arm: dts: k3-j721e: Sync Linux v5.11-rc6 dts into U-Boot
Sync all J721e related v5.11-rc6 Linux kernel dts into U-Boot.
HBMC nodes are not yet added in Linux kernel yet but were added
in U-Boot. In order to avoid any regressions, hbmc nodes are kept
intact. These will be added in kernel in future.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
diff --git a/arch/arm/dts/k3-j721e-common-proc-board.dts b/arch/arm/dts/k3-j721e-common-proc-board.dts
index fcfc665..6076436 100644
--- a/arch/arm/dts/k3-j721e-common-proc-board.dts
+++ b/arch/arm/dts/k3-j721e-common-proc-board.dts
@@ -1,12 +1,14 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
*/
/dts-v1/;
#include "k3-j721e-som-p0.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/net/ti-dp83867.h>
/ {
chosen {
@@ -14,16 +16,55 @@
bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
};
- aliases {
- remoteproc0 = &mcu_r5fss0_core0;
- remoteproc1 = &mcu_r5fss0_core1;
- remoteproc2 = &main_r5fss0_core0;
- remoteproc3 = &main_r5fss0_core1;
- remoteproc4 = &main_r5fss1_core0;
- remoteproc5 = &main_r5fss1_core1;
- remoteproc6 = &c66_0;
- remoteproc7 = &c66_1;
- remoteproc8 = &c71_0;
+ gpio_keys: gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw10_button_pins_default &sw11_button_pins_default>;
+
+ sw10: sw10 {
+ label = "GPIO Key USER1";
+ linux,code = <BTN_0>;
+ gpios = <&main_gpio0 0 GPIO_ACTIVE_LOW>;
+ };
+
+ sw11: sw11 {
+ label = "GPIO Key USER2";
+ linux,code = <BTN_1>;
+ gpios = <&wkup_gpio0 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ evm_12v0: fixedregulator-evm12v0 {
+ /* main supply */
+ compatible = "regulator-fixed";
+ regulator-name = "evm_12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_3v3: fixedregulator-vsys3v3 {
+ /* Output of LMS140 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_5v0: fixedregulator-vsys5v0 {
+ /* Output of LM5140 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
};
vdd_mmc1: fixedregulator-sd {
@@ -33,6 +74,7 @@
regulator-max-microvolt = <3300000>;
regulator-boot-on;
enable-active-high;
+ vin-supply = <&vsys_3v3>;
gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
};
@@ -44,15 +86,173 @@
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
+ vin-supply = <&vsys_5v0>;
gpios = <&main_gpio0 117 GPIO_ACTIVE_HIGH>;
- states = <1800000 0x0
- 3300000 0x1>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
+
+ sound0: sound@0 {
+ compatible = "ti,j721e-cpb-audio";
+ model = "j721e-cpb";
+
+ ti,cpb-mcasp = <&mcasp10>;
+ ti,cpb-codec = <&pcm3168a_1>;
+
+ clocks = <&k3_clks 184 1>,
+ <&k3_clks 184 2>, <&k3_clks 184 4>,
+ <&k3_clks 157 371>,
+ <&k3_clks 157 400>, <&k3_clks 157 401>;
+ clock-names = "cpb-mcasp-auxclk",
+ "cpb-mcasp-auxclk-48000", "cpb-mcasp-auxclk-44100",
+ "cpb-codec-scki",
+ "cpb-codec-scki-48000", "cpb-codec-scki-44100";
+ };
+};
+
+&main_pmx0 {
+ sw10_button_pins_default: sw10-button-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
+ >;
+ };
+
+ main_mmc1_pins_default: main-mmc1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
+ J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
+ J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
+ J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
+ J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+ J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
+ J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
+ J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
+ J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */
+ >;
+ };
+
+ vdd_sd_dv_alt_pins_default: vdd-sd-dv-alt-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1d8, PIN_INPUT, 7) /* (W4) SPI1_CS1.GPIO0_117 */
+ >;
+ };
+
+ main_usbss0_pins_default: main-usbss0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
+ J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
+ >;
+ };
+
+ main_usbss1_pins_default: main-usbss1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
+ >;
+ };
+
+ main_i2c1_exp4_pins_default: main-i2c1-exp4-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */
+ >;
+ };
+
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
+ J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
+ >;
+ };
+
+ main_i2c1_pins_default: main-i2c1-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (Y6) I2C1_SCL */
+ J721E_IOPAD(0x22c, PIN_INPUT_PULLUP, 0) /* (AA6) I2C1_SDA */
+ >;
+ };
+
+ main_i2c3_pins_default: main-i2c3-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x270, PIN_INPUT_PULLUP, 4) /* (T26) MMC2_CLK.I2C3_SCL */
+ J721E_IOPAD(0x274, PIN_INPUT_PULLUP, 4) /* (T25) MMC2_CMD.I2C3_SDA */
+ >;
+ };
+
+ main_i2c6_pins_default: main-i2c6-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1d0, PIN_INPUT_PULLUP, 2) /* (AA3) SPI0_D1.I2C6_SCL */
+ J721E_IOPAD(0x1e4, PIN_INPUT_PULLUP, 2) /* (Y2) SPI1_D1.I2C6_SDA */
+ >;
+ };
+
+ mcasp10_pins_default: mcasp10-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
+ J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
+ J721E_IOPAD(0x160, PIN_OUTPUT_PULLDOWN, 12) /* (V28) RGMII5_TD3.MCASP10_AXR0 */
+ J721E_IOPAD(0x164, PIN_OUTPUT_PULLDOWN, 12) /* (V29) RGMII5_TD2.MCASP10_AXR1 */
+ J721E_IOPAD(0x170, PIN_OUTPUT_PULLDOWN, 12) /* (U29) RGMII5_TXC.MCASP10_AXR2 */
+ J721E_IOPAD(0x174, PIN_OUTPUT_PULLDOWN, 12) /* (U25) RGMII5_RXC.MCASP10_AXR3 */
+ J721E_IOPAD(0x198, PIN_INPUT_PULLDOWN, 12) /* (V25) RGMII6_TD1.MCASP10_AXR4 */
+ J721E_IOPAD(0x19c, PIN_INPUT_PULLDOWN, 12) /* (W27) RGMII6_TD0.MCASP10_AXR5 */
+ J721E_IOPAD(0x1a0, PIN_INPUT_PULLDOWN, 12) /* (W29) RGMII6_TXC.MCASP10_AXR6 */
+ >;
+ };
+
+ audi_ext_refclk2_pins_default: audi-ext-refclk2-pins-default {
+ pinctrl-single,pins = <
+ J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
+ >;
};
};
+&wkup_pmx0 {
+ sw11_button_pins_default: sw11-button-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
+ >;
+ };
+
+ mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x34, PIN_OUTPUT, 0) /* (F22) MCU_OSPI1_CLK */
+ J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (C22) MCU_OSPI1_CSn0 */
+ J721E_WKUP_IOPAD(0x40, PIN_INPUT, 0) /* (D22) MCU_OSPI1_D0 */
+ J721E_WKUP_IOPAD(0x44, PIN_INPUT, 0) /* (G22) MCU_OSPI1_D1 */
+ J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (D23) MCU_OSPI1_D2 */
+ J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
+ J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
+ J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
+ >;
+ };
+
+ mcu_cpsw_pins_default: mcu-cpsw-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
+ J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
+ J721E_WKUP_IOPAD(0x0060, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
+ J721E_WKUP_IOPAD(0x0064, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
+ J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
+ J721E_WKUP_IOPAD(0x006c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
+ J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
+ J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
+ J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
+ J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
+ J721E_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+ J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
+ >;
+ };
+
+ mcu_mdio_pins_default: mcu-mdio1-pins-default {
+ pinctrl-single,pins = <
+ J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
+ J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
+ >;
+ };
+};
+
&wkup_uart0 {
/* Wakeup UART is used by System firmware */
- status = "disabled";
+ status = "reserved";
};
&main_uart0 {
@@ -89,84 +289,81 @@
status = "disabled";
};
-&main_pmx0 {
- main_mmc1_pins_default: main_mmc1_pins_default {
- pinctrl-single,pins = <
- J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
- J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
- J721E_IOPAD(0x2ac, PIN_INPUT, 0) /* (P25) MMC1_CLKLB */
- J721E_IOPAD(0x24c, PIN_INPUT, 0) /* (R24) MMC1_DAT0 */
- J721E_IOPAD(0x248, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
- J721E_IOPAD(0x244, PIN_INPUT, 0) /* (R25) MMC1_DAT2 */
- J721E_IOPAD(0x240, PIN_INPUT, 0) /* (R26) MMC1_DAT3 */
- J721E_IOPAD(0x258, PIN_INPUT, 0) /* (P23) MMC1_SDCD */
- J721E_IOPAD(0x25c, PIN_INPUT, 0) /* (R28) MMC1_SDWP */
- >;
- };
+&main_gpio2 {
+ status = "disabled";
+};
- vdd_sd_dv_alt_pins_default: vdd_sd_dv_alt_pins_default {
- pinctrl-single,pins = <
- J721E_IOPAD(0x1d8, PIN_OUTPUT, 7) /* (W4) SPI1_CS1.GPIO0_117 */
- >;
- };
+&main_gpio3 {
+ status = "disabled";
+};
+
+&main_gpio4 {
+ status = "disabled";
+};
+
+&main_gpio5 {
+ status = "disabled";
+};
+
+&main_gpio6 {
+ status = "disabled";
+};
+
+&main_gpio7 {
+ status = "disabled";
};
+&wkup_gpio1 {
+ status = "disabled";
+};
+
&main_sdhci0 {
/* eMMC */
non-removable;
ti,driver-strength-ohm = <50>;
+ disable-wp;
};
&main_sdhci1 {
- /* SD card */
+ /* SD/MMC */
+ vmmc-supply = <&vdd_mmc1>;
+ vqmmc-supply = <&vdd_sd_dv_alt>;
pinctrl-names = "default";
pinctrl-0 = <&main_mmc1_pins_default>;
ti,driver-strength-ohm = <50>;
- vmmc-supply = <&vdd_mmc1>;
- vqmmc-supply = <&vdd_sd_dv_alt>;
+ disable-wp;
};
-&main_pmx0 {
- main_usbss0_pins_default: main_usbss0_pins_default {
- pinctrl-single,pins = <
- J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
- J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
- >;
- };
+&main_sdhci2 {
+ /* Unused */
+ status = "disabled";
+};
- main_usbss1_pins_default: main_usbss1_pins_default {
- pinctrl-single,pins = <
- J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
- >;
- };
+&usb_serdes_mux {
+ idle-states = <1>, <0>; /* USB0 to SERDES3, USB1 to SERDES1 */
+};
- main_i2c0_pins_default: main-i2c0-pins-default {
- pinctrl-single,pins = <
- J721E_IOPAD(0x220, PIN_INPUT_PULLUP, 0) /* (AC5) I2C0_SCL */
- J721E_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (AA5) I2C0_SDA */
- >;
- };
+&serdes_ln_ctrl {
+ idle-states = <J721E_SERDES0_LANE0_PCIE0_LANE0>, <J721E_SERDES0_LANE1_PCIE0_LANE1>,
+ <J721E_SERDES1_LANE0_PCIE1_LANE0>, <J721E_SERDES1_LANE1_PCIE1_LANE1>,
+ <J721E_SERDES2_LANE0_PCIE2_LANE0>, <J721E_SERDES2_LANE1_PCIE2_LANE1>,
+ <J721E_SERDES3_LANE0_USB3_0_SWAP>, <J721E_SERDES3_LANE1_USB3_0>,
+ <J721E_SERDES4_LANE0_EDP_LANE0>, <J721E_SERDES4_LANE1_EDP_LANE1>,
+ <J721E_SERDES4_LANE2_EDP_LANE2>, <J721E_SERDES4_LANE3_EDP_LANE3>;
};
-&wkup_pmx0 {
- wkup_i2c0_pins_default: wkup-i2c0-pins-default {
- pinctrl-single,pins = <
- J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
- J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
- >;
- };
+&serdes_wiz3 {
+ typec-dir-gpios = <&main_gpio1 3 GPIO_ACTIVE_HIGH>;
+ typec-dir-debounce-ms = <700>; /* TUSB321, tCCB_DEFAULT 133 ms */
+};
- mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default {
- pinctrl-single,pins = <
- J721E_WKUP_IOPAD(0x34, PIN_OUTPUT, 0) /* (F22) MCU_OSPI1_CLK */
- J721E_WKUP_IOPAD(0x50, PIN_OUTPUT, 0) /* (C22) MCU_OSPI1_CSn0 */
- J721E_WKUP_IOPAD(0x40, PIN_INPUT, 0) /* (D22) MCU_OSPI1_D0 */
- J721E_WKUP_IOPAD(0x44, PIN_INPUT, 0) /* (G22) MCU_OSPI1_D1 */
- J721E_WKUP_IOPAD(0x48, PIN_INPUT, 0) /* (D23) MCU_OSPI1_D2 */
- J721E_WKUP_IOPAD(0x4c, PIN_INPUT, 0) /* (C23) MCU_OSPI1_D3 */
- J721E_WKUP_IOPAD(0x3c, PIN_INPUT, 0) /* (B23) MCU_OSPI1_DQS */
- J721E_WKUP_IOPAD(0x38, PIN_INPUT, 0) /* (A23) MCU_OSPI1_LBCLKO */
- >;
+&serdes3 {
+ serdes3_usb_link: link@0 {
+ reg = <0>;
+ cdns,num-lanes = <2>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_USB3>;
+ resets = <&serdes_wiz3 1>, <&serdes_wiz3 2>;
};
};
@@ -179,6 +376,8 @@
&usb0 {
dr_mode = "otg";
maximum-speed = "super-speed";
+ phys = <&serdes3_usb_link>;
+ phy-names = "cdns3,usb3-phy";
};
&usbss1 {
@@ -192,12 +391,38 @@
maximum-speed = "high-speed";
};
-&wkup_i2c0 {
+&ospi1 {
pinctrl-names = "default";
- pinctrl-0 = <&wkup_i2c0_pins_default>;
- clock-frequency = <400000>;
+ pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+
+ flash@0{
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-tx-bus-width = <1>;
+ spi-rx-bus-width = <4>;
+ spi-max-frequency = <40000000>;
+ cdns,tshsl-ns = <60>;
+ cdns,tsd2d-ns = <60>;
+ cdns,tchsh-ns = <60>;
+ cdns,tslch-ns = <60>;
+ cdns,read-delay = <2>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ };
};
+&tscadc0 {
+ adc {
+ ti,adc-channels = <0 1 2 3 4 5 6 7>;
+ };
+};
+
+&tscadc1 {
+ adc {
+ ti,adc-channels = <0 1 2 3 4 5 6 7>;
+ };
+};
+
&main_i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c0_pins_default>;
@@ -215,25 +440,281 @@
reg = <0x22>;
gpio-controller;
#gpio-cells = <2>;
+
+ p09-hog {
+ /* P11 - MCASP/TRACE_MUX_S0 */
+ gpio-hog;
+ gpios = <9 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "MCASP/TRACE_MUX_S0";
+ };
+
+ p10-hog {
+ /* P12 - MCASP/TRACE_MUX_S1 */
+ gpio-hog;
+ gpios = <10 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "MCASP/TRACE_MUX_S1";
+ };
};
};
-&ospi1 {
+&main_i2c1 {
pinctrl-names = "default";
- pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
+ pinctrl-0 = <&main_i2c1_pins_default>;
+ clock-frequency = <400000>;
- flash@0{
- compatible = "jedec,spi-nor";
- reg = <0x0>;
- spi-tx-bus-width = <1>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <40000000>;
- cdns,tshsl-ns = <60>;
- cdns,tsd2d-ns = <60>;
- cdns,tchsh-ns = <60>;
- cdns,tslch-ns = <60>;
- cdns,read-delay = <2>;
- #address-cells = <1>;
- #size-cells = <1>;
+ exp4: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c1_exp4_pins_default>;
+ interrupt-parent = <&main_gpio1>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+};
+
+&k3_clks {
+ /* Confiure AUDIO_EXT_REFCLK2 pin as output */
+ pinctrl-names = "default";
+ pinctrl-0 = <&audi_ext_refclk2_pins_default>;
+};
+
+&main_i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c3_pins_default>;
+ clock-frequency = <400000>;
+
+ exp3: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ pcm3168a_1: audio-codec@44 {
+ compatible = "ti,pcm3168a";
+ reg = <0x44>;
+
+ #sound-dai-cells = <1>;
+
+ reset-gpios = <&exp3 0 GPIO_ACTIVE_LOW>;
+
+ /* C_AUDIO_REFCLK2 -> RGMII6_RXC (W26) */
+ clocks = <&k3_clks 157 371>;
+ clock-names = "scki";
+
+ /* HSDIV3_16FFT_MAIN_4_HSDIVOUT2_CLK -> REFCLK2 */
+ assigned-clocks = <&k3_clks 157 371>;
+ assigned-clock-parents = <&k3_clks 157 400>;
+ assigned-clock-rates = <24576000>; /* for 48KHz */
+
+ VDD1-supply = <&vsys_3v3>;
+ VDD2-supply = <&vsys_3v3>;
+ VCCAD1-supply = <&vsys_5v0>;
+ VCCAD2-supply = <&vsys_5v0>;
+ VCCDA1-supply = <&vsys_5v0>;
+ VCCDA2-supply = <&vsys_5v0>;
+ };
+};
+
+&main_i2c6 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c6_pins_default>;
+ clock-frequency = <400000>;
+
+ exp5: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&mcu_cpsw {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+};
+
+&davinci_mdio {
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ };
+};
+
+&cpsw_port1 {
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&phy0>;
+};
+
+&dss {
+ /*
+ * These clock assignments are chosen to enable the following outputs:
+ *
+ * VP0 - DisplayPort SST
+ * VP1 - DPI0
+ * VP2 - DSI
+ * VP3 - DPI1
+ */
+
+ assigned-clocks = <&k3_clks 152 1>,
+ <&k3_clks 152 4>,
+ <&k3_clks 152 9>,
+ <&k3_clks 152 13>;
+ assigned-clock-parents = <&k3_clks 152 2>, /* PLL16_HSDIV0 */
+ <&k3_clks 152 6>, /* PLL19_HSDIV0 */
+ <&k3_clks 152 11>, /* PLL18_HSDIV0 */
+ <&k3_clks 152 18>; /* PLL23_HSDIV0 */
+};
+
+&mcasp0 {
+ status = "disabled";
+};
+
+&mcasp1 {
+ status = "disabled";
+};
+
+&mcasp2 {
+ status = "disabled";
+};
+
+&mcasp3 {
+ status = "disabled";
+};
+
+&mcasp4 {
+ status = "disabled";
+};
+
+&mcasp5 {
+ status = "disabled";
+};
+
+&mcasp6 {
+ status = "disabled";
+};
+
+&mcasp7 {
+ status = "disabled";
+};
+
+&mcasp8 {
+ status = "disabled";
+};
+
+&mcasp9 {
+ status = "disabled";
+};
+
+&mcasp10 {
+ #sound-dai-cells = <0>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcasp10_pins_default>;
+
+ op-mode = <0>; /* MCASP_IIS_MODE */
+ tdm-slots = <2>;
+ auxclk-fs-ratio = <256>;
+
+ serial-dir = < /* 0: INACTIVE, 1: TX, 2: RX */
+ 1 1 1 1
+ 2 2 2 0
+ >;
+ tx-num-evt = <0>;
+ rx-num-evt = <0>;
+};
+
+&mcasp11 {
+ status = "disabled";
+};
+
+&serdes0 {
+ serdes0_pcie_link: link@0 {
+ reg = <0>;
+ cdns,num-lanes = <1>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_PCIE>;
+ resets = <&serdes_wiz0 1>;
+ };
+};
+
+&serdes1 {
+ serdes1_pcie_link: link@0 {
+ reg = <0>;
+ cdns,num-lanes = <2>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_PCIE>;
+ resets = <&serdes_wiz1 1>, <&serdes_wiz1 2>;
};
};
+
+&serdes2 {
+ serdes2_pcie_link: link@0 {
+ reg = <0>;
+ cdns,num-lanes = <2>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_PCIE>;
+ resets = <&serdes_wiz2 1>, <&serdes_wiz2 2>;
+ };
+};
+
+&pcie0_rc {
+ reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
+ phys = <&serdes0_pcie_link>;
+ phy-names = "pcie-phy";
+ num-lanes = <1>;
+};
+
+&pcie1_rc {
+ reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>;
+ phys = <&serdes1_pcie_link>;
+ phy-names = "pcie-phy";
+ num-lanes = <2>;
+};
+
+&pcie2_rc {
+ reset-gpios = <&exp2 20 GPIO_ACTIVE_HIGH>;
+ phys = <&serdes2_pcie_link>;
+ phy-names = "pcie-phy";
+ num-lanes = <2>;
+};
+
+&pcie0_ep {
+ phys = <&serdes0_pcie_link>;
+ phy-names = "pcie-phy";
+ num-lanes = <1>;
+ status = "disabled";
+};
+
+&pcie1_ep {
+ phys = <&serdes1_pcie_link>;
+ phy-names = "pcie-phy";
+ num-lanes = <2>;
+ status = "disabled";
+};
+
+&pcie2_ep {
+ phys = <&serdes2_pcie_link>;
+ phy-names = "pcie-phy";
+ num-lanes = <2>;
+ status = "disabled";
+};
+
+&pcie3_rc {
+ status = "disabled";
+};
+
+&pcie3_ep {
+ status = "disabled";
+};
+
+&dss {
+ status = "disabled";
+};