctrl-zynqmp.h>
#include <dt-bindings/phy/phy.h>

/ {
	model = "ZynqMP Generic System Controller";
	compatible = "xlnx,zynqmp-sc-revB", "xlnx,zynqmp-sc", "xlnx,zynqmp";

	aliases {
		i2c0 = &i2c0;
		i2c1 = &i2c1;
		mmc0 = &sdhci0;
		mmc1 = &sdhci1;
		nvmem0 = &eeprom;
		rtc0 = &rtc;
		serial0 = &uart0;
		serial1 = &uart1;
		serial2 = &dcc;
		spi0 = &qspi;
		spi1 = &spi0;
		spi2 = &spi1;
	};

	chosen {
		bootargs = "earlycon";
		stdout-path = "serial1:115200n8";
	};

	memory@0 {
		device_type = "memory";
		reg = <0x0 0x0 0x0 0x80000000>;
	};

	gpio-keys {
		compatible = "gpio-keys";
		autorepeat;
		fwuen {
			label = "sw16";
			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
			linux,code = <BTN_MISC>;
			wakeup-source;
			autorepeat;
		};
	};

	leds {
		compatible = "gpio-leds";
		ds40-led {
			label = "heartbeat";
			gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
			linux,default-trigger = "heartbeat";
		};
		ds44-led {
			label = "status";
			gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
		};
	};

	si5332_2: si5332-2 { /* u42 */
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <26000000>;
	};

	pwm-fan {
		compatible = "pwm-fan";
		status = "okay";
		pwms = <&ttc0 2 40000 1>;
	};
};

&gpio {
	status = "okay";
	gpio-line-names = "QSPI_CLK", "QSPI_DQ1", "QSPI_DQ2", "QSPI_DQ3", "QSPI_DQ0", /* 0 - 4 */
		"QSPI_CS_B", "", "LED1", "LED2", "", /* 5 - 9 */
		"", "ZU4_TRIGGER", "FWUEN", "EMMC_DAT0", "EMMC_DAT1", /* 10 - 14 */
		"EMMC_DAT2", "EMMC_DAT3", "EMMC_DAT4", "EMMC_DAT5", "EMMC_DAT6", /* 15 - 19 */
		"EMMC_DAT7", "EMMC_CMD", "EMMC_CLK", "EMMC_RST_B", "I2C1_SCL", /* 20 - 24 */
		"I2C1_SDA", "UART0_RXD", "UART0_TXD", "", "", /* 25 - 29 */
		"", "", "", "", "I2C0_SCL", /* 30 - 34 */
		"I2C0_SDA", "UART1_TXD", "UART1_RXD", "GEM_TX_CLK", "GEM_TX_D0", /* 35 - 39 */
		"GEM_TX_D1", "GEM_TX_D2", "GEM_TX_D3", "GEM_TX_CTL", "GEM_RX_CLK", /* 40 - 44 */
		"GEM_RX_D0", "GEM_RX_D1", "GEM_RX_D2", "GEM_RX_D3", "GEM_RX_CTL", /* 45 - 49 */
		"GEM_MDC", "GEM_MDIO", "USB0_CLK", "USB0_DIR", "USB0_DATA2", /* 50 - 54 */
		"USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", /* 55 - 59 */
		"USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "", /* 60 - 64 */
		"", "", "", "", "", /* 65 - 69 */
		"", "", "", "", "", /* 70 - 74 */
		"", "", "ETH_RESET_B", /* 75 - 77, MIO end and EMIO start */
		"", "", /* 78 - 79 */
		"", "", "", "", "", /* 80 - 84 */
		"", "", "", "", "", /* 85 -89 */
		"", "", "", "", "", /* 90 - 94 */
		"", "", "", "", "", /* 95 - 99 */
		"", "", "", "", "", /* 100 - 104 */
		"", "", "", "", "", /* 105 - 109 */
		"", "", "", "", "", /* 110 - 114 */
		"", "", "", "", "", /* 115 - 119 */
		"", "", "", "", "", /* 120 - 124 */
		"", "", "", "", "", /* 125 - 129 */
		"", "", "", "", "", /* 130 - 134 */
		"", "", "", "", "", /* 135 - 139 */
		"", "", "", "", "", /* 140 - 144 */
		"", "", "", "", "", /* 145 - 149 */
		"", "", "", "", "", /* 150 - 154 */
		"", "", "", "", "", /* 155 - 159 */
		"", "", "", "", "", /* 160 - 164 */
		"", "", "", "", "", /* 165 - 169 */
		"", "", "", ""; /* 170 - 173 */
};

&gem1 { /* gem1 MIO38-49, MDIO MIO50/51 */
	status = "okay";
	phy-mode = "rgmii-id";
	phy-handle = <&phy0>;
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_gem1_default>;

	mdio: mdio {
		#address-cells = <1>;
		#size-cells = <0>;

		phy0: ethernet-phy@1 {
			#phy-cells = <1>;
			compatible = "ethernet-phy-id2000.a231";
			reg = <1>;
			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>;
			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
			ti,dp83867-rxctrl-strap-quirk;
			reset-gpios = <&gpio 77 GPIO_ACTIVE_LOW>;
			reset-assert-us = <100>;
			reset-deassert-us = <280>;
		};
	};
};

&i2c0 {
	#address-cells = <1>;
	#size-cells = <0>;
	status = "okay";
	clock-frequency = <100000>;
	pinctrl-names = "default", "gpio";
	pinctrl-0 = <&pinctrl_i2c0_default>;
	pinctrl-1 = <&pinctrl_i2c0_gpio>;
	scl-gpios = <&gpio 34 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
	sda-gpios = <&gpio 35 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
};

&i2c1 { /* i2c1 MIO 24-25 */
	status = "okay";
	bootph-all;
	clock-frequency = <100000>;
	pinctrl-names = "default", "gpio";
	pinctrl-0 = <&pinctrl_i2c1_default>;
	pinctrl-1 = <&pinctrl_i2c1_gpio>;
	scl-gpios = <&gpio 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
	sda-gpios = <&gpio 25 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;

	/* Use for storing information about SC board */
	eeprom: eeprom@54 { /* u34 - m24128 16kB */
		compatible = "st,24c128", "atmel,24c128";
		reg = <0x54>; /* & 0x5c */
		bootph-all;
	};
};

/* USB 3.0 only */
&psgtr {
	status = "okay";
	/* nc, nc, usb3 */
	clocks = <&si5332_2>;
	clock-names = "ref2";
};

&qspi { /* MIO 0-5 */
	status = "okay";
	/* QSPI should also have PINCTRL setup */
	flash@0 {
		compatible = "mt25qu512a", "m25p80", "jedec,spi-nor"; /* mt25qu512abb8e12 512Mib */
		#address-cells = <1>;
		#size-cells = <1>;
		reg = <0>;
		spi-tx-bus-width = <4>;
		spi-rx-bus-width = <4>;
		spi-max-frequency = <40000000>; /* 40MHz */
		partition@0 {
			label = "Image Selector";
			reg = <0x0 0x80000>; /* 512KB */
			read-only;
			lock;
		};
		partition@80000 {
			label = "Image Selector Golden";
			reg = <0x80000 0x80000>; /* 512KB */
			read-only;
			lock;
		};
		partition@100000 {
			label = "Persistent Register";
			reg = <0x100000 0x20000>; /* 128KB */
		};
		partition@120000 {
			label = "Persistent Register Backup";
			reg = <0x120000 0x20000>; /* 128KB */
		};
		partition@140000 {
			label = "Open_1";
			reg = <0x140000 0xC0000>; /* 768KB */
		};
		partition@200000 {
			label = "Image A (FSBL, PMU, ATF, U-Boot)";
			reg = <0x200000 0xD00000>; /* 13MB */
		};
		partition@f00000 {
			label = "ImgSel Image A Catch";
			reg = <0xF00000 0x80000>; /* 512KB */
			read-only;
			lock;
		};
		partition@f80000 {
			label = "Image B (FSBL, PMU, ATF, U-Boot)";
			reg = <0xF80000 0xD00000>; /* 13MB */
		};
		partition@1c80000 {
			label = "ImgSel Image B Catch";
			reg = <0x1C80000 0x80000>; /* 512KB */
			read-only;
			lock;
		};
		partition@1d00000 {
			label = "Open_2";
			reg = <0x1D00000 0x100000>; /* 1MB */
		};
		partition@1e00000 {
			label = "Recovery Image";
			reg = <0x1E00000 0x200000>; /* 2MB */
			read-only;
			lock;
		};
		partition@2000000 {
			label = "Recovery Image Backup";
			reg = <0x2000000 0x200000>; /* 2MB */
			read-only;
			lock;
		};
		partition@2200000 {
			label = "U-Boot storage variables";
			reg = <0x2200000 0x20000>; /* 128KB */
		};
		partition@2220000 {
			label = "U-Boot storage variables backup";
			reg = <0x2220000 0x20000>; /* 128KB */
		};
		partition@2240000 {
			label = "SHA256";
			reg = <0x2240000 0x40000>; /* 256B but 256KB sector */
			read-only;
			lock;
		};
		partition@2280000 {
			label = "Secure OS Storage";
			reg = <0x2280000 0x20000>; /* 128KB */
		};
		partition@22A0000 {
			label = "User";
			reg = <0x22A0000 0x1d60000>; /* 29.375 MB */
		};
	};
};

&sdhci0 { /* emmc MIO 13-23 - with some settings MTFC16GAPALBH 16GB */
	status = "okay";
	non-removable;
	disable-wp;
	bus-width = <8>;
	xlnx,mio-bank = <0>;
};

&ttc0 {
	status = "okay";
	#pwm-cells = <3>;
};

&uart1 { /* uart0 MIO36-37 */
	status = "okay";
	pinctrl-names = "default";
	pinctrl-0 = <&pinctrl_uart1_default>;
};

&pinctrl0 { /* required by spec */
	status = "okay";

	pinctrl_uart1_default: uart1-default {
		conf {
			groups = "uart1_9_grp";
			slew-rate = <SLEW_RATE_SLOW>;
			power-source = <IO_STANDARD_LVCMOS18>;
			drive-strength = <12>;
		};

		conf-rx {
			pins = "MIO37";
			bias-high-impedance;
		};

		conf-tx {
			pins = "MIO36";
			bias-disable;
		};

		mux {
			groups = "uart1_9_grp";
			function = "uart1";
		};
	};

	pinctrl_i2c0_default: i2c0-default {
		mux {
			groups = "i2c0_8_grp";
			function = "i2c0";
		};

		conf {
			groups = "i2c0_8_grp";
			bias-pull-up;
			slew-rate = <SLEW_RATE_SLOW>;
			power-source = <IO_STANDARD_LVCMOS18>;
		};
	};

	pinctrl_i2c0_gpio: i2c0-gpio-grp {
		mux {
			groups = "gpio0_34_grp", "gpio0_35_grp";
			function = "gpio0";
		};

		conf {
			groups = "gpio0_34_grp", "gpio0_35_grp";
			slew-rate = <SLEW_RATE_SLOW>;
			power-source = <IO_STANDARD_LVCMOS18>;
		};
	};

	pinctrl_i2c1_default: i2c1-default {
		conf {
			groups = "i2c1_6_grp";
			bias-pull-up;
			slew-rate = <SLEW_RATE_SLOW>;
			power-source = <IO_STANDARD_LVCMOS18>;
		};

		mux {
			groups = "i2c1_6_grp";
			function = "i2c1";
		};
	};

	pinctrl_i2c1_gpio: i2c1-gpio-grp {
		conf {
			groups = "gpio0_24_grp", "gpio0_25_grp";
			slew-rate = <SLEW_RATE_SLOW>;
			power-source = <IO_STANDARD_LVCMOS18>;
		};

		mux {
			groups = "gpio0_24_grp", "gpio0_25_grp";
			function = "gpio0";
		};
	};

	pinctrl_gem1_default: gem1-default {
		conf {
			groups = "ethernet1_0_grp";
			slew-rate = <SLEW_RATE_SLOW>;
			power-source = <IO_STANDARD_LVCMOS18>;
		};

		conf-rx {
			pins = "MIO44", "MIO46", "MIO48";
			bias-high-impedance;
			low-power-disable;
		};

		conf-bootstrap {
			pins = "MIO45", "MIO47", "MIO49";
			bias-disable;
			low-power-disable;
		};

		conf-tx {
			pins = "MIO38", "MIO39", "MIO40",
				"MIO41", "MIO42", "MIO43";
			bias-disable;
			low-power-enable;
		};

		conf-mdio {
			groups = "mdio1_0_grp";
			slew-rate = <SLEW_RATE_SLOW>;
			power-source = <IO_STANDARD_LVCMOS18>;
			bias-disable;
		};

		mux-mdio {
			function = "mdio1";
			groups = "mdio1_0_grp";
		};

		mux {
			function = "ethernet1";
			groups = "ethernet1_0_grp";
		};
	};
};