| /* |
| * Copyright (C) 2007 Sergey Kubushyn <ksi@koi8.net> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place, Suite 330, Boston, |
| * MA 02111-1307 USA |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| #include <asm/sizes.h> |
| |
| /* |
| * Define this to make U-Boot skip low level initialization when loaded |
| * by initial bootloader. Not required by NAND U-Boot version but IS |
| * required for a NOR version used to burn the real NOR U-Boot into |
| * NOR Flash. NAND and NOR support for DaVinci chips is mutually exclusive |
| * so it is NOT possible to build a U-Boot with both NAND and NOR routines. |
| * NOR U-Boot is loaded directly from Flash so it must perform all the |
| * low level initialization itself. NAND version is loaded by an initial |
| * bootloader (UBL in TI-ese) that performs such an initialization so it's |
| * skipped in NAND version. The third DaVinci boot mode loads a bootloader |
| * via UART0 and that bootloader in turn loads and runs U-Boot (or whatever) |
| * performing low level init prior to loading. All that means we can NOT use |
| * NAND version to put U-Boot into NOR because it doesn't have NOR support and |
| * we can NOT use NOR version because it performs low level initialization |
| * effectively destroying itself in DDR memory. That's why a separate NOR |
| * version with this define is needed. It is loaded via UART, then one uses |
| * it to somehow download a proper NOR version built WITHOUT this define to |
| * RAM (tftp?) and burn it to NOR Flash. I would be probably able to squeeze |
| * NOR support into the initial bootloader so it won't be needed but DaVinci |
| * static RAM might be too small for this (I have something like 2Kbytes left |
| * as of now, without NOR support) so this might've not happened... |
| * |
| #define CONFIG_NOR_UART_BOOT |
| */ |
| |
| /*=======*/ |
| /* Board */ |
| /*=======*/ |
| #define DV_EVM |
| #define CONFIG_SYS_NAND_SMALLPAGE |
| #define CONFIG_SYS_USE_NOR |
| /*===================*/ |
| /* SoC Configuration */ |
| /*===================*/ |
| #define CONFIG_ARM926EJS /* arm926ejs CPU core */ |
| #define CONFIG_SYS_TIMERBASE 0x01c21400 /* use timer 0 */ |
| #define CONFIG_SYS_HZ_CLOCK 27000000 /* Timer Input clock freq */ |
| #define CONFIG_SYS_HZ 1000 |
| #define CONFIG_SOC_DM644X |
| /*====================================================*/ |
| /* EEPROM definitions for Atmel 24C256BN SEEPROM chip */ |
| /* on Sonata/DV_EVM board. No EEPROM on schmoogie. */ |
| /*====================================================*/ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 20 |
| /*=============*/ |
| /* Memory Info */ |
| /*=============*/ |
| #define CONFIG_SYS_MALLOC_LEN (0x10000 + 128*1024) /* malloc() len */ |
| #define CONFIG_SYS_GBL_DATA_SIZE 128 /* reserved for initial data */ |
| #define CONFIG_SYS_MEMTEST_START 0x80000000 /* memtest start address */ |
| #define CONFIG_SYS_MEMTEST_END 0x81000000 /* 16MB RAM test */ |
| #define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ |
| #define CONFIG_STACKSIZE (256*1024) /* regular stack */ |
| #define PHYS_SDRAM_1 0x80000000 /* DDR Start */ |
| #define PHYS_SDRAM_1_SIZE 0x10000000 /* DDR size 256MB */ |
| #define DDR_8BANKS /* 8-bank DDR2 (256MB) */ |
| /*====================*/ |
| /* Serial Driver info */ |
| /*====================*/ |
| #define CONFIG_SYS_NS16550 |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE -4 /* NS16550 register size, byteorder */ |
| #define CONFIG_SYS_NS16550_COM1 0x01c20000 /* Base address of UART0 */ |
| #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_HZ_CLOCK /* Input clock to NS16550 */ |
| #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ |
| #define CONFIG_BAUDRATE 115200 /* Default baud rate */ |
| #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } |
| /*===================*/ |
| /* I2C Configuration */ |
| /*===================*/ |
| #define CONFIG_HARD_I2C |
| #define CONFIG_DRIVER_DAVINCI_I2C |
| #define CONFIG_SYS_I2C_SPEED 80000 /* 100Kbps won't work, silicon bug */ |
| #define CONFIG_SYS_I2C_SLAVE 10 /* Bogus, master-only in U-Boot */ |
| /*==================================*/ |
| /* Network & Ethernet Configuration */ |
| /*==================================*/ |
| #define CONFIG_DRIVER_TI_EMAC |
| #define CONFIG_MII |
| #define CONFIG_BOOTP_DEFAULT |
| #define CONFIG_BOOTP_DNS |
| #define CONFIG_BOOTP_DNS2 |
| #define CONFIG_BOOTP_SEND_HOSTNAME |
| #define CONFIG_NET_RETRY_COUNT 10 |
| /*=====================*/ |
| /* Flash & Environment */ |
| /*=====================*/ |
| #ifdef CONFIG_SYS_USE_NAND |
| #define CONFIG_NAND_DAVINCI |
| #undef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_SYS_NO_FLASH |
| #define CONFIG_ENV_IS_IN_NAND /* U-Boot env in NAND Flash */ |
| #ifdef CONFIG_SYS_NAND_SMALLPAGE |
| #define CONFIG_ENV_SECT_SIZE 512 /* Env sector Size */ |
| #define CONFIG_ENV_SIZE SZ_16K |
| #else |
| #define CONFIG_ENV_SECT_SIZE 2048 /* Env sector Size */ |
| #define CONFIG_ENV_SIZE SZ_128K |
| #endif |
| #define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ |
| #define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ |
| #define CONFIG_SYS_NAND_BASE 0x02000000 |
| #define CONFIG_SYS_NAND_HW_ECC |
| #define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */ |
| #define CONFIG_ENV_OFFSET 0x0 /* Block 0--not used by bootcode */ |
| #define DEF_BOOTM "" |
| #elif defined(CONFIG_SYS_USE_NOR) |
| #ifdef CONFIG_NOR_UART_BOOT |
| #define CONFIG_SKIP_LOWLEVEL_INIT /* U-Boot is loaded by a bootloader */ |
| #define CONFIG_SKIP_RELOCATE_UBOOT /* to a proper address, init done */ |
| #else |
| #undef CONFIG_SKIP_LOWLEVEL_INIT |
| #undef CONFIG_SKIP_RELOCATE_UBOOT |
| #endif |
| #define CONFIG_ENV_IS_IN_FLASH |
| #undef CONFIG_SYS_NO_FLASH |
| #define CONFIG_FLASH_CFI_DRIVER |
| #define CONFIG_SYS_FLASH_CFI |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of flash banks */ |
| #define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* 64KB sect size AMD Flash */ |
| #define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SECT_SZ*3) |
| #define PHYS_FLASH_1 0x02000000 /* CS2 Base address */ |
| #define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 /* Flash Base for U-Boot */ |
| #define PHYS_FLASH_SIZE 0x2000000 /* Flash size 32MB */ |
| #define CONFIG_SYS_MAX_FLASH_SECT (PHYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ) |
| #define CONFIG_ENV_SECT_SIZE CONFIG_SYS_FLASH_SECT_SZ /* Env sector Size */ |
| #endif |
| /*==============================*/ |
| /* U-Boot general configuration */ |
| /*==============================*/ |
| #undef CONFIG_USE_IRQ /* No IRQ/FIQ in U-Boot */ |
| #define CONFIG_MISC_INIT_R |
| #undef CONFIG_BOOTDELAY |
| #define CONFIG_BOOTFILE "uImage" /* Boot file name */ |
| #define CONFIG_SYS_PROMPT "U-Boot > " /* Monitor Command Prompt */ |
| #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print buffer sz */ |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| #define CONFIG_SYS_LOAD_ADDR 0x80700000 /* default Linux kernel load address */ |
| #define CONFIG_VERSION_VARIABLE |
| #define CONFIG_AUTO_COMPLETE /* Won't work with hush so far, may be later */ |
| #define CONFIG_SYS_HUSH_PARSER |
| #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " |
| #define CONFIG_CMDLINE_EDITING |
| #define CONFIG_SYS_LONGHELP |
| #define CONFIG_CRC32_VERIFY |
| #define CONFIG_MX_CYCLIC |
| #define CONFIG_MUSB_HCD |
| #define CONFIG_USB_DAVINCI |
| /*===================*/ |
| /* Linux Information */ |
| /*===================*/ |
| #define LINUX_BOOT_PARAM_ADDR 0x80000100 |
| #define CONFIG_CMDLINE_TAG |
| #define CONFIG_SETUP_MEMORY_TAGS |
| #define CONFIG_BOOTARGS "mem=120M console=ttyS0,115200n8 root=/dev/hda1 rw noinitrd ip=dhcp" |
| #define CONFIG_BOOTCOMMAND "setenv setboot setenv bootargs \\$(bootargs) video=dm64xxfb:output=\\$(videostd);run setboot; bootm 0x2050000" |
| /*=================*/ |
| /* U-Boot commands */ |
| /*=================*/ |
| #include <config_cmd_default.h> |
| #define CONFIG_CMD_ASKENV |
| #define CONFIG_CMD_DHCP |
| #define CONFIG_CMD_DIAG |
| #define CONFIG_CMD_I2C |
| #define CONFIG_CMD_MII |
| #define CONFIG_CMD_PING |
| #define CONFIG_CMD_SAVES |
| #define CONFIG_CMD_EEPROM |
| #undef CONFIG_CMD_BDI |
| #undef CONFIG_CMD_FPGA |
| #undef CONFIG_CMD_SETGETDCR |
| #ifdef CONFIG_SYS_USE_NAND |
| #undef CONFIG_CMD_FLASH |
| #undef CONFIG_CMD_IMLS |
| #define CONFIG_CMD_NAND |
| #elif defined(CONFIG_SYS_USE_NOR) |
| #define CONFIG_CMD_JFFS2 |
| #else |
| #error "Either CONFIG_SYS_USE_NAND or CONFIG_SYS_USE_NOR _MUST_ be defined !!!" |
| #endif |
| /*==========================*/ |
| /* USB MSC support (if any) */ |
| /*==========================*/ |
| #ifdef CONFIG_USB_DAVINCI |
| #define CONFIG_CMD_USB |
| #ifdef CONFIG_MUSB_HCD |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_CMD_STORAGE |
| #define CONFIG_CMD_FAT |
| #define CONFIG_DOS_PARTITION |
| #endif |
| #ifdef CONFIG_USB_KEYBOARD |
| #define CONFIG_SYS_USB_EVENT_POLL |
| #define CONFIG_PREBOOT "usb start" |
| #endif |
| #endif |
| /*=======================*/ |
| /* KGDB support (if any) */ |
| /*=======================*/ |
| #ifdef CONFIG_CMD_KGDB |
| #define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ |
| #define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */ |
| #endif |
| #endif /* __CONFIG_H */ |