diff --git a/board/thecus/n2350/MAINTAINERS b/board/thecus/n2350/MAINTAINERS
new file mode 100644
index 0000000..2b8774f
--- /dev/null
+++ b/board/thecus/n2350/MAINTAINERS
@@ -0,0 +1,7 @@
+N2350  BOARD
+M:	Tony Dinh <mibodhi@gmail.com>
+S:	Maintained
+F:	arch/arm/dts/armada-385-thecus-n2350.dts
+F:	board/thecus/n2350/
+F:	include/configs/n2350.h
+F:	configs/n2350_defconfig
diff --git a/board/thecus/n2350/Makefile b/board/thecus/n2350/Makefile
new file mode 100644
index 0000000..b220bb1
--- /dev/null
+++ b/board/thecus/n2350/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0+
+#
+# Copyright (C) 2023 Tony Dinh <mibodhi@gmail.com>
+#
+
+obj-y	:= n2350.o
diff --git a/board/thecus/n2350/n2350.c b/board/thecus/n2350/n2350.c
new file mode 100644
index 0000000..4cfdfba
--- /dev/null
+++ b/board/thecus/n2350/n2350.c
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2023 Tony Dinh <mibodhi@gmail.com>
+ *
+ */
+
+#include <i2c.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/io.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/soc.h>
+#include <linux/bitops.h>
+
+#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
+#include <../serdes/a38x/high_speed_env_spec.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+/*
+ * Those N2350_GPP_xx values and defines in board_serdes_map, and board_topology_map
+ * are taken from the Marvell U-Boot version "u-boot-a38x-2015T1_p18_Thecus"
+ */
+
+#define N2350_GPP_OUT_ENA_LOW	(~(BIT(20) | BIT(21) | BIT(24)))
+#define N2350_GPP_OUT_ENA_MID	(~(BIT(12) | BIT(13) | BIT(16) | BIT(19) | BIT(22)))
+#define N2350_GPP_OUT_VAL_LOW	0x1200000
+#define N2350_GPP_OUT_VAL_MID	0x1001
+#define N2350_GPP_POL_LOW	0x0
+#define N2350_GPP_POL_MID	0x0
+
+static struct serdes_map board_serdes_map[] = {
+	{ SGMII0, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{ SATA0,  SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{ SATA1,  SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{ DEFAULT_SERDES, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{ USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+	{ USB3_HOST1, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
+};
+
+int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
+{
+	*serdes_map_array = board_serdes_map;
+	*count = ARRAY_SIZE(board_serdes_map);
+	return 0;
+}
+
+/*
+ * Define the DDR layout / topology here in the board file. This will
+ * be used by the DDR4 init code in the SPL U-Boot version to configure
+ * the DDR4 controller.
+ */
+
+static struct mv_ddr_topology_map board_topology_map = {
+	DEBUG_LEVEL_ERROR,
+	0x1, /* active interfaces */
+	/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
+	{ { { {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0},
+	      {0x1, 0, 0, 0} },
+	    SPEED_BIN_DDR_1866L,        /* speed_bin */
+	    MV_DDR_DEV_WIDTH_16BIT,     /* memory_width - 16 bits */
+	    MV_DDR_DIE_CAP_4GBIT,       /* mem_size - N2350 board has 2x512MB DRAM banks */
+	    MV_DDR_FREQ_800,            /* frequency */
+	    0, 0,			/* cas_wl cas_l */
+	    MV_DDR_TEMP_LOW,		/* temperature */
+	    MV_DDR_TIM_DEFAULT} },	/* timing */
+	BUS_MASK_32BIT,			/* Busses mask */
+	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
+	NOT_COMBINED,			/* ddr twin-die combined */
+	{ {0} },			/* raw spd data */
+	{0}				/* timing parameters */
+};
+
+struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
+{
+	/* Return the board topology as defined in the board code */
+	return &board_topology_map;
+}
+
+int board_early_init_f(void)
+{
+	/* Those MPP values are taken from the Marvell U-Boot version
+	 * "u-boot-a38x-2015T1_p18_Thecus"
+	 */
+
+	/* Configure MPP */
+	writel(0x50111111, MVEBU_MPP_BASE + 0x00);	/* MPP0_7 */
+	writel(0x00555555, MVEBU_MPP_BASE + 0x04);	/* MPP8_15 */
+	writel(0x55000000, MVEBU_MPP_BASE + 0x08);	/* MPP16_23 */
+	writel(0x05050050, MVEBU_MPP_BASE + 0x0c);	/* MPP24_31 */
+	writel(0x05555555, MVEBU_MPP_BASE + 0x10);	/* MPP32_39 */
+	writel(0x00000565, MVEBU_MPP_BASE + 0x14);	/* MPP40_47 */
+	writel(0x00000000, MVEBU_MPP_BASE + 0x18);	/* MPP48_55 */
+	writel(0x00004444, MVEBU_MPP_BASE + 0x1c);	/* MPP56_63 */
+
+	/* Set GPP Out value */
+	writel(N2350_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
+	writel(N2350_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);
+
+	/* Set GPP Polarity */
+	writel(N2350_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
+	writel(N2350_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);
+
+	/* Set GPP Out Enable */
+	writel(N2350_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
+	writel(N2350_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
+
+	return 0;
+}
+
+int board_eth_init(struct bd_info *bis)
+{
+	cpu_eth_init(bis); /* Built in controller(s) come first */
+	return pci_eth_init(bis);
+}