diff --git a/board/freescale/b4860qds/eth_b4860qds.c b/board/freescale/b4860qds/eth_b4860qds.c
index 4b2303e..164ec0a 100644
--- a/board/freescale/b4860qds/eth_b4860qds.c
+++ b/board/freescale/b4860qds/eth_b4860qds.c
@@ -269,7 +269,7 @@
 		fm_info_set_phy_address(FM1_DTSEC4,
 				CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR);
 		/*
-		 * XFI does not need a PHY to work, but to make U-boot
+		 * XFI does not need a PHY to work, but to make U-Boot
 		 * happy, assign a fake PHY address for a XFI port.
 		 */
 		fm_info_set_phy_address(FM1_10GEC1, 0);
diff --git a/board/freescale/bsc9131rdb/README b/board/freescale/bsc9131rdb/README
index 4902b98..c840597 100644
--- a/board/freescale/bsc9131rdb/README
+++ b/board/freescale/bsc9131rdb/README
@@ -86,9 +86,9 @@
 --------------------
 NAND boot
 
-Building U-boot
+Building U-Boot
 --------------
-To build the u-boot for BSC9131RDB:
+To build the U-Boot for BSC9131RDB:
 1. NAND Flash with sysclk 66MHz(J16 on RDB closed, default)
 	make BSC9131RDB_NAND
 2. NAND Flash with sysclk 100MHz(J16 on RDB open)
@@ -123,7 +123,7 @@
 
 Flashing Images
 ---------------
-To place a new u-boot image in the NAND flash and then boot
+To place a new U-Boot image in the NAND flash and then boot
 with that new image temporarily, use this:
 	tftp 1000000 u-boot-nand.bin
 	nand erase 0 100000
diff --git a/board/freescale/bsc9132qds/README b/board/freescale/bsc9132qds/README
index f8377c9..ede95d4 100644
--- a/board/freescale/bsc9132qds/README
+++ b/board/freescale/bsc9132qds/README
@@ -87,9 +87,9 @@
 --------------------
 NOR boot
 
-Building U-boot
+Building U-Boot
 --------------
-To build the u-boot for BSC9132QDS:
+To build the U-Boot for BSC9132QDS:
 1. NOR Flash
 	make BSC9132QDS_NOR_DDRCLK100 : For 100MHZ DDR CLK
 	make BSC9132QDS_NOR_DDRCLK133 : For 133MHZ DDR CLK
@@ -122,7 +122,7 @@
 
 Flashing Images
 ---------------
-To place a new u-boot image in the NAND flash and then boot
+To place a new U-Boot image in the NAND flash and then boot
 with that new image temporarily, use this:
 	tftp 1000000 u-boot-nand.bin
 	nand erase 0 100000
diff --git a/board/freescale/c29xpcie/README b/board/freescale/c29xpcie/README
index 3bc396b..2e249cb 100644
--- a/board/freescale/c29xpcie/README
+++ b/board/freescale/c29xpcie/README
@@ -53,7 +53,7 @@
   SW5[1:4]= 0110 and SW5[6]=0 for boot from SPI flash
 Note: 1 stands for 'off', 0 stands for 'on'
 
-Build and program u-boot to NOR flash
+Build and program U-Boot to NOR flash
 ==================================
 1. Build u-boot.bin image example:
 	export ARCH=powerpc
@@ -86,7 +86,7 @@
 	- bank 4 on the flash 0x3000000~0x3ffffff
 	or set SW5[7]= ON/OFF and SW5[7]= ON/OFF, then power on again.
 
-Build and program u-boot to SPI flash
+Build and program U-Boot to SPI flash
 ==================================
 1. Build u-boot-spi.bin image
 	make C29xPCIE_SPIFLASH_config; make
diff --git a/board/freescale/ls2080a/README b/board/freescale/ls2080a/README
index 7e53f1f..646cc02 100644
--- a/board/freescale/ls2080a/README
+++ b/board/freescale/ls2080a/README
@@ -12,7 +12,7 @@
 0x05_1000_0000 .. 0x05_FFFF_FFFF	IFC region #2
 0x80_8000_0000 .. 0xFF_FFFF_FFFF	DDR region #2
 
-Other addresses are either reserved, or not used directly by u-boot.
+Other addresses are either reserved, or not used directly by U-Boot.
 This list should be updated when more addresses are used.
 
 Booting Linux flavors which do not support 48-bit VA (< Linux 3.18)
diff --git a/board/freescale/ls2080aqds/README b/board/freescale/ls2080aqds/README
index 375e97c..6ddad92 100644
--- a/board/freescale/ls2080aqds/README
+++ b/board/freescale/ls2080aqds/README
@@ -103,7 +103,7 @@
 0x05_1000_0000 .. 0x05_FFFF_FFFF	IFC region #2
 0x80_8000_0000 .. 0xFF_FFFF_FFFF	DDR region #2
 
-Other addresses are either reserved, or not used directly by u-boot.
+Other addresses are either reserved, or not used directly by U-Boot.
 This list should be updated when more addresses are used.
 
 IFC region map from core's view
diff --git a/board/freescale/ls2080aqds/eth.c b/board/freescale/ls2080aqds/eth.c
index ebc9d47..42ff743 100644
--- a/board/freescale/ls2080aqds/eth.c
+++ b/board/freescale/ls2080aqds/eth.c
@@ -716,7 +716,7 @@
 	switch (serdes1_prtcl) {
 	case 0x2A:
 		/*
-		 * XFI does not need a PHY to work, but to avoid U-boot use
+		 * XFI does not need a PHY to work, but to avoid U-Boot use
 		 * default PHY address which is zero to a MAC when it found
 		 * a MAC has no PHY address, we give a PHY address to XFI
 		 * MAC, and should not use a real XAUI PHY address, since
diff --git a/board/freescale/ls2080ardb/README b/board/freescale/ls2080ardb/README
index 7fc2569..6708ca9 100644
--- a/board/freescale/ls2080ardb/README
+++ b/board/freescale/ls2080ardb/README
@@ -87,7 +87,7 @@
 0x05_1000_0000 .. 0x05_FFFF_FFFF	IFC region #2
 0x80_8000_0000 .. 0xFF_FFFF_FFFF	DDR region #2
 
-Other addresses are either reserved, or not used directly by u-boot.
+Other addresses are either reserved, or not used directly by U-Boot.
 This list should be updated when more addresses are used.
 
 IFC region map from core's view
diff --git a/board/freescale/m52277evb/README b/board/freescale/m52277evb/README
index 3178d49..92a8384 100644
--- a/board/freescale/m52277evb/README
+++ b/board/freescale/m52277evb/README
@@ -49,7 +49,7 @@
 - include/asm-m68k/timer.h		Timer structure and definition
 - include/asm-m68k/types.h		Data types definition
 - include/asm-m68k/uart.h		Uart structure and definition
-- include/asm-m68k/u-boot.h		u-boot structure
+- include/asm-m68k/u-boot.h		U-Boot structure
 
 - include/configs/M52277EVB.h		Board specific configuration file
 
@@ -77,7 +77,7 @@
 CONFIG_SYS_MCFRTC_BASE		-- provide base address for RTC in immap.h
 CONFIG_SYS_RTC_OSCILLATOR	-- define RTC clock frequency
 RTC_DEBUG		-- define to show RTC debug message
-CONFIG_CMD_DATE		-- enable to use date feature in u-boot
+CONFIG_CMD_DATE		-- enable to use date feature in U-Boot
 
 CONFIG_MCFTMR		-- define to use DMA timer
 CONFIG_MCFPIT		-- define to use PIT timer
@@ -102,7 +102,7 @@
 
 CONFIG_SYS_SDRAM_BASE	-- defines the DRAM Base
 
-CONFIG_LCD and CONFIG_CMD_USB are not supported in this current u-boot,
+CONFIG_LCD and CONFIG_CMD_USB are not supported in this current U-Boot,
 update will be provided at later time
 
 2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
@@ -113,7 +113,7 @@
 	SRAM:		0x80000000-0x8FFFFFFF (256MB)
 	IP:		0xF0000000-0xFFFFFFFF (256MB)
 
-2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+2.2. For the initial bringup, we adopted a consistent memory scheme between U-Boot and
 	linux kernel, you can customize it based on your system requirements:
 	Flash0:		0x00000000-0x00FFFFFF (16MB)
 
diff --git a/board/freescale/m5253evbe/README b/board/freescale/m5253evbe/README
index f51609f..2ed5c76 100644
--- a/board/freescale/m5253evbe/README
+++ b/board/freescale/m5253evbe/README
@@ -13,7 +13,7 @@
 
 2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
 ===========================================
-2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+2.1. For the initial bringup, we adopted a consistent memory scheme between U-Boot and
 	linux kernel, you can customize it based on your system requirements:
 	SDR:	0x00000000-0x00ffffff
 	SRAM0:	0x20010000-0x20017fff
diff --git a/board/freescale/m53017evb/README b/board/freescale/m53017evb/README
index 84fc1ec..224e79c 100644
--- a/board/freescale/m53017evb/README
+++ b/board/freescale/m53017evb/README
@@ -47,7 +47,7 @@
 - include/asm-m68k/timer.h		Timer structure and definition
 - include/asm-m68k/types.h		Data types definition
 - include/asm-m68k/uart.h		Uart structure and definition
-- include/asm-m68k/u-boot.h		u-boot structure
+- include/asm-m68k/u-boot.h		U-Boot structure
 
 - include/configs/M53017EVB.h		Board specific configuration file
 
@@ -75,7 +75,7 @@
 CONFIG_SYS_MCFRTC_BASE		-- provide base address for RTC in immap.h
 CONFIG_SYS_RTC_OSCILLATOR	-- define RTC clock frequency
 RTC_DEBUG			-- define to show RTC debug message
-CONFIG_CMD_DATE			-- enable to use date feature in u-boot
+CONFIG_CMD_DATE			-- enable to use date feature in U-Boot
 
 CONFIG_MCFFEC			-- define to use common CF FEC driver
 CONFIG_MII			-- enable to use MII driver
@@ -118,7 +118,7 @@
 	SRAM:		0x80000000-0x8FFFFFFF (256MB)
 	IP:		0xFC000000-0xFFFFFFFF (256MB)
 
-2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+2.2. For the initial bringup, we adopted a consistent memory scheme between U-Boot and
 	linux kernel, you can customize it based on your system requirements:
 	Flash0:		0x00000000-0x00FFFFFF (16MB)
 	DDR:		0x40000000-0x4FFFFFFF (256MB)
diff --git a/board/freescale/m5373evb/README b/board/freescale/m5373evb/README
index 52eac7b..582e0c3 100644
--- a/board/freescale/m5373evb/README
+++ b/board/freescale/m5373evb/README
@@ -46,7 +46,7 @@
 - include/asm-m68k/timer.h		Timer structure and definition
 - include/asm-m68k/types.h		Data types definition
 - include/asm-m68k/uart.h		Uart structure and definition
-- include/asm-m68k/u-boot.h		u-boot structure
+- include/asm-m68k/u-boot.h		U-Boot structure
 
 - include/configs/M5373EVB.h		Board specific configuration file
 
@@ -74,7 +74,7 @@
 CONFIG_SYS_MCFRTC_BASE		-- provide base address for RTC in immap.h
 CONFIG_SYS_RTC_OSCILLATOR	-- define RTC clock frequency
 RTC_DEBUG		-- define to show RTC debug message
-CONFIG_CMD_DATE		-- enable to use date feature in u-boot
+CONFIG_CMD_DATE		-- enable to use date feature in U-Boot
 
 CONFIG_MCFFEC		-- define to use common CF FEC driver
 CONFIG_MII		-- enable to use MII driver
@@ -117,7 +117,7 @@
 	SRAM:		0x80000000-0x8FFFFFFF (256MB)
 	IP:		0xF0000000-0xFFFFFFFF (256MB)
 
-2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+2.2. For the initial bringup, we adopted a consistent memory scheme between U-Boot and
 	linux kernel, you can customize it based on your system requirements:
 	Flash0:		0x00000000-0x00FFFFFF (16MB)
 
diff --git a/board/freescale/m54455evb/README b/board/freescale/m54455evb/README
index c70c4c5..c563ad9 100644
--- a/board/freescale/m54455evb/README
+++ b/board/freescale/m54455evb/README
@@ -48,7 +48,7 @@
 - include/asm-m68k/timer.h		Timer structure and definition
 - include/asm-m68k/types.h		Data types definition
 - include/asm-m68k/uart.h		Uart structure and definition
-- include/asm-m68k/u-boot.h		u-boot structure
+- include/asm-m68k/u-boot.h		U-Boot structure
 
 - include/configs/M54455EVB.h	Board specific configuration file
 
@@ -78,7 +78,7 @@
 CONFIG_SYS_MCFRTC_BASE		-- provide base address for RTC in immap.h
 CONFIG_SYS_RTC_OSCILLATOR	-- define RTC clock frequency
 RTC_DEBUG		-- define to show RTC debug message
-CONFIG_CMD_DATE		-- enable to use date feature in u-boot
+CONFIG_CMD_DATE		-- enable to use date feature in U-Boot
 
 CONFIG_MCFFEC		-- define to use common CF FEC driver
 CONFIG_MII		-- enable to use MII driver
@@ -91,7 +91,7 @@
 CONFIG_SYS_FEC0_MIIBASE	-- Set FEC0 MII base register
 CONFIG_SYS_FEC1_MIIBASE	-- Set FEC0 MII base register
 MCFFEC_TOUT_LOOP	-- set FEC timeout loop
-CONFIG_HAS_ETH1		-- define to enable second FEC in u-boot
+CONFIG_HAS_ETH1		-- define to enable second FEC in U-Boot
 
 CONFIG_ISO_PARTITION	-- enable ISO read/write
 CONFIG_DOS_PARTITION	-- enable DOS read/write
@@ -136,7 +136,7 @@
 
 CONFIG_SYS_MBAR		-- define MBAR offset
 
-CONFIG_SYS_ATMEL_BOOT		-- To determine the u-boot is booted from Atmel or Intel
+CONFIG_SYS_ATMEL_BOOT		-- To determine the U-Boot is booted from Atmel or Intel
 
 CONFIG_MONITOR_IS_IN_RAM -- Not support
 
@@ -163,7 +163,7 @@
 	FlexBus:	0xC0000000-0xDFFFFFFF (512MB)
 	IP:		0xF0000000-0xFFFFFFFF (256MB)
 
-2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+2.2. For the initial bringup, we adopted a consistent memory scheme between U-Boot and
 	linux kernel, you can customize it based on your system requirements:
 	Atmel boot:
 	Flash0:		0x00000000-0x0007FFFF (512KB)
diff --git a/board/freescale/m547xevb/README b/board/freescale/m547xevb/README
index ce497c0..30c5ded 100644
--- a/board/freescale/m547xevb/README
+++ b/board/freescale/m547xevb/README
@@ -54,7 +54,7 @@
 - include/asm-m68k/timer.h		Timer structure and definition
 - include/asm-m68k/types.h		Data types definition
 - include/asm-m68k/uart.h		Uart structure and definition
-- include/asm-m68k/u-boot.h		u-boot structure
+- include/asm-m68k/u-boot.h		U-Boot structure
 
 - include/configs/M5475EVB.h		Board specific configuration file
 
@@ -88,7 +88,7 @@
 CONFIG_SYS_FEC0_MIIBASE	-- Set FEC0 MII base register
 CONFIG_SYS_FEC1_MIIBASE	-- Set FEC0 MII base register
 MCFFEC_TOUT_LOOP	-- set FEC timeout loop
-CONFIG_HAS_ETH1		-- define to enable second FEC in u-boot
+CONFIG_HAS_ETH1		-- define to enable second FEC in U-Boot
 
 CONFIG_CMD_USB		-- enable USB commands
 CONFIG_USB_OHCI_NEW	-- enable USB OHCI driver
diff --git a/board/freescale/mpc8313erdb/README b/board/freescale/mpc8313erdb/README
index be7ef32..697cee4 100644
--- a/board/freescale/mpc8313erdb/README
+++ b/board/freescale/mpc8313erdb/README
@@ -70,7 +70,7 @@
 
 5.	Downloading and Flashing Images
 
-5.1	Reflash U-boot Image using U-boot
+5.1	Reflash U-Boot Image using U-Boot
 
 	NOR flash:
 
@@ -81,7 +81,7 @@
 	first, to make sure that the TFTP load will succeed before it
 	goes ahead and wipes out your current firmware.  And of course,
 	have an alternate means of programming the flash available
-	if the new u-boot doesn't boot.
+	if the new U-Boot doesn't boot.
 
 	NAND flash:
 
diff --git a/board/freescale/mpc8315erdb/README b/board/freescale/mpc8315erdb/README
index b32132d..8ad6d81 100644
--- a/board/freescale/mpc8315erdb/README
+++ b/board/freescale/mpc8315erdb/README
@@ -63,7 +63,7 @@
 
 5.	Downloading and Flashing Images
 
-5.1	Reflash U-boot Image using U-boot
+5.1	Reflash U-Boot Image using U-Boot
 
 	NOR flash:
 
diff --git a/board/freescale/mpc8323erdb/README b/board/freescale/mpc8323erdb/README
index 6f89829..9a46da0 100644
--- a/board/freescale/mpc8323erdb/README
+++ b/board/freescale/mpc8323erdb/README
@@ -22,10 +22,10 @@
 
 3.	Downloading and Flashing Images
 
-3.1	Reflash U-boot Image using U-boot
+3.1	Reflash U-Boot Image using U-Boot
 
 	N.b, have an alternate means of programming
-	the flash available if the new u-boot doesn't boot.
+	the flash available if the new U-Boot doesn't boot.
 
 	First try a:
 
@@ -44,7 +44,7 @@
 	erase fe000000 +$filesize
 	cp.b $loadaddr fe000000 $filesize
 
-	To keep your old u-boot's environment variables, do a:
+	To keep your old U-Boot's environment variables, do a:
 
 	saveenv
 
diff --git a/board/freescale/mpc832xemds/README b/board/freescale/mpc832xemds/README
index 4142aa9..d141cd3 100644
--- a/board/freescale/mpc832xemds/README
+++ b/board/freescale/mpc832xemds/README
@@ -97,7 +97,7 @@
 		make MPC832XEMDS_config
 		make
 
-	MPC832x support PCI 33MHz and PCI 66MHz, to make u-boot support PCI:
+	MPC832x support PCI 33MHz and PCI 66MHz, to make U-Boot support PCI:
 
 		1)Make sure the DIP SW support PCI mode as described in Section 1.1.
 
@@ -113,7 +113,7 @@
 
 	tftp 10000 u-boot.bin
 
-5.1 Reflash U-boot Image using U-boot
+5.1 Reflash U-Boot Image using U-Boot
 
 	tftp 20000 u-boot.bin
 	protect off fe000000 fe0fffff
diff --git a/board/freescale/mpc837xemds/README b/board/freescale/mpc837xemds/README
index faf21c9..dbb1517 100644
--- a/board/freescale/mpc837xemds/README
+++ b/board/freescale/mpc837xemds/README
@@ -90,7 +90,7 @@
 
 	tftp 40000 u-boot.bin
 
-5.1 Reflash U-boot Image using U-boot
+5.1 Reflash U-Boot Image using U-Boot
 
 	tftp 40000 u-boot.bin
 	protect off fe000000 fe1fffff
diff --git a/board/freescale/mpc837xerdb/README b/board/freescale/mpc837xerdb/README
index cfb6efa..12df2f2 100644
--- a/board/freescale/mpc837xerdb/README
+++ b/board/freescale/mpc837xerdb/README
@@ -84,7 +84,7 @@
 
 	tftp $loadaddr u-boot.bin
 
-5.1 Reflash U-boot Image using U-boot
+5.1 Reflash U-Boot Image using U-Boot
 
 	tftp $loadaddr u-boot.bin
 	protect off fe000000 fe0fffff
diff --git a/board/freescale/mpc8569mds/README b/board/freescale/mpc8569mds/README
index 3d12a96..86c3ccd 100644
--- a/board/freescale/mpc8569mds/README
+++ b/board/freescale/mpc8569mds/README
@@ -3,7 +3,7 @@
 MPC8569MDS is composed of two boards - PB (Processor Board) and PIB (Platform
 I/O Board). The mpc8569 PowerTM processor is mounted on PB board.
 
-Building U-boot
+Building U-Boot
 -----------
 	make MPC8569MDS_config
 	make
@@ -22,10 +22,10 @@
 0xfe00_0000   0xffff_ffff     Flash                   32MB
 
 
-Flashing u-boot Images
+Flashing U-Boot Images
 ---------------
 
-Use the following commands to program u-boot image into flash:
+Use the following commands to program U-Boot image into flash:
 
 	=> tftp 1000000 u-boot.bin
 	=> protect off all
diff --git a/board/freescale/mpc8572ds/README b/board/freescale/mpc8572ds/README
index 57fd2ad..f1ffdd1 100644
--- a/board/freescale/mpc8572ds/README
+++ b/board/freescale/mpc8572ds/README
@@ -3,7 +3,7 @@
 MPC8572DS is a high-performance computing, evaluation and development platform
 supporting the mpc8572 PowerTM processor.
 
-Building U-boot
+Building U-Boot
 -----------
 	make MPC8572DS_config
 	make
@@ -22,14 +22,14 @@
 0xe800_0000 - 0xebff_ffff	Alternate bank		64MB
 0xec00_0000 - 0xefff_ffff	Boot bank		64MB
 
-0xebf8_0000 - 0xebff_ffff	Alternate u-boot address	512KB
-0xeff8_0000 - 0xefff_ffff	Boot u-boot address		512KB
+0xebf8_0000 - 0xebff_ffff	Alternate U-Boot address	512KB
+0xeff8_0000 - 0xefff_ffff	Boot U-Boot address		512KB
 
 
 Flashing Images
 ---------------
 
-To place a new u-boot image in the alternate flash bank and then reset with that
+To place a new U-Boot image in the alternate flash bank and then reset with that
  new image temporarily, use this:
 
 	tftp 1000000 u-boot.bin
@@ -135,7 +135,7 @@
 
 5. Bring up two cores separately:
 
-	a. Power on the board, under u-boot prompt:
+	a. Power on the board, under U-Boot prompt:
 		=> setenv <serverip>
 		=> setenv <ipaddr>
 		=> setenv bootargs root=/dev/ram rw console=ttyS0,115200
@@ -154,7 +154,7 @@
 		=> fdt chosen $initrd_start $initrd_end
 		=> bootm prep
 		=> cpu 1 release $bootm_low - $fdtaddr -
-	c. Bring up core0's kernel(on the same u-boot console):
+	c. Bring up core0's kernel(on the same U-Boot console):
 		=> setenv bootm_low 0
 		=> setenv bootm_size 0x20000000
 		=> tftp 1000000 8572/uImage.core0
@@ -162,5 +162,5 @@
 		=> tftp c00000 8572/mpc8572ds_core0.dtb
 		=> bootm 1000000 2000000 c00000
 
-Please note only core0 will run u-boot, core1 starts kernel directly after
+Please note only core0 will run U-Boot, core1 starts kernel directly after
 "cpu release" command is issued.
diff --git a/board/freescale/mpc8610hpcd/README b/board/freescale/mpc8610hpcd/README
index 31a9af3..066e625 100644
--- a/board/freescale/mpc8610hpcd/README
+++ b/board/freescale/mpc8610hpcd/README
@@ -27,7 +27,7 @@
 	cp.b 1000000 fff00000 $filesize
 
 
-To Flash U-boot into the alternate bank
+To Flash U-Boot into the alternate bank
 
 	tftp 1000000 u-boot.bin
 	erase fbf00000 +$filesize
diff --git a/board/freescale/mpc8641hpcn/README b/board/freescale/mpc8641hpcn/README
index d8fe0a4..77909a8 100644
--- a/board/freescale/mpc8641hpcn/README
+++ b/board/freescale/mpc8641hpcn/README
@@ -80,7 +80,7 @@
 3. Flash U-Boot
 ---------------
 The flash range 0xEF800000 to 0xEFFFFFFF can be divided into 2 halves.
-It is possible to use either half to boot using u-boot.  Switch 5 bit 2
+It is possible to use either half to boot using U-Boot.  Switch 5 bit 2
 is used for this purpose.
 
 0xEF800000 to 0xEFBFFFFF - 4MB
@@ -102,7 +102,7 @@
 or use tftpflash command:
 	run tftpflash
 
-To Flash U-boot into the alternative bank (0xEF800000 - 0xEFBFFFFF):
+To Flash U-Boot into the alternative bank (0xEF800000 - 0xEFBFFFFF):
 
 	tftp 1000000 u-boot.bin
 	erase efb00000 +$filesize
@@ -113,7 +113,7 @@
 -------------
 NOTE:  RIO and PCI are mutually exclusive, so they share an address
 
-For 32-bit u-boot, devices are mapped so that the virtual address ==
+For 32-bit U-Boot, devices are mapped so that the virtual address ==
 the physical address, and the map looks liks this:
 
 	Memory Range			Device		Size
@@ -130,7 +130,7 @@
 	0xffc1_0000	0xffc1_ffff	PCI2/PEX2 IO	64K
 	0xef80_0000	0xefff_ffff	Flash		8M
 
-For 36-bit-enabled u-boot, the virtual map is the same as for 32-bit.
+For 36-bit-enabled U-Boot, the virtual map is the same as for 32-bit.
 However, the physical map is altered to reside in 36-bit space, as follows.
 Addresses are no longer mapped with VA == PA.  All accesses from
 software use the VA; the PA is only used for setting up windows
diff --git a/board/freescale/mx28evk/README b/board/freescale/mx28evk/README
index f9d6324..a248fb2 100644
--- a/board/freescale/mx28evk/README
+++ b/board/freescale/mx28evk/README
@@ -1,7 +1,7 @@
 FREESCALE MX28EVK
 ==================
 
-Supported hardware: MX28EVK rev C and D are supported in U-boot.
+Supported hardware: MX28EVK rev C and D are supported in U-Boot.
 
 Files of the MX28EVK port
 --------------------------
diff --git a/board/freescale/mx35pdk/README b/board/freescale/mx35pdk/README
index 7232b53..6f6841f 100644
--- a/board/freescale/mx35pdk/README
+++ b/board/freescale/mx35pdk/README
@@ -71,7 +71,7 @@
 Flashing U-Boot
 --------------------------------
 
-U-boot should be stored on the NOR flash.
+U-Boot should be stored on the NOR flash.
 
 The boot storage can be select using the switches on the personality board
 (SW1-SW2) and on the DEBUG board (SW4-SW10).
@@ -96,7 +96,7 @@
 To erase the whole partition:
 $ flash_eraseall /dev/mtd0
 
-Writing u-boot:
+Writing U-Boot:
 dd if=u-boot.bin of=/dev/mtd0
 
 To boot from NOR, you have to select the switches as follows:
diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c
index 46b4f3f..e9d9664 100644
--- a/board/freescale/mx6sabresd/mx6sabresd.c
+++ b/board/freescale/mx6sabresd/mx6sabresd.c
@@ -268,7 +268,7 @@
 
 	/*
 	 * According to the board_mmc_init() the following map is done:
-	 * (U-boot device node)    (Physical Port)
+	 * (U-Boot device node)    (Physical Port)
 	 * mmc0                    SD2
 	 * mmc1                    SD3
 	 * mmc2                    eMMC
diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c
index df205ea..4f816c4 100644
--- a/board/freescale/mx6slevk/mx6slevk.c
+++ b/board/freescale/mx6slevk/mx6slevk.c
@@ -202,7 +202,7 @@
 
 	/*
 	 * According to the board_mmc_init() the following map is done:
-	 * (U-boot device node)    (Physical Port)
+	 * (U-Boot device node)    (Physical Port)
 	 * mmc0                    USDHC1
 	 * mmc1                    USDHC2
 	 * mmc2                    USDHC3
diff --git a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
index c9631d2..a240982 100644
--- a/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
+++ b/board/freescale/mx6sxsabreauto/mx6sxsabreauto.c
@@ -339,7 +339,7 @@
 
 	/*
 	 * According to the board_mmc_init() the following map is done:
-	 * (U-boot device node)    (Physical Port)
+	 * (U-Boot device node)    (Physical Port)
 	 * mmc0                    USDHC3
 	 * mmc1                    USDHC4
 	 */
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
index 97e9ed7..41319c6 100644
--- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c
+++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c
@@ -348,7 +348,7 @@
 
 	/*
 	 * According to the board_mmc_init() the following map is done:
-	 * (U-boot device node)    (Physical Port)
+	 * (U-Boot device node)    (Physical Port)
 	 * mmc0                    USDHC2
 	 * mmc1                    USDHC3
 	 * mmc2                    USDHC4
diff --git a/board/freescale/mx6ul_14x14_evk/README b/board/freescale/mx6ul_14x14_evk/README
index d48c7ba..1edccf6 100644
--- a/board/freescale/mx6ul_14x14_evk/README
+++ b/board/freescale/mx6ul_14x14_evk/README
@@ -1,7 +1,7 @@
-How to use U-boot on Freescale MX6UL 14x14 EVK
+How to use U-Boot on Freescale MX6UL 14x14 EVK
 -----------------------------------------------
 
-- Build U-boot for MX6UL 14x14 EVK:
+- Build U-Boot for MX6UL 14x14 EVK:
 
 $ make mrproper
 $ make mx6ul_14x14_evk_defconfig
@@ -28,5 +28,5 @@
 - Connect the USB cable between the EVK and the PC for the console.
 (The USB console connector is the one close the push buttons)
 
-- Insert the micro SD card in the board, power it up and U-boot messages should
+- Insert the micro SD card in the board, power it up and U-Boot messages should
 come up.
diff --git a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
index b9b3573..98d5675 100644
--- a/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
+++ b/board/freescale/mx6ul_14x14_evk/mx6ul_14x14_evk.c
@@ -394,7 +394,7 @@
 
 	/*
 	 * According to the board_mmc_init() the following map is done:
-	 * (U-boot device node)    (Physical Port)
+	 * (U-Boot device node)    (Physical Port)
 	 * mmc0                    USDHC1
 	 * mmc1                    USDHC2
 	 */
diff --git a/board/freescale/mx7dsabresd/mx7dsabresd.c b/board/freescale/mx7dsabresd/mx7dsabresd.c
index 20e56f2..fee24e2 100644
--- a/board/freescale/mx7dsabresd/mx7dsabresd.c
+++ b/board/freescale/mx7dsabresd/mx7dsabresd.c
@@ -366,7 +366,7 @@
 	int i, ret;
 	/*
 	 * According to the board_mmc_init() the following map is done:
-	 * (U-boot device node)    (Physical Port)
+	 * (U-Boot device node)    (Physical Port)
 	 * mmc0                    USDHC1
 	 * mmc2                    USDHC3 (eMMC)
 	 */
diff --git a/board/freescale/p1010rdb/README.P1010RDB-PA b/board/freescale/p1010rdb/README.P1010RDB-PA
index cde246d..105942f 100644
--- a/board/freescale/p1010rdb/README.P1010RDB-PA
+++ b/board/freescale/p1010rdb/README.P1010RDB-PA
@@ -95,7 +95,7 @@
 instead of to CAN/UART1.
 
 
-Build and burn u-boot to NOR flash
+Build and burn U-Boot to NOR flash
 ==================================
 1. Build u-boot.bin image
 	export ARCH=powerpc
@@ -131,7 +131,7 @@
 1 - boot from lower 4 sectors
 
 
-Build and burn u-boot to NAND flash
+Build and burn U-Boot to NAND flash
 ===================================
 1. Build u-boot.bin image
 	export ARCH=powerpc
@@ -146,7 +146,7 @@
 3. Check SW4[1:4]= 1000 and SW6[4]=1, then power on.
 
 
-Build and burn u-boot to SPI flash
+Build and burn U-Boot to SPI flash
 ==================================
 1. Build u-boot-spi.bin image
 	make P1010RDB_SPIFLASH_config; make
diff --git a/board/freescale/p1010rdb/README.P1010RDB-PB b/board/freescale/p1010rdb/README.P1010RDB-PB
index c5d1419..dc82f0d 100644
--- a/board/freescale/p1010rdb/README.P1010RDB-PB
+++ b/board/freescale/p1010rdb/README.P1010RDB-PB
@@ -112,14 +112,14 @@
 
 To enable SDHC in case of NOR/NAND/SPI boot
    a) For temporary use case in runtime without reboot system
-      run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC.
+      run 'mux sdhc' in U-Boot to validate SDHC with invalidating IFC.
 
    b) For long-term use case
       set 'esdhc' in hwconfig and save it.
 
 To enable IFC in case of SD boot
    a) For temporary use case in runtime without reboot system
-      run 'mux ifc' in u-boot to validate IFC with invalidating SDHC.
+      run 'mux ifc' in U-Boot to validate IFC with invalidating SDHC.
 
    b) For long-term use case
       set 'ifc' in hwconfig and save it.
diff --git a/board/freescale/t102xqds/README b/board/freescale/t102xqds/README
index bb0f280..c00e3ba 100644
--- a/board/freescale/t102xqds/README
+++ b/board/freescale/t102xqds/README
@@ -172,16 +172,16 @@
 128MB NOR Flash memory Map
 --------------------------
 Start Address   End Address     Definition			Max size
-0xEFF40000      0xEFFFFFFF      u-boot (current bank)		768KB
-0xEFF20000      0xEFF3FFFF      u-boot env (current bank)	128KB
+0xEFF40000      0xEFFFFFFF      U-Boot (current bank)		768KB
+0xEFF20000      0xEFF3FFFF      U-Boot env (current bank)	128KB
 0xEFF00000      0xEFF1FFFF      FMAN Ucode (current bank)	128KB
 0xEFE00000      0xEFE3FFFF      QE firmware (current bank)	256KB
 0xED300000      0xEFEFFFFF      rootfs (alt bank)		44MB
 0xEC800000      0xEC8FFFFF      Hardware device tree (alt bank) 1MB
 0xEC020000      0xEC7FFFFF      Linux.uImage (alt bank)		7MB + 875KB
 0xEC000000      0xEC01FFFF      RCW (alt bank)			128KB
-0xEBF40000      0xEBFFFFFF      u-boot (alt bank)		768KB
-0xEBF20000      0xEBF3FFFF      u-boot env (alt bank)		128KB
+0xEBF40000      0xEBFFFFFF      U-Boot (alt bank)		768KB
+0xEBF20000      0xEBF3FFFF      U-Boot env (alt bank)		128KB
 0xEBF00000      0xEBF1FFFF      FMAN ucode (alt bank)		128KB
 0xEBE00000      0xEBE3FFFF      QE firmware (alt bank)		256KB
 0xE9300000      0xEBEFFFFF      rootfs (current bank)		44MB
@@ -221,11 +221,11 @@
 
    Switching between default bank0 and alternate bank4 on NOR flash
    To change boot source to vbank4:
-	via software:   run command 'qixis_reset altbank' in u-boot.
+	via software:   run command 'qixis_reset altbank' in U-Boot.
 	via DIP-switch: set SW6[1:4] = '0100'
 
    To change boot source to vbank0:
-	via software:   run command 'qixis_reset' in u-boot.
+	via software:   run command 'qixis_reset' in U-Boot.
 	via DIP-Switch: set SW6[1:4] = '0000'
 
 2. NAND Boot:
@@ -273,8 +273,8 @@
 -------------------------------
 PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
 SPL further initializes DDR using SPD and environment variables
-and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
-Finally SPL transers control to u-boot for futher booting.
+and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to U-Boot for futher booting.
 
 SPL has following features:
  - Executes within 256K
@@ -294,14 +294,14 @@
 -------------------------------------------------
 |STACK		   | 0xFFFD8000 (22KB)		|
 -------------------------------------------------
-|U-boot SPL	   | 0xFFFD8000 (160KB)		|
+|U-Boot SPL	   | 0xFFFD8000 (160KB)		|
 -------------------------------------------------
 
 NAND Flash memory Map on T1024QDS
 -------------------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot		1MB
-0x100000	0x15FFFF	u-boot env	8KB
+0x000000	0x0FFFFF	U-Boot		1MB
+0x100000	0x15FFFF	U-Boot env	8KB
 0x160000	0x17FFFF	FMAN Ucode	128KB
 0x180000	0x19FFFF	QE Firmware	128KB
 
@@ -309,8 +309,8 @@
 SD Card memory Map on T1024QDS
 ----------------------------------------------------
 Block		#blocks		Definition	Size
-0x008		2048		u-boot img	1MB
-0x800		0016		u-boot env	8KB
+0x008		2048		U-Boot img	1MB
+0x800		0016		U-Boot env	8KB
 0x820		0256		FMAN Ucode	128KB
 0x920		0256		QE Firmware	128KB
 
@@ -318,8 +318,8 @@
 SPI Flash memory Map on T1024QDS
 ----------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot img	1MB
-0x100000	0x101FFF	u-boot env	8KB
+0x000000	0x0FFFFF	U-Boot img	1MB
+0x100000	0x101FFF	U-Boot env	8KB
 0x110000	0x12FFFF	FMAN Ucode	128KB
 0x130000	0x14FFFF	QE Firmware	128KB
 
diff --git a/board/freescale/t102xqds/eth_t102xqds.c b/board/freescale/t102xqds/eth_t102xqds.c
index ca54e2a..19543c0 100644
--- a/board/freescale/t102xqds/eth_t102xqds.c
+++ b/board/freescale/t102xqds/eth_t102xqds.c
@@ -310,7 +310,7 @@
 	case 0x95:
 	case 0x99:
 		/*
-		 * XFI does not need a PHY to work, but to avoid U-boot use
+		 * XFI does not need a PHY to work, but to avoid U-Boot use
 		 * default PHY address which is zero to a MAC when it found
 		 * a MAC has no PHY address, we give a PHY address to XFI
 		 * MAC, and should not use a real XAUI PHY address, since
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
index 7d3794a..a0af25a 100644
--- a/board/freescale/t102xrdb/README
+++ b/board/freescale/t102xrdb/README
@@ -145,8 +145,8 @@
 128MB NOR Flash Memory Layout
 -----------------------------
 Start Address   End Address     Definition			Max size
-0xEFF40000      0xEFFFFFFF      u-boot (current bank)		768KB
-0xEFF20000      0xEFF3FFFF      u-boot env (current bank)	128KB
+0xEFF40000      0xEFFFFFFF      U-Boot (current bank)		768KB
+0xEFF20000      0xEFF3FFFF      U-Boot env (current bank)	128KB
 0xEFF00000      0xEFF1FFFF      FMAN Ucode (current bank)	128KB
 0xEFE00000      0xEFE3FFFF      QE firmware (current bank)	256KB
 0xED300000      0xEFDFFFFF      rootfs (alt bank)		44MB
@@ -158,8 +158,8 @@
 0xEC700000	0xEC7FFFFF	HV.uImage (alternate bank)	1MB
 0xEC020000      0xEC6FFFFF      Linux.uImage (alt bank)		~7MB
 0xEC000000      0xEC01FFFF      RCW (alt bank)			128KB
-0xEBF40000      0xEBFFFFFF      u-boot (alt bank)		768KB
-0xEBF20000      0xEBF3FFFF      u-boot env (alt bank)		128KB
+0xEBF40000      0xEBFFFFFF      U-Boot (alt bank)		768KB
+0xEBF20000      0xEBF3FFFF      U-Boot env (alt bank)		128KB
 0xEBF00000      0xEBF1FFFF      FMAN ucode (alt bank)		128KB
 0xEBE00000      0xEBE3FFFF      QE firmware (alt bank)		256KB
 0xE9300000      0xEBDFFFFF      rootfs (current bank)		44MB
@@ -198,18 +198,18 @@
    Switching between default bank0 and alternate bank4 on NOR flash
    To change boot source to vbank4:
    on T1024RDB:
-	via software:   run command 'cpld reset altbank' in u-boot.
+	via software:   run command 'cpld reset altbank' in U-Boot.
 	via DIP-switch: set SW3[5:7] = '100'
    on T1023RDB:
-	via software:   run command 'switch bank4' in u-boot.
+	via software:   run command 'switch bank4' in U-Boot.
 	via DIP-switch: set SW3[5:7] = '100'
 
    To change boot source to vbank0:
    on T1024RDB:
-	via software:   run command 'cpld reset' in u-boot.
+	via software:   run command 'cpld reset' in U-Boot.
 	via DIP-Switch: set SW3[5:7] = '000'
    on T1023RDB:
-	via software:   run command 'switch bank0' in u-boot.
+	via software:   run command 'switch bank0' in U-Boot.
 	via DIP-switch: set SW3[5:7] = '000'
 
 2. NAND Boot:
@@ -255,8 +255,8 @@
 -------------------------------
 PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
 SPL further initializes DDR using SPD and environment variables
-and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
-Finally SPL transers control to u-boot for futher booting.
+and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to U-Boot for futher booting.
 
 SPL has following features:
  - Executes within 256K
@@ -276,14 +276,14 @@
 -------------------------------------------------
 |STACK		   | 0xFFFD8000 (22KB)		|
 -------------------------------------------------
-|U-boot SPL	   | 0xFFFD8000 (160KB)		|
+|U-Boot SPL	   | 0xFFFD8000 (160KB)		|
 -------------------------------------------------
 
 NAND Flash memory Map on T1024RDB
 -------------------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot		1MB(2 block)
-0x100000	0x17FFFF	u-boot env	512KB(1 block)
+0x000000	0x0FFFFF	U-Boot		1MB(2 block)
+0x100000	0x17FFFF	U-Boot env	512KB(1 block)
 0x180000	0x1FFFFF	FMAN Ucode	512KB(1 block)
 0x200000	0x27FFFF	QE Firmware	512KB(1 block)
 
@@ -291,16 +291,16 @@
 NAND Flash memory Map on T1023RDB
 ----------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot		1MB
-0x100000	0x15FFFF	u-boot env	8KB
+0x000000	0x0FFFFF	U-Boot		1MB
+0x100000	0x15FFFF	U-Boot env	8KB
 0x160000	0x17FFFF	FMAN Ucode	128KB
 
 
 SD Card memory Map on T102xRDB
 ----------------------------------------------------
 Block		#blocks		Definition	Size
-0x008		2048		u-boot img	1MB
-0x800		0016		u-boot env	8KB
+0x008		2048		U-Boot img	1MB
+0x800		0016		U-Boot env	8KB
 0x820		0256		FMAN Ucode	128KB
 0x920		0256		QE Firmware	128KB(only T1024RDB)
 
@@ -308,8 +308,8 @@
 64MB SPI Flash memory Map on T102xRDB
 ----------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot img	1MB
-0x100000	0x101FFF	u-boot env	8KB
+0x000000	0x0FFFFF	U-Boot img	1MB
+0x100000	0x101FFF	U-Boot env	8KB
 0x110000	0x12FFFF	FMAN Ucode	128KB
 0x130000	0x14FFFF	QE Firmware	128KB(only T1024RDB)
 0x300000	0x3FFFFF	device tree	128KB
diff --git a/board/freescale/t1040qds/README b/board/freescale/t1040qds/README
index 8160ca0..6c5ffc0 100644
--- a/board/freescale/t1040qds/README
+++ b/board/freescale/t1040qds/README
@@ -118,15 +118,15 @@
 NOR Flash memory Map on T1040QDS
 --------------------------------
  Start          End             Definition                       Size
-0xEFF40000      0xEFFFFFFF      u-boot (current bank)            768KB
-0xEFF20000      0xEFF3FFFF      u-boot env (current bank)        128KB
+0xEFF40000      0xEFFFFFFF      U-Boot (current bank)            768KB
+0xEFF20000      0xEFF3FFFF      U-Boot env (current bank)        128KB
 0xEFF00000      0xEFF1FFFF      FMAN Ucode (current bank)        128KB
 0xED300000      0xEFEFFFFF      rootfs (alt bank)                44MB
 0xEC800000      0xEC8FFFFF      Hardware device tree (alt bank)  1MB
 0xEC020000      0xEC7FFFFF      Linux.uImage (alt bank)          7MB + 875KB
 0xEC000000      0xEC01FFFF      RCW (alt bank)                   128KB
-0xEBF40000      0xEBFFFFFF      u-boot (alt bank)                768KB
-0xEBF20000      0xEBF3FFFF      u-boot env (alt bank)            128KB
+0xEBF40000      0xEBFFFFFF      U-Boot (alt bank)                768KB
+0xEBF20000      0xEBF3FFFF      U-Boot env (alt bank)            128KB
 0xEBF00000      0xEBF1FFFF      FMAN ucode (alt bank)            128KB
 0xE9300000      0xEBEFFFFF      rootfs (current bank)            44MB
 0xE8800000      0xE88FFFFF      Hardware device tree (cur bank)  11MB + 512KB
@@ -138,7 +138,7 @@
 --------------------------------------------------------------
 The below commands apply to T1040QDS
 
-1. U-boot environment variable hwconfig
+1. U-Boot environment variable hwconfig
    The default hwconfig is:
 	hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1:
 					dr_mode=host,phy_type=utmi
diff --git a/board/freescale/t104xrdb/README b/board/freescale/t104xrdb/README
index b9d2212..98b3f63 100644
--- a/board/freescale/t104xrdb/README
+++ b/board/freescale/t104xrdb/README
@@ -186,15 +186,15 @@
 NOR Flash memory Map
 ---------------------
  Start          End             Definition                       Size
-0xEFF40000      0xEFFFFFFF      u-boot (current bank)            768KB
-0xEFF20000      0xEFF3FFFF      u-boot env (current bank)        128KB
+0xEFF40000      0xEFFFFFFF      U-Boot (current bank)            768KB
+0xEFF20000      0xEFF3FFFF      U-Boot env (current bank)        128KB
 0xEFF00000      0xEFF1FFFF      FMAN Ucode (current bank)        128KB
 0xED300000      0xEFEFFFFF      rootfs (alt bank)                44MB
 0xEC800000      0xEC8FFFFF      Hardware device tree (alt bank)  1MB
 0xEC020000      0xEC7FFFFF      Linux.uImage (alt bank)          7MB + 875KB
 0xEC000000      0xEC01FFFF      RCW (alt bank)                   128KB
-0xEBF40000      0xEBFFFFFF      u-boot (alt bank)                768KB
-0xEBF20000      0xEBF3FFFF      u-boot env (alt bank)            128KB
+0xEBF40000      0xEBFFFFFF      U-Boot (alt bank)                768KB
+0xEBF20000      0xEBF3FFFF      U-Boot env (alt bank)            128KB
 0xEBF00000      0xEBF1FFFF      FMAN ucode (alt bank)            128KB
 0xE9300000      0xEBEFFFFF      rootfs (current bank)            44MB
 0xE8800000      0xE88FFFFF      Hardware device tree (cur bank)  11MB + 512KB
@@ -206,7 +206,7 @@
 --------------------------------------------------------------
 The below commands apply to the board
 
-1. U-boot environment variable hwconfig
+1. U-Boot environment variable hwconfig
    The default hwconfig is:
 	hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1:
 					dr_mode=host,phy_type=utmi
@@ -228,8 +228,8 @@
 ----------------------------------
 PBL initialise the internal SRAM and copy SPL(160KB) in SRAM.
 SPL further initialise DDR using SPD and environment variables and copy
-u-boot(768 KB) from flash to DDR.
-Finally SPL transer control to u-boot for futher booting.
+U-Boot(768 KB) from flash to DDR.
+Finally SPL transer control to U-Boot for futher booting.
 
 SPL has following features:
  - Executes within 256K
@@ -250,30 +250,30 @@
  -----------------------------------------------
  STACK       | 0xFFFD8000 (22KB)               |
  -----------------------------------------------
- U-boot SPL  | 0xFFFD8000 (160KB)              |
+ U-Boot SPL  | 0xFFFD8000 (160KB)              |
  -----------------------------------------------
 
 NAND Flash memory Map on T104xRDB
 ------------------------------------------
  Start		 End		Definition			Size
-0x000000	0x0FFFFF	u-boot                          1MB
-0x180000	0x19FFFF	u-boot env                      128KB
+0x000000	0x0FFFFF	U-Boot                          1MB
+0x180000	0x19FFFF	U-Boot env                      128KB
 0x280000	0x29FFFF	FMAN Ucode                      128KB
 0x380000	0x39FFFF	QE Firmware                     128KB
 
 SD Card memory Map on T104xRDB
 ------------------------------------------
  Block		#blocks		Definition			Size
-0x008		2048		u-boot                          1MB
-0x800		0024		u-boot env                      8KB
+0x008		2048		U-Boot                          1MB
+0x800		0024		U-Boot env                      8KB
 0x820		0256		FMAN Ucode                      128KB
 0x920		0256		QE Firmware                     128KB
 
 SPI Flash memory Map on T104xRDB
 ------------------------------------------
  Start		 End		Definition			Size
-0x000000	0x0FFFFF	u-boot                          1MB
-0x100000	0x101FFF	u-boot env                      8KB
+0x000000	0x0FFFFF	U-Boot                          1MB
+0x100000	0x101FFF	U-Boot env                      8KB
 0x110000	0x12FFFF	FMAN Ucode                      128KB
 0x130000	0x14FFFF	QE Firmware                     128KB
 
diff --git a/board/freescale/t208xqds/README b/board/freescale/t208xqds/README
index 83060c1..2a2a0e5 100755
--- a/board/freescale/t208xqds/README
+++ b/board/freescale/t208xqds/README
@@ -92,7 +92,7 @@
  10GBASE-KR scenario.
  So, for XFI usage, there are two scenarios, one will use fiber cable,
  another will use copper cable. An hwconfig env "fsl_10gkr_copper" is
- introduced to indicate a XFI port will use copper cable, and U-boot
+ introduced to indicate a XFI port will use copper cable, and U-Boot
  will fixup the dtb accordingly.
  It's used as: fsl_10gkr_copper:<10g_mac_name>
  The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4, they
@@ -108,7 +108,7 @@
  - T2080QDS can support 1G-KX by using SGMII protocol, but serdes lane
  runs in 1G-KX mode. By default, the lane runs in SGMII mode, to set a lane
  in 1G-KX mode, need to set corresponding bit in SerDes Protocol Configuration
- Register 1 (PCCR1), and U-boot fixup the dtb for kernel to do proper
+ Register 1 (PCCR1), and U-Boot fixup the dtb for kernel to do proper
  initialization.
  Hwconfig "fsl_1gkx" is used to indicate a lane runs in 1G-KX mode, MAC
  1/2/5/6/9/10 are available for 1G-KX, MAC 3/4 run in RGMII mode. To set a
@@ -142,15 +142,15 @@
 128M NOR Flash memory Map
 -------------------------
 Start Address   End Address	Definition			Max size
-0xEFF40000	0xEFFFFFFF	u-boot (current bank)		768KB
-0xEFF20000	0xEFF3FFFF	u-boot env (current bank)	128KB
+0xEFF40000	0xEFFFFFFF	U-Boot (current bank)		768KB
+0xEFF20000	0xEFF3FFFF	U-Boot env (current bank)	128KB
 0xEFF00000	0xEFF1FFFF	FMAN Ucode (current bank)	128KB
 0xED300000	0xEFEFFFFF	rootfs (alt bank)		44MB
 0xEC800000	0xEC8FFFFF	Hardware device tree (alt bank)	1MB
 0xEC020000	0xEC7FFFFF	Linux.uImage (alt bank)		7MB + 875KB
 0xEC000000	0xEC01FFFF	RCW (alt bank)			128KB
-0xEBF40000	0xEBFFFFFF	u-boot (alt bank)		768KB
-0xEBF20000	0xEBF3FFFF	u-boot env (alt bank)		128KB
+0xEBF40000	0xEBFFFFFF	U-Boot (alt bank)		768KB
+0xEBF20000	0xEBF3FFFF	U-Boot env (alt bank)		128KB
 0xEBF00000	0xEBF1FFFF	FMAN ucode (alt bank)		128KB
 0xE9300000	0xEBEFFFFF	rootfs (current bank)		44MB
 0xE8800000	0xE88FFFFF	Hardware device tree (cur bank)	1MB
@@ -172,11 +172,11 @@
 
    Switching between default bank0 and alternate bank4 on NOR flash
    To change boot source to vbank4:
-	by software:   run command 'qixis_reset altbank' in u-boot.
+	by software:   run command 'qixis_reset altbank' in U-Boot.
 	by DIP-switch: set SW6[1:4] = '0100'
 
    To change boot source to vbank0:
-	by software:   run command 'qixis_reset' in u-boot.
+	by software:   run command 'qixis_reset' in U-Boot.
 	by DIP-Switch: set SW6[1:4] = '0000'
 
 2. NAND Boot:
@@ -216,8 +216,8 @@
 -------------------------------
 PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
 SPL further initializes DDR using SPD and environment variables
-and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
-Finally SPL transers control to u-boot for futher booting.
+and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to U-Boot for futher booting.
 
 SPL has following features:
  - Executes within 256K
@@ -237,30 +237,30 @@
 -------------------------------------------------
 |STACK		   | 0xFFFD8000 (22KB)		|
 -------------------------------------------------
-|U-boot SPL	   | 0xFFFD8000 (160KB)		|
+|U-Boot SPL	   | 0xFFFD8000 (160KB)		|
 -------------------------------------------------
 
 NAND Flash memory Map on T2080QDS
 --------------------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot img	1MB  (2 blocks)
-0x100000	0x17FFFF	u-boot env	512KB (1 block)
+0x000000	0x0FFFFF	U-Boot img	1MB  (2 blocks)
+0x100000	0x17FFFF	U-Boot env	512KB (1 block)
 0x180000	0x1FFFFF	FMAN ucode	512KB (1 block)
 
 
 Micro SD Card memory Map on T2080QDS
 ----------------------------------------------------
 Block		#blocks		Definition	Size
-0x008		2048		u-boot img	1MB
-0x800		0016		u-boot env	8KB
+0x008		2048		U-Boot img	1MB
+0x800		0016		U-Boot env	8KB
 0x820		0128		FMAN ucode	64KB
 
 
 SPI Flash memory Map on T2080QDS
 ----------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot img	1MB
-0x100000	0x101FFF	u-boot env	8KB
+0x000000	0x0FFFFF	U-Boot img	1MB
+0x100000	0x101FFF	U-Boot env	8KB
 0x110000	0x11FFFF	FMAN ucode	64KB
 
 
diff --git a/board/freescale/t208xqds/eth_t208xqds.c b/board/freescale/t208xqds/eth_t208xqds.c
index f08cff2..e92b5d3 100644
--- a/board/freescale/t208xqds/eth_t208xqds.c
+++ b/board/freescale/t208xqds/eth_t208xqds.c
@@ -600,7 +600,7 @@
 	case 0x66:
 	case 0x67:
 		/*
-		 * XFI does not need a PHY to work, but to avoid U-boot use
+		 * XFI does not need a PHY to work, but to avoid U-Boot use
 		 * default PHY address which is zero to a MAC when it found
 		 * a MAC has no PHY address, we give a PHY address to XFI
 		 * MAC, and should not use a real XAUI PHY address, since
diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README
index 24484cd..42b2b92 100644
--- a/board/freescale/t208xrdb/README
+++ b/board/freescale/t208xrdb/README
@@ -107,16 +107,16 @@
 128M NOR Flash memory Map
 -------------------------
 Start Address   End Address	Definition			Max size
-0xEFF40000	0xEFFFFFFF	u-boot (current bank)		768KB
-0xEFF20000	0xEFF3FFFF	u-boot env (current bank)	128KB
+0xEFF40000	0xEFFFFFFF	U-Boot (current bank)		768KB
+0xEFF20000	0xEFF3FFFF	U-Boot env (current bank)	128KB
 0xEFF00000	0xEFF1FFFF	FMAN Ucode (current bank)	128KB
 0xEFE00000	0xEFE3FFFF	PHY CS4315 firmware		256KB
 0xED300000	0xEFEFFFFF	rootfs (alt bank)		44MB
 0xEC800000	0xEC8FFFFF	Hardware device tree (alt bank)	1MB
 0xEC020000	0xEC7FFFFF	Linux.uImage (alt bank)		7MB + 875KB
 0xEC000000	0xEC01FFFF	RCW (alt bank)			128KB
-0xEBF40000	0xEBFFFFFF	u-boot (alt bank)		768KB
-0xEBF20000	0xEBF3FFFF	u-boot env (alt bank)		128KB
+0xEBF40000	0xEBFFFFFF	U-Boot (alt bank)		768KB
+0xEBF20000	0xEBF3FFFF	U-Boot env (alt bank)		128KB
 0xEBF00000	0xEBF1FFFF	FMAN ucode (alt bank)		128KB
 0xEBE00000	0xEBE3FFFF	PHY CS4315 firmware (alt bank)	256KB
 0xE9300000	0xEBEFFFFF	rootfs (current bank)		44MB
@@ -155,11 +155,11 @@
 
    Switching between default bank and alternate bank on NOR flash
    To change boot source to vbank4:
-	via software:   run command 'cpld reset altbank' in u-boot.
+	via software:   run command 'cpld reset altbank' in U-Boot.
 	via DIP-switch: set SW3[5:7] = '100'
 
    To change boot source to vbank0:
-	via software:   run command 'cpld reset' in u-boot.
+	via software:   run command 'cpld reset' in U-Boot.
 	via DIP-Switch: set SW3[5:7] = '000'
 
 2. NAND Boot:
@@ -197,8 +197,8 @@
 -------------------------------
 PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
 SPL further initializes DDR using SPD and environment variables
-and copy u-boot(768 KB) from NAND/SPI/SD device to DDR.
-Finally SPL transers control to u-boot for futher booting.
+and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR.
+Finally SPL transers control to U-Boot for futher booting.
 
 SPL has following features:
  - Executes within 256K
@@ -218,14 +218,14 @@
 -------------------------------------------------
 |STACK		   | 0xFFFD8000 (22KB)		|
 -------------------------------------------------
-|U-boot SPL	   | 0xFFFD8000 (160KB)		|
+|U-Boot SPL	   | 0xFFFD8000 (160KB)		|
 -------------------------------------------------
 
 NAND Flash memory Map on T2080RDB
 --------------------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot img	1MB  (2 blocks)
-0x100000	0x17FFFF	u-boot env	512KB (1 block)
+0x000000	0x0FFFFF	U-Boot img	1MB  (2 blocks)
+0x100000	0x17FFFF	U-Boot env	512KB (1 block)
 0x180000	0x1FFFFF	FMAN ucode	512KB (1 block)
 0x200000	0x27FFFF	CS4315 ucode	512KB (1 block)
 
@@ -233,8 +233,8 @@
 Micro SD Card memory Map on T2080RDB
 ----------------------------------------------------
 Block		#blocks		Definition	Size
-0x008		2048		u-boot img	1MB
-0x800		0016		u-boot env	8KB
+0x008		2048		U-Boot img	1MB
+0x800		0016		U-Boot env	8KB
 0x820		0128		FMAN ucode	64KB
 0x8a0		0512		CS4315 ucode	256KB
 
@@ -242,8 +242,8 @@
 SPI Flash memory Map on T2080RDB
 ----------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot img	1MB
-0x100000	0x101FFF	u-boot env	8KB
+0x000000	0x0FFFFF	U-Boot img	1MB
+0x100000	0x101FFF	U-Boot env	8KB
 0x110000	0x11FFFF	FMAN ucode	64KB
 0x120000        0x15FFFF        CS4315 ucode	256KB
 
diff --git a/board/freescale/t4qds/README b/board/freescale/t4qds/README
index 3962fee..bf23814 100644
--- a/board/freescale/t4qds/README
+++ b/board/freescale/t4qds/README
@@ -86,7 +86,7 @@
 	10GBASE-KR scenario.
 	So, for XFI usage, there are two scenarios, one will use fiber cable,
 	another will use copper cable. An hwconfig env "fsl_10gkr_copper" is
-	introduced to indicate a XFI port will use copper cable, and U-boot
+	introduced to indicate a XFI port will use copper cable, and U-Boot
 	will fixup the dtb accordingly.
 	It's used as: fsl_10gkr_copper:<10g_mac_name>
 	The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm2_10g1, fm2_10g2, they
@@ -118,7 +118,7 @@
 
 Voltage ID and VDD override
 --------------------
-T4240 has a VID feature. U-boot reads the VID efuses and adjust the voltage
+T4240 has a VID feature. U-Boot reads the VID efuses and adjust the voltage
 accordingly. The voltage can also be override by command vdd_override. The
 syntax is
 
@@ -144,8 +144,8 @@
 -------------------------------
 PBL initializes the internal SRAM and copy SPL(160K) in SRAM.
 SPL further initialise DDR using SPD and environment variables
-and copy u-boot(768 KB) from NAND/SD device to DDR.
-Finally SPL transers control to u-boot for futher booting.
+and copy U-Boot(768 KB) from NAND/SD device to DDR.
+Finally SPL transers control to U-Boot for futher booting.
 
 SPL has following features:
  - Executes within 256K
@@ -165,21 +165,21 @@
 -------------------------------------------------
 |STACK		| 0xFFFD8000	(22KB)		|
 -------------------------------------------------
-|U-boot SPL	| 0xFFFD8000 	(160KB)		|
+|U-Boot SPL	| 0xFFFD8000 	(160KB)		|
 -------------------------------------------------
 
 NAND Flash memory Map on T4QDS
 --------------------------------------------------------------
 Start		End		Definition	Size
-0x000000	0x0FFFFF	u-boot img	1MB
-0x140000	0x15FFFF	u-boot env      128KB
+0x000000	0x0FFFFF	U-Boot img	1MB
+0x140000	0x15FFFF	U-Boot env      128KB
 0x160000	0x17FFFF	FMAN Ucode      128KB
 
 Micro SD Card memory Map on T4QDS
 ----------------------------------------------------
 Block		#blocks		Definition	Size
-0x008		2048		u-boot img	1MB
-0x800		0016		u-boot env	8KB
+0x008		2048		U-Boot img	1MB
+0x800		0016		U-Boot env	8KB
 0x820		0128		FMAN ucode	64KB
 
 Switch Settings: (ON is 1, OFF is 0)
diff --git a/board/freescale/t4qds/eth.c b/board/freescale/t4qds/eth.c
index 83a3a9b..95f8c04 100644
--- a/board/freescale/t4qds/eth.c
+++ b/board/freescale/t4qds/eth.c
@@ -658,7 +658,7 @@
 		switch (fm_info_get_enet_if(i)) {
 		case PHY_INTERFACE_MODE_XGMII:
 			if ((srds_prtcl_s2 == 55) || (srds_prtcl_s2 == 57)) {
-				/* A fake PHY address to make U-boot happy */
+				/* A fake PHY address to make U-Boot happy */
 				fm_info_set_phy_address(i, i);
 			} else {
 				lane = serdes_get_first_lane(FSL_SRDS_1,
@@ -839,7 +839,7 @@
 		switch (fm_info_get_enet_if(i)) {
 		case PHY_INTERFACE_MODE_XGMII:
 			if ((srds_prtcl_s2 == 55) || (srds_prtcl_s2 == 57)) {
-				/* A fake PHY address to make U-boot happy */
+				/* A fake PHY address to make U-Boot happy */
 				fm_info_set_phy_address(i, i);
 			} else {
 				lane = serdes_get_first_lane(FSL_SRDS_2,