board/BuR/brppt2: initial commit
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
diff --git a/board/BuR/brppt2/Kconfig b/board/BuR/brppt2/Kconfig
new file mode 100644
index 0000000..aa39d66
--- /dev/null
+++ b/board/BuR/brppt2/Kconfig
@@ -0,0 +1,18 @@
+if TARGET_BRPPT2
+
+config SYS_BOARD
+ default "brppt2"
+
+config SYS_VENDOR
+ default "BuR"
+
+config SYS_SOC
+ default "mx6"
+
+config SYS_CONFIG_NAME
+ default "brppt2"
+
+config SPL_DM_SPI
+ def_bool y
+
+endif
diff --git a/board/BuR/brppt2/MAINTAINERS b/board/BuR/brppt2/MAINTAINERS
new file mode 100644
index 0000000..a1b5bd4
--- /dev/null
+++ b/board/BuR/brppt2/MAINTAINERS
@@ -0,0 +1,6 @@
+BUR_PPT2 BOARD
+M: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
+S: Maintained
+F: board/BuR/brppt2/
+F: include/configs/brppt2.h
+F: configs/brppt2_defconfig
diff --git a/board/BuR/brppt2/Makefile b/board/BuR/brppt2/Makefile
new file mode 100644
index 0000000..7f3c7cd
--- /dev/null
+++ b/board/BuR/brppt2/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0+
+
+# Copyright (C) 2019
+# B&R Industrial Automation GmbH - http://www.br-automation.com
+#
+
+obj-y := ../common/common.o
+obj-y += board.o
diff --git a/board/BuR/brppt2/board.c b/board/BuR/brppt2/board.c
new file mode 100644
index 0000000..3284ff0
--- /dev/null
+++ b/board/BuR/brppt2/board.c
@@ -0,0 +1,542 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Board functions for BuR BRPPT2 board
+ *
+ * Copyright (C) 2019
+ * B&R Industrial Automation GmbH - http://www.br-automation.com/
+ *
+ */
+#include <common.h>
+#include <spl.h>
+#include <dm.h>
+#include <miiphy.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#ifdef CONFIG_SPL_BUILD
+# include <asm/arch/mx6-ddr.h>
+#endif
+#include <asm/arch/clock.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+
+#define USBHUB_RSTN IMX_GPIO_NR(1, 16)
+#define BKLT_EN IMX_GPIO_NR(1, 15)
+#define CAPT_INT IMX_GPIO_NR(4, 9)
+#define CAPT_RESETN IMX_GPIO_NR(4, 11)
+#define SW_INTN IMX_GPIO_NR(3, 26)
+#define VCCDISP_EN IMX_GPIO_NR(5, 18)
+#define EMMC_RSTN IMX_GPIO_NR(6, 8)
+#define PMIC_IRQN IMX_GPIO_NR(5, 22)
+#define TASTER IMX_GPIO_NR(5, 23)
+
+#define ETH0_LINK IMX_GPIO_NR(1, 27)
+#define ETH1_LINK IMX_GPIO_NR(1, 28)
+
+#define UART_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
+ PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define I2C_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
+ PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define ECSPI_PAD_CTRL (PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_48ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
+ PAD_CTL_SRE_FAST | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_60ohm | \
+ PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL1 (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_34ohm | \
+ PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_PU (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_80ohm | \
+ PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL_CLK ((PAD_CTL_PUS_100K_UP & ~PAD_CTL_PKE) | \
+ PAD_CTL_SPEED_MED | PAD_CTL_DSE_60ohm | \
+ PAD_CTL_SRE_FAST)
+
+#define GPIO_PAD_CTRL_PU (PAD_CTL_PUS_100K_UP | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
+ PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define GPIO_PAD_CTRL_PD (PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_48ohm | \
+ PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define LCDCMOS_PAD_CTRL (PAD_CTL_PUS_100K_DOWN | \
+ PAD_CTL_SPEED_LOW | PAD_CTL_DSE_120ohm |\
+ PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
+
+#define MUXDESC(pad, ctrl) IOMUX_PADS(pad | MUX_PAD_CTRL(ctrl))
+
+#if !defined(CONFIG_SPL_BUILD)
+static iomux_v3_cfg_t const eth_pads[] = {
+ /*
+ * Gigabit Ethernet
+ */
+ /* CLKs */
+ MUXDESC(PAD_GPIO_16__ENET_REF_CLK, ENET_PAD_CTRL_CLK),
+ MUXDESC(PAD_ENET_REF_CLK__ENET_TX_CLK, ENET_PAD_CTRL_CLK),
+ /* MDIO */
+ MUXDESC(PAD_ENET_MDIO__ENET_MDIO, ENET_PAD_CTRL_PU),
+ MUXDESC(PAD_ENET_MDC__ENET_MDC, ENET_PAD_CTRL_PU),
+ /* RGMII */
+ MUXDESC(PAD_RGMII_TXC__RGMII_TXC, ENET_PAD_CTRL1),
+ MUXDESC(PAD_RGMII_TD0__RGMII_TD0, ENET_PAD_CTRL),
+ MUXDESC(PAD_RGMII_TD1__RGMII_TD1, ENET_PAD_CTRL),
+ MUXDESC(PAD_RGMII_TD2__RGMII_TD2, ENET_PAD_CTRL),
+ MUXDESC(PAD_RGMII_TD3__RGMII_TD3, ENET_PAD_CTRL),
+ MUXDESC(PAD_RGMII_TX_CTL__RGMII_TX_CTL, ENET_PAD_CTRL),
+ MUXDESC(PAD_RGMII_RXC__RGMII_RXC, ENET_PAD_CTRL_PU),
+ MUXDESC(PAD_RGMII_RD0__RGMII_RD0, ENET_PAD_CTRL_PU),
+ MUXDESC(PAD_RGMII_RD1__RGMII_RD1, ENET_PAD_CTRL_PU),
+ MUXDESC(PAD_RGMII_RD2__RGMII_RD2, ENET_PAD_CTRL_PU),
+ MUXDESC(PAD_RGMII_RD3__RGMII_RD3, ENET_PAD_CTRL_PU),
+ MUXDESC(PAD_RGMII_RX_CTL__RGMII_RX_CTL, ENET_PAD_CTRL_PU),
+ /* ETH0_LINK */
+ MUXDESC(PAD_ENET_RXD0__GPIO1_IO27, GPIO_PAD_CTRL_PD),
+ /* ETH1_LINK */
+ MUXDESC(PAD_ENET_TX_EN__GPIO1_IO28, GPIO_PAD_CTRL_PD),
+};
+
+static iomux_v3_cfg_t const board_pads[] = {
+ /*
+ * I2C #3, #4
+ */
+ MUXDESC(PAD_GPIO_3__I2C3_SCL, I2C_PAD_CTRL),
+ MUXDESC(PAD_GPIO_6__I2C3_SDA, I2C_PAD_CTRL),
+
+ /*
+ * UART#4 PADS
+ * UART_Tasten
+ */
+ MUXDESC(PAD_CSI0_DAT12__UART4_TX_DATA, UART_PAD_CTRL),
+ MUXDESC(PAD_CSI0_DAT13__UART4_RX_DATA, UART_PAD_CTRL),
+ MUXDESC(PAD_CSI0_DAT17__UART4_CTS_B, UART_PAD_CTRL),
+ MUXDESC(PAD_CSI0_DAT16__UART4_RTS_B, UART_PAD_CTRL),
+ /*
+ * ESCPI#1
+ * M25P32 NOR-Flash
+ */
+ MUXDESC(PAD_EIM_D16__ECSPI1_SCLK, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_EIM_D17__ECSPI1_MISO, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_EIM_D18__ECSPI1_MOSI, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_EIM_D19__GPIO3_IO19, ECSPI_PAD_CTRL),
+ /*
+ * ESCPI#2
+ * resTouch SPI ADC
+ */
+ MUXDESC(PAD_CSI0_DAT8__ECSPI2_SCLK, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_EIM_OE__ECSPI2_MISO, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_CSI0_DAT9__ECSPI2_MOSI, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_EIM_D24__GPIO3_IO24, ECSPI_PAD_CTRL),
+ /*
+ * USDHC#4
+ */
+ MUXDESC(PAD_SD4_CLK__SD4_CLK, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_CMD__SD4_CMD, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT0__SD4_DATA0, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT1__SD4_DATA1, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT2__SD4_DATA2, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT3__SD4_DATA3, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT4__SD4_DATA4, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT5__SD4_DATA5, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT6__SD4_DATA6, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT7__SD4_DATA7, USDHC_PAD_CTRL),
+ /*
+ * USB OTG power & ID
+ */
+ /* USB_OTG_5V_EN */
+ MUXDESC(PAD_EIM_D22__GPIO3_IO22, GPIO_PAD_CTRL_PD),
+ MUXDESC(PAD_EIM_D31__GPIO3_IO31, GPIO_PAD_CTRL_PD),
+ /* USB_OTG_JUMPER */
+ MUXDESC(PAD_ENET_RX_ER__USB_OTG_ID, GPIO_PAD_CTRL_PD),
+ /*
+ * PWM-Pins
+ */
+ /* BKLT_CTL */
+ MUXDESC(PAD_SD1_CMD__PWM4_OUT, GPIO_PAD_CTRL_PD),
+ /* SPEAKER */
+ MUXDESC(PAD_SD1_DAT1__PWM3_OUT, GPIO_PAD_CTRL_PD),
+ /*
+ * GPIOs
+ */
+ /* USB_HUB_nRESET */
+ MUXDESC(PAD_SD1_DAT0__GPIO1_IO16, GPIO_PAD_CTRL_PD),
+ /* BKLT_EN */
+ MUXDESC(PAD_SD2_DAT0__GPIO1_IO15, GPIO_PAD_CTRL_PD),
+ /* capTouch_INT */
+ MUXDESC(PAD_KEY_ROW1__GPIO4_IO09, GPIO_PAD_CTRL_PD),
+ /* capTouch_nRESET */
+ MUXDESC(PAD_KEY_ROW2__GPIO4_IO11, GPIO_PAD_CTRL_PD),
+ /* SW_nINT */
+ MUXDESC(PAD_EIM_D26__GPIO3_IO26, GPIO_PAD_CTRL_PU),
+ /* VCC_DISP_EN */
+ MUXDESC(PAD_CSI0_PIXCLK__GPIO5_IO18, GPIO_PAD_CTRL_PD),
+ /* eMMC_nRESET */
+ MUXDESC(PAD_NANDF_ALE__GPIO6_IO08, GPIO_PAD_CTRL_PD),
+ /* HWID*/
+ MUXDESC(PAD_NANDF_D0__GPIO2_IO00, GPIO_PAD_CTRL_PU),
+ MUXDESC(PAD_NANDF_D1__GPIO2_IO01, GPIO_PAD_CTRL_PU),
+ MUXDESC(PAD_NANDF_D2__GPIO2_IO02, GPIO_PAD_CTRL_PU),
+ MUXDESC(PAD_NANDF_D3__GPIO2_IO03, GPIO_PAD_CTRL_PU),
+ /* PMIC_nIRQ */
+ MUXDESC(PAD_CSI0_DAT4__GPIO5_IO22, GPIO_PAD_CTRL_PU),
+ /* nTASTER */
+ MUXDESC(PAD_CSI0_DAT5__GPIO5_IO23, GPIO_PAD_CTRL_PU),
+ /* RGB LCD Display */
+ MUXDESC(PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DI0_PIN2__IPU1_DI0_PIN02, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DI0_PIN3__IPU1_DI0_PIN03, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DI0_PIN4__IPU1_DI0_PIN04, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DI0_PIN15__IPU1_DI0_PIN15, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT0__IPU1_DISP0_DATA00, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT1__IPU1_DISP0_DATA01, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT2__IPU1_DISP0_DATA02, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT3__IPU1_DISP0_DATA03, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT4__IPU1_DISP0_DATA04, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT5__IPU1_DISP0_DATA05, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT6__IPU1_DISP0_DATA06, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT7__IPU1_DISP0_DATA07, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT8__IPU1_DISP0_DATA08, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT9__IPU1_DISP0_DATA09, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT10__IPU1_DISP0_DATA10, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT11__IPU1_DISP0_DATA11, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT12__IPU1_DISP0_DATA12, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT13__IPU1_DISP0_DATA13, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT14__IPU1_DISP0_DATA14, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT15__IPU1_DISP0_DATA15, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT16__IPU1_DISP0_DATA16, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT17__IPU1_DISP0_DATA17, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT18__IPU1_DISP0_DATA18, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT19__IPU1_DISP0_DATA19, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT20__IPU1_DISP0_DATA20, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT21__IPU1_DISP0_DATA21, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT22__IPU1_DISP0_DATA22, LCDCMOS_PAD_CTRL),
+ MUXDESC(PAD_DISP0_DAT23__IPU1_DISP0_DATA23, LCDCMOS_PAD_CTRL),
+};
+
+int board_ehci_hcd_init(int port)
+{
+ gpio_direction_output(USBHUB_RSTN, 1);
+
+ return 0;
+}
+
+int board_late_init(void)
+{
+ ulong b_mode = 4;
+
+ if (gpio_get_value(TASTER) == 0)
+ b_mode = 12;
+
+ env_set_ulong("b_mode", b_mode);
+
+ return 0;
+}
+
+int board_init(void)
+{
+ gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
+
+ if (gpio_request(BKLT_EN, "BKLT_EN"))
+ printf("Warning: BKLT_EN setup failed\n");
+ gpio_direction_output(BKLT_EN, 0);
+
+ if (gpio_request(USBHUB_RSTN, "USBHUB_nRST"))
+ printf("Warning: USBHUB_nRST setup failed\n");
+ gpio_direction_output(USBHUB_RSTN, 0);
+
+ if (gpio_request(TASTER, "TASTER"))
+ printf("Warning: TASTER setup failed\n");
+ gpio_direction_input(TASTER);
+
+ return 0;
+}
+
+int board_early_init_f(void)
+{
+ struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+
+ SETUP_IOMUX_PADS(board_pads);
+ SETUP_IOMUX_PADS(eth_pads);
+
+ /* set GPIO_16 as ENET_REF_CLK_OUT running at 25 MHz */
+ setbits_le32(&iomux->gpr[1], IOMUXC_GPR1_ENET_CLK_SEL_MASK);
+ enable_fec_anatop_clock(0, ENET_25MHZ);
+ enable_enet_clk(1);
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ gd->ram_size = imx_ddr_size();
+
+ return 0;
+}
+#else
+/* configure MX6SOLO/DUALLITE mmdc DDR io registers */
+static struct mx6sdl_iomux_ddr_regs ddr_iomux_s = {
+ /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
+ .dram_sdclk_0 = 0x00020030,
+ .dram_sdclk_1 = 0x00020030,
+ .dram_cas = 0x00020030,
+ .dram_ras = 0x00020030,
+ .dram_reset = 0x00020030,
+ /* SDCKE[0:1]: 100k pull-up */
+ .dram_sdcke0 = 0x00003000,
+ .dram_sdcke1 = 0x00003000,
+ /* SDBA2: pull-up disabled */
+ .dram_sdba2 = 0x00000000,
+ /* SDODT[0:1]: 100k pull-up, 40 ohm */
+ .dram_sdodt0 = 0x00003030,
+ .dram_sdodt1 = 0x00003030,
+ /* SDQS[0:7]: Differential input, 40 ohm */
+ .dram_sdqs0 = 0x00000030,
+ .dram_sdqs1 = 0x00000030,
+ .dram_sdqs2 = 0x00000030,
+ .dram_sdqs3 = 0x00000030,
+ .dram_sdqs4 = 0x00000030,
+ .dram_sdqs5 = 0x00000030,
+ .dram_sdqs6 = 0x00000030,
+ .dram_sdqs7 = 0x00000030,
+ /* DQM[0:7]: Differential input, 40 ohm */
+ .dram_dqm0 = 0x00020030,
+ .dram_dqm1 = 0x00020030,
+ .dram_dqm2 = 0x00020030,
+ .dram_dqm3 = 0x00020030,
+ .dram_dqm4 = 0x00020030,
+ .dram_dqm5 = 0x00020030,
+ .dram_dqm6 = 0x00020030,
+ .dram_dqm7 = 0x00020030,
+};
+
+/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
+static struct mx6sdl_iomux_grp_regs grp_iomux_s = {
+ /* DDR3 */
+ .grp_ddr_type = 0x000c0000,
+ .grp_ddrmode_ctl = 0x00020000,
+ /* disable DDR pullups */
+ .grp_ddrpke = 0x00000000,
+ /* ADDR[00:16], SDBA[0:1]: 40 ohm */
+ .grp_addds = 0x00000030,
+ /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
+ .grp_ctlds = 0x00000030,
+ /* DATA[00:63]: Differential input, 40 ohm */
+ .grp_ddrmode = 0x00020000,
+ .grp_b0ds = 0x00000030,
+ .grp_b1ds = 0x00000030,
+ .grp_b2ds = 0x00000030,
+ .grp_b3ds = 0x00000030,
+ .grp_b4ds = 0x00000030,
+ .grp_b5ds = 0x00000030,
+ .grp_b6ds = 0x00000030,
+ .grp_b7ds = 0x00000030,
+};
+
+/*
+ * DDR3 desriptions - these are the memory chips we support
+ */
+
+/* NT5CC128M16FP-DII */
+static struct mx6_ddr3_cfg cfg_nt5cc128m16fp_dii = {
+ .mem_speed = 1600,
+ .density = 2,
+ .width = 16,
+ .banks = 8,
+ .rowaddr = 14,
+ .coladdr = 10,
+ .pagesz = 2,
+ .trcd = 1375,
+ .trcmin = 4875,
+ .trasmin = 3500,
+};
+
+/* measured on board TSERIES_ARM/1 V_LVDS_DL64 */
+static struct mx6_mmdc_calibration cal_nt5cc128m16fp_dii_128x64_s = {
+ /* write leveling calibration determine, MR1-value = 0x0002 */
+ .p0_mpwldectrl0 = 0x003F003E,
+ .p0_mpwldectrl1 = 0x003A003A,
+ .p1_mpwldectrl0 = 0x001B001C,
+ .p1_mpwldectrl1 = 0x00190031,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x02640264,
+ .p0_mpdgctrl1 = 0x02440250,
+ .p1_mpdgctrl0 = 0x02400250,
+ .p1_mpdgctrl1 = 0x0238023C,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x40464644,
+ .p1_mprddlctl = 0x464A4842,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x38343034,
+ .p1_mpwrdlctl = 0x36323830,
+};
+
+/* measured on board TSERIES_ARM/1 V_LVDS_S32 */
+static struct mx6_mmdc_calibration cal_nt5cc128m16fp_dii_128x32_s = {
+ /* write leveling calibration determine, MR1-value = 0x0002 */
+ .p0_mpwldectrl0 = 0x00410043,
+ .p0_mpwldectrl1 = 0x003A003C,
+ /* Read DQS Gating calibration */
+ .p0_mpdgctrl0 = 0x023C0244,
+ .p0_mpdgctrl1 = 0x02240230,
+ /* Read Calibration: DQS delay relative to DQ read access */
+ .p0_mprddlctl = 0x484C4A48,
+ /* Write Calibration: DQ/DM delay relative to DQS write access */
+ .p0_mpwrdlctl = 0x3C363434,
+};
+
+static void spl_dram_init(void)
+{
+ struct gpio_regs *gpio = (struct gpio_regs *)GPIO2_BASE_ADDR;
+ u32 val, dram_strap = 0;
+ struct mx6_ddr3_cfg *mem = NULL;
+ struct mx6_mmdc_calibration *calib = NULL;
+ struct mx6_ddr_sysinfo sysinfo = {
+ /* width of data bus:0=16,1=32,2=64 */
+ .dsize = -1, /* CPU type specific (overwritten) */
+ /* config for full 4GB range so that get_mem_size() works */
+ .cs_density = 32, /* 32Gb per CS */
+ .ncs = 1, /* single chip select */
+ .cs1_mirror = 0,
+ .rtt_wr = 1, /* DDR3_RTT_60_OHM, RTT_Wr = RZQ/4 */
+ .rtt_nom = 1, /* DDR3_RTT_60_OHM, RTT_Nom = RZQ/4 */
+ .walat = 1, /* Write additional latency */
+ .ralat = 5, /* Read additional latency */
+ .mif3_mode = 3, /* Command prediction working mode */
+ .bi_on = 1, /* Bank interleaving enabled */
+ .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
+ .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
+ .ddr_type = 0, /* DDR3 */
+ };
+
+ /*
+ * MMDC Calibration requires the following data:
+ * mx6_mmdc_calibration - board-specific calibration (routing delays)
+ * these calibration values depend on board routing, SoC, and DDR
+ * mx6_ddr_sysinfo - board-specific memory architecture (width/cs/etc)
+ * mx6_ddr_cfg - chip specific timing/layout details
+ */
+
+ /* setup HWID3-2 to input */
+ val = readl(&gpio->gpio_dir);
+ val &= ~(0x1 << 0 | 0x1 << 1);
+ writel(val, &gpio->gpio_dir);
+
+ /* read DRAM strapping from HWID3/2 (bit 1 and bit 0) */
+ dram_strap = readl(&gpio->gpio_psr) & 0x3;
+
+ switch (dram_strap) {
+ /* 1 GiB, 64 bit, 4 NT5CC128M16FP chips */
+ case 0:
+ puts("DRAM strap 00\n");
+ mem = &cfg_nt5cc128m16fp_dii;
+ sysinfo.dsize = 2;
+ calib = &cal_nt5cc128m16fp_dii_128x64_s;
+ break;
+ /* 512 MiB, 32 bit, 2 NT5CC128M16FP chips */
+ case 1:
+ puts("DRAM strap 01\n");
+ mem = &cfg_nt5cc128m16fp_dii;
+ sysinfo.dsize = 1;
+ calib = &cal_nt5cc128m16fp_dii_128x32_s;
+ break;
+ default:
+ printf("DRAM strap 0x%x (invalid)\n", dram_strap);
+ break;
+ }
+
+ if (!mem) {
+ puts("Error: Invalid Memory Configuration\n");
+ hang();
+ }
+ if (!calib) {
+ puts("Error: Invalid Board Calibration Configuration\n");
+ hang();
+ }
+
+ mx6sdl_dram_iocfg(16 << sysinfo.dsize,
+ &ddr_iomux_s,
+ &grp_iomux_s);
+
+ mx6_dram_cfg(&sysinfo, calib, mem);
+}
+
+static iomux_v3_cfg_t const board_pads_spl[] = {
+ /* UART#1 PADS */
+ MUXDESC(PAD_CSI0_DAT10__UART1_TX_DATA, UART_PAD_CTRL),
+ MUXDESC(PAD_CSI0_DAT11__UART1_RX_DATA, UART_PAD_CTRL),
+ /* ESCPI#1 PADS */
+ MUXDESC(PAD_EIM_D16__ECSPI1_SCLK, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_EIM_D17__ECSPI1_MISO, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_EIM_D18__ECSPI1_MOSI, ECSPI_PAD_CTRL),
+ MUXDESC(PAD_EIM_D19__GPIO3_IO19, ECSPI_PAD_CTRL),
+ /* USDHC#4 PADS */
+ MUXDESC(PAD_SD4_CLK__SD4_CLK, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_CMD__SD4_CMD, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT0__SD4_DATA0, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT1__SD4_DATA1, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT2__SD4_DATA2, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT3__SD4_DATA3, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT4__SD4_DATA4, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT5__SD4_DATA5, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT6__SD4_DATA6, USDHC_PAD_CTRL),
+ MUXDESC(PAD_SD4_DAT7__SD4_DATA7, USDHC_PAD_CTRL),
+ /* HWID*/
+ MUXDESC(PAD_NANDF_D0__GPIO2_IO00, GPIO_PAD_CTRL_PU),
+ MUXDESC(PAD_NANDF_D1__GPIO2_IO01, GPIO_PAD_CTRL_PU),
+ MUXDESC(PAD_NANDF_D2__GPIO2_IO02, GPIO_PAD_CTRL_PU),
+ MUXDESC(PAD_NANDF_D3__GPIO2_IO03, GPIO_PAD_CTRL_PU),
+};
+
+void spl_board_init(void)
+{
+ preloader_console_init();
+}
+
+static void ccgr_init(void)
+{
+ struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+ /*
+ * We don't use DMA in SPL, but we do need it in U-Boot. U-Boot
+ * initializes DMA very early (before all board code), so the only
+ * opportunity we have to initialize APBHDMA clocks is in SPL.
+ * setbits_le32(&ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+ */
+
+ writel(0x00C03F3F, &ccm->CCGR0);
+ writel(0x00F0FC03, &ccm->CCGR1);
+ writel(0x0FFFF000, &ccm->CCGR2);
+ writel(0x3FF00000, &ccm->CCGR3);
+ writel(0x00FFF300, &ccm->CCGR4);
+ writel(0x0F0030C3, &ccm->CCGR5);
+ writel(0x000003F0, &ccm->CCGR6);
+}
+
+void board_init_f(ulong dummy)
+{
+ ccgr_init();
+ arch_cpu_init();
+ timer_init();
+ gpr_init();
+
+ SETUP_IOMUX_PADS(board_pads_spl);
+ spl_dram_init();
+}
+
+void reset_cpu(ulong addr)
+{
+}
+#endif /* CONFIG_SPL_BUILD */
diff --git a/board/BuR/brppt2/config.mk b/board/BuR/brppt2/config.mk
new file mode 100644
index 0000000..fa973db
--- /dev/null
+++ b/board/BuR/brppt2/config.mk
@@ -0,0 +1,36 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2019 Hannes Schmelzer <oe5hpm@oevsv.at> -
+# B&R Industrial Automation GmbH - http://www.br-automation.com
+#
+
+hw-platform-y :=$(shell echo $(CONFIG_DEFAULT_DEVICE_TREE) | sed -e 's/imx6dl-//')
+
+payload_off :=$(shell printf "%d" $(CONFIG_SYS_SPI_U_BOOT_OFFS))
+
+quiet_cmd_prodbin = PRODBIN $@ $(payload_off)
+cmd_prodbin = \
+ dd if=/dev/zero ibs=1M count=2 2>/dev/null | tr "\000" "\377" >$@ && \
+ dd conv=notrunc bs=1 if=SPL of=$@ seek=1024 2>/dev/null && \
+ dd bs=1 if=u-boot-dtb.img of=$@ seek=$(payload_off) 2>/dev/null
+
+quiet_cmd_prodzip = SAPZIP $@
+cmd_prodzip = \
+ test -d misc && rm -r misc; \
+ mkdir misc && \
+ cp SPL misc/ && \
+ cp u-boot-dtb.img misc/ && \
+ zip -9 -r $@ misc/* >/dev/null $<
+
+ifeq ($(hw-platform-y),brppt2)
+ifneq ($(CONFIG_SPL_BUILD),y)
+ALL-y += $(hw-platform-y)_prog.bin
+ALL-y += $(hw-platform-y)_prod.zip
+endif
+endif
+
+$(hw-platform-y)_prog.bin: u-boot-dtb.img spl SPL
+ $(call if_changed,prodbin)
+
+$(hw-platform-y)_prod.zip: $(hw-platform-y)_prog.bin
+ $(call if_changed,prodzip)