arm: mvebu: Add Armada 38x DDR3 training code from Marvell bin_hdr
This patch adds the DDR3 setup and training code taken from the Marvell
U-Boot repository. This code used to be included as a binary (bin_hdr)
into the Armada A38x boot image. Not linked with the main U-Boot. With this
code addition and the serdes/PHY setup code, the Armada A38x support
in mainline U-Boot is finally self-contained. So the complete image
for booting can be built from mainline U-Boot. Without any additional
external inclusion.
Note:
This code has undergone many hours (days!) of coding-style cleanup and
refactoring. It still is not checkpatch clean though, I'm afraid. As the
factoring of the code has so many levels of indentation that many lines
are longer than 80 chars.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/drivers/ddr/marvell/a38x/ddr_topology_def.h b/drivers/ddr/marvell/a38x/ddr_topology_def.h
new file mode 100644
index 0000000..f8894e8
--- /dev/null
+++ b/drivers/ddr/marvell/a38x/ddr_topology_def.h
@@ -0,0 +1,112 @@
+/*
+ * Copyright (C) Marvell International Ltd. and its affiliates
+ *
+ * SPDX-License-Identifier: GPL-2.0
+ */
+
+#ifndef _DDR_TOPOLOGY_DEF_H
+#define _DDR_TOPOLOGY_DEF_H
+
+#include "ddr3_training_ip_def.h"
+#include "ddr3_topology_def.h"
+
+#if defined(CONFIG_ARMADA_38X)
+#include "ddr3_a38x.h"
+#endif
+
+/* bus width in bits */
+enum hws_bus_width {
+ BUS_WIDTH_4,
+ BUS_WIDTH_8,
+ BUS_WIDTH_16,
+ BUS_WIDTH_32
+};
+
+enum hws_temperature {
+ HWS_TEMP_LOW,
+ HWS_TEMP_NORMAL,
+ HWS_TEMP_HIGH
+};
+
+enum hws_mem_size {
+ MEM_512M,
+ MEM_1G,
+ MEM_2G,
+ MEM_4G,
+ MEM_8G,
+ MEM_SIZE_LAST
+};
+
+struct bus_params {
+ /* Chip Select (CS) bitmask (bits 0-CS0, bit 1- CS1 ...) */
+ u8 cs_bitmask;
+
+ /*
+ * mirror enable/disable
+ * (bits 0-CS0 mirroring, bit 1- CS1 mirroring ...)
+ */
+ int mirror_enable_bitmask;
+
+ /* DQS Swap (polarity) - true if enable */
+ int is_dqs_swap;
+
+ /* CK swap (polarity) - true if enable */
+ int is_ck_swap;
+};
+
+struct if_params {
+ /* bus configuration */
+ struct bus_params as_bus_params[MAX_BUS_NUM];
+
+ /* Speed Bin Table */
+ enum hws_speed_bin speed_bin_index;
+
+ /* bus width of memory */
+ enum hws_bus_width bus_width;
+
+ /* Bus memory size (MBit) */
+ enum hws_mem_size memory_size;
+
+ /* The DDR frequency for each interfaces */
+ enum hws_ddr_freq memory_freq;
+
+ /*
+ * delay CAS Write Latency
+ * - 0 for using default value (jedec suggested)
+ */
+ u8 cas_wl;
+
+ /*
+ * delay CAS Latency
+ * - 0 for using default value (jedec suggested)
+ */
+ u8 cas_l;
+
+ /* operation temperature */
+ enum hws_temperature interface_temp;
+};
+
+struct hws_topology_map {
+ /* Number of interfaces (default is 12) */
+ u8 if_act_mask;
+
+ /* Controller configuration per interface */
+ struct if_params interface_params[MAX_INTERFACE_NUM];
+
+ /* BUS per interface (default is 4) */
+ u8 num_of_bus_per_interface;
+
+ /* Bit mask for active buses */
+ u8 bus_act_mask;
+};
+
+/* DDR3 training global configuration parameters */
+struct tune_train_params {
+ u32 ck_delay;
+ u32 ck_delay_16;
+ u32 p_finger;
+ u32 n_finger;
+ u32 phy_reg3_val;
+};
+
+#endif /* _DDR_TOPOLOGY_DEF_H */