| // SPDX-License-Identifier: GPL-2.0 |
| |
| #include <dt-bindings/input/input.h> |
| #include "tegra30.dtsi" |
| |
| / { |
| chosen { |
| stdout-path = &uartd; |
| }; |
| |
| aliases { |
| i2c0 = &pwr_i2c; |
| i2c1 = &gen2_i2c; |
| |
| mmc0 = &sdmmc4; /* eMMC */ |
| |
| rtc0 = &pmic; |
| rtc1 = "/rtc@7000e000"; |
| |
| spi0 = &dsi_spi; |
| |
| usb0 = µ_usb; |
| }; |
| |
| memory { |
| device_type = "memory"; |
| reg = <0x80000000 0x40000000>; |
| }; |
| |
| host1x@50000000 { |
| dc@54200000 { |
| rgb { |
| status = "okay"; |
| |
| nvidia,panel = <&bridge>; |
| }; |
| }; |
| }; |
| |
| uartd: serial@70006300 { |
| status = "okay"; |
| }; |
| |
| gen2_i2c: i2c@7000c400 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| backlight: lm3533@36 { |
| compatible = "ti,lm3533"; |
| reg = <0x36>; |
| |
| enable-gpios = <&gpio TEGRA_GPIO(N, 6) GPIO_ACTIVE_HIGH>; |
| default-brightness-level = <128>; |
| }; |
| |
| muic@44 { |
| compatible = "maxim,max14526-muic"; |
| reg = <0x44>; |
| |
| maxim,ap-usb; |
| |
| usif-gpios = <&gpio TEGRA_GPIO(Y, 3) GPIO_ACTIVE_HIGH>; |
| dp2t-gpios = <&gpio TEGRA_GPIO(CC, 2) GPIO_ACTIVE_HIGH>; |
| }; |
| }; |
| |
| pwr_i2c: i2c@7000d000 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| pmic: max77663@1c { |
| compatible = "maxim,max77663"; |
| reg = <0x1c>; |
| |
| interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; |
| #interrupt-cells = <2>; |
| interrupt-controller; |
| |
| #gpio-cells = <2>; |
| gpio-controller; |
| |
| system-power-controller; |
| |
| regulators { |
| vdd_1v8_vio: sd2 { |
| regulator-name = "vdd_1v8_gen"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| avdd_3v3_periph: ldo2 { |
| regulator-name = "avdd_usb"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vdd_usd: ldo3 { |
| regulator-name = "vdd_sdmmc3"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| vcore_emmc: ldo5 { |
| regulator-name = "vdd_ddr_rx"; |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| regulator-boot-on; |
| }; |
| }; |
| }; |
| }; |
| |
| dsi_spi: spi@7000dc00 { |
| status = "okay"; |
| spi-max-frequency = <25000000>; |
| |
| bridge: bridge-spi@2 { |
| compatible = "solomon,ssd2825"; |
| reg = <2>; |
| |
| spi-cpol; |
| spi-cpha; |
| |
| spi-max-frequency = <1000000>; |
| |
| power-gpios = <&gpio TEGRA_GPIO(B, 1) GPIO_ACTIVE_HIGH>; |
| reset-gpios = <&gpio TEGRA_GPIO(O, 2) GPIO_ACTIVE_HIGH>; |
| |
| clocks = <&ssd2825_refclk>; |
| clock-names = "tx_clk"; |
| |
| panel = <&panel>; |
| }; |
| }; |
| |
| sdmmc4: sdhci@78000600 { |
| status = "okay"; |
| bus-width = <8>; |
| non-removable; |
| |
| vmmc-supply = <&vcore_emmc>; |
| vqmmc-supply = <&vdd_1v8_vio>; |
| }; |
| |
| micro_usb: usb@7d000000 { |
| status = "okay"; |
| dr_mode = "otg"; |
| }; |
| |
| usb-phy@7d000000 { |
| status = "okay"; |
| nvidia,hssync-start-delay = <0>; |
| nvidia,xcvr-lsfslew = <2>; |
| nvidia,xcvr-lsrslew = <2>; |
| vbus-supply = <&avdd_3v3_periph>; |
| }; |
| |
| /* PMIC has a built-in 32KHz oscillator which is used by PMC */ |
| clk32k_in: clock-32k { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "pmic-oscillator"; |
| }; |
| |
| ssd2825_refclk: clock-ssd2825 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24000000>; |
| clock-output-names = "ssd2825-refclk"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| key-power { |
| label = "Power"; |
| gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_ENTER>; |
| }; |
| |
| key-volume-down { |
| label = "Volume Down"; |
| gpios = <&gpio TEGRA_GPIO(O, 4) GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_DOWN>; |
| }; |
| }; |
| }; |