diff --git a/board/freescale/t208xqds/README b/board/freescale/t208xqds/README
index d690857..b52d961 100755
--- a/board/freescale/t208xqds/README
+++ b/board/freescale/t208xqds/README
@@ -55,14 +55,14 @@
  - Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
 Ethernet interfaces:
  - Two 1Gbps RGMII on-board ports
- - Four 10Gbps XFI on-board cages
+ - Four 10GBase-R on-board cages
  - 1Gbps/2.5Gbps SGMII Riser card
  - 10Gbps XAUI Riser card
 Accelerator:
  - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
 SerDes:
  - 16 lanes up to 10.3125GHz
- - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
+ - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, 10GBase-R and XAUI
 IFC:
  - 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
 eSPI:
@@ -85,14 +85,14 @@
  - QIXIS-II FPGA system controll
 Debug Features:
  - Support Legacy, COP/JTAG, Aurora, Event and EVT
-XFI:
- - XFI is supported on T2080QDS through Lane A/B/C/D on Serdes 1 routed to
+10GBase-R:
+ - 10GBase-R is supported on T2080QDS through Lane A/B/C/D on Serdes 1 routed to
  a on-board SFP+ cages, which to house optical module (fiber cable) or
  direct attach cable(copper), the copper cable is used to emulate
  10GBASE-KR scenario.
- So, for XFI usage, there are two scenarios, one will use fiber cable,
+ So, for 10GBase-R usage, there are two scenarios, one will use fiber cable,
  another will use copper cable. An hwconfig env "fsl_10gkr_copper" is
- introduced to indicate a XFI port will use copper cable, and U-Boot
+ introduced to indicate a 10GBase-R port will use copper cable, and U-Boot
  will fixup the dtb accordingly.
  It's used as: fsl_10gkr_copper:<10g_mac_name>
  The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4, they
@@ -100,10 +100,10 @@
  "fsl_10gkr_copper", it will use copper cable, otherwise, fiber cable
  will be used by default.
  for ex. set "fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4" in
- hwconfig, then both four XFI ports will use copper cable.
+ hwconfig, then both four 10GBase-R ports will use copper cable.
  set "fsl_10gkr_copper:fm1_10g1,fm1_10g2" in hwconfig, then first two
- XFI ports will use copper cable, the other two XFI ports will use fiber
- cable.
+ 10GBase-R ports will use copper cable, the other two 10GBase-R ports will use
+ fiber cable.
 1000BASE-KX(1G-KX):
  - T2080QDS can support 1G-KX by using SGMII protocol, but serdes lane
  runs in 1G-KX mode. By default, the lane runs in SGMII mode, to set a lane