net: dwc_eth_qos: Add support for st, ext-phyclk property
The "st,ext-phyclk" property is a unification of "st,eth-clk-sel"
and "st,eth-ref-clk-sel" properties. All three properties define
ETH CK clock direction, however:
- "st,eth-clk-sel" selects clock direction for GMII/RGMII mode
- "st,eth-ref-clk-sel" selects clock direction for RMII mode
- "st,ext-phyclk" selects clock direction for all RMII/GMII/RGMII modes
The "st,ext-phyclk" is the preferrable property to use.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Christophe ROULLIER <christophe.roullier@foss.st.com>
diff --git a/drivers/net/dwc_eth_qos_stm32.c b/drivers/net/dwc_eth_qos_stm32.c
index 435473f..9ee82b5 100644
--- a/drivers/net/dwc_eth_qos_stm32.c
+++ b/drivers/net/dwc_eth_qos_stm32.c
@@ -140,6 +140,8 @@
const bool is_mp13 = device_is_compatible(dev, "st,stm32mp13-dwmac");
/* Gigabit Ethernet 125MHz clock selection. */
const bool eth_clk_sel = dev_read_bool(dev, "st,eth-clk-sel");
+ /* Ethernet clock source is RCC. */
+ const bool ext_phyclk = dev_read_bool(dev, "st,ext-phyclk");
struct regmap *regmap;
u32 regmap_mask;
u32 value;
@@ -156,6 +158,12 @@
dev_dbg(dev, "PHY_INTERFACE_MODE_MII\n");
value = FIELD_PREP(SYSCFG_PMCSETR_ETH_SEL_MASK,
SYSCFG_PMCSETR_ETH_SEL_GMII_MII);
+ /*
+ * STM32MP15xx supports both MII and GMII, STM32MP13xx MII only.
+ * SYSCFG_PMCSETR ETH_SELMII is present only on STM32MP15xx and
+ * acts as a selector between 0:GMII and 1:MII. As STM32MP13xx
+ * supports only MII, ETH_SELMII is not present.
+ */
if (!is_mp13) /* Select MII mode on STM32MP15xx */
value |= SYSCFG_PMCSETR_ETH_SELMII;
break;
@@ -163,14 +171,25 @@
dev_dbg(dev, "PHY_INTERFACE_MODE_GMII\n");
value = FIELD_PREP(SYSCFG_PMCSETR_ETH_SEL_MASK,
SYSCFG_PMCSETR_ETH_SEL_GMII_MII);
- if (eth_clk_sel)
+ /*
+ * If eth_clk_sel is set, use internal ETH_CLKx clock from RCC,
+ * otherwise use external clock from IO pin (requires matching
+ * GPIO block AF setting of that pin).
+ */
+ if (eth_clk_sel || ext_phyclk)
value |= SYSCFG_PMCSETR_ETH_CLK_SEL;
break;
case PHY_INTERFACE_MODE_RMII:
dev_dbg(dev, "PHY_INTERFACE_MODE_RMII\n");
value = FIELD_PREP(SYSCFG_PMCSETR_ETH_SEL_MASK,
SYSCFG_PMCSETR_ETH_SEL_RMII);
- if (eth_ref_clk_sel)
+ /*
+ * If eth_ref_clk_sel is set, use internal clock from RCC,
+ * otherwise use external clock from ETHn_RX_CLK/ETHn_REF_CLK
+ * IO pin (requires matching GPIO block AF setting of that
+ * pin).
+ */
+ if (eth_ref_clk_sel || ext_phyclk)
value |= SYSCFG_PMCSETR_ETH_REF_CLK_SEL;
break;
case PHY_INTERFACE_MODE_RGMII:
@@ -180,7 +199,12 @@
dev_dbg(dev, "PHY_INTERFACE_MODE_RGMII\n");
value = FIELD_PREP(SYSCFG_PMCSETR_ETH_SEL_MASK,
SYSCFG_PMCSETR_ETH_SEL_RGMII);
- if (eth_clk_sel)
+ /*
+ * If eth_clk_sel is set, use internal ETH_CLKx clock from RCC,
+ * otherwise use external clock from ETHx_CLK125 pin (requires
+ * matching GPIO block AF setting of that pin).
+ */
+ if (eth_clk_sel || ext_phyclk)
value |= SYSCFG_PMCSETR_ETH_CLK_SEL;
break;
default: