diff --git a/board/variscite/dart_6ul/Kconfig b/board/variscite/dart_6ul/Kconfig
new file mode 100644
index 0000000..1765af1
--- /dev/null
+++ b/board/variscite/dart_6ul/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_DART_6UL
+
+config SYS_BOARD
+	default "dart_6ul"
+
+config SYS_VENDOR
+	default "variscite"
+
+config SYS_CONFIG_NAME
+	default "dart_6ul"
+
+endif
diff --git a/board/variscite/dart_6ul/MAINTAINERS b/board/variscite/dart_6ul/MAINTAINERS
new file mode 100644
index 0000000..339f93f
--- /dev/null
+++ b/board/variscite/dart_6ul/MAINTAINERS
@@ -0,0 +1,8 @@
+MX6UL_DART BOARD
+M:	Parthiban Nallathambi <parthitce@gmail.com>
+S:	Maintained
+F:	arch/arm/dts/imx6ull-dart-6ul.dts
+F:	arch/arm/dts/imx6ull-dart-6ul.dtsi
+F:	board/variscite/dart_6ul/
+F:	configs/variscite_dart6ul_defconfig
+F:	include/configs/dart_6ul.h
diff --git a/board/variscite/dart_6ul/Makefile b/board/variscite/dart_6ul/Makefile
new file mode 100644
index 0000000..48aa361
--- /dev/null
+++ b/board/variscite/dart_6ul/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier:	GPL-2.0+
+
+obj-y  := dart_6ul.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/variscite/dart_6ul/README b/board/variscite/dart_6ul/README
new file mode 100644
index 0000000..d76b997
--- /dev/null
+++ b/board/variscite/dart_6ul/README
@@ -0,0 +1,41 @@
+How to use U-Boot on variscite DART-6UL Evaluation Kit
+------------------------------------------------------
+
+- Configure and build U-Boot for DART-6UL iMX6ULL:
+
+    $ make mrproper
+    $ make variscite_dart6ul_defconfig
+    $ make
+
+  This will generate SPL and u-boot-dtb.img images.
+
+Boot from MMC/SD:
+- The SPL and u-boot-dtb.img images need to be flashed into the micro SD card:
+
+    $ sudo dd if=SPL of=/dev/mmcblk0 bs=1k seek=1; sync
+    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk0 bs=1k seek=69; sync
+
+- Boot mode settings:
+
+  Boot switch position: SW1 -> 0
+			SW2 -> 0
+
+Boot from eMMC:
+- if bootpart is not enabled by default, to enable under Linux
+	echo 0 >/sys/block/mmcblk1boot0/force_ro
+	mmc bootpart enable 1 1 /dev/mmcblk1boot0
+
+- Flash the SPL and u-boot-dtb.img to mmcblk1boot0
+    $ sudo dd if=SPL of=/dev/mmcblk1boot0 bs=1k seek=1; sync
+    $ sudo dd if=u-boot-dtb.img of=/dev/mmcblk1boot0 bs=1k seek=69; sync
+
+- Boot mode settings:
+
+  Boot switch position: SW1 -> 0
+			SW2 -> 1
+
+- Connect the Serial cable to UART0 and the PC for the console.
+
+- Insert the micro SD card in the board and power it up.
+
+- U-Boot messages should come up.
diff --git a/board/variscite/dart_6ul/dart_6ul.c b/board/variscite/dart_6ul/dart_6ul.c
new file mode 100644
index 0000000..4765595
--- /dev/null
+++ b/board/variscite/dart_6ul/dart_6ul.c
@@ -0,0 +1,228 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2019 Variscite Ltd.
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/mach-imx/iomux-v3.h>
+#include <asm/mach-imx/mxc_i2c.h>
+#include <fsl_esdhc.h>
+#include <linux/bitops.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <usb.h>
+#include <usb/ehci-ci.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
+
+#ifdef CONFIG_NAND_MXS
+#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
+#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
+			PAD_CTL_SRE_FAST)
+#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)
+static iomux_v3_cfg_t const nand_pads[] = {
+	MX6_PAD_NAND_DATA00__RAWNAND_DATA00 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA01__RAWNAND_DATA01 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA02__RAWNAND_DATA02 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA03__RAWNAND_DATA03 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA04__RAWNAND_DATA04 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA05__RAWNAND_DATA05 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA06__RAWNAND_DATA06 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DATA07__RAWNAND_DATA07 | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_CLE__RAWNAND_CLE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_ALE__RAWNAND_ALE | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_CE0_B__RAWNAND_CE0_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_RE_B__RAWNAND_RE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_WE_B__RAWNAND_WE_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_WP_B__RAWNAND_WP_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_READY_B__RAWNAND_READY_B | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+	MX6_PAD_NAND_DQS__RAWNAND_DQS | MUX_PAD_CTRL(GPMI_PAD_CTRL2),
+};
+
+static void setup_gpmi_nand(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	/* config gpmi nand iomux */
+	imx_iomux_v3_setup_multiple_pads(nand_pads, ARRAY_SIZE(nand_pads));
+
+	clrbits_le32(&mxc_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+	/*
+	 * config gpmi and bch clock to 100 MHz
+	 * bch/gpmi select PLL2 PFD2 400M
+	 * 100M = 400M / 4
+	 */
+	clrbits_le32(&mxc_ccm->cscmr1,
+		     MXC_CCM_CSCMR1_BCH_CLK_SEL |
+		     MXC_CCM_CSCMR1_GPMI_CLK_SEL);
+	clrsetbits_le32(&mxc_ccm->cscdr1,
+			MXC_CCM_CSCDR1_BCH_PODF_MASK |
+			MXC_CCM_CSCDR1_GPMI_PODF_MASK,
+			(3 << MXC_CCM_CSCDR1_BCH_PODF_OFFSET) |
+			(3 << MXC_CCM_CSCDR1_GPMI_PODF_OFFSET));
+
+	/* enable gpmi and bch clock gating */
+	setbits_le32(&mxc_ccm->CCGR4,
+		     MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
+		     MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
+		     MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_MASK);
+
+	/* enable apbh clock gating */
+	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
+}
+#endif
+
+#ifdef CONFIG_FEC_MXC
+#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
+#define ENET_PAD_CTRL     (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE       | \
+			   PAD_CTL_SPEED_HIGH  | PAD_CTL_DSE_48ohm | \
+			   PAD_CTL_SRE_FAST)
+#define MDIO_PAD_CTRL     (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE      | \
+			   PAD_CTL_DSE_48ohm   | PAD_CTL_SRE_FAST | \
+			   PAD_CTL_ODE)
+/*
+ * pin conflicts for fec1 and fec2, GPIO1_IO06 and GPIO1_IO07 can only
+ * be used for ENET1 or ENET2, cannot be used for both.
+ */
+static iomux_v3_cfg_t const fec1_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET1_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA0__ENET1_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_DATA1__ENET1_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_EN__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA0__ENET1_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_DATA1__ENET1_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_ER__ENET1_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET1_RX_EN__ENET1_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const fec2_pads[] = {
+	MX6_PAD_GPIO1_IO06__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
+	MX6_PAD_GPIO1_IO07__ENET2_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_EN__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_ER__ENET2_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET2_RX_EN__ENET2_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
+};
+
+static void setup_iomux_fec(int fec_id)
+{
+	if (fec_id == 0)
+		imx_iomux_v3_setup_multiple_pads(fec1_pads,
+						 ARRAY_SIZE(fec1_pads));
+	else
+		imx_iomux_v3_setup_multiple_pads(fec2_pads,
+						 ARRAY_SIZE(fec2_pads));
+}
+
+int board_eth_init(bd_t *bis)
+{
+	int ret = 0;
+
+	ret = fecmxc_initialize_multi(bis, CONFIG_FEC_ENET_DEV,
+				      CONFIG_FEC_MXC_PHYADDR, IMX_FEC_BASE);
+
+#if defined(CONFIG_CI_UDC) && defined(CONFIG_USB_ETHER)
+	/* USB Ethernet Gadget */
+	usb_eth_initialize(bis);
+#endif
+	return ret;
+}
+
+static int setup_fec(int fec_id)
+{
+	struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int ret;
+
+	if (fec_id == 0) {
+		/*
+		 * Use 50M anatop loopback REF_CLK1 for ENET1,
+		 * clear gpr1[13], set gpr1[17].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC1_MASK,
+				IOMUX_GPR1_FEC1_CLOCK_MUX1_SEL_MASK);
+	} else {
+		/*
+		 * Use 50M anatop loopback REF_CLK2 for ENET2,
+		 * clear gpr1[14], set gpr1[18].
+		 */
+		clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
+				IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
+	}
+
+	ret = enable_fec_anatop_clock(fec_id, ENET_50MHZ);
+	if (ret)
+		return ret;
+
+	enable_enet_clk(1);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	/*
+	 * Defaults + Enable status LEDs (LED1: Activity, LED0: Link) & select
+	 * 50 MHz RMII clock mode.
+	 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+#endif /* CONFIG_FEC_MXC */
+
+int board_early_init_f(void)
+{
+	setup_iomux_fec(CONFIG_FEC_ENET_DEV);
+
+	return 0;
+}
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_FEC_MXC
+	setup_fec(CONFIG_FEC_ENET_DEV);
+#endif
+
+#ifdef CONFIG_NAND_MXS
+	setup_gpmi_nand();
+#endif
+	return 0;
+}
+
+int checkboard(void)
+{
+	puts("Board: Variscite DART-6UL Evaluation Kit\n");
+
+	return 0;
+}
diff --git a/board/variscite/dart_6ul/spl.c b/board/variscite/dart_6ul/spl.c
new file mode 100644
index 0000000..f7e6ab6
--- /dev/null
+++ b/board/variscite/dart_6ul/spl.c
@@ -0,0 +1,215 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2015-2019 Variscite Ltd.
+ * Copyright (C) 2019 Parthiban Nallathambi <parthitce@gmail.com>
+ */
+
+#include <common.h>
+#include <spl.h>
+#include <asm/arch/clock.h>
+#include <asm/io.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/crm_regs.h>
+#include <fsl_esdhc.h>
+
+#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
+	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart1_pads[] = {
+	MX6_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
+}
+
+static struct mx6ul_iomux_grp_regs mx6_grp_ioregs = {
+	.grp_addds = 0x00000030,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_b0ds = 0x00000030,
+	.grp_ctlds = 0x00000030,
+	.grp_b1ds = 0x00000030,
+	.grp_ddrpke = 0x00000000,
+	.grp_ddrmode = 0x00020000,
+	.grp_ddr_type = 0x000c0000,
+};
+
+static struct mx6ul_iomux_ddr_regs mx6_ddr_ioregs = {
+	.dram_dqm0 = 0x00000030,
+	.dram_dqm1 = 0x00000030,
+	.dram_ras = 0x00000030,
+	.dram_cas = 0x00000030,
+	.dram_odt0 = 0x00000030,
+	.dram_odt1 = 0x00000030,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdclk_0 = 0x00000008,
+	.dram_sdqs0 = 0x00000038,
+	.dram_sdqs1 = 0x00000030,
+	.dram_reset = 0x00000030,
+};
+
+static struct mx6_mmdc_calibration mx6_mmcd_calib = {
+	.p0_mpwldectrl0 = 0x00000000,
+	.p0_mpdgctrl0   = 0x414C0158,
+	.p0_mprddlctl   = 0x40403A3A,
+	.p0_mpwrdlctl   = 0x40405A56,
+};
+
+struct mx6_ddr_sysinfo ddr_sysinfo = {
+	.dsize = 0,
+	.cs_density = 20,
+	.ncs = 1,
+	.cs1_mirror = 0,
+	.rtt_wr = 2,
+	.rtt_nom = 1,		/* RTT_Nom = RZQ/2 */
+	.walat = 1,		/* Write additional latency */
+	.ralat = 5,		/* Read additional latency */
+	.mif3_mode = 3,		/* Command prediction working mode */
+	.bi_on = 1,		/* Bank interleaving enabled */
+	.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
+	.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
+};
+
+static struct mx6_ddr3_cfg mem_ddr = {
+	.mem_speed = 800,
+	.density = 4,
+	.width = 16,
+	.banks = 8,
+	.rowaddr = 15,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+};
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0xFFFFFFFF, &ccm->CCGR0);
+	writel(0xFFFFFFFF, &ccm->CCGR1);
+	writel(0xFFFFFFFF, &ccm->CCGR2);
+	writel(0xFFFFFFFF, &ccm->CCGR3);
+	writel(0xFFFFFFFF, &ccm->CCGR4);
+	writel(0xFFFFFFFF, &ccm->CCGR5);
+	writel(0xFFFFFFFF, &ccm->CCGR6);
+	writel(0xFFFFFFFF, &ccm->CCGR7);
+	/* Enable Audio Clock for SOM codec */
+	writel(0x01130100, (long *)CCM_CCOSR);
+}
+
+static void spl_dram_init(void)
+{
+	mx6ul_dram_iocfg(mem_ddr.width, &mx6_ddr_ioregs, &mx6_grp_ioregs);
+	mx6_dram_cfg(&ddr_sysinfo, &mx6_mmcd_calib, &mem_ddr);
+}
+
+#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
+	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
+	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+static iomux_v3_cfg_t const usdhc1_pads[] = {
+	MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+#ifndef CONFIG_NAND_MXS
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_NAND_RE_B__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_WE_B__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA00__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA01__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA02__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA03__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA04__USDHC2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA05__USDHC2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA06__USDHC2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NAND_DATA07__USDHC2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+#endif
+
+static struct fsl_esdhc_cfg usdhc_cfg[] = {
+	{
+		.esdhc_base = USDHC1_BASE_ADDR,
+		.max_bus_width = 4,
+	},
+#ifndef CONFIG_NAND_MXS
+	{
+		.esdhc_base = USDHC2_BASE_ADDR,
+		.max_bus_width = 8,
+	},
+#endif
+};
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	return 1;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int i, ret;
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			SETUP_IOMUX_PADS(usdhc1_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
+			break;
+#ifndef CONFIG_NAND_MXS
+		case 1:
+			SETUP_IOMUX_PADS(usdhc2_pads);
+			usdhc_cfg[i].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+#endif
+		default:
+			printf("Warning - USDHC%d controller not supporting\n",
+			       i + 1);
+			return 0;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret) {
+			printf("Warning: failed to initialize mmc dev %d\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+void board_init_f(ulong dummy)
+{
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	ccgr_init();
+
+	/* setup GP timer */
+	timer_init();
+
+	setup_iomux_uart();
+
+	/* iomux and setup of i2c */
+	board_early_init_f();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+
+	/* Clear the BSS. */
+	memset(__bss_start, 0, __bss_end - __bss_start);
+
+	/* load/boot image from boot device */
+	board_init_r(NULL, 0);
+}