Initial revision
diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h
new file mode 100644
index 0000000..29e4807
--- /dev/null
+++ b/include/configs/GEN860T.h
@@ -0,0 +1,717 @@
+/*
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ * Keith Outwater, keith_outwater@mvis.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config_GEN860T.h - board specific configuration options
+ */
+
+#ifndef __CONFIG_GEN860T_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC860
+#define CONFIG_GEN860T
+
+/*
+ * Identify the board
+ */
+#define CONFIG_IDENT_STRING " GEN860T"
+
+/*
+ * Don't depend on the RTC clock to determine clock frequency -
+ * the 860's internal rtc uses a 32.768 KHz clock which is
+ * generated by the DS1337 - and the DS1337 clock can be turned off.
+ */
+#define CONFIG_8xx_GCLK_FREQ 66600000
+
+/*
+ * The RS-232 console port is on SMC1
+ */
+#define CONFIG_8xx_CONS_SMC1
+#define CONFIG_BAUDRATE 38400
+
+/*
+ * Set allowable console baud rates
+ */
+#define CFG_BAUDRATE_TABLE { 9600, \
+ 19200, \
+ 38400, \
+ 57600, \
+ 115200, \
+ }
+
+/*
+ * Print console information
+ */
+#undef CFG_CONSOLE_INFO_QUIET
+
+/*
+ * Set the autoboot delay in seconds. A delay of -1 disables autoboot
+ */
+#define CONFIG_BOOTDELAY 5
+
+/*
+ * Pass the clock frequency to the Linux kernel in units of MHz
+ */
+#define CONFIG_CLOCKS_IN_MHZ
+
+#define CONFIG_PREBOOT \
+ "echo;echo"
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp;" \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+/*
+ * Turn off echo for serial download by default. Allow baud rate to be changed
+ * for downloads
+ */
+#undef CONFIG_LOADS_ECHO
+#define CFG_LOADS_BAUD_CHANGE
+
+/*
+ * Set default load address for tftp network downloads
+ */
+#define CFG_TFTP_LOADADDR 0x01000000
+
+/*
+ * Turn off the watchdog timer
+ */
+#undef CONFIG_WATCHDOG
+
+/*
+ * Do not reboot if a panic occurs
+ */
+#define CONFIG_PANIC_HANG
+
+/*
+ * Enable the status LED
+ */
+#define CONFIG_STATUS_LED
+
+/*
+ * Reset address. We pick an address such that when an instruction
+ * is executed at that address, a machine check exception occurs
+ */
+#define CFG_RESET_ADDRESS ((ulong) -1)
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_MASK ( CONFIG_BOOTP_DEFAULT | \
+ CONFIG_BOOTP_BOOTFILESIZE \
+ )
+
+/*
+ * The GEN860T network interface uses the on-chip 10/100 FEC with
+ * an Intel LXT971A PHY connected to the 860T's MII. The PHY's
+ * MII address is hardwired on the board to zero.
+ */
+#define CONFIG_FEC_ENET
+#define CFG_DISCOVER_PHY
+#define CONFIG_MII
+#define CONFIG_PHY_ADDR 0
+
+/*
+ * Set default IP stuff just to get bootstrap entries into the
+ * environment so that we can autoscript the full default environment.
+ */
+#define CONFIG_ETHADDR 9a:52:63:15:85:25
+#define CONFIG_SERVERIP 10.0.4.200
+#define CONFIG_IPADDR 10.0.4.111
+
+/*
+ * This board has a 32 kibibyte EEPROM (Atmel AT24C256) connected to
+ * the MPC860T I2C interface.
+ */
+#define CFG_I2C_EEPROM_ADDR 0x50
+#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 12 /* 10 mS w/ 20% margin */
+#define CFG_I2C_EEPROM_ADDR_LEN 2 /* need 16 bit address */
+#define CFG_ENV_EEPROM_SIZE (32 * 1024)
+
+#undef CONFIG_HARD_I2C
+#define CONFIG_SOFT_I2C
+
+/*
+ * Configure software I2C support (taken from IP860 BSP).
+ * The I2C bus is connected to the GEN860T's 'dedicated' I2C
+ * pins, i.e. PB26 and PB27
+ */
+#define PB_SCL 0x00000020 /* PB 26 */
+#define PB_SDA 0x00000010 /* PB 27 */
+
+#define I2C_INIT (immr->im_cpm.cp_pbdir |= PB_SCL)
+#define I2C_ACTIVE (immr->im_cpm.cp_pbdir |= PB_SDA)
+#define I2C_TRISTATE (immr->im_cpm.cp_pbdir &= ~PB_SDA)
+#define I2C_READ ((immr->im_cpm.cp_pbdat & PB_SDA) != 0)
+#define I2C_SDA(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SDA; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SDA
+#define I2C_SCL(bit) if(bit) immr->im_cpm.cp_pbdat |= PB_SCL; \
+ else immr->im_cpm.cp_pbdat &= ~PB_SCL
+#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
+
+#define CFG_I2C_SPEED 100000 /* clock speed in Hz */
+#define CFG_I2C_SLAVE 0xFE /* I2C slave address */
+
+/*
+ * Allow environment overwrites by anyone
+ */
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * The MPC860's internal RTC is horribly broken in rev D masks. Three
+ * internal MPC860T circuit nodes were inadvertently left floating; this
+ * causes KAPWR current in power down mode to be three orders of magnitude
+ * higher than specified in the datasheet (from 10 uA to 10 mA). No
+ * reasonable battery can keep that kind RTC running during powerdown for any
+ * length of time, so we use an external RTC on the I2C bus instead.
+ */
+#undef CONFIG_RTC_MPC8xx
+#define CONFIG_RTC_DS1337
+#define CFG_I2C_RTC_ADDR 0x68
+
+/*
+ * Allow partial commands to be matched to uniqueness.
+ */
+#define CFG_MATCH_PARTIAL_CMD
+
+/*
+ * List of available monitor commands. Use the system default list
+ * plus add some of the "non-standard" commands back in.
+ * See ./cmd_confdefs.h
+ */
+#define CONFIG_COMMANDS ( CONFIG_CMD_DFL | \
+ CFG_CMD_ASKENV | \
+ CFG_CMD_DHCP | \
+ CFG_CMD_I2C | \
+ CFG_CMD_DOC | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_REGINFO | \
+ CFG_CMD_IMMAP | \
+ CFG_CMD_ELF | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DATE | \
+ CFG_CMD_FPGA | \
+ CFG_CMD_MII | \
+ CFG_CMD_BEDBUG \
+ )
+
+/*
+ * There is no IDE/PCMCIA hardware support on the board.
+ */
+#undef CONFIG_IDE_PCMCIA
+#undef CONFIG_IDE_LED
+#undef CONFIG_IDE_RESET
+
+/*
+ * Enable the call to misc_init_r() for miscellaneous platform
+ * dependent initialization.
+ */
+#define CONFIG_MISC_INIT_R
+
+/*
+ * Enable call to last_stage_init() so we can twiddle some LEDS :)
+ */
+#define CONFIG_LAST_STAGE_INIT
+
+/*
+ * Virtex2 FPGA configuration support
+ */
+#define CONFIG_FPGA_COUNT 1
+#define CONFIG_FPGA CFG_XILINX_VIRTEX2
+#define CFG_FPGA_PROG_FEEDBACK
+
+
+/************************************************************************
+ * This must be included AFTER the definition of any CONFIG_COMMANDS
+ */
+#include <cmd_confdefs.h>
+
+/*
+ * Verbose help from command monitor.
+ */
+#define CFG_LONGHELP
+#define CFG_PROMPT "gen860t> "
+
+/*
+ * Use the "hush" command parser
+ */
+#define CFG_HUSH_PARSER
+#define CFG_PROMPT_HUSH_PS2 "> "
+
+/*
+ * Set buffer size for console I/O
+ */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024
+#else
+#define CFG_CBSIZE 256
+#endif
+
+/*
+ * Print buffer size
+ */
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)
+
+/*
+ * Maximum number of arguments that a command can accept
+ */
+#define CFG_MAXARGS 16
+
+/*
+ * Boot argument buffer size
+ */
+#define CFG_BARGSIZE CFG_CBSIZE
+
+/*
+ * Default memory test range
+ */
+#define CFG_MEMTEST_START 0x0100000
+#define CFG_MEMTEST_END (CFG_MEMTEST_START + (128 * 1024))
+
+/*
+ * Select the more full-featured memory test
+ */
+#define CFG_ALT_MEMTEST
+
+/*
+ * Default load address
+ */
+#define CFG_LOAD_ADDR 0x01000000
+
+/*
+ * Set decrementer frequency (1 ms ticks)
+ */
+#define CFG_HZ 1000
+
+/*
+ * Device memory map (after SDRAM remap to 0x0):
+ *
+ * CS Device Base Addr Size
+ * ----------------------------------------------------
+ * CS0* Flash 0x40000000 64 M
+ * CS1* SDRAM 0x00000000 16 M
+ * CS2* Disk-On-Chip 0x50000000 32 K
+ * CS3* FPGA 0x60000000 64 M
+ * CS4* SelectMap 0x70000000 32 K
+ * CS5* Mil-Std 1553 I/F 0x80000000 32 K
+ * CS6* Unused
+ * CS7* Unused
+ * IMMR 860T Registers 0xfff00000
+ */
+
+/*
+ * Base addresses and block sizes
+ */
+#define CFG_IMMR 0xFF000000
+
+#define SDRAM_BASE 0x00000000
+#define SDRAM_SIZE (64 * 1024 * 1024)
+
+#define FLASH_BASE 0x40000000
+#define FLASH_SIZE (16 * 1024 * 1024)
+
+#define DOC_BASE 0x50000000
+#define DOC_SIZE (32 * 1024)
+
+#define FPGA_BASE 0x60000000
+#define FPGA_SIZE (64 * 1024 * 1024)
+
+#define SELECTMAP_BASE 0x70000000
+#define SELECTMAP_SIZE (32 * 1024)
+
+#define M1553_BASE 0x80000000
+#define M1553_SIZE (64 * 1024)
+
+/*
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_INIT_DATA_SIZE 64 /* # bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_INIT_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE SDRAM_BASE
+
+/*
+ * FLASH organization
+ */
+#define CFG_FLASH_BASE FLASH_BASE
+#define CFG_FLASH_SIZE FLASH_SIZE
+#define CFG_FLASH_SECT_SIZE (128 * 1024)
+#define CFG_MAX_FLASH_BANKS 1
+#define CFG_MAX_FLASH_SECT 128
+
+/*
+ * The timeout values are for an entire chip and are in milliseconds.
+ * Yes I know that the write timeout is huge. Accroding to the
+ * datasheet a single byte takes 630 uS (round to 1 ms) max at worst
+ * case VCC and temp after 100K programming cycles. It works out
+ * to 280 minutes (might as well be forever).
+ */
+#define CFG_FLASH_ERASE_TOUT (CFG_MAX_FLASH_SECT * 5000)
+#define CFG_FLASH_WRITE_TOUT (CFG_MAX_FLASH_SECT * 128 * 1024 * 1)
+
+/*
+ * Allow direct writes to FLASH from tftp transfers (** dangerous **)
+ */
+#define CFG_DIRECT_FLASH_TFTP
+
+/*
+ * Reserve memory for U-Boot.
+ */
+#define CFG_MAX_U_BOOT_SECT 3
+
+#if defined(DEBUG)
+#define CFG_MONITOR_LEN (512 * 1024)
+#else
+#define CFG_MONITOR_LEN (256 * 1024)
+#endif
+
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+
+/*
+ * Select environment placement. NOTE that u-boot.lds must
+ * be edited if this is changed!
+ */
+#undef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_IS_IN_EEPROM
+
+#if defined(CFG_ENV_IS_IN_EEPROM)
+#define CFG_ENV_SIZE (2 * 1024)
+#define CFG_ENV_OFFSET (CFG_ENV_EEPROM_SIZE - (8 * 1024))
+#else
+#define CFG_ENV_SIZE (4 * 1024)
+#define CFG_ENV_OFFSET (CFG_MAX_U_BOOT_SECT * CFG_FLASH_SECT_SIZE)
+#endif
+
+/*
+ * Reserve memory for malloc()
+ */
+#define CFG_MALLOC_LEN (128 * 1024)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 * 1024 * 1024)
+
+/*
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of above value */
+#endif
+
+/*------------------------------------------------------------------------
+ * SYPCR - System Protection Control UM 11-9
+ * -----------------------------------------------------------------------
+ * SYPCR can only be written once after reset!
+ *
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR ( SYPCR_SWTC | \
+ SYPCR_BMT | \
+ SYPCR_BME | \
+ SYPCR_SWF | \
+ SYPCR_SWE | \
+ SYPCR_SWRI | \
+ SYPCR_SWP \
+ )
+#else
+#define CFG_SYPCR ( SYPCR_SWTC | \
+ SYPCR_BMT | \
+ SYPCR_BME | \
+ SYPCR_SWF | \
+ SYPCR_SWP \
+ )
+#endif
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration UM 11-6
+ *-----------------------------------------------------------------------
+ * Set debug pin mux, enable SPKROUT and GPLB5*.
+ */
+#define CFG_SIUMCR ( SIUMCR_DBGC11 | \
+ SIUMCR_DBPC11 | \
+ SIUMCR_MLRC11 | \
+ SIUMCR_GB5E \
+ )
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control UM 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freeze enabled
+ */
+#define CFG_TBSCR ( TBSCR_REFA | \
+ TBSCR_REFB | \
+ TBSCR_TBF \
+ )
+
+/*-----------------------------------------------------------------------
+ * RTCSC - Real-Time Clock Status and Control Register UM 11-27
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RTCSC ( RTCSC_SEC | \
+ RTCSC_ALR | \
+ RTCSC_RTF | \
+ RTCSC_RTE \
+ )
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control UM 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR ( PISCR_PS | \
+ PISCR_PITF \
+ )
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register UM 15-30
+ *-----------------------------------------------------------------------
+ * Reset PLL lock status sticky bit, timer expired status bit and timer
+ * interrupt status bit. Set MF for 1:2:1 mode.
+ */
+#define CFG_PLPRCR ( ((0x1 << PLPRCR_MF_SHIFT) & PLPRCR_MF_MSK) | \
+ PLPRCR_SPLSS | \
+ PLPRCR_TEXPS | \
+ PLPRCR_TMIST \
+ )
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register UM 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+
+#define CFG_SCCR ( SCCR_TBS | /* timebase = GCLK/2 */ \
+ SCCR_COM00 | /* full strength CLKOUT */ \
+ SCCR_DFSYNC00 | /* SYNCLK / 1 (normal) */ \
+ SCCR_DFBRG00 | /* BRGCLK / 1 (normal) */ \
+ SCCR_DFNL000 | \
+ SCCR_DFNH000 \
+ )
+
+/*-----------------------------------------------------------------------
+ * DER - Debug Enable Register UM 37-46
+ *-----------------------------------------------------------------------
+ * Mask all events that can cause entry into debug mode
+ */
+#define CFG_DER 0
+
+/*
+ * Initialize Memory Controller:
+ *
+ * BR0 and OR0 (FLASH memory)
+ */
+#define FLASH_BASE0_PRELIM FLASH_BASE
+
+/*
+ * Flash address mask
+ */
+#define CFG_PRELIM_OR_AM 0xfe000000
+
+/*
+ * FLASH timing:
+ * 33 Mhz bus with ACS = 11, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 1
+ */
+#define CFG_OR_TIMING_FLASH ( OR_CSNT_SAM | \
+ OR_ACS_DIV2 | \
+ OR_BI | \
+ OR_SCY_2_CLK | \
+ OR_TRLX | \
+ OR_EHTR \
+ )
+
+#define CFG_OR0_PRELIM ( CFG_PRELIM_OR_AM | \
+ CFG_OR_TIMING_FLASH \
+ )
+
+#define CFG_BR0_PRELIM ( (FLASH_BASE0_PRELIM & BR_BA_MSK) | \
+ BR_MS_GPCM | \
+ BR_PS_8 | \
+ BR_V \
+ )
+
+/*
+ * SDRAM configuration
+ */
+#define CFG_OR1_AM 0xfc000000
+#define CFG_OR1 ( (CFG_OR1_AM & OR_AM_MSK) | \
+ OR_CSNT_SAM \
+ )
+
+#define CFG_BR1 ( (SDRAM_BASE & BR_BA_MSK) | \
+ BR_MS_UPMA | \
+ BR_PS_32 | \
+ BR_V \
+ )
+
+/*
+ * Refresh rate 7.8 us (= 64 ms / 8K = 31.2 uS quad bursts) for one bank
+ * of 256 MBit SDRAM
+ */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16
+
+/*
+ * Periodic timer for refresh @ 33 MHz system clock
+ */
+#define CFG_MAMR_PTA 64
+
+/*
+ * MAMR settings for SDRAM
+ */
+#define CFG_MAMR_8COL ( (CFG_MAMR_PTA << MAMR_PTA_SHIFT) | \
+ MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | \
+ MAMR_DSA_1_CYCL | \
+ MAMR_G0CLA_A10 | \
+ MAMR_RLFA_1X | \
+ MAMR_WLFA_1X | \
+ MAMR_TLFA_4X \
+ )
+
+/*
+ * CS2* configuration for Disk On Chip:
+ * 33 MHz bus with TRLX=1, ACS=11, CSNT=1, EBDF=1, SCY=2, EHTR=1,
+ * no burst.
+ */
+#define CFG_OR2_PRELIM ( (0xffff0000 & OR_AM_MSK) | \
+ OR_CSNT_SAM | \
+ OR_ACS_DIV2 | \
+ OR_BI | \
+ OR_SCY_2_CLK | \
+ OR_TRLX | \
+ OR_EHTR \
+ )
+
+#define CFG_BR2_PRELIM ( (DOC_BASE & BR_BA_MSK) | \
+ BR_PS_8 | \
+ BR_MS_GPCM | \
+ BR_V \
+ )
+
+/*
+ * CS3* configuration for FPGA:
+ * 33 MHz bus with SCY=15, no burst.
+ * The FPGA uses TA and TEA to terminate bus cycles, but we
+ * clear SETA and set the cycle length to a large number so that
+ * the cycle will still complete even if there is a configuration
+ * error that prevents TA from asserting on FPGA accesss.
+ */
+#define CFG_OR3_PRELIM ( (0xfc000000 & OR_AM_MSK) | \
+ OR_SCY_15_CLK | \
+ OR_BI \
+ )
+
+#define CFG_BR3_PRELIM ( (FPGA_BASE & BR_BA_MSK) | \
+ BR_PS_32 | \
+ BR_MS_GPCM | \
+ BR_V \
+ )
+/*
+ * CS4* configuration for FPGA SelectMap configuration interface.
+ * 33 MHz bus, UPMB, no burst. Do not assert GPLB5 on falling edge
+ * of GCLK1_50
+ */
+#define CFG_OR4_PRELIM ( (0xffff0000 & OR_AM_MSK) | \
+ OR_G5LS | \
+ OR_BI \
+ )
+
+#define CFG_BR4_PRELIM ( (SELECTMAP_BASE & BR_BA_MSK) | \
+ BR_PS_8 | \
+ BR_MS_UPMB | \
+ BR_V \
+ )
+
+/*
+ * CS5* configuration for Mil-Std 1553 databus interface.
+ * 33 MHz bus, GPCM, no burst.
+ * The 1553 interface uses TA and TEA to terminate bus cycles,
+ * but we clear SETA and set the cycle length to a large number so that
+ * the cycle will still complete even if there is a configuration
+ * error that prevents TA from asserting on FPGA accesss.
+ */
+#define CFG_OR5_PRELIM ( (0xffff0000 & OR_AM_MSK) | \
+ OR_SCY_15_CLK | \
+ OR_EHTR | \
+ OR_TRLX | \
+ OR_CSNT_SAM | \
+ OR_BI \
+ )
+
+#define CFG_BR5_PRELIM ( (M1553_BASE & BR_BA_MSK) | \
+ BR_PS_16 | \
+ BR_MS_GPCM | \
+ BR_V \
+ )
+
+/*
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Disk On Chip (millenium) configuration
+ */
+#define CFG_MAX_DOC_DEVICE 1
+#undef CFG_DOC_SUPPORT_2000
+#define CFG_DOC_SUPPORT_MILLENNIUM
+#undef CFG_DOC_PASSIVE_PROBE
+
+/*
+ * FEC interrupt assignment
+ */
+#define FEC_INTERRUPT SIU_LEVEL1
+
+/*
+ * Sanity checks
+ */
+#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET)
+#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured
+#endif
+
+#endif /* __CONFIG_GEN860T_H */
+
+/* vim: set ts=4 tw=78 ai shiftwidth=4: */