include/configs/kmeter1.h - filogic/uboot - Gitiles

 /*
  * Copyright (C) 2006 Freescale Semiconductor, Inc.
  *                    Dave Liu <daveliu@freescale.com>
  *
  * Copyright (C) 2007 Logic Product Development, Inc.
  *                    Peter Barada <peterb@logicpd.com>
  *
  * Copyright (C) 2007 MontaVista Software, Inc.
  *                    Anton Vorontsov <avorontsov@ru.mvista.com>
  *
  * (C) Copyright 2008
  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
  * published by the Free Software Foundation; either version 2 of
  * the License, or (at your option) any later version.
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1 /* E300 family */
 #define CONFIG_QE		1 /* Has QE */
 #define CONFIG_MPC83XX		1 /* MPC83XX family */
 #define CONFIG_MPC8360		1 /* MPC8360 CPU specific */
 #define CONFIG_KMETER1		1 /* KMETER1 board specific */

 /* include common defines/options for all Keymile boards */
 #include "keymile-common.h"

 /*
  * System Clock Setup
  */
 #define CONFIG_83XX_CLKIN		66000000
 #define CONFIG_SYS_CLK_FREQ		66000000
 #define CONFIG_83XX_PCICLK		66000000

 /*
  * Hardware Reset Configuration Word
  */
 #define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_CSB_TO_CLKIN_4X1 | \
 	HRCWL_CORE_TO_CSB_2X1 | \
 	HRCWL_CE_PLL_VCO_DIV_2 | \
 	HRCWL_CE_TO_PLL_1X6 )

 #define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_CORE_ENABLE | \
 	HRCWH_FROM_0X00000100 | \
 	HRCWH_BOOTSEQ_NORMAL | \
 	HRCWH_SW_WATCHDOG_DISABLE | \
 	HRCWH_ROM_LOC_LOCAL_16BIT | \
 	HRCWH_BIG_ENDIAN | \
 	HRCWH_LDP_CLEAR )

 /*
  * System IO Config
  */
 #define CONFIG_SYS_SICRH		0x00000006
 #define CONFIG_SYS_SICRL		0x00000000

 /*
  * IMMR new address
  */
 #define CONFIG_SYS_IMMR		0xE0000000

 /*
  * DDR Setup
  */
 #define CONFIG_SYS_DDR_BASE		0x00000000 /* DDR is system memory */
 #define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
 					DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

 #define CFG_83XX_DDR_USES_CS0

 #undef CONFIG_DDR_ECC

 /*
  * DDRCDR - DDR Control Driver Register
  */

 #undef CONFIG_SPD_EEPROM	/* Do not use SPD EEPROM for DDR setup */

 /*
  * Manually set up DDR parameters
  */
 #define CONFIG_DDR_II
 #define CONFIG_SYS_DDR_SIZE		256 /* MB */
 #define CONFIG_SYS_DDR_CS0_BNDS		0x0000000f
 #define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
 					 CSCONFIG_ROW_BIT_13 | \
 					 CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS)

 #define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
 					 SDRAM_CFG_SREN)
 #define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
 #define CONFIG_SYS_DDR_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
 #define CONFIG_SYS_DDR_INTERVAL	((0x100 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
 				 (0x406 << SDRAM_INTERVAL_REFINT_SHIFT))

 #define CONFIG_SYS_DDR_MODE		0x04440242
 #define CONFIG_SYS_DDR_MODE2		0x00800000

 #define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
 				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
 				 (6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
 				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
 				 (0 << TIMING_CFG0_WWT_SHIFT) | \
 				 (0 << TIMING_CFG0_RRT_SHIFT) | \
 				 (0 << TIMING_CFG0_WRT_SHIFT) | \
 				 (0 << TIMING_CFG0_RWT_SHIFT))

 #define CONFIG_SYS_DDR_TIMING_1	((      TIMING_CFG1_CASLAT_40) | \
 				 ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \
 				 ( 1 << TIMING_CFG1_ACTTOACT_SHIFT) | \
 				 ( 2 << TIMING_CFG1_WRREC_SHIFT) | \
 				 ( 2 << TIMING_CFG1_REFREC_SHIFT) | \
 				 ( 2 << TIMING_CFG1_ACTTORW_SHIFT) | \
 				 ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
 				 ( 2 << TIMING_CFG1_PRETOACT_SHIFT))

 #define CONFIG_SYS_DDR_TIMING_2	((5 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
 				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
 				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
 				 (1 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
 				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
 				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
 				 (4 << TIMING_CFG2_CPO_SHIFT))

 #define CONFIG_SYS_DDR_TIMING_3	0x00000000

 /*
  * The reserved memory
  */
 #define CONFIG_SYS_MONITOR_BASE	TEXT_BASE /* start of monitor */
 #define CONFIG_SYS_FLASH_BASE		0xF0000000
 #define CONFIG_SYS_FLASH_BASE_1		0xF2000000
 #define CONFIG_SYS_PIGGY_BASE		0x80000000
 #define CONFIG_SYS_PAXE_BASE		0xA0000000
 #define	CONFIG_SYS_PAXE_SIZE		256

 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #else
 #undef	CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN		(128 * 1024) /* Reserved for malloc */

 /*
  * Initial RAM Base Address Setup
  */
 #define CONFIG_SYS_INIT_RAM_LOCK	1
 #define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000 /* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_END	0x1000 /* End of used area in RAM */
 #define CONFIG_SYS_GBL_DATA_SIZE	0x100 /* num bytes initial data */
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)

 /*
  * Local Bus Configuration & Clock Setup
  */
 #define CONFIG_SYS_LCRR		(LCRR_DBYP | LCRR_EADC_2 | LCRR_CLKDIV_4)

 /*
  * Init Local Bus Memory Controller:
  *
  * Bank Bus     Machine PortSz  Size  Device
  * ---- ---     ------- ------  -----  ------
  *  0   Local   GPCM    16 bit  256MB FLASH
  *  1   Local   GPCM     8 bit  256KB GPIO/PIGGY
  *  3   Local   GPCM     8 bit  256MB PAXE
  *
  */
 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
 #define CONFIG_FLASH_CFI_DRIVER		/* use the CFI driver */
 #define CONFIG_SYS_FLASH_SIZE		256 /* max FLASH size is 256M */
 #define CONFIG_SYS_FLASH_PROTECTION	1
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1

 #define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE /* Window base at flash base */
 #define CONFIG_SYS_LBLAWAR0_PRELIM	0x8000001b /* 256MB window size */

 #define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE | \
 				(2 << BR_PS_SHIFT) | /* 16 bit port size */ \
 				BR_V)

 #define CONFIG_SYS_OR0_PRELIM	(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) | \
 				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
 				OR_GPCM_SCY_5 | \
 				OR_GPCM_TRLX | OR_GPCM_EAD)

 #define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max num of flash banks	*/
 #define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sects on one chip */
 #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_1 }

 #undef	CONFIG_SYS_FLASH_CHECKSUM

 /*
  * PRIO1/PIGGY on the local bus CS1
  */
 #define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_PIGGY_BASE /* Window base at flash base */
 #define CONFIG_SYS_LBLAWAR1_PRELIM	0x80000011 /* 256KB window size */

 #define CONFIG_SYS_BR1_PRELIM	(CONFIG_SYS_PIGGY_BASE | \
 				(1 << BR_PS_SHIFT) | /* 8 bit port size */ \
 				BR_V)
 #define CONFIG_SYS_OR1_PRELIM		(0xfffc0000 | /* 256KB */ \
 				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
 				OR_GPCM_SCY_2 | \
 				OR_GPCM_TRLX | OR_GPCM_EAD)

 /*
  * PAXE on the local bus CS3
  */
 #define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_PAXE_BASE /* Window base at flash base */
 #define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000001b /* 256MB window size */

 #define CONFIG_SYS_BR3_PRELIM	(CONFIG_SYS_PAXE_BASE | \
 				(1 << BR_PS_SHIFT) | /* 8 bit port size */ \
 				BR_V)
 #define CONFIG_SYS_OR3_PRELIM	(MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) | \
 				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
 				OR_GPCM_SCY_2 | \
 				OR_GPCM_TRLX | OR_GPCM_EAD)

 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX	1
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
 #define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)

 /* Pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 #define CONFIG_OF_STDOUT_VIA_ALIAS

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #undef CONFIG_PCI		/* No PCI */

 #ifndef CONFIG_NET_MULTI
 #define CONFIG_NET_MULTI	1
 #endif
 /*
  * QE UEC ethernet configuration
  */
 #define CONFIG_UEC_ETH
 #define CONFIG_ETHPRIME		"FSL UEC0"

 #define CONFIG_UEC_ETH1		/* GETH1 */
 #define UEC_VERBOSE_DEBUG	1

 #ifdef CONFIG_UEC_ETH1
 #define CONFIG_SYS_UEC1_UCC_NUM	3	/* UCC4 */
 #define CONFIG_SYS_UEC1_RX_CLK		QE_CLK_NONE	/* not used in RMII Mode */
 #define CONFIG_SYS_UEC1_TX_CLK		QE_CLK17
 #define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
 #define CONFIG_SYS_UEC1_PHY_ADDR	0
 #define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII
 #endif

 /*
  * Environment
  */

 #ifndef CONFIG_SYS_RAMBOOT
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K(one sector) for env */
 #define CONFIG_ENV_SIZE		0x20000
 #define CONFIG_ENV_OFFSET	(CONFIG_SYS_MONITOR_LEN)

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

 #else /* CFG_RAMBOOT */
 #define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
 #define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
 #define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
 #define CONFIG_ENV_SIZE		0x2000
 #endif /* CFG_RAMBOOT */

 #if defined(CONFIG_PCI)
 #define CONFIG_CMD_PCI
 #endif

 #if defined(CFG_RAMBOOT)
 #undef CONFIG_CMD_ENV
 #undef CONFIG_CMD_LOADS
 #endif

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */

 /*
  * Core HID Setup
  */
 #define CONFIG_SYS_HID0_INIT		0x000000000
 #define CONFIG_SYS_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
 #define CONFIG_SYS_HID2			HID2_HBE

 /*
  * MMU Setup
  */

 #define CONFIG_HIGH_BATS	1	/* High BATs supported */

 /* DDR: cache cacheable */
 #define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | \
 				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
 #define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U

 /* IMMRBAR & PCI IO: cache-inhibit and guarded */
 #define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
 				BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
 #define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U

 /* PRIO1, PIGGY:  icache cacheable, but dcache-inhibit and guarded */
 #define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PIGGY_BASE | BATU_BL_256K | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT2L	(CONFIG_SYS_PIGGY_BASE | BATL_PP_10 | \
 				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U

 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 #define CONFIG_SYS_IBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT3U	(CONFIG_SYS_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT3L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
 				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U

 /* Stack in dcache: cacheable, no memory coherence */
 #define CONFIG_SYS_IBAT4L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
 #define CONFIG_SYS_IBAT4U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
 #define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U

 /* PAXE:  icache cacheable, but dcache-inhibit and guarded */
 #define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PAXE_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PAXE_BASE | BATU_BL_256K | BATU_VS | BATU_VP)
 #define CONFIG_SYS_DBAT5L	(CONFIG_SYS_PAXE_BASE | BATL_PP_10 | \
 				 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U

 #ifdef CONFIG_PCI
 /* PCI MEM space: cacheable */
 #define CFG_IBAT6L	(CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
 #define CFG_IBAT6U	(CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CFG_DBAT6L	CFG_IBAT6L
 #define CFG_DBAT6U	CFG_IBAT6U
 /* PCI MMIO space: cache-inhibit and guarded */
 #define CFG_IBAT7L	(CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
 			 BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 #define CFG_IBAT7U	(CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
 #define CFG_DBAT7L	CFG_IBAT7L
 #define CFG_DBAT7U	CFG_IBAT7U
 #else /* CONFIG_PCI */
 #define CONFIG_SYS_IBAT6L	(0)
 #define CONFIG_SYS_IBAT6U	(0)
 #define CONFIG_SYS_IBAT7L	(0)
 #define CONFIG_SYS_IBAT7U	(0)
 #define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
 #define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
 #define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
 #define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 #endif /* CONFIG_PCI */

 /*
  * Internal Definitions
  *
  * Boot Flags
  */
 #define BOOTFLAG_COLD	0x01 /* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02 /* Software reboot */

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_UEC_ETH)
 #define CONFIG_HAS_ETH0
 #endif

 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"netdev=eth0\0"							\
 	"rootpath=/opt/eldk/ppc_82xx\0"					\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs}"				\
 		" console=ttyS0,${baudrate}\0"				\
 	"fdt_addr=f0080000\0"						\
 	"kernel_addr=f00a0000\0"					\
 	"ramdisk_addr=f03a0000\0"					\
 	"kernel_addr_r=400000\0"					\
 	"fdt_addr_r=800000\0"						\
 	"ramdisk_addr_r=810000\0"					\
 	"flash_self=run ramargs addip addtty;"				\
 		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
 	"flash_nfs=run nfsargs addip addtty;"				\
 		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
 	"net_nfs=tftp ${kernel_addr_r} ${boot_file}; "			\
 		"tftp ${fdt_addr_r} ${fdt_file}; "			\
 		"run nfsargs addip addtty;"				\
 		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
 	"fdt_file=/tftpboot/kmeter1/kmeter1.dtb\0"			\
 	"boot_file=/tftpboot/kmeter1/uImage\0"				\
 	"ramdisk_file=/tftpboot/kmeter1/uRamdisk\0"			\
 	"u-boot=/tftpboot/kmeter1/u-boot.bin\0"				\
 	"loadaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0"			\
 	"load=tftp $loadaddr ${u-boot}\0"				\
 	"update=protect off " MK_STR(TEXT_BASE) " +$filesize;"		\
 		"erase " MK_STR(TEXT_BASE) " +$filesize;"		\
 		"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;"	\
 		"protect on " MK_STR(TEXT_BASE) " +$filesize;"		\
 		"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;"	\
 		"setenv filesize;saveenv\0"				\
 	"upd=run load update\0"						\
 	"loadram=tftp ${ramdisk_addr_r} ${ramdisk_file}\0"		\
 	"loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0"			\
 	"loadkernel=tftp ${kernel_addr_r} ${boot_file}\0"		\
 	"unlock=yes\0"							\
    ""

 #endif /* __CONFIG_H */
	/*
	* Copyright (C) 2006 Freescale Semiconductor, Inc.
	* Dave Liu <daveliu@freescale.com>
	*
	* Copyright (C) 2007 Logic Product Development, Inc.
	* Peter Barada <peterb@logicpd.com>
	*
	* Copyright (C) 2007 MontaVista Software, Inc.
	* Anton Vorontsov <avorontsov@ru.mvista.com>
	*
	* (C) Copyright 2008
	* Heiko Schocher, DENX Software Engineering, hs@denx.de.
	*
	* This program is free software; you can redistribute it and/or
	* modify it under the terms of the GNU General Public License as
	* published by the Free Software Foundation; either version 2 of
	* the License, or (at your option) any later version.
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_E300 1 /* E300 family */
	#define CONFIG_QE 1 /* Has QE */
	#define CONFIG_MPC83XX 1 /* MPC83XX family */
	#define CONFIG_MPC8360 1 /* MPC8360 CPU specific */
	#define CONFIG_KMETER1 1 /* KMETER1 board specific */

	/* include common defines/options for all Keymile boards */
	#include "keymile-common.h"

	/*
	* System Clock Setup
	*/
	#define CONFIG_83XX_CLKIN 66000000
	#define CONFIG_SYS_CLK_FREQ 66000000
	#define CONFIG_83XX_PCICLK 66000000

	/*
	* Hardware Reset Configuration Word
	*/
	#define CONFIG_SYS_HRCW_LOW (\
	HRCWL_CSB_TO_CLKIN_4X1 \| \
	HRCWL_CORE_TO_CSB_2X1 \| \
	HRCWL_CE_PLL_VCO_DIV_2 \| \
	HRCWL_CE_TO_PLL_1X6 )

	#define CONFIG_SYS_HRCW_HIGH (\
	HRCWH_CORE_ENABLE \| \
	HRCWH_FROM_0X00000100 \| \
	HRCWH_BOOTSEQ_NORMAL \| \
	HRCWH_SW_WATCHDOG_DISABLE \| \
	HRCWH_ROM_LOC_LOCAL_16BIT \| \
	HRCWH_BIG_ENDIAN \| \
	HRCWH_LDP_CLEAR )

	/*
	* System IO Config
	*/
	#define CONFIG_SYS_SICRH 0x00000006
	#define CONFIG_SYS_SICRL 0x00000000

	/*
	* IMMR new address
	*/
	#define CONFIG_SYS_IMMR 0xE0000000

	/*
	* DDR Setup
	*/
	#define CONFIG_SYS_DDR_BASE 0x00000000 /* DDR is system memory */
	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_BASE CONFIG_SYS_DDR_BASE
	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \| \
	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)

	#define CFG_83XX_DDR_USES_CS0

	#undef CONFIG_DDR_ECC

	/*
	* DDRCDR - DDR Control Driver Register
	*/

	#undef CONFIG_SPD_EEPROM /* Do not use SPD EEPROM for DDR setup */

	/*
	* Manually set up DDR parameters
	*/
	#define CONFIG_DDR_II
	#define CONFIG_SYS_DDR_SIZE 256 /* MB */
	#define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
	#define CONFIG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN \| CSCONFIG_AP \| \
	CSCONFIG_ROW_BIT_13 \| \
	CSCONFIG_COL_BIT_10 \| CSCONFIG_ODT_WR_ACS)

	#define CONFIG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SDRAM_TYPE_DDR2 \| \
	SDRAM_CFG_SREN)
	#define CONFIG_SYS_DDR_SDRAM_CFG2 0x00401000
	#define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
	#define CONFIG_SYS_DDR_INTERVAL ((0x100 << SDRAM_INTERVAL_BSTOPRE_SHIFT) \| \
	(0x406 << SDRAM_INTERVAL_REFINT_SHIFT))

	#define CONFIG_SYS_DDR_MODE 0x04440242
	#define CONFIG_SYS_DDR_MODE2 0x00800000

	#define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) \| \
	(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) \| \
	(6 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) \| \
	(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) \| \
	(0 << TIMING_CFG0_WWT_SHIFT) \| \
	(0 << TIMING_CFG0_RRT_SHIFT) \| \
	(0 << TIMING_CFG0_WRT_SHIFT) \| \
	(0 << TIMING_CFG0_RWT_SHIFT))

	#define CONFIG_SYS_DDR_TIMING_1 (( TIMING_CFG1_CASLAT_40) \| \
	( 2 << TIMING_CFG1_WRTORD_SHIFT) \| \
	( 1 << TIMING_CFG1_ACTTOACT_SHIFT) \| \
	( 2 << TIMING_CFG1_WRREC_SHIFT) \| \
	( 2 << TIMING_CFG1_REFREC_SHIFT) \| \
	( 2 << TIMING_CFG1_ACTTORW_SHIFT) \| \
	( 6 << TIMING_CFG1_ACTTOPRE_SHIFT) \| \
	( 2 << TIMING_CFG1_PRETOACT_SHIFT))

	#define CONFIG_SYS_DDR_TIMING_2 ((5 << TIMING_CFG2_FOUR_ACT_SHIFT) \| \
	(3 << TIMING_CFG2_CKE_PLS_SHIFT) \| \
	(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) \| \
	(1 << TIMING_CFG2_RD_TO_PRE_SHIFT) \| \
	(3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) \| \
	(0 << TIMING_CFG2_ADD_LAT_SHIFT) \| \
	(4 << TIMING_CFG2_CPO_SHIFT))

	#define CONFIG_SYS_DDR_TIMING_3 0x00000000

	/*
	* The reserved memory
	*/
	#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
	#define CONFIG_SYS_FLASH_BASE 0xF0000000
	#define CONFIG_SYS_FLASH_BASE_1 0xF2000000
	#define CONFIG_SYS_PIGGY_BASE 0x80000000
	#define CONFIG_SYS_PAXE_BASE 0xA0000000
	#define CONFIG_SYS_PAXE_SIZE 256

	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#else
	#undef CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserved for malloc */

	/*
	* Initial RAM Base Address Setup
	*/
	#define CONFIG_SYS_INIT_RAM_LOCK 1
	#define CONFIG_SYS_INIT_RAM_ADDR 0xE6000000 /* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_END 0x1000 /* End of used area in RAM */
	#define CONFIG_SYS_GBL_DATA_SIZE 0x100 /* num bytes initial data */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)

	/*
	* Local Bus Configuration & Clock Setup
	*/
	#define CONFIG_SYS_LCRR (LCRR_DBYP \| LCRR_EADC_2 \| LCRR_CLKDIV_4)

	/*
	* Init Local Bus Memory Controller:
	*
	* Bank Bus Machine PortSz Size Device
	* ---- --- ------- ------ ----- ------
	* 0 Local GPCM 16 bit 256MB FLASH
	* 1 Local GPCM 8 bit 256KB GPIO/PIGGY
	* 3 Local GPCM 8 bit 256MB PAXE
	*
	*/
	/*
	* FLASH on the Local Bus
	*/
	#define CONFIG_SYS_FLASH_CFI /* use the Common Flash Interface */
	#define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
	#define CONFIG_SYS_FLASH_SIZE 256 /* max FLASH size is 256M */
	#define CONFIG_SYS_FLASH_PROTECTION 1
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1

	#define CONFIG_SYS_LBLAWBAR0_PRELIM CONFIG_SYS_FLASH_BASE /* Window base at flash base */
	#define CONFIG_SYS_LBLAWAR0_PRELIM 0x8000001b /* 256MB window size */

	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| \
	(2 << BR_PS_SHIFT) \| /* 16 bit port size */ \
	BR_V)

	#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) \| \
	OR_GPCM_CSNT \| OR_GPCM_ACS_DIV2 \| \
	OR_GPCM_SCY_5 \| \
	OR_GPCM_TRLX \| OR_GPCM_EAD)

	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max num of sects on one chip */
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_1 }

	#undef CONFIG_SYS_FLASH_CHECKSUM

	/*
	* PRIO1/PIGGY on the local bus CS1
	*/
	#define CONFIG_SYS_LBLAWBAR1_PRELIM CONFIG_SYS_PIGGY_BASE /* Window base at flash base */
	#define CONFIG_SYS_LBLAWAR1_PRELIM 0x80000011 /* 256KB window size */

	#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_PIGGY_BASE \| \
	(1 << BR_PS_SHIFT) \| /* 8 bit port size */ \
	BR_V)
	#define CONFIG_SYS_OR1_PRELIM (0xfffc0000 \| /* 256KB */ \
	OR_GPCM_CSNT \| OR_GPCM_ACS_DIV2 \| \
	OR_GPCM_SCY_2 \| \
	OR_GPCM_TRLX \| OR_GPCM_EAD)

	/*
	* PAXE on the local bus CS3
	*/
	#define CONFIG_SYS_LBLAWBAR3_PRELIM CONFIG_SYS_PAXE_BASE /* Window base at flash base */
	#define CONFIG_SYS_LBLAWAR3_PRELIM 0x8000001b /* 256MB window size */

	#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_PAXE_BASE \| \
	(1 << BR_PS_SHIFT) \| /* 8 bit port size */ \
	BR_V)
	#define CONFIG_SYS_OR3_PRELIM (MEG_TO_AM(CONFIG_SYS_PAXE_SIZE) \| \
	OR_GPCM_CSNT \| OR_GPCM_ACS_DIV2 \| \
	OR_GPCM_SCY_2 \| \
	OR_GPCM_TRLX \| OR_GPCM_EAD)

	/*
	* Serial Port
	*/
	#define CONFIG_CONS_INDEX 1
	#undef CONFIG_SERIAL_SOFTWARE_FIFO
	#define CONFIG_SYS_NS16550
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

	/* Pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1
	#define CONFIG_OF_STDOUT_VIA_ALIAS

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#undef CONFIG_PCI /* No PCI */

	#ifndef CONFIG_NET_MULTI
	#define CONFIG_NET_MULTI 1
	#endif
	/*
	* QE UEC ethernet configuration
	*/
	#define CONFIG_UEC_ETH
	#define CONFIG_ETHPRIME "FSL UEC0"

	#define CONFIG_UEC_ETH1 /* GETH1 */
	#define UEC_VERBOSE_DEBUG 1

	#ifdef CONFIG_UEC_ETH1
	#define CONFIG_SYS_UEC1_UCC_NUM 3 /* UCC4 */
	#define CONFIG_SYS_UEC1_RX_CLK QE_CLK_NONE /* not used in RMII Mode */
	#define CONFIG_SYS_UEC1_TX_CLK QE_CLK17
	#define CONFIG_SYS_UEC1_ETH_TYPE FAST_ETH
	#define CONFIG_SYS_UEC1_PHY_ADDR 0
	#define CONFIG_SYS_UEC1_INTERFACE_MODE ENET_100_RMII
	#endif

	/*
	* Environment
	*/

	#ifndef CONFIG_SYS_RAMBOOT
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
	#define CONFIG_ENV_SIZE 0x20000
	#define CONFIG_ENV_OFFSET (CONFIG_SYS_MONITOR_LEN)

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)

	#else /* CFG_RAMBOOT */
	#define CONFIG_SYS_NO_FLASH 1 /* Flash is not usable now */
	#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
	#define CONFIG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE 0x2000
	#endif /* CFG_RAMBOOT */

	#if defined(CONFIG_PCI)
	#define CONFIG_CMD_PCI
	#endif

	#if defined(CFG_RAMBOOT)
	#undef CONFIG_CMD_ENV
	#undef CONFIG_CMD_LOADS
	#endif

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*
	* Core HID Setup
	*/
	#define CONFIG_SYS_HID0_INIT 0x000000000
	#define CONFIG_SYS_HID0_FINAL HID0_ENABLE_MACHINE_CHECK
	#define CONFIG_SYS_HID2 HID2_HBE

	/*
	* MMU Setup
	*/

	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	/* DDR: cache cacheable */
	#define CONFIG_SYS_IBAT0L (CONFIG_SYS_SDRAM_BASE \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT0U (CONFIG_SYS_SDRAM_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT0L CONFIG_SYS_IBAT0L
	#define CONFIG_SYS_DBAT0U CONFIG_SYS_IBAT0U

	/* IMMRBAR & PCI IO: cache-inhibit and guarded */
	#define CONFIG_SYS_IBAT1L (CONFIG_SYS_IMMR \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_IBAT1U (CONFIG_SYS_IMMR \| BATU_BL_4M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT1L CONFIG_SYS_IBAT1L
	#define CONFIG_SYS_DBAT1U CONFIG_SYS_IBAT1U

	/* PRIO1, PIGGY: icache cacheable, but dcache-inhibit and guarded */
	#define CONFIG_SYS_IBAT2L (CONFIG_SYS_PIGGY_BASE \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT2U (CONFIG_SYS_PIGGY_BASE \| BATU_BL_256K \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT2L (CONFIG_SYS_PIGGY_BASE \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT2U CONFIG_SYS_IBAT2U

	/* FLASH: icache cacheable, but dcache-inhibit and guarded */
	#define CONFIG_SYS_IBAT3L (CONFIG_SYS_FLASH_BASE \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT3U (CONFIG_SYS_FLASH_BASE \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT3L (CONFIG_SYS_FLASH_BASE \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT3U CONFIG_SYS_IBAT3U

	/* Stack in dcache: cacheable, no memory coherence */
	#define CONFIG_SYS_IBAT4L (CONFIG_SYS_INIT_RAM_ADDR \| BATL_PP_10)
	#define CONFIG_SYS_IBAT4U (CONFIG_SYS_INIT_RAM_ADDR \| BATU_BL_128K \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT4L CONFIG_SYS_IBAT4L
	#define CONFIG_SYS_DBAT4U CONFIG_SYS_IBAT4U

	/* PAXE: icache cacheable, but dcache-inhibit and guarded */
	#define CONFIG_SYS_IBAT5L (CONFIG_SYS_PAXE_BASE \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CONFIG_SYS_IBAT5U (CONFIG_SYS_PAXE_BASE \| BATU_BL_256K \| BATU_VS \| BATU_VP)
	#define CONFIG_SYS_DBAT5L (CONFIG_SYS_PAXE_BASE \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CONFIG_SYS_DBAT5U CONFIG_SYS_IBAT5U

	#ifdef CONFIG_PCI
	/* PCI MEM space: cacheable */
	#define CFG_IBAT6L (CFG_PCI1_MEM_PHYS \| BATL_PP_10 \| BATL_MEMCOHERENCE)
	#define CFG_IBAT6U (CFG_PCI1_MEM_PHYS \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT6L CFG_IBAT6L
	#define CFG_DBAT6U CFG_IBAT6U
	/* PCI MMIO space: cache-inhibit and guarded */
	#define CFG_IBAT7L (CFG_PCI1_MMIO_PHYS \| BATL_PP_10 \| \
	BATL_CACHEINHIBIT \| BATL_GUARDEDSTORAGE)
	#define CFG_IBAT7U (CFG_PCI1_MMIO_PHYS \| BATU_BL_256M \| BATU_VS \| BATU_VP)
	#define CFG_DBAT7L CFG_IBAT7L
	#define CFG_DBAT7U CFG_IBAT7U
	#else /* CONFIG_PCI */
	#define CONFIG_SYS_IBAT6L (0)
	#define CONFIG_SYS_IBAT6U (0)
	#define CONFIG_SYS_IBAT7L (0)
	#define CONFIG_SYS_IBAT7U (0)
	#define CONFIG_SYS_DBAT6L CONFIG_SYS_IBAT6L
	#define CONFIG_SYS_DBAT6U CONFIG_SYS_IBAT6U
	#define CONFIG_SYS_DBAT7L CONFIG_SYS_IBAT7L
	#define CONFIG_SYS_DBAT7U CONFIG_SYS_IBAT7U
	#endif /* CONFIG_PCI */

	/*
	* Internal Definitions
	*
	* Boot Flags
	*/
	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	#define BOOTFLAG_WARM 0x02 /* Software reboot */

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_UEC_ETH)
	#define CONFIG_HAS_ETH0
	#endif

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"rootpath=/opt/eldk/ppc_82xx\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addtty=setenv bootargs ${bootargs}" \
	" console=ttyS0,${baudrate}\0" \
	"fdt_addr=f0080000\0" \
	"kernel_addr=f00a0000\0" \
	"ramdisk_addr=f03a0000\0" \
	"kernel_addr_r=400000\0" \
	"fdt_addr_r=800000\0" \
	"ramdisk_addr_r=810000\0" \
	"flash_self=run ramargs addip addtty;" \
	"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \
	"flash_nfs=run nfsargs addip addtty;" \
	"bootm ${kernel_addr} - ${fdt_addr}\0" \
	"net_nfs=tftp ${kernel_addr_r} ${boot_file}; " \
	"tftp ${fdt_addr_r} ${fdt_file}; " \
	"run nfsargs addip addtty;" \
	"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
	"fdt_file=/tftpboot/kmeter1/kmeter1.dtb\0" \
	"boot_file=/tftpboot/kmeter1/uImage\0" \
	"ramdisk_file=/tftpboot/kmeter1/uRamdisk\0" \
	"u-boot=/tftpboot/kmeter1/u-boot.bin\0" \
	"loadaddr=" MK_STR(CONFIG_SYS_LOAD_ADDR) "\0" \
	"load=tftp $loadaddr ${u-boot}\0" \
	"update=protect off " MK_STR(TEXT_BASE) " +$filesize;" \
	"erase " MK_STR(TEXT_BASE) " +$filesize;" \
	"cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;" \
	"protect on " MK_STR(TEXT_BASE) " +$filesize;" \
	"cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize;" \
	"setenv filesize;saveenv\0" \
	"upd=run load update\0" \
	"loadram=tftp ${ramdisk_addr_r} ${ramdisk_file}\0" \
	"loadfdt=tftp ${fdt_addr_r} ${fdt_file}\0" \
	"loadkernel=tftp ${kernel_addr_r} ${boot_file}\0" \
	"unlock=yes\0" \
	""

	#endif /* __CONFIG_H */