mx7: Remove BMODE support
i.MX7 does not support BMODE due to the erratum e10574 ("Watchdog:
A watchdog timeout or software trigger will not reset the SOC"), so
remove its support.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 3aec89d..a1566cc 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -46,7 +46,7 @@
config CMD_BMODE
bool "Support the 'bmode' command"
default y
- depends on ARCH_MX7 || ARCH_MX6 || ARCH_MX5
+ depends on ARCH_MX6 || ARCH_MX5
help
This enables the 'bmode' (bootmode) command for forcing
a boot from specific media.
diff --git a/arch/arm/mach-imx/mx7/Kconfig b/arch/arm/mach-imx/mx7/Kconfig
index 2a3db86..3d12874 100644
--- a/arch/arm/mach-imx/mx7/Kconfig
+++ b/arch/arm/mach-imx/mx7/Kconfig
@@ -50,7 +50,6 @@
config TARGET_COLIBRI_IMX7
bool "Support Colibri iMX7S/iMX7D modules"
- select BOARD_LATE_INIT
select DM
select DM_SERIAL
select DM_THERMAL
diff --git a/arch/arm/mach-imx/mx7/soc.c b/arch/arm/mach-imx/mx7/soc.c
index 2aca24b..7334ca9 100644
--- a/arch/arm/mach-imx/mx7/soc.c
+++ b/arch/arm/mach-imx/mx7/soc.c
@@ -8,7 +8,6 @@
#include <asm/arch/imx-regs.h>
#include <asm/arch/clock.h>
#include <asm/arch/sys_proto.h>
-#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/dma.h>
#include <asm/mach-imx/hab.h>
#include <asm/mach-imx/rdc-sema.h>
@@ -254,30 +253,6 @@
writew(reg, &wdog->wcr);
}
-/*
- * cfg_val will be used for
- * Boot_cfg4[7:0]:Boot_cfg3[7:0]:Boot_cfg2[7:0]:Boot_cfg1[7:0]
- * After reset, if GPR10[28] is 1, ROM will copy GPR9[25:0]
- * to SBMR1, which will determine the boot device.
- */
-const struct boot_mode soc_boot_modes[] = {
- {"ecspi1:0", MAKE_CFGVAL(0x00, 0x60, 0x00, 0x00)},
- {"ecspi1:1", MAKE_CFGVAL(0x40, 0x62, 0x00, 0x00)},
- {"ecspi1:2", MAKE_CFGVAL(0x80, 0x64, 0x00, 0x00)},
- {"ecspi1:3", MAKE_CFGVAL(0xc0, 0x66, 0x00, 0x00)},
-
- {"weim", MAKE_CFGVAL(0x00, 0x50, 0x00, 0x00)},
- {"qspi1", MAKE_CFGVAL(0x10, 0x40, 0x00, 0x00)},
- /* 4 bit bus width */
- {"usdhc1", MAKE_CFGVAL(0x10, 0x10, 0x00, 0x00)},
- {"usdhc2", MAKE_CFGVAL(0x10, 0x14, 0x00, 0x00)},
- {"usdhc3", MAKE_CFGVAL(0x10, 0x18, 0x00, 0x00)},
- {"mmc1", MAKE_CFGVAL(0x10, 0x20, 0x00, 0x00)},
- {"mmc2", MAKE_CFGVAL(0x10, 0x24, 0x00, 0x00)},
- {"mmc3", MAKE_CFGVAL(0x10, 0x28, 0x00, 0x00)},
- {NULL, 0},
-};
-
void s_init(void)
{
/* clock configuration. */