imx6: aristainetos: add support for rev C board
add support for revision C boards. This board has
no longer a NAND.
Signed-off-by: Heiko Schocher <hs@denx.de>
diff --git a/arch/arm/dts/imx6qdl-aristainetos2c.dtsi b/arch/arm/dts/imx6qdl-aristainetos2c.dtsi
new file mode 100644
index 0000000..ba13d55
--- /dev/null
+++ b/arch/arm/dts/imx6qdl-aristainetos2c.dtsi
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: (GPL-2.0)
+/*
+ * support for the imx6 based aristainetos2c board
+ *
+ * Copyright (C) 2019 Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2015 Heiko Schocher <hs@denx.de>
+ *
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+
+#include "imx6qdl-aristainetos2-common.dtsi"
+
+/ {
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio>;
+
+ LED_blue {
+ label = "led_blue";
+ gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_green {
+ label = "led_green";
+ gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_red {
+ label = "led_red";
+ gpios = <&gpio5 0 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_yellow {
+ label = "led_yellow";
+ gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+ };
+
+ LED_ena {
+ label = "led_ena";
+ gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH
+ &gpio4 10 GPIO_ACTIVE_HIGH
+ &gpio4 11 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+ pinctrl-assert-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
+ pinctrl-assert-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q128a11", "jedec,spi-nor";
+ spi-max-frequency = <20000000>;
+ reg = <0>;
+ };
+};
+
+&ecspi4 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH &gpio5 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ status = "okay";
+};
+
+&i2c1 {
+ tpm@20 {
+ compatible = "infineon,slb9645tt";
+ reg = <0x20>;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 20 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ bus-width = <8>;
+ no-1-8-v;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* SS0# */
+ MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x100b1
+ /* SS1# */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x100b1
+ /* SS2# */
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x100b1
+ /* WP pin NOR Flash */
+ MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x4001b0b0
+ /* Flash nReset */
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x4001b0b0
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+ MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x100b1 /* SS0# */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b1 /* SS1# */
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ /* led enable */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x4001b0b0
+ /* LCD power enable */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x4001b0b0
+ /* led yellow */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x4001b0b0
+ /* led red */
+ MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x4001b0b0
+ /* led green */
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x4001b0b0
+ /* led blue */
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x4001b0b0
+ /* Profibus IRQ */
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
+ /* FPGA IRQ currently unused*/
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0
+ /* Display reset because of clock failure */
+ MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x4001b0b0
+ /* spi bus #2 SS driver enable */
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x4001b0b0
+ /* RST_LOC# PHY reset input (has pull-down!)*/
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x4001b0b0
+ /* Touchscreen IRQ */
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0
+ /* PCIe reset */
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x4001b0b0
+ /* make sure pin is GPIO and not ENET_REF_CLK */
+ MX6QDL_PAD_GPIO_16__GPIO7_IO11 0x4001a0b0
+ /* TPM PP */
+ MX6QDL_PAD_EIM_A21__GPIO2_IO17 0x4001b0b0
+ /* TPM Reset */
+ MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x4001b0b0
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x1b0b0
+ MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
+ MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ /* SD1 card detect input */
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0
+ /* SD1 write protect input */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059
+ MX6QDL_PAD_NANDF_D4__SD2_DATA4 0x17059
+ MX6QDL_PAD_NANDF_D5__SD2_DATA5 0x17059
+ MX6QDL_PAD_NANDF_D6__SD2_DATA6 0x17059
+ MX6QDL_PAD_NANDF_D7__SD2_DATA7 0x17059
+ >;
+ };
+};