arm: mvebu: Add support for Synology DS116 (Armada 385)
Synology DS116 is a NAS based on Marvell Armada 385 SoC.
Board Specification:
- Marvel MV88F6820 Dual Core at 1.8GHz
- 1 GiB DDR3 RAM
- 8MB Macronix mx25l6405d SPI flash
- I2C
- 2x USB 3.0
- 1x GBE LAN port (PHY: Marvell 88E1510)
- 1x SATA (6 Gbps)
- 3x LED
- PIC16F1829 (connected to uart1)
- GPIO fan
- serial console
Note that this patch depends on the add-support for Thecus N2350 patch:
https://patchwork.ozlabs.org/project/uboot/patch/20230201231306.7010-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index dee2982..9d647b9 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -247,6 +247,7 @@
armada-385-atl-x530.dtb \
armada-385-atl-x530DP.dtb \
armada-385-db-88f6820-amc.dtb \
+ armada-385-synology-ds116.dtb \
armada-385-thecus-n2350.dtb \
armada-385-turris-omnia.dtb \
armada-388-clearfog.dtb \
diff --git a/arch/arm/dts/armada-385-synology-ds116.dts b/arch/arm/dts/armada-385-synology-ds116.dts
new file mode 100644
index 0000000..82a0373
--- /dev/null
+++ b/arch/arm/dts/armada-385-synology-ds116.dts
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Device Tree file for Synology DS116 NAS
+ *
+ * Copyright (C) 2017 Willy Tarreau <w@1wt.eu>
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Synology DS116";
+ compatible = "marvell,a385-gp", "marvell,armada385", "marvell,armada380";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x40000000>; /* 1 GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+ MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000
+ MBUS_ID(0x0c, 0x04) 0 0xf1200000 0x100000>;
+
+ internal-regs {
+ i2c@11000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "okay";
+ clock-frequency = <100000>;
+
+ eeprom@57 {
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ };
+ };
+
+ serial@12000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "okay";
+ };
+
+ serial@12100 {
+ /* A PIC16F1829 is connected to uart1 at 9600 bps,
+ * and takes single-character orders :
+ * "1" : power off // already handled by the poweroff node
+ * "2" : short beep
+ * "3" : long beep
+ * "4" : turn the power LED ON
+ * "5" : flash the power LED
+ * "6" : turn the power LED OFF
+ * "7" : turn the status LED OFF
+ * "8" : turn the status LED ON
+ * "9" : flash the status LED
+ * "A" : flash the motherboard LED (D8)
+ * "B" : turn the motherboard LED OFF
+ * "C" : hard reset
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+ status = "okay";
+ };
+
+ poweroff@12100 {
+ compatible = "synology,power-off";
+ reg = <0x12100 0x100>;
+ clocks = <&coreclk 0>;
+ };
+
+ ethernet@70000 {
+ pinctrl-names = "default";
+ phy = <&phy0>;
+ phy-mode = "sgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <0>;
+ status = "okay";
+ };
+
+ mdio@72004 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+
+ phy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+
+ sata@a8000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sata0_pins>;
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sata0: sata-port@0 {
+ reg = <0>;
+ target-supply = <®_5v_sata0>;
+ };
+ };
+
+ bm@c8000 {
+ status = "okay";
+ };
+
+ usb3@f0000 {
+ usb-phy = <&usb3_0_phy>;
+ status = "okay";
+ };
+
+ usb3@f8000 {
+ usb-phy = <&usb3_1_phy>;
+ status = "okay";
+ };
+ };
+
+ bm-bppi {
+ status = "okay";
+ };
+
+ gpio-fan {
+ compatible = "gpio-fan";
+ gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>,
+ <&gpio1 17 GPIO_ACTIVE_HIGH>,
+ <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = < 0 0
+ 1500 1
+ 2500 2
+ 3000 3
+ 3400 4
+ 3700 5
+ 3900 6
+ 4000 7>;
+ #cooling-cells = <2>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ /* The green part is on gpio0.20 which is also used by
+ * sata0, and accesses to SATA disk 0 make it blink so it
+ * doesn't need to be declared here.
+ */
+ orange {
+ gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>;
+ label = "ds116:orange:disk";
+ default-state = "off";
+ };
+ };
+ };
+
+ usb3_0_phy: usb3_0_phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_usb3_0_vbus>;
+ #phy-cells = <0>;
+ };
+
+ usb3_1_phy: usb3_1_phy {
+ compatible = "usb-nop-xceiv";
+ vcc-supply = <®_usb3_1_vbus>;
+ #phy-cells = <0>;
+ };
+
+ reg_usb3_0_vbus: usb3-vbus0 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb3-vbus0";
+ pinctrl-names = "default";
+ pinctrl-0 = <&xhci0_vbus_pins>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_usb3_1_vbus: usb3-vbus1 {
+ compatible = "regulator-fixed";
+ regulator-name = "usb3-vbus1";
+ pinctrl-names = "default";
+ pinctrl-0 = <&xhci1_vbus_pins>;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ gpio = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_sata0: pwr-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "pwr_en_sata0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ enable-active-high;
+ regulator-boot-on;
+ gpio = <&gpio0 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ reg_5v_sata0: v5-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "v5.0-sata0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_sata0>;
+ };
+
+ reg_12v_sata0: v12-sata0 {
+ compatible = "regulator-fixed";
+ regulator-name = "v12.0-sata0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ vin-supply = <®_sata0>;
+ };
+};
+
+&spi0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "macronix,mx25l6405d", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <50000000>;
+ m25p,fast-read;
+
+ /* Note: there is a redboot partition table despite u-boot
+ * being used. The names presented here are the same as those
+ * found in the FIS directory. There is also a small device
+ * tree in the last 64kB of the RedBoot partition which is not
+ * enumerated. The MAC address and the serial number are listed
+ * in the "vendor" partition.
+ */
+ partition@0 {
+ label = "RedBoot";
+ reg = <0x00000000 0x000f0000>;
+ read-only;
+ };
+
+ partition@c0000 {
+ label = "zImage";
+ reg = <0x000f0000 0x002d0000>;
+ };
+
+ partition@390000 {
+ label = "rd.gz";
+ reg = <0x003c0000 0x00410000>;
+ };
+
+ partition@7d0000 {
+ label = "vendor";
+ reg = <0x007d0000 0x00010000>;
+ read-only;
+ };
+
+ partition@7e0000 {
+ label = "RedBoot config";
+ reg = <0x007e0000 0x00010000>;
+ read-only;
+ };
+
+ partition@7f0000 {
+ label = "FIS directory";
+ reg = <0x007f0000 0x00010000>;
+ read-only;
+ };
+ };
+};
+
+&pinctrl {
+ /* use only one pin for UART1, as mpp20 is used by sata0 */
+ uart1_pins: uart-pins-1 {
+ marvell,pins = "mpp19";
+ marvell,function = "ua1";
+ };
+
+ xhci0_vbus_pins: xhci0_vbus_pins {
+ marvell,pins = "mpp58";
+ marvell,function = "gpio";
+ };
+ xhci1_vbus_pins: xhci1_vbus_pins {
+ marvell,pins = "mpp59";
+ marvell,function = "gpio";
+ };
+};