mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES based on DT compatible
Currently, the denali NAND driver in U-Boot configures the
SPARE_AREA_SKIP_BYTES based on the CONFIG option.
Recently, Linux kernel merged a patch that associates the proper
value for this register with the DT compatible string.
Do likewise in U-Boot too.
The denali_spl.c still uses CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
diff --git a/drivers/mtd/nand/raw/denali.c b/drivers/mtd/nand/raw/denali.c
index 8537c60..be1b362 100644
--- a/drivers/mtd/nand/raw/denali.c
+++ b/drivers/mtd/nand/raw/denali.c
@@ -1069,11 +1069,18 @@
denali->revision = swab16(ioread32(denali->reg + REVISION));
/*
- * tell driver how many bit controller will skip before writing
- * ECC code in OOB. This is normally used for bad block marker
+ * Set how many bytes should be skipped before writing data in OOB.
+ * If a platform requests a non-zero value, set it to the register.
+ * Otherwise, read the value out, expecting it has already been set up
+ * by firmware.
*/
- denali->oob_skip_bytes = CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES;
- iowrite32(denali->oob_skip_bytes, denali->reg + SPARE_AREA_SKIP_BYTES);
+ if (denali->oob_skip_bytes)
+ iowrite32(denali->oob_skip_bytes,
+ denali->reg + SPARE_AREA_SKIP_BYTES);
+ else
+ denali->oob_skip_bytes = ioread32(denali->reg +
+ SPARE_AREA_SKIP_BYTES);
+
denali_detect_max_banks(denali);
iowrite32(0x0F, denali->reg + RB_PIN_ENABLED);
iowrite32(CHIP_EN_DONT_CARE__FLAG, denali->reg + CHIP_ENABLE_DONT_CARE);
diff --git a/drivers/mtd/nand/raw/denali_dt.c b/drivers/mtd/nand/raw/denali_dt.c
index 1afc61f..587e480 100644
--- a/drivers/mtd/nand/raw/denali_dt.c
+++ b/drivers/mtd/nand/raw/denali_dt.c
@@ -16,6 +16,7 @@
struct denali_dt_data {
unsigned int revision;
unsigned int caps;
+ unsigned int oob_skip_bytes;
const struct nand_ecc_caps *ecc_caps;
};
@@ -23,6 +24,7 @@
512, 8, 15);
static const struct denali_dt_data denali_socfpga_data = {
.caps = DENALI_CAP_HW_ECC_FIXUP,
+ .oob_skip_bytes = 2,
.ecc_caps = &denali_socfpga_ecc_caps,
};
@@ -31,6 +33,7 @@
static const struct denali_dt_data denali_uniphier_v5a_data = {
.caps = DENALI_CAP_HW_ECC_FIXUP |
DENALI_CAP_DMA_64BIT,
+ .oob_skip_bytes = 8,
.ecc_caps = &denali_uniphier_v5a_ecc_caps,
};
@@ -40,6 +43,7 @@
.revision = 0x0501,
.caps = DENALI_CAP_HW_ECC_FIXUP |
DENALI_CAP_DMA_64BIT,
+ .oob_skip_bytes = 8,
.ecc_caps = &denali_uniphier_v5b_ecc_caps,
};
@@ -69,11 +73,13 @@
int ret;
data = (void *)dev_get_driver_data(dev);
- if (data) {
- denali->revision = data->revision;
- denali->caps = data->caps;
- denali->ecc_caps = data->ecc_caps;
- }
+ if (WARN_ON(!data))
+ return -EINVAL;
+
+ denali->revision = data->revision;
+ denali->caps = data->caps;
+ denali->oob_skip_bytes = data->oob_skip_bytes;
+ denali->ecc_caps = data->ecc_caps;
denali->dev = dev;