ARM: dts: at91: Add dts files for at91sam9x5ek
The device tree source files of at91sam9x5ek board are copied from
the Linux v4.10, do the changes below.
- Add the reg property for the pinctrl node.
- Move the gpio (pioA, pioB, pioC ...) nodes as the pinctrl's
slibling nodes, instead of the child nodes.
- Add the "u-boot,dm-pre-reloc" property to determine which nodes
are used by the board_init_f stage.
- Change the compatible of the spi flash to "spi-flash".
- Add the spi0 aliases.
- Fix the compilation warnings.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
diff --git a/arch/arm/dts/at91sam9x5ek.dtsi b/arch/arm/dts/at91sam9x5ek.dtsi
new file mode 100644
index 0000000..f2a532d
--- /dev/null
+++ b/arch/arm/dts/at91sam9x5ek.dtsi
@@ -0,0 +1,167 @@
+/*
+ * at91sam9x5ek.dtsi - Device Tree file for AT91SAM9x5CM Base board
+ *
+ * Copyright (C) 2012 Atmel,
+ * 2012 Nicolas Ferre <nicolas.ferre@atmel.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+#include "at91sam9x5cm.dtsi"
+
+/ {
+ model = "Atmel AT91SAM9X5-EK";
+ compatible = "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs";
+ stdout-path = "serial0:115200n8";
+ u-boot,dm-pre-reloc;
+ };
+
+ ahb {
+ apb {
+ mmc0: mmc@f0008000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_slot0_clk_cmd_dat0
+ &pinctrl_mmc0_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ mmc1: mmc@f000c000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc1
+ &pinctrl_mmc1_slot0_clk_cmd_dat0
+ &pinctrl_mmc1_slot0_dat1_3>;
+ status = "okay";
+ slot@0 {
+ reg = <0>;
+ bus-width = <4>;
+ cd-gpios = <&pioD 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ dbgu: serial@fffff200 {
+ u-boot,dm-pre-reloc;
+ status = "okay";
+ };
+
+ usart0: serial@f801c000 {
+ status = "okay";
+ };
+
+ usb2: gadget@f803c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_board_usb2>;
+ atmel,vbus-gpio = <&pioB 16 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ i2c0: i2c@f8010000 {
+ status = "okay";
+
+ wm8731: wm8731@1a {
+ compatible = "wm8731";
+ reg = <0x1a>;
+ };
+ };
+
+ adc0: adc@f804c000 {
+ atmel,adc-ts-wires = <4>;
+ atmel,adc-ts-pressure-threshold = <10000>;
+ status = "okay";
+ };
+
+ pinctrl@fffff400 {
+ camera_sensor {
+ pinctrl_pck0_as_isi_mck: pck0_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOC 15 AT91_PERIPH_C AT91_PINCTRL_NONE>; /* ISI_MCK */
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOA 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOA 7 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
+
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOD 15 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD15 gpio CD pin pull up and deglitch */
+ };
+ };
+
+ mmc1 {
+ pinctrl_board_mmc1: mmc1-board {
+ atmel,pins =
+ <AT91_PIOD 14 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>; /* PD14 gpio CD pin pull up and deglitch */
+ };
+ };
+
+ usb2 {
+ pinctrl_board_usb2: usb2-board {
+ atmel,pins =
+ <AT91_PIOB 16 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>; /* PB16 gpio vbus sense, deglitch */
+ };
+ };
+ };
+
+ spi0: spi@f0000000 {
+ status = "okay";
+ cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
+ spi_flash@0 {
+ compatible = "spi-flash";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+ };
+
+ watchdog@fffffe40 {
+ status = "okay";
+ };
+
+ ssc0: ssc@f0010000 {
+ status = "okay";
+ };
+ };
+
+ usb0: ohci@00600000 {
+ status = "okay";
+ num-ports = <3>;
+ atmel,vbus-gpio = <0 /* &pioD 18 GPIO_ACTIVE_LOW *//* Activate to have access to port A */
+ &pioD 19 GPIO_ACTIVE_LOW
+ &pioD 20 GPIO_ACTIVE_LOW
+ >;
+ };
+
+ usb1: ehci@00700000 {
+ status = "okay";
+ };
+ };
+
+ sound {
+ compatible = "atmel,sam9x5-wm8731-audio";
+
+ atmel,model = "wm8731 @ AT91SAM9X5EK";
+
+ atmel,audio-routing =
+ "Headphone Jack", "RHPOUT",
+ "Headphone Jack", "LHPOUT",
+ "LLINEIN", "Line In Jack",
+ "RLINEIN", "Line In Jack";
+
+ atmel,ssc-controller = <&ssc0>;
+ atmel,audio-codec = <&wm8731>;
+ };
+};