net: replace the "xfi" phy-mode with "10gbase-r"
As part of the effort of making U-Boot work with the same device tree as
Linux, there is an issue with the "xfi" phy-mode. To be precise, in
Linux there was a discussion (for those who have time to read:
https://lore.kernel.org/netdev/1576768881-24971-2-git-send-email-madalin.bucur@oss.nxp.com/)
which led to a patch:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=c114574ebfdf42f826776f717c8056a00fa94881
TL;DR: "xfi" was standardized in Linux as "10gbase-r".
This patch changes the relevant occurrences in U-Boot to use "10gbase-r"
instead of "xfi" wherever applicable.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
diff --git a/board/freescale/ls1043aqds/README b/board/freescale/ls1043aqds/README
index 913537d..f5aa51d 100644
--- a/board/freescale/ls1043aqds/README
+++ b/board/freescale/ls1043aqds/README
@@ -18,7 +18,7 @@
- SGMII, SGMII 2.5
- QSGMII
- SATA 3.0
- - XFI
+ - 10GBase-R
- DDR Controller
- 2GB 40bits (8-bits ECC) DDR4 SDRAM. Support rates of up to 1600MT/s
-IFC/Local Bus
diff --git a/board/freescale/ls1043aqds/eth.c b/board/freescale/ls1043aqds/eth.c
index c3efe8a..81e18f6 100644
--- a/board/freescale/ls1043aqds/eth.c
+++ b/board/freescale/ls1043aqds/eth.c
@@ -242,13 +242,13 @@
"qsgmii");
} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII &&
port == FM1_10GEC1) {
- /* XFI interface */
+ /* 10GBase-R interface */
f_link.phy_id = cpu_to_fdt32(port);
f_link.duplex = cpu_to_fdt32(1);
f_link.link_speed = cpu_to_fdt32(10000);
f_link.pause = 0;
f_link.asym_pause = 0;
- /* no PHY for XFI */
+ /* no PHY for 10GBase-R */
fdt_delprop(fdt, offset, "phy-handle");
fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link));
fdt_setprop_string(fdt, offset, "phy-connection-type", "xgmii");
diff --git a/board/freescale/ls1043ardb/README b/board/freescale/ls1043ardb/README
index 709ddbb..66ee578 100644
--- a/board/freescale/ls1043ardb/README
+++ b/board/freescale/ls1043ardb/README
@@ -17,7 +17,7 @@
- PCI Express 2.0 with two PCIe connectors supporting: miniPCIe card and
standard PCIe card
- QSGMII with x4 RJ45 connector
- - XFI with x1 RJ45 connector
+ - 10GBase-R with x1 RJ45 connector
- DDR Controller
- 2GB 32bits DDR4 SDRAM. Support rates of up to 1600MT/s
-IFC/Local Bus
diff --git a/board/freescale/ls1043ardb/eth.c b/board/freescale/ls1043ardb/eth.c
index 1f01c15..fa59116 100644
--- a/board/freescale/ls1043ardb/eth.c
+++ b/board/freescale/ls1043ardb/eth.c
@@ -65,7 +65,7 @@
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++)
fm_info_set_mdio(i, dev);
- /* XFI on lane A, MAC 9 */
+ /* 10GBase-R on lane A, MAC 9 */
fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
fm_info_set_mdio(FM1_10GEC1, dev);
diff --git a/board/freescale/ls1046aqds/README b/board/freescale/ls1046aqds/README
index b8fa326..d646901 100644
--- a/board/freescale/ls1046aqds/README
+++ b/board/freescale/ls1046aqds/README
@@ -18,7 +18,7 @@
- SGMII, SGMII 2.5
- QSGMII
- SATA 3.0
- - XFI
+ - 10GBase-R
- DDR Controller
- 8GB 64bits DDR4 SDRAM. Support rates of up to 2133MT/s
-IFC/Local Bus
diff --git a/board/freescale/ls1046aqds/eth.c b/board/freescale/ls1046aqds/eth.c
index 33db552..2352832 100644
--- a/board/freescale/ls1046aqds/eth.c
+++ b/board/freescale/ls1046aqds/eth.c
@@ -217,13 +217,13 @@
/* Backplane KR mode: skip fixups */
printf("Interface %d in backplane KR mode\n", port);
} else {
- /* XFI interface */
+ /* 10GBase-R interface */
f_link.phy_id = cpu_to_fdt32(port);
f_link.duplex = cpu_to_fdt32(1);
f_link.link_speed = cpu_to_fdt32(10000);
f_link.pause = 0;
f_link.asym_pause = 0;
- /* no PHY for XFI */
+ /* no PHY for 10GBase-R */
fdt_delprop(fdt, offset, "phy-handle");
fdt_setprop(fdt, offset, "fixed-link", &f_link,
sizeof(f_link));
diff --git a/board/freescale/ls1046ardb/README b/board/freescale/ls1046ardb/README
index a38c9d4..1660f7c 100644
--- a/board/freescale/ls1046ardb/README
+++ b/board/freescale/ls1046ardb/README
@@ -14,8 +14,8 @@
LS1046ARDB board Overview
-----------------------
- SERDES1 Connections, 4 lanes supporting:
- - Lane0: XFI with x1 RJ45 connector
- - Lane1: XFI Cage
+ - Lane0: 10GBase-R with x1 RJ45 connector
+ - Lane1: 10GBase-R Cage
- Lane2: SGMII.5
- Lane3: SGMII.6
- SERDES2 Connections, 4 lanes supporting:
diff --git a/board/freescale/ls1046ardb/eth.c b/board/freescale/ls1046ardb/eth.c
index 4905302..a3e147a 100644
--- a/board/freescale/ls1046ardb/eth.c
+++ b/board/freescale/ls1046ardb/eth.c
@@ -67,7 +67,7 @@
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++)
fm_info_set_mdio(i, dev);
- /* XFI on lane A, MAC 9 */
+ /* 10GBase-R on lane A, MAC 9 */
dev = miiphy_get_dev_by_name(DEFAULT_FM_TGEC_MDIO_NAME);
fm_info_set_mdio(FM1_10GEC1, dev);
diff --git a/board/freescale/ls1088a/README b/board/freescale/ls1088a/README
index aa0fb6a..5315909 100644
--- a/board/freescale/ls1088a/README
+++ b/board/freescale/ls1088a/README
@@ -42,7 +42,7 @@
- SERDES Connections, 16 lanes supporting:
- PCI Express - 3.0
- SATA 3.0
- - XFI
+ - 10GBase-R
- QSGMII
- DDR Controller
- One ports of 72-bits (8-bits ECC, 64-bits DATA) DDR4. Each port supports four
@@ -106,7 +106,7 @@
- SERDES Connections, 16 lanes supporting:
- PCI Express - 3.0
- SATA 3.0
- - 2 XFI
+ - 2 10GBase-R
- QSGMII, SGMII with help for Riser card
- 2 RGMII
- 5 slot for Riser card or PCIe NIC
diff --git a/board/freescale/ls1088a/eth_ls1088ardb.c b/board/freescale/ls1088a/eth_ls1088ardb.c
index a8e9ef1..1ba5e94 100644
--- a/board/freescale/ls1088a/eth_ls1088ardb.c
+++ b/board/freescale/ls1088a/eth_ls1088ardb.c
@@ -52,9 +52,9 @@
switch (srds_s1) {
case 0x1D:
/*
- * XFI does not need a PHY to work, but to avoid U-boot use
- * default PHY address which is zero to a MAC when it found
- * a MAC has no PHY address, we give a PHY address to XFI
+ * 10GBase-R does not need a PHY to work, but to avoid U-boot
+ * use default PHY address which is zero to a MAC when it found
+ * a MAC has no PHY address, we give a PHY address to 10GBase-R
* MAC error.
*/
wriop_set_phy_address(WRIOP1_DPMAC1, 0, 0x0a);
diff --git a/board/freescale/ls2080aqds/README b/board/freescale/ls2080aqds/README
index 8e31e9e..04c1941 100644
--- a/board/freescale/ls2080aqds/README
+++ b/board/freescale/ls2080aqds/README
@@ -19,7 +19,7 @@
- QSGMII
- SATA 3.0
- XAUI
- - XFI
+ - 10GBase-R
- DDR Controller
- Two ports of 72-bits (8-bits ECC) DDR4. Each port supports four
chip-selects and two DIMM connectors. Support is up to 2133MT/s.
diff --git a/board/freescale/ls2080aqds/eth.c b/board/freescale/ls2080aqds/eth.c
index 914cd0a..7db3789 100644
--- a/board/freescale/ls2080aqds/eth.c
+++ b/board/freescale/ls2080aqds/eth.c
@@ -874,13 +874,12 @@
case 0x4B:
case 0x4C:
/*
- * XFI does not need a PHY to work, but to avoid U-Boot use
- * default PHY address which is zero to a MAC when it found
- * a MAC has no PHY address, we give a PHY address to XFI
- * MAC, and should not use a real XAUI PHY address, since
- * MDIO can access it successfully, and then MDIO thinks
- * the XAUI card is used for the XFI MAC, which will cause
- * error.
+ * 10GBase-R does not need a PHY to work, but to avoid U-Boot
+ * use default PHY address which is zero to a MAC when it found
+ * a MAC has no PHY address, we give a PHY address to 10GBase-R
+ * MAC, and should not use a real XAUI PHY address, since MDIO
+ * can access it successfully, and then MDIO thinks the XAUI
+ * card is used for the 10GBase-R MAC, which will cause error.
*/
wriop_set_phy_address(i, 0, i + 4);
ls2080a_qds_enable_SFP_TX(SFP_TX);
diff --git a/board/freescale/ls2080ardb/README b/board/freescale/ls2080ardb/README
index 205c45c..75a633c 100644
--- a/board/freescale/ls2080ardb/README
+++ b/board/freescale/ls2080ardb/README
@@ -18,7 +18,7 @@
- SERDES Connections, 16 lanes supporting:
- PCI Express - 3.0
- SATA 3.0
- - XFI
+ - 10GBase-R
- DDR Controller
- Two ports of 72-bits (8-bits ECC) DDR4. Each port supports four
chip-selects and two DIMM connectors. Support is up to 2133MT/s.
diff --git a/board/freescale/t102xrdb/README b/board/freescale/t102xrdb/README
index dde3f8c..84deb95 100644
--- a/board/freescale/t102xrdb/README
+++ b/board/freescale/t102xrdb/README
@@ -39,7 +39,7 @@
- One QSGMII interface
- Four SGMII interface supporting 1000 Mbps
- Three SGMII interfaces supporting up to 2500 Mbps
- - 10GbE XFI or 10Base-KR interface
+ - 10GBase-R or 10Base-KR interface
- Additional peripheral interfaces
- Two USB 2.0 controllers with integrated PHY
- SD/eSDHC/eMMC
diff --git a/board/freescale/t102xrdb/eth_t102xrdb.c b/board/freescale/t102xrdb/eth_t102xrdb.c
index 56e6109..b28c545 100644
--- a/board/freescale/t102xrdb/eth_t102xrdb.c
+++ b/board/freescale/t102xrdb/eth_t102xrdb.c
@@ -64,7 +64,7 @@
/* set the on-board RGMII2 PHY */
fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
- /* set 10G XFI with Aquantia AQR105 PHY */
+ /* set 10GBase-R with Aquantia AQR105 PHY */
fm_info_set_phy_address(FM1_10GEC1, FM1_10GEC1_PHY_ADDR);
break;
#endif
diff --git a/board/freescale/t208xqds/README b/board/freescale/t208xqds/README
index d690857..b52d961 100755
--- a/board/freescale/t208xqds/README
+++ b/board/freescale/t208xqds/README
@@ -55,14 +55,14 @@
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- - Four 10Gbps XFI on-board cages
+ - Four 10GBase-R on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
+ - Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, 10GBase-R and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
@@ -85,14 +85,14 @@
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVT
-XFI:
- - XFI is supported on T2080QDS through Lane A/B/C/D on Serdes 1 routed to
+10GBase-R:
+ - 10GBase-R is supported on T2080QDS through Lane A/B/C/D on Serdes 1 routed to
a on-board SFP+ cages, which to house optical module (fiber cable) or
direct attach cable(copper), the copper cable is used to emulate
10GBASE-KR scenario.
- So, for XFI usage, there are two scenarios, one will use fiber cable,
+ So, for 10GBase-R usage, there are two scenarios, one will use fiber cable,
another will use copper cable. An hwconfig env "fsl_10gkr_copper" is
- introduced to indicate a XFI port will use copper cable, and U-Boot
+ introduced to indicate a 10GBase-R port will use copper cable, and U-Boot
will fixup the dtb accordingly.
It's used as: fsl_10gkr_copper:<10g_mac_name>
The <10g_mac_name> can be fm1_10g1, fm1_10g2, fm1_10g3, fm1_10g4, they
@@ -100,10 +100,10 @@
"fsl_10gkr_copper", it will use copper cable, otherwise, fiber cable
will be used by default.
for ex. set "fsl_10gkr_copper:fm1_10g1,fm1_10g2,fm1_10g3,fm1_10g4" in
- hwconfig, then both four XFI ports will use copper cable.
+ hwconfig, then both four 10GBase-R ports will use copper cable.
set "fsl_10gkr_copper:fm1_10g1,fm1_10g2" in hwconfig, then first two
- XFI ports will use copper cable, the other two XFI ports will use fiber
- cable.
+ 10GBase-R ports will use copper cable, the other two 10GBase-R ports will use
+ fiber cable.
1000BASE-KX(1G-KX):
- T2080QDS can support 1G-KX by using SGMII protocol, but serdes lane
runs in 1G-KX mode. By default, the lane runs in SGMII mode, to set a lane
diff --git a/board/freescale/t208xqds/eth_t208xqds.c b/board/freescale/t208xqds/eth_t208xqds.c
index 705387a..2d7fc8b 100644
--- a/board/freescale/t208xqds/eth_t208xqds.c
+++ b/board/freescale/t208xqds/eth_t208xqds.c
@@ -310,16 +310,16 @@
} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
switch (srds_s1) {
- case 0x66: /* XFI interface */
+ case 0x66: /* 10GBase-R interface */
case 0x6b:
case 0x6c:
case 0x6d:
case 0x71:
/*
- * if the 10G is XFI, check hwconfig to see what is the
- * media type, there are two types, fiber or copper,
- * fix the dtb accordingly.
- */
+ * Check hwconfig to see what is the media type, there
+ * are two types, fiber or copper, fix the dtb
+ * accordingly.
+ */
switch (port) {
case FM1_10GEC1:
if (hwconfig_sub("fsl_10gkr_copper", "fm1_10g1")) {
@@ -378,7 +378,7 @@
printf("Interface %d in backplane KR mode\n",
port);
} else {
- /* fixed-link for XFI fiber cable */
+ /* fixed-link for 10GBase-R fiber cable */
f_link.phy_id = port;
f_link.duplex = 1;
f_link.link_speed = 10000;
@@ -538,12 +538,12 @@
case 0x66:
case 0x67:
/*
- * XFI does not need a PHY to work, but to avoid U-Boot use
- * default PHY address which is zero to a MAC when it found
- * a MAC has no PHY address, we give a PHY address to XFI
+ * 10GBase-R does not need a PHY to work, but to avoid U-Boot
+ * use default PHY address which is zero to a MAC when it found
+ * a MAC has no PHY address, we give a PHY address to 10GBase-R
* MAC, and should not use a real XAUI PHY address, since
* MDIO can access it successfully, and then MDIO thinks
- * the XAUI card is used for the XFI MAC, which will cause
+ * the XAUI card is used for the 10GBase-R MAC, which will cause
* error.
*/
fm_info_set_phy_address(FM1_10GEC1, 4);
@@ -701,7 +701,7 @@
(srds_s1 == 0x6a) || (srds_s1 == 0x70) ||
(srds_s1 == 0x6c) || (srds_s1 == 0x6d) ||
(srds_s1 == 0x71)) {
- /* As XFI is in cage intead of a slot, so
+ /* As 10GBase-R is in cage intead of a slot, so
* ensure doesn't disable the corresponding port
*/
break;
diff --git a/board/freescale/t208xqds/t208xqds.c b/board/freescale/t208xqds/t208xqds.c
index 715de10..e54672a 100644
--- a/board/freescale/t208xqds/t208xqds.c
+++ b/board/freescale/t208xqds/t208xqds.c
@@ -136,14 +136,14 @@
break;
case 0x66:
case 0x67:
- /* SD1(A:D) => XFI cage
+ /* SD1(A:D) => 10GBase-R cage
* SD1(E:H) => SLOT1 PCIe4
*/
QIXIS_WRITE(brdcfg[12], 0xfe);
break;
case 0x6a:
case 0x6b:
- /* SD1(A:D) => XFI cage
+ /* SD1(A:D) => 10GBase-R cage
* SD1(E) => SLOT1 PCIe4
* SD1(F:H) => SLOT2 SGMII
*/
@@ -151,14 +151,14 @@
break;
case 0x6c:
case 0x6d:
- /* SD1(A:B) => XFI cage
+ /* SD1(A:B) => 10GBase-R cage
* SD1(C:D) => SLOT3 SGMII
* SD1(E:H) => SLOT1 PCIe4
*/
QIXIS_WRITE(brdcfg[12], 0xda);
break;
case 0x6e:
- /* SD1(A:B) => SFP Module, XFI
+ /* SD1(A:B) => SFP Module, 10GBase-R
* SD1(C:D) => SLOT3 SGMII
* SD1(E:F) => SLOT1 PCIe4 x2
* SD1(G:H) => SLOT2 SGMII
diff --git a/board/freescale/t208xrdb/README b/board/freescale/t208xrdb/README
index ec47c96..c4bfd3b 100644
--- a/board/freescale/t208xrdb/README
+++ b/board/freescale/t208xrdb/README
@@ -54,7 +54,7 @@
T2080PCIe-RDB board Overview
----------------------------
- SERDES Configuration
- - SerDes-1 Lane A-B: to two 10G XFI fiber (MAC9 & MAC10)
+ - SerDes-1 Lane A-B: to two 10GBase-R fiber (MAC9 & MAC10)
- SerDes-1 Lane C-D: to two 10G Base-T (MAC1 & MAC2)
- SerDes-1 Lane E-H: to PCIe Goldfinger (PCIe4 x4, Gen3)
- SerDes-2 Lane A-D: to PCIe Slot (PCIe1 x4, Gen2)
@@ -62,7 +62,7 @@
- SerDes-2 Lane G-H: to SATA1 & SATA2
- Ethernet
- Two on-board 10M/100M/1G RGMII ethernet ports
- - Two on-board 10Gbps XFI fiber ports
+ - Two on-board 10GBase-R fiber ports
- Two on-board 10Gbps Base-T copper ports
- DDR Memory
- Supports 72bit 4GB DDR3-LP SODIMM
diff --git a/board/freescale/t4rdb/eth.c b/board/freescale/t4rdb/eth.c
index c815a3a..34ffaa6 100644
--- a/board/freescale/t4rdb/eth.c
+++ b/board/freescale/t4rdb/eth.c
@@ -106,7 +106,7 @@
#if (CONFIG_SYS_NUM_FMAN == 2)
if ((srds_prtcl_s2 == 56) || (srds_prtcl_s2 == 55)) {
- /* SGMII && XFI */
+ /* SGMII && 10GBase-R */
fm_info_set_phy_address(FM2_DTSEC1, SGMII_PHY_ADDR5);
fm_info_set_phy_address(FM2_DTSEC2, SGMII_PHY_ADDR6);
fm_info_set_phy_address(FM2_DTSEC3, SGMII_PHY_ADDR7);