commit 6ebb4d09cfb61bd8ebe0234738feeea7c2b011b2
author Hans de Goede <hdegoede@redhat.com> Thu Aug 18 20:51:12 2016 +0200
committer Hans de Goede <hdegoede@redhat.com> Fri Aug 26 16:58:36 2016 +0200
tree eb92453773199d5077ced5b2fa53f3c79769ba67
parent 60ff992d2851a9b91687fd79cf28e674b12ee032

sunxi: Sync dts files with upstream kernel

Sync dts files with the current (Aug 18th 2016) state of Maxime's
linux/sunxi/for-next repo.

Note this commit also updates configs/MSI_Primo81_defconfig,
adding: "# CONFIG_REQUIRE_SERIAL_CONSOLE is not set", this is necessary
because the tablet does not have a reachable uart so the dts sync
drops its serial0 alias.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>

arch/arm/dts/sun8i-q8-common.dtsi

diff --git a/arch/arm/dts/sun8i-q8-common.dtsi b/arch/arm/dts/sun8i-q8-common.dtsi
index 346a49d..8e2cc30 100644
--- a/arch/arm/dts/sun8i-q8-common.dtsi
+++ b/arch/arm/dts/sun8i-q8-common.dtsi
@@ -39,140 +39,83 @@
  *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
-#include "sunxi-q8-common.dtsi"
-
-#include <dt-bindings/pwm/pwm.h>
+#include "sunxi-reference-design-tablet.dtsi"
+#include "sun8i-reference-design-tablet.dtsi"
 
 / {
 	aliases {
 		serial0 = &r_uart;
+		/* Make u-boot set mac-address for wifi without an eeprom */
+		ethernet0 = &sdio_wifi;
 	};
 
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&bl_en_pin_q8>;
-		pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
-		brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
-		default-brightness-level = <8>;
-		enable-gpios = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */
+	q8_hardwaremgr {
+		compatible = "allwinner,sunxi-q8-hardwaremgr";
+		touchscreen-i2c-bus = <&i2c0>;
+		touchscreen-supply = <&reg_ldo_io1>;
+		touchscreen-power-gpios = <&pio 7 1 GPIO_ACTIVE_HIGH>; /* PH1 */
 	};
 
-	chosen {
-		stdout-path = "serial0:115200n8";
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		/*
+		 * Q8 boards use various PL# pins as wifi-en. On other boards
+		 * these may be connected to a wifi module output pin. To avoid
+		 * short-circuits we configure these as inputs with pull-ups via
+		 * pinctrl, instead of listing them as active-low reset-gpios.
+		 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_pwrseq_pin_q8>;
+		/* The esp8089 needs 200 ms after driving wifi-en high */
+		post-power-on-delay-ms = <200>;
 	};
 };
 
+&ehci0 {
+	status  = "okay";
+};
+
-&mmc0 {
+&mmc1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_q8>;
-	vmmc-supply = <&reg_dcdc1>;
+	pinctrl-0 = <&mmc1_pins_a>;
+	vmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
 	bus-width = <4>;
-	cd-gpios = <&pio 1 4 GPIO_ACTIVE_HIGH>; /* PB4 */
-	cd-inverted;
+	non-removable;
 	status = "okay";
-};
 
-&pio {
-	bl_en_pin_q8: bl_en_pin@0 {
-		allwinner,pins = "PH6";
-		allwinner,function = "gpio_in";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	sdio_wifi: sdio_wifi@1 {
+		reg = <1>;
 	};
+};
 
-	mmc0_cd_pin_q8: mmc0_cd_pin@0 {
-		allwinner,pins = "PB4";
+&mmc1_pins_a {
+	allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+};
+
+&r_pio {
+	wifi_pwrseq_pin_q8: wifi_pwrseq_pin@0 {
+		allwinner,pins = "PL6", "PL7", "PL11";
 		allwinner,function = "gpio_in";
 		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
 		allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
 	};
 };
 
-&r_rsb {
-	status = "okay";
-
-	axp22x: pmic@3a3 {
-		compatible = "x-powers,axp223";
-		reg = <0x3a3>;
-		interrupt-parent = <&nmi_intc>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		eldoin-supply = <&reg_dcdc1>;
-	};
+&usbphy {
+	usb1_vbus-supply = <&reg_dldo1>;
 };
 
-#include "axp22x.dtsi"
-
-&reg_aldo1 {
-	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "vcc-io";
-};
-
-&reg_aldo2 {
-	regulator-always-on;
-	regulator-min-microvolt = <2350000>;
-	regulator-max-microvolt = <2650000>;
-	regulator-name = "vdd-dll";
+&gsl1680 {
+	touchscreen-size-x = <1024>;
+	touchscreen-size-y = <600>;
+	touchscreen-fw-name = "silead/gsl1680-q8-700.fw";
+	status = "okay";
 };
 
-&reg_aldo3 {
-	regulator-always-on;
-	regulator-min-microvolt = <2700000>;
+&reg_ldo_io1 {
+	regulator-min-microvolt = <3300000>;
 	regulator-max-microvolt = <3300000>;
-	regulator-name = "vcc-pll-avcc";
-};
-
-&reg_dc1sw {
-	regulator-name = "vcc-lcd";
-};
-
-&reg_dc5ldo {
-	regulator-always-on;
-	regulator-min-microvolt = <900000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-cpus";
-};
-
-&reg_dcdc1 {
-	regulator-always-on;
-	regulator-min-microvolt = <3000000>;
-	regulator-max-microvolt = <3000000>;
-	regulator-name = "vcc-3v0";
-};
-
-&reg_dcdc2 {
-	regulator-always-on;
-	regulator-min-microvolt = <900000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-sys";
-};
-
-&reg_dcdc3 {
-	regulator-always-on;
-	regulator-min-microvolt = <900000>;
-	regulator-max-microvolt = <1400000>;
-	regulator-name = "vdd-cpu";
-};
-
-&reg_dcdc5 {
-	regulator-always-on;
-	regulator-min-microvolt = <1500000>;
-	regulator-max-microvolt = <1500000>;
-	regulator-name = "vcc-dram";
-};
-
-&reg_rtc_ldo {
-	regulator-name = "vcc-rtc";
-};
-
-&r_uart {
-	pinctrl-names = "default";
-	pinctrl-0 = <&r_uart_pins_a>;
+	regulator-name = "vcc-touchscreen";
 	status = "okay";
 };
-
-&simplefb_lcd {
-	vcc-lcd-supply = <&reg_dc1sw>;
-};