e1000: Allow direct access to the E1000 SPI EEPROM device
As a part of the manufacturing process for some of our custom hardware,
we are programming the EEPROMs attached to our Intel 82571EB controllers
from software using U-Boot and Linux.
This code provides several conditionally-compiled features to assist in
our manufacturing process:
CONFIG_CMD_E1000:
This is a basic "e1000" command which allows querying the controller
and (if other config options are set) performing EEPROM programming.
In particular, with CONFIG_E1000_SPI this allows you to display a
hex-dump of the EEPROM, copy to/from main memory, and verify/update
the software checksum.
CONFIG_E1000_SPI_GENERIC:
Build a generic SPI driver providing the standard U-Boot SPI driver
interface. This allows commands such as "sspi" to access the bus
attached to the E1000 controller. Additionally, some E1000 chipsets
can support user data in a reserved space in the E1000 EEPROM which
could be used for U-Boot environment storage.
CONFIG_E1000_SPI:
The core SPI access code used by the above interfaces.
For example, the following commands allow you to program the EEPROM from
a USB device (assumes CONFIG_E1000_SPI and CONFIG_CMD_E1000 are enabled):
usb start
fatload usb 0 $loadaddr 82571EB_No_Mgmt_Discrete-LOM.bin
e1000 0 spi program $loadaddr 0 1024
e1000 0 spi checksum update
Please keep in mind that the Intel-provided .eep files are organized as
16-bit words. When converting them to binary form for programming you
must byteswap each 16-bit word so that it is in little-endian form.
This means that when reading and writing words to the SPI EEPROM, the
bit ordering for each word looks like this on the wire:
Time >>>
------------------------------------------------------------------
... [7, 6, 5, 4, 3, 2, 1, 0, 15, 14, 13, 12, 11, 10, 9, 8], ...
------------------------------------------------------------------
(MSB is 15, LSB is 0).
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
diff --git a/README b/README
index 58e582d..c05c40a 100644
--- a/README
+++ b/README
@@ -957,7 +957,20 @@
- NETWORK Support (PCI):
CONFIG_E1000
- Support for Intel 8254x gigabit chips.
+ Support for Intel 8254x/8257x gigabit chips.
+
+ CONFIG_E1000_SPI
+ Utility code for direct access to the SPI bus on Intel 8257x.
+ This does not do anything useful unless you set at least one
+ of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC.
+
+ CONFIG_E1000_SPI_GENERIC
+ Allow generic access to the SPI bus on the Intel 8257x, for
+ example with the "sspi" command.
+
+ CONFIG_CMD_E1000
+ Management command for E1000 devices. When used on devices
+ with SPI support you can reprogram the EEPROM from U-Boot.
CONFIG_E1000_FALLBACK_MAC
default MAC for empty EEPROM after production.
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 24eb361a..15eee8d 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -37,6 +37,7 @@
COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o
COBJS-$(CONFIG_DNET) += dnet.o
COBJS-$(CONFIG_E1000) += e1000.o
+COBJS-$(CONFIG_E1000_SPI) += e1000_spi.o
COBJS-$(CONFIG_EEPRO100) += eepro100.o
COBJS-$(CONFIG_ENC28J60) += enc28j60.o
COBJS-$(CONFIG_EP93XX) += ep93xx_eth.o
diff --git a/drivers/net/e1000.c b/drivers/net/e1000.c
index 7a6ecab..c86bf0a 100644
--- a/drivers/net/e1000.c
+++ b/drivers/net/e1000.c
@@ -5155,6 +5155,9 @@
}
}
+/* A list of all registered e1000 devices */
+static LIST_HEAD(e1000_hw_list);
+
/**************************************************************************
PROBE - Look for an adapter, this routine's visible to the outside
You should omit the last argument struct pci_device * for a non-PCI NIC
@@ -5234,8 +5237,9 @@
if (e1000_check_phy_reset_block(hw))
E1000_ERR(nic, "PHY Reset is blocked!\n");
- /* Basic init was OK, reset the hardware */
+ /* Basic init was OK, reset the hardware and allow SPI access */
e1000_reset_hw(hw);
+ list_add_tail(&hw->list_node, &e1000_hw_list);
/* Validate the EEPROM and get chipset information */
#if !(defined(CONFIG_AP1000) || defined(CONFIG_MVBC_1G))
@@ -5263,3 +5267,63 @@
return i;
}
+
+struct e1000_hw *e1000_find_card(unsigned int cardnum)
+{
+ struct e1000_hw *hw;
+
+ list_for_each_entry(hw, &e1000_hw_list, list_node)
+ if (hw->cardnum == cardnum)
+ return hw;
+
+ return NULL;
+}
+
+#ifdef CONFIG_CMD_E1000
+static int do_e1000(cmd_tbl_t *cmdtp, int flag,
+ int argc, char * const argv[])
+{
+ struct e1000_hw *hw;
+
+ if (argc < 3) {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ /* Make sure we can find the requested e1000 card */
+ hw = e1000_find_card(simple_strtoul(argv[1], NULL, 10));
+ if (!hw) {
+ printf("e1000: ERROR: No such device: e1000#%s\n", argv[1]);
+ return 1;
+ }
+
+ if (!strcmp(argv[2], "print-mac-address")) {
+ unsigned char *mac = hw->nic->enetaddr;
+ printf("%02x:%02x:%02x:%02x:%02x:%02x\n",
+ mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
+ return 0;
+ }
+
+#ifdef CONFIG_E1000_SPI
+ /* Handle the "SPI" subcommand */
+ if (!strcmp(argv[2], "spi"))
+ return do_e1000_spi(cmdtp, hw, argc - 3, argv + 3);
+#endif
+
+ cmd_usage(cmdtp);
+ return 1;
+}
+
+U_BOOT_CMD(
+ e1000, 7, 0, do_e1000,
+ "Intel e1000 controller management",
+ /* */"<card#> print-mac-address\n"
+#ifdef CONFIG_E1000_SPI
+ "e1000 <card#> spi show [<offset> [<length>]]\n"
+ "e1000 <card#> spi dump <addr> <offset> <length>\n"
+ "e1000 <card#> spi program <addr> <offset> <length>\n"
+ "e1000 <card#> spi checksum [update]\n"
+#endif
+ " - Manage the Intel E1000 PCI device"
+);
+#endif /* not CONFIG_CMD_E1000 */
diff --git a/drivers/net/e1000.h b/drivers/net/e1000.h
index fc5ed57..05f2bce 100644
--- a/drivers/net/e1000.h
+++ b/drivers/net/e1000.h
@@ -35,12 +35,17 @@
#define _E1000_HW_H_
#include <common.h>
+#include <linux/list.h>
#include <malloc.h>
#include <net.h>
#include <netdev.h>
#include <asm/io.h>
#include <pci.h>
+#ifdef CONFIG_E1000_SPI
+#include <spi.h>
+#endif
+
#define E1000_ERR(NIC, fmt, args...) \
printf("e1000: %s: ERROR: " fmt, (NIC)->name ,##args)
@@ -72,12 +77,18 @@
struct e1000_hw_stats;
/* Internal E1000 helper functions */
+struct e1000_hw *e1000_find_card(unsigned int cardnum);
int32_t e1000_acquire_eeprom(struct e1000_hw *hw);
void e1000_standby_eeprom(struct e1000_hw *hw);
void e1000_release_eeprom(struct e1000_hw *hw);
void e1000_raise_ee_clk(struct e1000_hw *hw, uint32_t *eecd);
void e1000_lower_ee_clk(struct e1000_hw *hw, uint32_t *eecd);
+#ifdef CONFIG_E1000_SPI
+int do_e1000_spi(cmd_tbl_t *cmdtp, struct e1000_hw *hw,
+ int argc, char * const argv[]);
+#endif
+
typedef enum {
FALSE = 0,
TRUE = 1
@@ -1068,7 +1079,11 @@
/* Structure containing variables used by the shared code (e1000_hw.c) */
struct e1000_hw {
+ struct list_head list_node;
struct eth_device *nic;
+#ifdef CONFIG_E1000_SPI
+ struct spi_slave spi;
+#endif
unsigned int cardnum;
pci_dev_t pdev;
diff --git a/drivers/net/e1000_spi.c b/drivers/net/e1000_spi.c
new file mode 100644
index 0000000..5491780
--- /dev/null
+++ b/drivers/net/e1000_spi.c
@@ -0,0 +1,576 @@
+#include "e1000.h"
+
+/*-----------------------------------------------------------------------
+ * SPI transfer
+ *
+ * This writes "bitlen" bits out the SPI MOSI port and simultaneously clocks
+ * "bitlen" bits in the SPI MISO port. That's just the way SPI works.
+ *
+ * The source of the outgoing bits is the "dout" parameter and the
+ * destination of the input bits is the "din" parameter. Note that "dout"
+ * and "din" can point to the same memory location, in which case the
+ * input data overwrites the output data (since both are buffered by
+ * temporary variables, this is OK).
+ *
+ * This may be interrupted with Ctrl-C if "intr" is true, otherwise it will
+ * never return an error.
+ */
+static int e1000_spi_xfer(struct e1000_hw *hw, unsigned int bitlen,
+ const void *dout_mem, void *din_mem, boolean_t intr)
+{
+ const uint8_t *dout = dout_mem;
+ uint8_t *din = din_mem;
+
+ uint8_t mask = 0;
+ uint32_t eecd;
+ unsigned long i;
+
+ /* Pre-read the control register */
+ eecd = E1000_READ_REG(hw, EECD);
+
+ /* Iterate over each bit */
+ for (i = 0, mask = 0x80; i < bitlen; i++, mask = (mask >> 1)?:0x80) {
+ /* Check for interrupt */
+ if (intr && ctrlc())
+ return -1;
+
+ /* Determine the output bit */
+ if (dout && dout[i >> 3] & mask)
+ eecd |= E1000_EECD_DI;
+ else
+ eecd &= ~E1000_EECD_DI;
+
+ /* Write the output bit and wait 50us */
+ E1000_WRITE_REG(hw, EECD, eecd);
+ E1000_WRITE_FLUSH(hw);
+ udelay(50);
+
+ /* Poke the clock (waits 50us) */
+ e1000_raise_ee_clk(hw, &eecd);
+
+ /* Now read the input bit */
+ eecd = E1000_READ_REG(hw, EECD);
+ if (din) {
+ if (eecd & E1000_EECD_DO)
+ din[i >> 3] |= mask;
+ else
+ din[i >> 3] &= ~mask;
+ }
+
+ /* Poke the clock again (waits 50us) */
+ e1000_lower_ee_clk(hw, &eecd);
+ }
+
+ /* Now clear any remaining bits of the input */
+ if (din && (i & 7))
+ din[i >> 3] &= ~((mask << 1) - 1);
+
+ return 0;
+}
+
+#ifdef CONFIG_E1000_SPI_GENERIC
+static inline struct e1000_hw *e1000_hw_from_spi(struct spi_slave *spi)
+{
+ return container_of(spi, struct e1000_hw, spi);
+}
+
+/* Not sure why all of these are necessary */
+void spi_init_r(void) { /* Nothing to do */ }
+void spi_init_f(void) { /* Nothing to do */ }
+void spi_init(void) { /* Nothing to do */ }
+
+struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
+ unsigned int max_hz, unsigned int mode)
+{
+ /* Find the right PCI device */
+ struct e1000_hw *hw = e1000_find_card(bus);
+ if (!hw) {
+ printf("ERROR: No such e1000 device: e1000#%u\n", bus);
+ return NULL;
+ }
+
+ /* Make sure it has an SPI chip */
+ if (hw->eeprom.type != e1000_eeprom_spi) {
+ E1000_ERR(hw->nic, "No attached SPI EEPROM found!\n");
+ return NULL;
+ }
+
+ /* Argument sanity checks */
+ if (cs != 0) {
+ E1000_ERR(hw->nic, "No such SPI chip: %u\n", cs);
+ return NULL;
+ }
+ if (mode != SPI_MODE_0) {
+ E1000_ERR(hw->nic, "Only SPI MODE-0 is supported!\n");
+ return NULL;
+ }
+
+ /* TODO: Use max_hz somehow */
+ E1000_DBG(hw->nic, "EEPROM SPI access requested\n");
+ return &hw->spi;
+}
+
+void spi_free_slave(struct spi_slave *spi)
+{
+ struct e1000_hw *hw = e1000_hw_from_spi(spi);
+ E1000_DBG(hw->nic, "EEPROM SPI access released\n");
+}
+
+int spi_claim_bus(struct spi_slave *spi)
+{
+ struct e1000_hw *hw = e1000_hw_from_spi(spi);
+
+ if (e1000_acquire_eeprom(hw)) {
+ E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n");
+ return -1;
+ }
+
+ return 0;
+}
+
+void spi_release_bus(struct spi_slave *spi)
+{
+ struct e1000_hw *hw = e1000_hw_from_spi(spi);
+ e1000_release_eeprom(hw);
+}
+
+/* Skinny wrapper around e1000_spi_xfer */
+int spi_xfer(struct spi_slave *spi, unsigned int bitlen,
+ const void *dout_mem, void *din_mem, unsigned long flags)
+{
+ struct e1000_hw *hw = e1000_hw_from_spi(spi);
+ int ret;
+
+ if (flags & SPI_XFER_BEGIN)
+ e1000_standby_eeprom(hw);
+
+ ret = e1000_spi_xfer(hw, bitlen, dout_mem, din_mem, TRUE);
+
+ if (flags & SPI_XFER_END)
+ e1000_standby_eeprom(hw);
+
+ return ret;
+}
+
+#endif /* not CONFIG_E1000_SPI_GENERIC */
+
+#ifdef CONFIG_CMD_E1000
+
+/* The EEPROM opcodes */
+#define SPI_EEPROM_ENABLE_WR 0x06
+#define SPI_EEPROM_DISABLE_WR 0x04
+#define SPI_EEPROM_WRITE_STATUS 0x01
+#define SPI_EEPROM_READ_STATUS 0x05
+#define SPI_EEPROM_WRITE_PAGE 0x02
+#define SPI_EEPROM_READ_PAGE 0x03
+
+/* The EEPROM status bits */
+#define SPI_EEPROM_STATUS_BUSY 0x01
+#define SPI_EEPROM_STATUS_WREN 0x02
+
+static int e1000_spi_eeprom_enable_wr(struct e1000_hw *hw, boolean_t intr)
+{
+ u8 op[] = { SPI_EEPROM_ENABLE_WR };
+ e1000_standby_eeprom(hw);
+ return e1000_spi_xfer(hw, 8*sizeof(op), op, NULL, intr);
+}
+
+/*
+ * These have been tested to perform correctly, but they are not used by any
+ * of the EEPROM commands at this time.
+ */
+#if 0
+static int e1000_spi_eeprom_disable_wr(struct e1000_hw *hw, boolean_t intr)
+{
+ u8 op[] = { SPI_EEPROM_DISABLE_WR };
+ e1000_standby_eeprom(hw);
+ return e1000_spi_xfer(hw, 8*sizeof(op), op, NULL, intr);
+}
+
+static int e1000_spi_eeprom_write_status(struct e1000_hw *hw,
+ u8 status, boolean_t intr)
+{
+ u8 op[] = { SPI_EEPROM_WRITE_STATUS, status };
+ e1000_standby_eeprom(hw);
+ return e1000_spi_xfer(hw, 8*sizeof(op), op, NULL, intr);
+}
+#endif
+
+static int e1000_spi_eeprom_read_status(struct e1000_hw *hw, boolean_t intr)
+{
+ u8 op[] = { SPI_EEPROM_READ_STATUS, 0 };
+ e1000_standby_eeprom(hw);
+ if (e1000_spi_xfer(hw, 8*sizeof(op), op, op, intr))
+ return -1;
+ return op[1];
+}
+
+static int e1000_spi_eeprom_write_page(struct e1000_hw *hw,
+ const void *data, u16 off, u16 len, boolean_t intr)
+{
+ u8 op[] = {
+ SPI_EEPROM_WRITE_PAGE,
+ (off >> (hw->eeprom.address_bits - 8)) & 0xff, off & 0xff
+ };
+
+ e1000_standby_eeprom(hw);
+
+ if (e1000_spi_xfer(hw, 8 + hw->eeprom.address_bits, op, NULL, intr))
+ return -1;
+ if (e1000_spi_xfer(hw, len << 3, data, NULL, intr))
+ return -1;
+
+ return 0;
+}
+
+static int e1000_spi_eeprom_read_page(struct e1000_hw *hw,
+ void *data, u16 off, u16 len, boolean_t intr)
+{
+ u8 op[] = {
+ SPI_EEPROM_READ_PAGE,
+ (off >> (hw->eeprom.address_bits - 8)) & 0xff, off & 0xff
+ };
+
+ e1000_standby_eeprom(hw);
+
+ if (e1000_spi_xfer(hw, 8 + hw->eeprom.address_bits, op, NULL, intr))
+ return -1;
+ if (e1000_spi_xfer(hw, len << 3, NULL, data, intr))
+ return -1;
+
+ return 0;
+}
+
+static int e1000_spi_eeprom_poll_ready(struct e1000_hw *hw, boolean_t intr)
+{
+ int status;
+ while ((status = e1000_spi_eeprom_read_status(hw, intr)) >= 0) {
+ if (!(status & SPI_EEPROM_STATUS_BUSY))
+ return 0;
+ }
+ return -1;
+}
+
+static int e1000_spi_eeprom_dump(struct e1000_hw *hw,
+ void *data, u16 off, unsigned int len, boolean_t intr)
+{
+ /* Interruptibly wait for the EEPROM to be ready */
+ if (e1000_spi_eeprom_poll_ready(hw, intr))
+ return -1;
+
+ /* Dump each page in sequence */
+ while (len) {
+ /* Calculate the data bytes on this page */
+ u16 pg_off = off & (hw->eeprom.page_size - 1);
+ u16 pg_len = hw->eeprom.page_size - pg_off;
+ if (pg_len > len)
+ pg_len = len;
+
+ /* Now dump the page */
+ if (e1000_spi_eeprom_read_page(hw, data, off, pg_len, intr))
+ return -1;
+
+ /* Otherwise go on to the next page */
+ len -= pg_len;
+ off += pg_len;
+ data += pg_len;
+ }
+
+ /* We're done! */
+ return 0;
+}
+
+static int e1000_spi_eeprom_program(struct e1000_hw *hw,
+ const void *data, u16 off, u16 len, boolean_t intr)
+{
+ /* Program each page in sequence */
+ while (len) {
+ /* Calculate the data bytes on this page */
+ u16 pg_off = off & (hw->eeprom.page_size - 1);
+ u16 pg_len = hw->eeprom.page_size - pg_off;
+ if (pg_len > len)
+ pg_len = len;
+
+ /* Interruptibly wait for the EEPROM to be ready */
+ if (e1000_spi_eeprom_poll_ready(hw, intr))
+ return -1;
+
+ /* Enable write access */
+ if (e1000_spi_eeprom_enable_wr(hw, intr))
+ return -1;
+
+ /* Now program the page */
+ if (e1000_spi_eeprom_write_page(hw, data, off, pg_len, intr))
+ return -1;
+
+ /* Otherwise go on to the next page */
+ len -= pg_len;
+ off += pg_len;
+ data += pg_len;
+ }
+
+ /* Wait for the last write to complete */
+ if (e1000_spi_eeprom_poll_ready(hw, intr))
+ return -1;
+
+ /* We're done! */
+ return 0;
+}
+
+static int do_e1000_spi_show(cmd_tbl_t *cmdtp, struct e1000_hw *hw,
+ int argc, char * const argv[])
+{
+ unsigned int length = 0;
+ u16 i, offset = 0;
+ u8 *buffer;
+ int err;
+
+ if (argc > 2) {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ /* Parse the offset and length */
+ if (argc >= 1)
+ offset = simple_strtoul(argv[0], NULL, 0);
+ if (argc == 2)
+ length = simple_strtoul(argv[1], NULL, 0);
+ else if (offset < (hw->eeprom.word_size << 1))
+ length = (hw->eeprom.word_size << 1) - offset;
+
+ /* Extra sanity checks */
+ if (!length) {
+ E1000_ERR(hw->nic, "Requested zero-sized dump!\n");
+ return 1;
+ }
+ if ((0x10000 < length) || (0x10000 - length < offset)) {
+ E1000_ERR(hw->nic, "Can't dump past 0xFFFF!\n");
+ return 1;
+ }
+
+ /* Allocate a buffer to hold stuff */
+ buffer = malloc(length);
+ if (!buffer) {
+ E1000_ERR(hw->nic, "Out of Memory!\n");
+ return 1;
+ }
+
+ /* Acquire the EEPROM and perform the dump */
+ if (e1000_acquire_eeprom(hw)) {
+ E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n");
+ free(buffer);
+ return 1;
+ }
+ err = e1000_spi_eeprom_dump(hw, buffer, offset, length, TRUE);
+ e1000_release_eeprom(hw);
+ if (err) {
+ E1000_ERR(hw->nic, "Interrupted!\n");
+ free(buffer);
+ return 1;
+ }
+
+ /* Now hexdump the result */
+ printf("%s: ===== Intel e1000 EEPROM (0x%04hX - 0x%04hX) =====",
+ hw->nic->name, offset, offset + length - 1);
+ for (i = 0; i < length; i++) {
+ if ((i & 0xF) == 0)
+ printf("\n%s: %04hX: ", hw->nic->name, offset + i);
+ else if ((i & 0xF) == 0x8)
+ printf(" ");
+ printf(" %02hx", buffer[i]);
+ }
+ printf("\n");
+
+ /* Success! */
+ free(buffer);
+ return 0;
+}
+
+static int do_e1000_spi_dump(cmd_tbl_t *cmdtp, struct e1000_hw *hw,
+ int argc, char * const argv[])
+{
+ unsigned int length;
+ u16 offset;
+ void *dest;
+
+ if (argc != 3) {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ /* Parse the arguments */
+ dest = (void *)simple_strtoul(argv[0], NULL, 16);
+ offset = simple_strtoul(argv[1], NULL, 0);
+ length = simple_strtoul(argv[2], NULL, 0);
+
+ /* Extra sanity checks */
+ if (!length) {
+ E1000_ERR(hw->nic, "Requested zero-sized dump!\n");
+ return 1;
+ }
+ if ((0x10000 < length) || (0x10000 - length < offset)) {
+ E1000_ERR(hw->nic, "Can't dump past 0xFFFF!\n");
+ return 1;
+ }
+
+ /* Acquire the EEPROM */
+ if (e1000_acquire_eeprom(hw)) {
+ E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n");
+ return 1;
+ }
+
+ /* Perform the programming operation */
+ if (e1000_spi_eeprom_dump(hw, dest, offset, length, TRUE) < 0) {
+ E1000_ERR(hw->nic, "Interrupted!\n");
+ e1000_release_eeprom(hw);
+ return 1;
+ }
+
+ e1000_release_eeprom(hw);
+ printf("%s: ===== EEPROM DUMP COMPLETE =====\n", hw->nic->name);
+ return 0;
+}
+
+static int do_e1000_spi_program(cmd_tbl_t *cmdtp, struct e1000_hw *hw,
+ int argc, char * const argv[])
+{
+ unsigned int length;
+ const void *source;
+ u16 offset;
+
+ if (argc != 3) {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ /* Parse the arguments */
+ source = (const void *)simple_strtoul(argv[0], NULL, 16);
+ offset = simple_strtoul(argv[1], NULL, 0);
+ length = simple_strtoul(argv[2], NULL, 0);
+
+ /* Acquire the EEPROM */
+ if (e1000_acquire_eeprom(hw)) {
+ E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n");
+ return 1;
+ }
+
+ /* Perform the programming operation */
+ if (e1000_spi_eeprom_program(hw, source, offset, length, TRUE) < 0) {
+ E1000_ERR(hw->nic, "Interrupted!\n");
+ e1000_release_eeprom(hw);
+ return 1;
+ }
+
+ e1000_release_eeprom(hw);
+ printf("%s: ===== EEPROM PROGRAMMED =====\n", hw->nic->name);
+ return 0;
+}
+
+static int do_e1000_spi_checksum(cmd_tbl_t *cmdtp, struct e1000_hw *hw,
+ int argc, char * const argv[])
+{
+ uint16_t i, length, checksum, checksum_reg;
+ uint16_t *buffer;
+ boolean_t upd;
+
+ if (argc == 0)
+ upd = 0;
+ else if ((argc == 1) && !strcmp(argv[0], "update"))
+ upd = 1;
+ else {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ /* Allocate a temporary buffer */
+ length = sizeof(uint16_t) * (EEPROM_CHECKSUM_REG + 1);
+ buffer = malloc(length);
+ if (!buffer) {
+ E1000_ERR(hw->nic, "Unable to allocate EEPROM buffer!\n");
+ return 1;
+ }
+
+ /* Acquire the EEPROM */
+ if (e1000_acquire_eeprom(hw)) {
+ E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n");
+ return 1;
+ }
+
+ /* Read the EEPROM */
+ if (e1000_spi_eeprom_dump(hw, buffer, 0, length, TRUE) < 0) {
+ E1000_ERR(hw->nic, "Interrupted!\n");
+ e1000_release_eeprom(hw);
+ return 1;
+ }
+
+ /* Compute the checksum and read the expected value */
+ for (i = 0; i < EEPROM_CHECKSUM_REG; i++)
+ checksum += le16_to_cpu(buffer[i]);
+ checksum = ((uint16_t)EEPROM_SUM) - checksum;
+ checksum_reg = le16_to_cpu(buffer[i]);
+
+ /* Verify it! */
+ if (checksum_reg == checksum) {
+ printf("%s: INFO: EEPROM checksum is correct! (0x%04hx)\n",
+ hw->nic->name, checksum);
+ e1000_release_eeprom(hw);
+ return 0;
+ }
+
+ /* Hrm, verification failed, print an error */
+ E1000_ERR(hw->nic, "EEPROM checksum is incorrect!\n");
+ E1000_ERR(hw->nic, " ...register was 0x%04hx, calculated 0x%04hx\n",
+ checksum_reg, checksum);
+
+ /* If they didn't ask us to update it, just return an error */
+ if (!upd) {
+ e1000_release_eeprom(hw);
+ return 1;
+ }
+
+ /* Ok, correct it! */
+ printf("%s: Reprogramming the EEPROM checksum...\n", hw->nic->name);
+ buffer[i] = cpu_to_le16(checksum);
+ if (e1000_spi_eeprom_program(hw, &buffer[i], i * sizeof(uint16_t),
+ sizeof(uint16_t), TRUE)) {
+ E1000_ERR(hw->nic, "Interrupted!\n");
+ e1000_release_eeprom(hw);
+ return 1;
+ }
+
+ e1000_release_eeprom(hw);
+ return 0;
+}
+
+int do_e1000_spi(cmd_tbl_t *cmdtp, struct e1000_hw *hw,
+ int argc, char * const argv[])
+{
+ if (argc < 1) {
+ cmd_usage(cmdtp);
+ return 1;
+ }
+
+ /* Make sure it has an SPI chip */
+ if (hw->eeprom.type != e1000_eeprom_spi) {
+ E1000_ERR(hw->nic, "No attached SPI EEPROM found!\n");
+ return 1;
+ }
+
+ /* Check the eeprom sub-sub-command arguments */
+ if (!strcmp(argv[0], "show"))
+ return do_e1000_spi_show(cmdtp, hw, argc - 1, argv + 1);
+
+ if (!strcmp(argv[0], "dump"))
+ return do_e1000_spi_dump(cmdtp, hw, argc - 1, argv + 1);
+
+ if (!strcmp(argv[0], "program"))
+ return do_e1000_spi_program(cmdtp, hw, argc - 1, argv + 1);
+
+ if (!strcmp(argv[0], "checksum"))
+ return do_e1000_spi_checksum(cmdtp, hw, argc - 1, argv + 1);
+
+ cmd_usage(cmdtp);
+ return 1;
+}
+
+#endif /* not CONFIG_CMD_E1000 */