diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index dee2982..9d647b9 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -247,6 +247,7 @@
 	armada-385-atl-x530.dtb			\
 	armada-385-atl-x530DP.dtb		\
 	armada-385-db-88f6820-amc.dtb		\
+	armada-385-synology-ds116.dtb		\
 	armada-385-thecus-n2350.dtb		\
 	armada-385-turris-omnia.dtb		\
 	armada-388-clearfog.dtb			\
diff --git a/arch/arm/dts/armada-385-synology-ds116.dts b/arch/arm/dts/armada-385-synology-ds116.dts
new file mode 100644
index 0000000..82a0373
--- /dev/null
+++ b/arch/arm/dts/armada-385-synology-ds116.dts
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Synology DS116 NAS
+ *
+ * Copyright (C) 2017 Willy Tarreau <w@1wt.eu>
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Synology DS116";
+	compatible = "marvell,a385-gp", "marvell,armada385", "marvell,armada380";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1 GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+			  MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+		internal-regs {
+			i2c@11000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins>;
+				status = "okay";
+				clock-frequency = <100000>;
+
+				eeprom@57 {
+					compatible = "atmel,24c64";
+					reg = <0x57>;
+				};
+			};
+
+			serial@12000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart0_pins>;
+				status = "okay";
+			};
+
+			serial@12100 {
+				/* A PIC16F1829 is connected to uart1 at 9600 bps,
+				 * and takes single-character orders :
+				 *   "1" : power off // already handled by the poweroff node
+				 *   "2" : short beep
+				 *   "3" : long beep
+				 *   "4" : turn the power LED ON
+				 *   "5" : flash the power LED
+				 *   "6" : turn the power LED OFF
+				 *   "7" : turn the status LED OFF
+				 *   "8" : turn the status LED ON
+				 *   "9" : flash the status LED
+				 *   "A" : flash the motherboard LED (D8)
+				 *   "B" : turn the motherboard LED OFF
+				 *   "C" : hard reset
+				 */
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart1_pins>;
+				status = "okay";
+			};
+
+			poweroff@12100 {
+				compatible = "synology,power-off";
+				reg = <0x12100 0x100>;
+				clocks = <&coreclk 0>;
+			};
+
+			ethernet@70000 {
+				pinctrl-names = "default";
+				phy = <&phy0>;
+				phy-mode = "sgmii";
+				buffer-manager = <&bm>;
+				bm,pool-long = <0>;
+				status = "okay";
+			};
+
+			mdio@72004 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&mdio_pins>;
+
+				phy0: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+
+			sata@a8000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&sata0_pins>;
+				status = "okay";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				sata0: sata-port@0 {
+					reg = <0>;
+					target-supply = <&reg_5v_sata0>;
+				};
+			};
+
+			bm@c8000 {
+				status = "okay";
+			};
+
+			usb3@f0000 {
+				usb-phy = <&usb3_0_phy>;
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				usb-phy = <&usb3_1_phy>;
+				status = "okay";
+			};
+		};
+
+		bm-bppi {
+			status = "okay";
+		};
+
+		gpio-fan {
+			compatible = "gpio-fan";
+			gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>,
+				<&gpio1 17 GPIO_ACTIVE_HIGH>,
+				<&gpio1 16 GPIO_ACTIVE_HIGH>;
+			gpio-fan,speed-map = <   0 0
+					      1500 1
+					      2500 2
+					      3000 3
+					      3400 4
+					      3700 5
+					      3900 6
+					      4000 7>;
+			#cooling-cells = <2>;
+		};
+
+		gpio-leds {
+			compatible = "gpio-leds";
+
+			/* The green part is on gpio0.20 which is also used by
+			 * sata0, and accesses to SATA disk 0 make it blink so it
+			 * doesn't need to be declared here.
+			 */
+			orange {
+				gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+				label = "ds116:orange:disk";
+				default-state = "off";
+			};
+		};
+	};
+
+	usb3_0_phy: usb3_0_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_usb3_0_vbus>;
+		#phy-cells = <0>;
+	};
+
+	usb3_1_phy: usb3_1_phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&reg_usb3_1_vbus>;
+		#phy-cells = <0>;
+	};
+
+	reg_usb3_0_vbus: usb3-vbus0 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3-vbus0";
+		pinctrl-names = "default";
+		pinctrl-0 = <&xhci0_vbus_pins>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_usb3_1_vbus: usb3-vbus1 {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3-vbus1";
+		pinctrl-names = "default";
+		pinctrl-0 = <&xhci1_vbus_pins>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_sata0: pwr-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "pwr_en_sata0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		enable-active-high;
+		regulator-boot-on;
+		gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_5v_sata0: v5-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v5.0-sata0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_sata0>;
+	};
+
+	reg_12v_sata0: v12-sata0 {
+		compatible = "regulator-fixed";
+		regulator-name = "v12.0-sata0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		vin-supply = <&reg_sata0>;
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "macronix,mx25l6405d", "jedec,spi-nor";
+		reg = <0>; /* Chip select 0 */
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+
+		/* Note: there is a redboot partition table despite u-boot
+		 * being used. The names presented here are the same as those
+		 * found in the FIS directory. There is also a small device
+		 * tree in the last 64kB of the RedBoot partition which is not
+		 * enumerated. The MAC address and the serial number are listed
+		 * in the "vendor" partition.
+		 */
+		partition@0 {
+			label = "RedBoot";
+			reg = <0x00000000 0x000f0000>;
+			read-only;
+		};
+
+		partition@c0000 {
+			label = "zImage";
+			reg = <0x000f0000 0x002d0000>;
+		};
+
+		partition@390000 {
+			label = "rd.gz";
+			reg = <0x003c0000 0x00410000>;
+		};
+
+		partition@7d0000 {
+			label = "vendor";
+			reg = <0x007d0000 0x00010000>;
+			read-only;
+		};
+
+		partition@7e0000 {
+			label = "RedBoot config";
+			reg = <0x007e0000 0x00010000>;
+			read-only;
+		};
+
+		partition@7f0000 {
+			label = "FIS directory";
+			reg = <0x007f0000 0x00010000>;
+			read-only;
+		};
+	};
+};
+
+&pinctrl {
+	/* use only one pin for UART1, as mpp20 is used by sata0 */
+	uart1_pins: uart-pins-1 {
+		marvell,pins = "mpp19";
+		marvell,function = "ua1";
+	};
+
+	xhci0_vbus_pins: xhci0_vbus_pins {
+		marvell,pins = "mpp58";
+		marvell,function = "gpio";
+	};
+	xhci1_vbus_pins: xhci1_vbus_pins {
+		marvell,pins = "mpp59";
+		marvell,function = "gpio";
+	};
+};
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index f829e40..16c5e72 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -169,6 +169,10 @@
 	select BOARD_ECC_SUPPORT
 	select MV78460
 
+config TARGET_DS116
+	bool "Support Synology DS116"
+	select 88F6820
+
 config TARGET_DS414
 	bool "Support Synology DS414"
 	select MV78230
@@ -263,6 +267,7 @@
 	default "mvebu_armada-8k" if TARGET_MVEBU_ARMADA_8K
 	default "octeontx2_cn913x" if TARGET_OCTEONTX2_CN913x
 	default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP
+	default "ds116" if TARGET_DS116
 	default "ds414" if TARGET_DS414
 	default "maxbcm" if TARGET_MAXBCM
 	default "n2350" if TARGET_N2350
@@ -283,6 +288,7 @@
 	default "mvebu_armada-8k" if TARGET_MVEBU_ARMADA_8K
 	default "mvebu_armada-8k" if TARGET_OCTEONTX2_CN913x
 	default "db-mv784mp-gp" if TARGET_DB_MV784MP_GP
+	default "ds116" if TARGET_DS116
 	default "ds414" if TARGET_DS414
 	default "maxbcm" if TARGET_MAXBCM
 	default "n2350" if TARGET_N2350
@@ -307,6 +313,7 @@
 	default "Marvell" if TARGET_MVEBU_DB_88F7040
 	default "solidrun" if TARGET_CLEARFOG
 	default "kobol" if TARGET_HELIOS4
+	default "Synology" if TARGET_DS116
 	default "Synology" if TARGET_DS414
 	default "thecus" if TARGET_N2350
 	default "CZ.NIC" if TARGET_TURRIS_OMNIA
diff --git a/board/Synology/ds116/MAINTAINERS b/board/Synology/ds116/MAINTAINERS
new file mode 100644
index 0000000..a5080b0
--- /dev/null
+++ b/board/Synology/ds116/MAINTAINERS
@@ -0,0 +1,7 @@
+DS116 BOARD
+M:	Tony Dinh <mibodhi@gmail.com>
+S:	Maintained
+F:	arch/arm/dts/armada-385-synology-ds116.dts
+F:	board/Synology/ds116/
+F:	include/configs/ds116.h
+F:	configs/ds116_defconfig
diff --git a/board/Synology/ds116/Makefile b/board/Synology/ds116/Makefile
new file mode 100644
index 0000000..952cc1b
--- /dev/null
+++ b/board/Synology/ds116/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2023 Tony Dinh <mibodhi@gmail.com>
+#
+
+obj-y	:= ds116.o
diff --git a/board/Synology/ds116/ds116.c b/board/Synology/ds116/ds116.c
new file mode 100644
index 0000000..cf2575b
--- /dev/null
+++ b/board/Synology/ds116/ds116.c
@@ -0,0 +1,135 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2023 Tony Dinh <mibodhi@gmail.com>
+ *
+ */
+
+#include <i2c.h>
+#include <init.h>
+#include <miiphy.h>
+#include <net.h>
+#include <netdev.h>
+#include <asm/global_data.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <linux/bitops.h>
+
+#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
+#include <../serdes/a38x/high_speed_env_spec.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Those DS116_GPP_xx values and defines in board_serdes_map, and board_topology_map
+ * are taken from Marvell U-Boot version
+ * U-Boot 2013.01-g6cc0a6d (Marvell version: 2015_T1.0p16)
+ */
+#define DS116_GPP_OUT_ENA_LOW						\
+	(~(BIT(1)  | BIT(4)  | BIT(6)  | BIT(7)  | BIT(8)  | BIT(9)  |	\
+	   BIT(10) | BIT(11) | BIT(15) | BIT(19) | BIT(22) | BIT(23) |	\
+	   BIT(25) | BIT(26) | BIT(27) | BIT(29) | BIT(30) | BIT(31)))
+#define DS116_GPP_OUT_ENA_MID						\
+	(~(BIT(0) | BIT(1) | BIT(2) | BIT(3) | BIT(4) | BIT(15) |	\
+	   BIT(16) | BIT(17) | BIT(18) | BIT(26) | BIT(27)))
+
+#define DS116_GPP_OUT_VAL_LOW	BIT(15)
+#define DS116_GPP_OUT_VAL_MID	(BIT(26) | BIT(27))
+#define DS116_GPP_POL_LOW	0x0
+#define DS116_GPP_POL_MID	0x0
+
+static struct serdes_map board_serdes_map[] = {
+	{SGMII0, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{SATA0, SERDES_SPEED_6_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+};
+
+int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
+{
+	*serdes_map_array = board_serdes_map;
+	*count = ARRAY_SIZE(board_serdes_map);
+	return 0;
+}
+
+/*
+ * Define the DDR layout / topology here in the board file. This will
+ * be used by the DDR3 init code in the SPL U-Boot version to configure
+ * the DDR3 controller.
+ */
+static struct mv_ddr_topology_map board_topology_map = {
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
+	{ { { {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0} },
+	    SPEED_BIN_DDR_1866L,        /* speed_bin */
+	    MV_DDR_DEV_WIDTH_16BIT,     /* memory_width - 16 bits */
+	    MV_DDR_DIE_CAP_4GBIT,       /* mem_size - DS116 board has 2x512MB DRAM banks */
+	    MV_DDR_FREQ_800,            /* frequency */
+	    0, 0,			/* cas_wl cas_l */
+	    MV_DDR_TEMP_LOW,		/* temperature */
+	    MV_DDR_TIM_DEFAULT} },	/* timing */
+	BUS_MASK_32BIT,			/* Busses mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined */
+	{ {0} },			/* raw spd data */
+	{0}				/* timing parameters */
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+int board_early_init_f(void)
+{
+	/*
+	 * Those MPP values are taken from the Marvell U-Boot version
+	 * U-Boot 2013.01-g6cc0a6d (Marvell version: 2015_T1.0p16)
+	 */
+
+	/* Configure MPP */
+	writel(0x00111111, MVEBU_MPP_BASE + 0x00);
+	writel(0x00000000, MVEBU_MPP_BASE + 0x04);
+	writel(0x11040330, MVEBU_MPP_BASE + 0x08);
+	writel(0x00000011, MVEBU_MPP_BASE + 0x0c);
+	writel(0x00000000, MVEBU_MPP_BASE + 0x10);
+	writel(0x00000000, MVEBU_MPP_BASE + 0x14);
+	writel(0x00000000, MVEBU_MPP_BASE + 0x18);
+	writel(0x00000000, MVEBU_MPP_BASE + 0x1c);
+
+	/* Set GPP Out value */
+	writel(DS116_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
+	writel(DS116_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
+
+	/* Set GPP Polarity */
+	writel(DS116_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
+	writel(DS116_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
+
+	/* Set GPP Out Enable */
+	writel(DS116_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
+	writel(DS116_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+int board_eth_init(struct bd_info *bis)
+{
+	cpu_eth_init(bis); /* Built in controller(s) come first */
+	return pci_eth_init(bis);
+}
diff --git a/configs/ds116_defconfig b/configs/ds116_defconfig
new file mode 100644
index 0000000..5546017
--- /dev/null
+++ b/configs/ds116_defconfig
@@ -0,0 +1,92 @@
+CONFIG_ARM=y
+CONFIG_ARCH_CPU_INIT=y
+CONFIG_SYS_THUMB_BUILD=y
+CONFIG_ARCH_MVEBU=y
+CONFIG_SUPPORT_PASSING_ATAGS=y
+CONFIG_CMDLINE_TAG=y
+CONFIG_INITRD_TAG=y
+CONFIG_TEXT_BASE=0x00800000
+CONFIG_SPL_LIBCOMMON_SUPPORT=y
+CONFIG_SPL_LIBGENERIC_SUPPORT=y
+CONFIG_NR_DRAM_BANKS=2
+CONFIG_TARGET_DS116=y
+CONFIG_ENV_SIZE=0x10000
+CONFIG_ENV_OFFSET=0x7E0000
+CONFIG_ENV_SECT_SIZE=0x10000
+CONFIG_DEFAULT_DEVICE_TREE="armada-385-synology-ds116"
+CONFIG_SPL_TEXT_BASE=0x40000030
+CONFIG_SYS_PROMPT="DS116> "
+CONFIG_SPL_SERIAL=y
+CONFIG_SPL=y
+CONFIG_DEBUG_UART_BASE=0xf1012000
+CONFIG_DEBUG_UART_CLOCK=250000000
+CONFIG_IDENT_STRING="\nSynology DS116"
+CONFIG_SYS_LOAD_ADDR=0x800000
+CONFIG_DEBUG_UART=y
+CONFIG_AHCI=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0xff0000
+CONFIG_BOOTDELAY=10
+CONFIG_USE_PREBOOT=y
+CONFIG_SYS_CONSOLE_INFO_QUIET=y
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_DISPLAY_BOARDINFO_LATE=y
+CONFIG_SPL_MAX_SIZE=0x22fd0
+CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
+CONFIG_SPL_BSS_START_ADDR=0x40023000
+CONFIG_SPL_BSS_MAX_SIZE=0x4000
+CONFIG_SPL_SYS_MALLOC_SIMPLE=y
+# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
+CONFIG_SPL_STACK=0x4002c000
+CONFIG_SPL_I2C=y
+CONFIG_SYS_MAXARGS=32
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPIO_READ=y
+CONFIG_CMD_I2C=y
+CONFIG_CMD_PCI=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_USB=y
+CONFIG_CMD_TFTPPUT=y
+CONFIG_CMD_SNTP=y
+CONFIG_CMD_DNS=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIME=y
+CONFIG_CMD_MTDPARTS=y
+CONFIG_MTDPARTS_DEFAULT="mtdparts=spi0.0:1m(u-boot),7040k(kernel),64k(u-boot-env),-(data)"
+CONFIG_ENV_OVERWRITE=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_VERSION_VARIABLE=y
+CONFIG_ARP_TIMEOUT=200
+CONFIG_NET_RETRY_COUNT=50
+CONFIG_NET_RANDOM_ETHADDR=y
+CONFIG_NETCONSOLE=y
+CONFIG_SPL_OF_TRANSLATE=y
+CONFIG_AHCI_MVEBU=y
+CONFIG_LBA48=y
+CONFIG_SYS_64BIT_LBA=y
+CONFIG_DM_I2C=y
+CONFIG_SYS_I2C_MVTWSI=y
+CONFIG_MTD=y
+CONFIG_SF_DEFAULT_SPEED=50000000
+CONFIG_SPI_FLASH_MACRONIX=y
+CONFIG_SPI_FLASH_STMICRO=y
+CONFIG_PHY_MARVELL=y
+CONFIG_PHY_GIGE=y
+CONFIG_MVNETA=y
+CONFIG_MII=y
+CONFIG_MVMDIO=y
+CONFIG_PCI=y
+CONFIG_PCI_MVEBU=y
+CONFIG_PINCTRL=y
+CONFIG_PINCTRL_ARMADA_38X=y
+CONFIG_DM_RTC=y
+CONFIG_RTC_ARMADA38X=y
+CONFIG_SCSI=y
+CONFIG_SPL_DEBUG_UART_BASE=0xd0012000
+CONFIG_DEBUG_UART_SHIFT=2
+CONFIG_SYS_NS16550=y
+CONFIG_KIRKWOOD_SPI=y
+CONFIG_USB=y
+CONFIG_USB_XHCI_HCD=y
+CONFIG_USB_EHCI_HCD=y
diff --git a/include/configs/ds116.h b/include/configs/ds116.h
new file mode 100644
index 0000000..031f4f6
--- /dev/null
+++ b/include/configs/ds116.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright (C) 2023 Tony Dinh <mibodhi@gmail.com>
+ *
+ */
+
+#ifndef _CONFIG_DS116_H
+#define _CONFIG_DS116_H
+
+#define PHY_ANEG_TIMEOUT	8000	/* PHY needs a longer aneg time */
+
+/* Keep device tree and initrd in lower memory so the kernel can access them */
+#define RELOCATION_LIMITS_ENV_SETTINGS  \
+	"fdt_high=0x10000000\0"         \
+	"initrd_high=0x10000000\0"
+
+/*
+ * mv-common.h should be defined after CMD configs since it used them
+ * to enable certain macros
+ */
+#include "mv-common.h"
+
+/* Include the common distro boot environment */
+#ifndef CONFIG_SPL_BUILD
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(USB, usb, 0) \
+	func(SCSI, scsi, 0) \
+	func(PXE, pxe, na) \
+	func(DHCP, dhcp, na)
+
+#define KERNEL_ADDR_R	__stringify(0x1000000)
+#define FDT_ADDR_R	__stringify(0x2000000)
+#define RAMDISK_ADDR_R	__stringify(0x2200000)
+#define SCRIPT_ADDR_R	__stringify(0x1800000)
+#define PXEFILE_ADDR_R	__stringify(0x1900000)
+
+#define LOAD_ADDRESS_ENV_SETTINGS \
+	"kernel_addr_r=" KERNEL_ADDR_R "\0" \
+	"fdt_addr_r=" FDT_ADDR_R "\0" \
+	"ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \
+	"scriptaddr=" SCRIPT_ADDR_R "\0" \
+	"pxefile_addr_r=" PXEFILE_ADDR_R "\0"
+
+#include <config_distro_bootcmd.h>
+
+#define CFG_EXTRA_ENV_SETTINGS \
+	RELOCATION_LIMITS_ENV_SETTINGS \
+	LOAD_ADDRESS_ENV_SETTINGS \
+	"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
+	"console=ttyS0,115200\0" \
+	BOOTENV
+
+#endif /* CONFIG_SPL_BUILD */
+
+#endif /* _CONFIG_DS116_H */