diff --git a/CHANGELOG b/CHANGELOG
index b597d59..09ad4f6 100644
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -2,6 +2,20 @@
 Changes since U-Boot 0.3.1:
 ======================================================================
 
+* Add support for Promess ATC board
+
+* Patch by Keith Outwater, 28 Apr 2003:
+  - Miscellaneous corrections and additions to GEN860T board specific code.
+  - Added GEN860_SC variant to GEN860T.
+  - Miscellaneous corrections to GEN860T documentation.
+  - Correct duplicate entry in U-Boot CREDITS file.
+  - Add GEN860T_SC entry in MAINTAINERS file.
+  - Update CREDITS file with GEN860T_SC info.
+
+* Update Smiths Aerospace addresses in MAINTAINERS file
+
+* Fix error handling in hush's version of "run" command
+
 * LWMON extensions:
   - Splashscreen support
   - modem support
diff --git a/CREDITS b/CREDITS
index 74b0f9e..3126c88 100644
--- a/CREDITS
+++ b/CREDITS
@@ -213,12 +213,8 @@
 W: www.elinos.com
 
 N: Keith Outwater
-E: Keith_Outwater@mvis.com
-D: Support for GEN860T board
-
-N: Keith Outwater
 E: keith_outwater@mvis.com
-D: Support for generic/custom MPC860T board (GEN860T)
+D: Support for generic/custom MPC860T boards (GEN860T, GEN860T_SC)
 
 N: Frank Panno
 E: fpanno@delphintech.com
diff --git a/MAINTAINERS b/MAINTAINERS
index 332e413..7942a02 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -28,7 +28,7 @@
 
 	NETVIA			MPC8xx
 
-Jerry Van Baren <vanbaren_gerald@si.com>
+Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
 
 	sacsng			MPC8260
 
@@ -80,6 +80,11 @@
 	CU824			MPC8240
 	Sandpoint8240		MPC8240
 
+	ATC			MPC8250
+	PM825			MPC8250
+
+	TQM8255			MPC8255
+
 	CPU86			MPC8260
 	PM826			MPC8260
 	TQM8260			MPC8260
@@ -87,7 +92,7 @@
 	PCIPPC2			MPC750
 	PCIPPC6			MPC750
 
-Jon Diekema <diekema_jon@si.com>
+Jon Diekema <jon.diekema@smiths-aerospace.com>
 
 	sbc8260			MPC8260
 
@@ -160,6 +165,7 @@
 Keith Outwater <Keith_Outwater@mvis.com>
 
 	GEN860T			MPC860T
+	GEN860T_SC		MPC860T
 
 Frank Panno <fpanno@delphintech.com>
 
diff --git a/MAKEALL b/MAKEALL
index c3a7516..030d5c2 100644
--- a/MAKEALL
+++ b/MAKEALL
@@ -26,16 +26,17 @@
 	ADS860		AMX860		c2mon		CCM		\
 	cogent_mpc8xx	ESTEEM192E	ETX094		ELPT860		\
 	FADS823		FADS850SAR	FADS860T	FLAGADM		\
-	FPS850L		GEN860T		GENIETV		GTH		\
-	hermes		IAD210		ICU862_100MHz	IP860		\
-	IVML24		IVML24_128	IVML24_256	IVMS8		\
-	IVMS8_128	IVMS8_256	KUP4K           LANTEC	        \
-	lwmon   	MBX		MBX860T		MHPC		\
-	MVS1		NETVIA		NX823		pcu_e		\
-	R360MPI		RPXClassic	RPXlite		RRvision	\
-	SM850		SPD823TS	svm_sc8xx	SXNI855T	\
-	TOP860		TQM823L		TQM823L_LCD	TQM850L		\
-	TQM855L		TQM860L		TTTech		v37		\
+	FPS850L		GEN860T		GEN860T_SC	GENIETV		\
+	GTH		hermes		IAD210		ICU862_100MHz	\
+	IP860		IVML24		IVML24_128	IVML24_256	\
+	IVMS8		IVMS8_128	IVMS8_256	KUP4K           \
+	LANTEC	        lwmon   	MBX		MBX860T		\
+	MHPC		MVS1		NETVIA		NX823		\
+	pcu_e		R360MPI		RPXClassic	RPXlite		\
+	RRvision	SM850		SPD823TS	svm_sc8xx	\
+	SXNI855T	TOP860		TQM823L		TQM823L_LCD	\
+	TQM850L		TQM855L		TQM860L		TTTech		\
+	v37								\
 "
 
 #########################################################################
@@ -62,14 +63,15 @@
 "
 
 #########################################################################
-## MPC8260 Systems
+## MPC8260 Systems (includes 8250, 8255 etc.)
 #########################################################################
 
 LIST_8260="	\
-	cogent_mpc8260	CPU86		ep8260		gw8260		\
-	hymod		IPHASE4539	MPC8260ADS	MPC8266ADS	\
-	PM826		ppmc8260	RPXsuper	rsdproto	\
-	sacsng		sbc8260		SCM		TQM8260		\
+	ATC		cogent_mpc8260	CPU86		ep8260		\
+	gw8260		hymod		IPHASE4539	MPC8260ADS	\
+	MPC8266ADS	PM826		ppmc8260	RPXsuper	\
+	rsdproto	sacsng		sbc8260		SCM		\
+	TQM8260								\
 "
 
 #########################################################################
diff --git a/Makefile b/Makefile
index 2b4f759..cf8abd6 100644
--- a/Makefile
+++ b/Makefile
@@ -212,8 +212,16 @@
 FLAGADM_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx flagadm
 
+xtract_GEN860T = $(subst _SC,,$(subst _config,,$1))
+
+GEN860T_SC_config	\
 GEN860T_config: unconfig
-	@./mkconfig $(@:_config=) ppc mpc8xx gen860t
+	@ >include/config.h
+	@[ -z "$(findstring _SC,$@)" ] || \
+		{ echo "#define CONFIG_SC" >>include/config.h ; \
+		  echo "With reduced H/W feature set (SC)..." ; \
+		}
+	@./mkconfig -a $(call xtract_GEN860T,$@) ppc mpc8xx gen860t
 
 GENIETV_config:	unconfig
 	@./mkconfig $(@:_config=) ppc mpc8xx genietv
@@ -575,11 +583,13 @@
 SCM_config:		unconfig
 	@./mkconfig $(@:_config=) ppc mpc8260 SCM siemens
 
+TQM8255_config	\
 TQM8260_config	\
 TQM8260_L2_config	\
 TQM8255_266MHz_config	\
 TQM8260_266MHz_config	\
 TQM8260_L2_266MHz_config \
+TQM8255_300MHz_config	\
 TQM8260_300MHz_config:	unconfig
 	@ >include/config.h
 	@if [ "$(findstring _L2_,$@)" ] ; then \
@@ -601,6 +611,9 @@
 		{ echo "#define CONFIG_MPC8255"	>>include/config.h ; }
 	@./mkconfig -a TQM8260 ppc mpc8260 tqm8260
 
+atc_config:	unconfig
+	@./mkconfig $(@:_config=) ppc mpc8260 atc
+
 #########################################################################
 ## 74xx/7xx Systems
 #########################################################################
diff --git a/README b/README
index dcc4a7a..1deb82c 100644
--- a/README
+++ b/README
@@ -180,7 +180,7 @@
 		Files specific to EVB64260   boards
 - board/fads	Files specific to FADS	     boards
 - board/flagadm Files specific to FLAGADM    boards
-- board/gen860t Files specific to GEN860T    boards
+- board/gen860t Files specific to GEN860T and GEN860T_SC    boards
 - board/genietv Files specific to GENIETV    boards
 - board/gth	Files specific to GTH	     boards
 - board/hermes	Files specific to HERMES     boards
diff --git a/board/atc/Makefile b/board/atc/Makefile
new file mode 100644
index 0000000..35b8428
--- /dev/null
+++ b/board/atc/Makefile
@@ -0,0 +1,40 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= lib$(BOARD).a
+
+OBJS	= $(BOARD).o flash.o
+
+$(LIB):	.depend $(OBJS)
+	$(AR) crv $@ $^
+
+#########################################################################
+
+.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
+		$(CC) -M $(CFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
+
+sinclude .depend
+
+#########################################################################
diff --git a/board/atc/atc.c b/board/atc/atc.c
new file mode 100644
index 0000000..3547f41
--- /dev/null
+++ b/board/atc/atc.c
@@ -0,0 +1,366 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <ioports.h>
+#include <mpc8260.h>
+
+/*
+ * I/O Port configuration table
+ *
+ * if conf is 1, then that port pin will be configured at boot time
+ * according to the five values podr/pdir/ppar/psor/pdat for that entry
+ */
+
+const iop_conf_t iop_conf_tab[4][32] = {
+
+    /* Port A configuration */
+    {	/*	      conf ppar psor pdir podr pdat */
+	/* PA31 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII COL */
+	/* PA30 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII CRS */
+	/* PA29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC1 MII TX_ER */
+	/* PA28 */ {   1,   1,   1,   1,   0,   0   }, /* FCC1 MII TX_EN */
+	/* PA27 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII RX_DV */
+	/* PA26 */ {   1,   1,   1,   0,   0,   0   }, /* FCC1 MII RX_ER */
+	/* PA25 */ {   1,   0,   0,   1,   0,   0   }, /* FCC2 MII MDIO */
+	/* PA24 */ {   1,   0,   0,   1,   0,   0   }, /* FCC2 MII MDC */
+	/* PA23 */ {   1,   0,   0,   1,   0,   0   }, /* FCC1 MII MDIO */
+	/* PA22 */ {   1,   0,   0,   1,   0,   0   }, /* FCC1 MII MDC */
+	/* PA21 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[3] */
+	/* PA20 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[2] */
+	/* PA19 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[1] */
+	/* PA18 */ {   1,   1,   0,   1,   0,   0   }, /* FCC1 MII TxD[0] */
+	/* PA17 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[0] */
+	/* PA16 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[1] */
+	/* PA15 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[2] */
+	/* PA14 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RxD[3] */
+	/* PA13 */ {   1,   0,   0,   1,   0,   0   }, /* FCC2 MII TXSL1 */
+	/* PA12 */ {   1,   0,   0,   1,   0,   1   }, /* FCC2 MII TXSL0 */
+	/* PA11 */ {   1,   0,   0,   1,   0,   0   }, /* FCC1 MII TXSL1 */
+	/* PA10 */ {   1,   0,   0,   1,   0,   1   }, /* FCC1 MII TXSL0 */
+#if 1
+	/* PA9  */ {   0,   1,   0,   1,   0,   0   }, /* SMC2 TXD */
+	/* PA8  */ {   0,   1,   0,   0,   0,   0   }, /* SMC2 RXD */
+#else
+	/* PA9  */ {   1,   1,   0,   1,   0,   0   }, /* SMC2 TXD */
+	/* PA8  */ {   1,   1,   0,   0,   0,   0   }, /* SMC2 RXD */
+#endif
+	/* PA7  */ {   0,   0,   0,   0,   0,   0   }, /* PA7 */
+	/* PA6  */ {   1,   0,   0,   1,   0,   1   }, /* FCC2 MII PAUSE */
+	/* PA5  */ {   1,   0,   0,   1,   0,   1   }, /* FCC1 MII PAUSE */
+	/* PA4  */ {   1,   0,   0,   1,   0,   0   }, /* FCC2 MII PWRDN */
+	/* PA3  */ {   1,   0,   0,   1,   0,   0   }, /* FCC1 MII PWRDN */
+	/* PA2  */ {   0,   0,   0,   0,   0,   0   }, /* PA2 */
+	/* PA1  */ {   1,   0,   0,   0,   0,   0   }, /* FCC2 MII MDINT */
+	/* PA0  */ {   1,   0,   0,   1,   0,   0   }  /* FCC1 MII MDINT */
+    },
+
+    /* Port B configuration */
+    {   /*	      conf ppar psor pdir podr pdat */
+	/* PB31 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TX_ER */
+	/* PB30 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_DV */
+	/* PB29 */ {   1,   1,   1,   1,   0,   0   }, /* FCC2 MII TX_EN */
+	/* PB28 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_ER */
+	/* PB27 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII COL */
+	/* PB26 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII CRS */
+	/* PB25 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[3] */
+	/* PB24 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[2] */
+	/* PB23 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[1] */
+	/* PB22 */ {   1,   1,   0,   1,   0,   0   }, /* FCC2 MII TxD[0] */
+	/* PB21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[0] */
+	/* PB20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[1] */
+	/* PB19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[2] */
+	/* PB18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RxD[3] */
+	/* PB17 */ {   0,   0,   0,   0,   0,   0   }, /* PB17 */
+	/* PB16 */ {   0,   0,   0,   0,   0,   0   }, /* PB16 */
+	/* PB15 */ {   0,   0,   0,   0,   0,   0   }, /* PB15 */
+	/* PB14 */ {   0,   0,   0,   0,   0,   0   }, /* PB14 */
+	/* PB13 */ {   0,   0,   0,   0,   0,   0   }, /* PB13 */
+	/* PB12 */ {   0,   0,   0,   0,   0,   0   }, /* PB12 */
+	/* PB11 */ {   0,   0,   0,   0,   0,   0   }, /* PB11 */
+	/* PB10 */ {   0,   0,   0,   0,   0,   0   }, /* PB10 */
+	/* PB9  */ {   0,   0,   0,   0,   0,   0   }, /* PB9 */
+	/* PB8  */ {   0,   0,   0,   0,   0,   0   }, /* PB8 */
+	/* PB7  */ {   0,   0,   0,   0,   0,   0   }, /* PB7 */
+	/* PB6  */ {   0,   0,   0,   0,   0,   0   }, /* PB6 */
+	/* PB5  */ {   0,   0,   0,   0,   0,   0   }, /* PB5 */
+	/* PB4  */ {   0,   0,   0,   0,   0,   0   }, /* PB4 */
+	/* PB3  */ {   0,   0,   0,   0,   0,   0   }, /* PB3 */
+	/* PB2  */ {   0,   0,   0,   0,   0,   0   }, /* PB2 */
+	/* PB1  */ {   0,   0,   0,   0,   0,   0   }, /* PB1 */
+	/* PB0  */ {   0,   0,   0,   0,   0,   0   }  /* PB0 */
+    },
+
+    /* Port C */
+    {   /*	      conf ppar psor pdir podr pdat */
+	/* PC31 */ {   0,   0,   0,   0,   0,   0   }, /* PC31 */
+	/* PC30 */ {   0,   0,   0,   0,   0,   0   }, /* PC30 */
+	/* PC29 */ {   1,   0,   0,   0,   0,   0   }, /* SCC1 CTS */
+	/* PC28 */ {   1,   0,   0,   0,   0,   0   }, /* SCC2 CTS */
+	/* PC27 */ {   0,   0,   0,   0,   0,   0   }, /* PC27 */
+	/* PC26 */ {   0,   0,   0,   0,   0,   0   }, /* PC26 */
+	/* PC25 */ {   0,   0,   0,   0,   0,   0   }, /* PC25 */
+	/* PC24 */ {   0,   0,   0,   0,   0,   0   }, /* PC24 */
+	/* PC23 */ {   0,   0,   0,   0,   0,   0   }, /* FDC37C78 DACFD */
+	/* PC22 */ {   0,   0,   0,   0,   0,   0   }, /* FDC37C78 DNFD */
+	/* PC21 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII RX_CLK */
+	/* PC20 */ {   1,   1,   0,   0,   0,   0   }, /* FCC1 MII TX_CLK */
+	/* PC19 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII RX_CLK */
+	/* PC18 */ {   1,   1,   0,   0,   0,   0   }, /* FCC2 MII TX_CLK */
+	/* PC17 */ {   0,   0,   0,   0,   0,   0   }, /* PC17 */
+	/* PC16 */ {   0,   0,   0,   0,   0,   0   }, /* PC16 */
+#if 0
+	/* PC15 */ {   0,   0,   0,   0,   0,   0   }, /* PC15 */
+#else
+	/* PC15 */ {   1,   1,   0,   1,   0,   0   }, /* PC15 */
+#endif
+	/* PC14 */ {   0,   0,   0,   0,   0,   0   }, /* PC14 */
+	/* PC13 */ {   0,   0,   0,   0,   0,   0   }, /* PC13 */
+	/* PC12 */ {   0,   0,   0,   0,   0,   0   }, /* PC12 */
+	/* PC11 */ {   0,   0,   0,   0,   0,   0   }, /* PC11 */
+	/* PC10 */ {   0,   0,   0,   0,   0,   0   }, /* PC10 */
+	/* PC9  */ {   0,   0,   0,   0,   0,   0   }, /* FC9 */
+	/* PC8  */ {   0,   0,   0,   0,   0,   0   }, /* PC8 */
+	/* PC7  */ {   0,   0,   0,   0,   0,   0   }, /* PC7 */
+	/* PC6  */ {   0,   0,   0,   0,   0,   0   }, /* PC6 */
+	/* PC5  */ {   0,   0,   0,   0,   0,   0   }, /* PC5 */
+	/* PC4  */ {   0,   0,   0,   0,   0,   0   }, /* PC4 */
+	/* PC3  */ {   0,   0,   0,   0,   0,   0   }, /* PC3 */
+	/* PC2  */ {   0,   0,   0,   0,   0,   0   }, /* PC2 */
+	/* PC1  */ {   0,   0,   0,   0,   0,   0   }, /* PC1 */
+	/* PC0  */ {   0,   0,   0,   0,   0,   0   }, /* FDC37C78 DRQFD */
+    },
+
+    /* Port D */
+    {   /*	      conf ppar psor pdir podr pdat */
+	/* PD31 */ {   1,   1,   0,   0,   0,   0   }, /* SCC1 RXD */
+	/* PD30 */ {   1,   1,   1,   1,   0,   0   }, /* SCC1 TXD */
+	/* PD29 */ {   1,   0,   0,   1,   0,   0   }, /* SCC1 RTS */
+	/* PD28 */ {   1,   1,   0,   0,   0,   0   }, /* SCC2 RXD */
+	/* PD27 */ {   1,   1,   0,   1,   0,   0   }, /* SCC2 TXD */
+	/* PD26 */ {   1,   0,   0,   1,   0,   0   }, /* SCC2 RTS */
+	/* PD25 */ {   0,   0,   0,   0,   0,   0   }, /* PD25 */
+	/* PD24 */ {   0,   0,   0,   0,   0,   0   }, /* PD24 */
+	/* PD23 */ {   0,   0,   0,   0,   0,   0   }, /* PD23 */
+	/* PD22 */ {   0,   0,   0,   0,   0,   0   }, /* PD22 */
+	/* PD21 */ {   0,   0,   0,   0,   0,   0   }, /* PD21 */
+	/* PD20 */ {   0,   0,   0,   0,   0,   0   }, /* PD20 */
+	/* PD19 */ {   0,   0,   0,   0,   0,   0   }, /* PD19 */
+	/* PD18 */ {   0,   0,   0,   0,   0,   0   }, /* PD18 */
+	/* PD17 */ {   0,   0,   0,   0,   0,   0   }, /* PD17 */
+	/* PD16 */ {   0,   0,   0,   0,   0,   0   }, /* PD16 */
+#if defined(CONFIG_SOFT_I2C)
+	/* PD15 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SDA */
+	/* PD14 */ {   1,   0,   0,   1,   1,   1   }, /* I2C SCL */
+#else
+#if defined(CONFIG_HARD_I2C)
+	/* PD15 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SDA */
+	/* PD14 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SCL */
+#else /* normal I/O port pins */
+	/* PD15 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SDA */
+	/* PD14 */ {   1,   1,   1,   0,   1,   0   }, /* I2C SCL */
+#endif
+#endif
+	/* PD13 */ {   0,   0,   0,   0,   0,   0   }, /* PD13 */
+	/* PD12 */ {   0,   0,   0,   0,   0,   0   }, /* PD12 */
+	/* PD11 */ {   0,   0,   0,   0,   0,   0   }, /* PD11 */
+	/* PD10 */ {   0,   0,   0,   0,   0,   0   }, /* PD10 */
+	/* PD9  */ {   1,   1,   0,   1,   0,   0   }, /* SMC1 TXD */
+	/* PD8  */ {   1,   1,   0,   0,   0,   0   }, /* SMC1 RXD */
+	/* PD7  */ {   0,   0,   0,   0,   0,   0   }, /* PD7 */
+	/* PD6  */ {   0,   0,   0,   0,   0,   0   }, /* PD6 */
+	/* PD5  */ {   0,   0,   0,   0,   0,   0   }, /* PD5 */
+#if 0
+	/* PD4  */ {   0,   0,   0,   0,   0,   0   }, /* PD4 */
+#else
+	/* PD4  */ {   1,   1,   1,   0,   0,   0   }, /* PD4 */
+#endif
+	/* PD3  */ {   0,   0,   0,   0,   0,   0   }, /* PD3 */
+	/* PD2  */ {   0,   0,   0,   0,   0,   0   }, /* PD2 */
+	/* PD1  */ {   0,   0,   0,   0,   0,   0   }, /* PD1 */
+	/* PD0  */ {   0,   0,   0,   0,   0,   0   }  /* PD0 */
+    }
+};
+
+/* ------------------------------------------------------------------------- */
+
+/* Check Board Identity:
+ */
+int checkboard (void)
+{
+	printf ("Board: ATC\n");
+	return 0;
+}
+
+/* ------------------------------------------------------------------------- */
+
+/* Try SDRAM initialization with P/LSDMR=sdmr and ORx=orx
+ *
+ * This routine performs standard 8260 initialization sequence
+ * and calculates the available memory size. It may be called
+ * several times to try different SDRAM configurations on both
+ * 60x and local buses.
+ */
+static long int try_init (volatile memctl8260_t * memctl, ulong sdmr,
+			  ulong orx, volatile uchar * base)
+{
+	volatile uchar c = 0xff;
+	ulong cnt, val;
+	volatile ulong *addr;
+	volatile uint *sdmr_ptr;
+	volatile uint *orx_ptr;
+	int i;
+	ulong save[32];		/* to make test non-destructive */
+	ulong maxsize;
+
+	/* We must be able to test a location outsize the maximum legal size
+	 * to find out THAT we are outside; but this address still has to be
+	 * mapped by the controller. That means, that the initial mapping has
+	 * to be (at least) twice as large as the maximum expected size.
+	 */
+	maxsize = (1 + (~orx | 0x7fff)) / 2;
+
+	/* Since CFG_SDRAM_BASE is always 0 (??), we assume that
+	 * we are configuring CS1 if base != 0
+	 */
+	sdmr_ptr = &memctl->memc_psdmr;
+	orx_ptr = &memctl->memc_or2;
+
+	*orx_ptr = orx;
+
+	/*
+	 * Quote from 8260 UM (10.4.2 SDRAM Power-On Initialization, 10-35):
+	 *
+	 * "At system reset, initialization software must set up the
+	 *  programmable parameters in the memory controller banks registers
+	 *  (ORx, BRx, P/LSDMR). After all memory parameters are configured,
+	 *  system software should execute the following initialization sequence
+	 *  for each SDRAM device.
+	 *
+	 *  1. Issue a PRECHARGE-ALL-BANKS command
+	 *  2. Issue eight CBR REFRESH commands
+	 *  3. Issue a MODE-SET command to initialize the mode register
+	 *
+	 *  The initial commands are executed by setting P/LSDMR[OP] and
+	 *  accessing the SDRAM with a single-byte transaction."
+	 *
+	 * The appropriate BRx/ORx registers have already been set when we
+	 * get here. The SDRAM can be accessed at the address CFG_SDRAM_BASE.
+	 */
+
+	*sdmr_ptr = sdmr | PSDMR_OP_PREA;
+	*base = c;
+
+	*sdmr_ptr = sdmr | PSDMR_OP_CBRR;
+	for (i = 0; i < 8; i++)
+		*base = c;
+
+	*sdmr_ptr = sdmr | PSDMR_OP_MRW;
+	*(base + CFG_MRS_OFFS) = c;	/* setting MR on address lines */
+
+	*sdmr_ptr = sdmr | PSDMR_OP_NORM | PSDMR_RFEN;
+	*base = c;
+
+	/*
+	 * Check memory range for valid RAM. A simple memory test determines
+	 * the actually available RAM size between addresses `base' and
+	 * `base + maxsize'. Some (not all) hardware errors are detected:
+	 * - short between address lines
+	 * - short between data lines
+	 */
+	i = 0;
+	for (cnt = maxsize / sizeof (long); cnt > 0; cnt >>= 1) {
+		addr = (volatile ulong *) base + cnt;	/* pointer arith! */
+		save[i++] = *addr;
+		*addr = ~cnt;
+	}
+
+	addr = (volatile ulong *) base;
+	save[i] = *addr;
+	*addr = 0;
+
+	if ((val = *addr) != 0) {
+		*addr = save[i];
+		return (0);
+	}
+
+	for (cnt = 1; cnt <= maxsize / sizeof (long); cnt <<= 1) {
+		addr = (volatile ulong *) base + cnt;	/* pointer arith! */
+		val = *addr;
+		*addr = save[--i];
+		if (val != ~cnt) {
+			/* Write the actual size to ORx
+			 */
+			*orx_ptr = orx | ~(cnt * sizeof (long) - 1);
+			return (cnt * sizeof (long));
+		}
+	}
+	return (maxsize);
+}
+
+long int initdram (int board_type)
+{
+	volatile immap_t *immap = (immap_t *) CFG_IMMR;
+	volatile memctl8260_t *memctl = &immap->im_memctl;
+
+#ifndef CFG_RAMBOOT
+	ulong size8, size9;
+#endif
+	long psize;
+
+	psize = 8 * 1024 * 1024;
+
+	memctl->memc_mptpr = CFG_MPTPR;
+	memctl->memc_psrt = CFG_PSRT;
+
+#ifndef CFG_RAMBOOT
+	/* 60x SDRAM setup:
+	 */
+	size8 = try_init (memctl, CFG_PSDMR_8COL, CFG_OR2_8COL,
+			  (uchar *) CFG_SDRAM_BASE);
+	size9 = try_init (memctl, CFG_PSDMR_9COL, CFG_OR2_9COL,
+			  (uchar *) CFG_SDRAM_BASE);
+
+	if (size8 < size9) {
+		psize = size9;
+		printf ("(60x:9COL) ");
+	} else {
+		psize = try_init (memctl, CFG_PSDMR_8COL, CFG_OR2_8COL,
+				  (uchar *) CFG_SDRAM_BASE);
+		printf ("(60x:8COL) ");
+	}
+
+#endif	/* CFG_RAMBOOT */
+
+	icache_enable ();
+
+	return (psize);
+}
+
+#if (CONFIG_COMMANDS & CFG_CMD_DOC)
+extern void doc_probe (ulong physadr);
+void doc_init (void)
+{
+	doc_probe (CFG_DOC_BASE);
+}
+#endif
diff --git a/board/atc/config.mk b/board/atc/config.mk
new file mode 100644
index 0000000..8fc82f3
--- /dev/null
+++ b/board/atc/config.mk
@@ -0,0 +1,43 @@
+#
+# (C) Copyright 2001
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# ATC boards
+#
+
+# This should be equal to the CFG_FLASH_BASE define in config_atc.h
+# for the "final" configuration, with U-Boot in flash, or the address
+# in RAM where U-Boot is loaded at for debugging.
+#
+
+ifeq ($(CONFIG_BOOT_ROM),y)
+	TEXT_BASE := 0xFF800000
+	PLATFORM_CPPFLAGS += -DCONFIG_BOOT_ROM
+else
+	TEXT_BASE := 0xFF000000
+endif
+
+# RAM version
+#TEXT_BASE := 0x100000
+
+PLATFORM_CPPFLAGS += -DTEXT_BASE=$(TEXT_BASE) -I$(TOPDIR)
diff --git a/board/atc/flash.c b/board/atc/flash.c
new file mode 100644
index 0000000..4bcf2ee
--- /dev/null
+++ b/board/atc/flash.c
@@ -0,0 +1,665 @@
+/*
+ * (C) Copyright 2003
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+flash_info_t	flash_info[CFG_MAX_FLASH_BANKS]; /* info for FLASH chips	*/
+
+/* NOTE - CONFIG_FLASH_16BIT means the CPU interface is 16-bit, it
+ *        has nothing to do with the flash chip being 8-bit or 16-bit.
+ */
+#ifdef CONFIG_FLASH_16BIT
+typedef unsigned short FLASH_PORT_WIDTH;
+typedef volatile unsigned short FLASH_PORT_WIDTHV;
+#define	FLASH_ID_MASK	0xFFFF
+#else
+typedef unsigned long FLASH_PORT_WIDTH;
+typedef volatile unsigned long FLASH_PORT_WIDTHV;
+#define	FLASH_ID_MASK	0xFFFFFFFF
+#endif
+
+#define FPW	FLASH_PORT_WIDTH
+#define FPWV	FLASH_PORT_WIDTHV
+
+#define ORMASK(size) ((-size) & OR_AM_MSK)
+
+#define FLASH_CYCLE1	0x0555
+#define FLASH_CYCLE2	0x02aa
+
+/*-----------------------------------------------------------------------
+ * Functions
+ */
+static ulong flash_get_size(FPWV *addr, flash_info_t *info);
+static void flash_reset(flash_info_t *info);
+static int write_word_intel(flash_info_t *info, FPWV *dest, FPW data);
+static int write_word_amd(flash_info_t *info, FPWV *dest, FPW data);
+static void flash_get_offsets(ulong base, flash_info_t *info);
+static flash_info_t *flash_get_info(ulong base);
+
+/*-----------------------------------------------------------------------
+ * flash_init()
+ *
+ * sets up flash_info and returns size of FLASH (bytes)
+ */
+unsigned long flash_init (void)
+{
+	unsigned long size = 0;
+	int i;
+
+	/* Init: no FLASHes known */
+	for (i=0; i < CFG_MAX_FLASH_BANKS; ++i) {
+#if 0
+		ulong flashbase = (i == 0) ? PHYS_FLASH_1 : PHYS_FLASH_2;
+#else
+		ulong flashbase = CFG_FLASH_BASE;
+#endif
+
+		memset(&flash_info[i], 0, sizeof(flash_info_t));
+
+		flash_info[i].size = 
+			flash_get_size((FPW *)flashbase, &flash_info[i]);
+
+		if (flash_info[i].flash_id == FLASH_UNKNOWN) {
+			printf ("## Unknown FLASH on Bank %d - Size = 0x%08lx\n",
+			i, flash_info[i].size);
+		}
+		
+		size += flash_info[i].size;
+	}
+
+#if CFG_MONITOR_BASE >= CFG_FLASH_BASE
+	/* monitor protection ON by default */
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_MONITOR_BASE,
+		      CFG_MONITOR_BASE+CFG_MONITOR_LEN-1,
+		      flash_get_info(CFG_MONITOR_BASE));
+#endif
+
+#ifdef	CFG_ENV_IS_IN_FLASH
+	/* ENV protection ON by default */
+	flash_protect(FLAG_PROTECT_SET,
+		      CFG_ENV_ADDR,
+		      CFG_ENV_ADDR+CFG_ENV_SIZE-1,
+		      flash_get_info(CFG_ENV_ADDR));
+#endif
+
+
+	return size ? size : 1;
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_reset(flash_info_t *info)
+{
+	FPWV *base = (FPWV *)(info->start[0]);
+
+	/* Put FLASH back in read mode */
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL)
+		*base = (FPW)0x00FF00FF;	/* Intel Read Mode */
+	else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD)
+		*base = (FPW)0x00F000F0;	/* AMD Read Mode */
+}
+
+/*-----------------------------------------------------------------------
+ */
+static void flash_get_offsets (ulong base, flash_info_t *info)
+{
+	int i;
+
+	/* set up sector start address table */
+	if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL
+	    && (info->flash_id & FLASH_BTYPE)) {
+		int bootsect_size;	/* number of bytes/boot sector	*/
+		int sect_size;		/* number of bytes/regular sector */
+
+		bootsect_size = 0x00002000 * (sizeof(FPW)/2);
+		sect_size =     0x00010000 * (sizeof(FPW)/2);
+
+		/* set sector offsets for bottom boot block type	*/
+		for (i = 0; i < 8; ++i) {
+			info->start[i] = base + (i * bootsect_size);
+		}
+		for (i = 8; i < info->sector_count; i++) {
+			info->start[i] = base + ((i - 7) * sect_size);
+		}
+	}
+	else if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_AMD
+		 && (info->flash_id & FLASH_TYPEMASK) == FLASH_AM640U) {
+
+		int sect_size;		/* number of bytes/sector */
+
+		sect_size = 0x00010000 * (sizeof(FPW)/2);
+
+		/* set up sector start address table (uniform sector type) */
+		for( i = 0; i < info->sector_count; i++ )
+			info->start[i] = base + (i * sect_size);
+	}
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+static flash_info_t *flash_get_info(ulong base)
+{
+	int i;
+	flash_info_t * info;
+	
+	for (i = 0; i < CFG_MAX_FLASH_BANKS; i ++) {
+		info = & flash_info[i];
+		if (info->start[0] <= base && base < info->start[0] + info->size)
+			break;
+	}
+	
+	return i == CFG_MAX_FLASH_BANKS ? 0 : info;
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+void flash_print_info (flash_info_t *info)
+{
+	int i;
+	uchar *boottype;
+	uchar *bootletter;
+	uchar *fmt;
+	uchar botbootletter[] = "B";
+	uchar topbootletter[] = "T";
+	uchar botboottype[] = "bottom boot sector";
+	uchar topboottype[] = "top boot sector";
+
+	if (info->flash_id == FLASH_UNKNOWN) {
+		printf ("missing or unknown FLASH type\n");
+		return;
+	}
+
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_AMD:	printf ("AMD ");		break;
+	case FLASH_MAN_BM:	printf ("BRIGHT MICRO ");	break;
+	case FLASH_MAN_FUJ:	printf ("FUJITSU ");		break;
+	case FLASH_MAN_SST:	printf ("SST ");		break;
+	case FLASH_MAN_STM:	printf ("STM ");		break;
+	case FLASH_MAN_INTEL:	printf ("INTEL ");		break;
+	default:		printf ("Unknown Vendor ");	break;
+	}
+
+	/* check for top or bottom boot, if it applies */
+	if (info->flash_id & FLASH_BTYPE) {
+		boottype = botboottype;
+		bootletter = botbootletter;
+	}
+	else {
+		boottype = topboottype;
+		bootletter = topbootletter;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_AM640U:
+		fmt = "29LV641D (64 Mbit, uniform sectors)\n";
+		break;
+        case FLASH_28F800C3B:
+        case FLASH_28F800C3T:
+		fmt = "28F800C3%s (8 Mbit, %s)\n";
+		break;
+	case FLASH_INTEL800B:
+	case FLASH_INTEL800T:
+		fmt = "28F800B3%s (8 Mbit, %s)\n";
+		break;
+        case FLASH_28F160C3B:
+        case FLASH_28F160C3T:
+		fmt = "28F160C3%s (16 Mbit, %s)\n";
+		break;
+	case FLASH_INTEL160B:
+	case FLASH_INTEL160T:
+		fmt = "28F160B3%s (16 Mbit, %s)\n";
+		break;
+        case FLASH_28F320C3B:
+        case FLASH_28F320C3T:
+		fmt = "28F320C3%s (32 Mbit, %s)\n";
+		break;
+	case FLASH_INTEL320B:
+	case FLASH_INTEL320T:
+		fmt = "28F320B3%s (32 Mbit, %s)\n";
+		break;
+        case FLASH_28F640C3B:
+        case FLASH_28F640C3T:
+		fmt = "28F640C3%s (64 Mbit, %s)\n";
+		break;
+	case FLASH_INTEL640B:
+	case FLASH_INTEL640T:
+		fmt = "28F640B3%s (64 Mbit, %s)\n";
+		break;
+	default:
+		fmt = "Unknown Chip Type\n";
+		break;
+	}
+
+	printf (fmt, bootletter, boottype);
+
+	printf ("  Size: %ld MB in %d Sectors\n",
+		info->size >> 20,
+		info->sector_count);
+
+	printf ("  Sector Start Addresses:");
+
+	for (i=0; i<info->sector_count; ++i) {
+		if ((i % 5) == 0) {
+			printf ("\n   ");
+		}
+
+		printf (" %08lX%s", info->start[i],
+			info->protect[i] ? " (RO)" : "     ");
+	}
+
+	printf ("\n");
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+/*
+ * The following code cannot be run from FLASH!
+ */
+
+ulong flash_get_size (FPWV *addr, flash_info_t *info)
+{
+	/* Write auto select command: read Manufacturer ID */
+
+	/* Write auto select command sequence and test FLASH answer */
+	addr[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* for AMD, Intel ignores this */
+	addr[FLASH_CYCLE2] = (FPW)0x00550055;	/* for AMD, Intel ignores this */
+	addr[FLASH_CYCLE1] = (FPW)0x00900090;	/* selects Intel or AMD */
+
+	/* The manufacturer codes are only 1 byte, so just use 1 byte.
+	 * This works for any bus width and any FLASH device width.
+	 */
+	udelay(1000000);//psl
+	//psl	switch (addr[1] & 0xff) {
+	switch (addr[0] & 0xff) {//psl
+
+	case (uchar)AMD_MANUFACT:
+		info->flash_id = FLASH_MAN_AMD;
+		break;
+
+	case (uchar)INTEL_MANUFACT:
+		info->flash_id = FLASH_MAN_INTEL;
+		break;
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		break;
+	}
+
+	/* Check 16 bits or 32 bits of ID so work on 32 or 16 bit bus. */
+	//psl	if (info->flash_id != FLASH_UNKNOWN) switch (addr[0]) {
+	if (info->flash_id != FLASH_UNKNOWN) switch (addr[1]) {
+
+	case (FPW)AMD_ID_LV640U:	/* 29LV640 and 29LV641 have same ID */
+		info->flash_id += FLASH_AM640U;
+		info->sector_count = 128;
+		info->size = 0x00800000 * (sizeof(FPW)/2);
+		break;				/* => 8 or 16 MB	*/
+
+	case (FPW)INTEL_ID_28F800C3B:
+		info->flash_id += FLASH_28F800C3B;
+		info->sector_count = 23;
+		info->size = 0x00100000 * (sizeof(FPW)/2);
+		break;				/* => 1 or 2 MB		*/
+
+	case (FPW)INTEL_ID_28F800B3B:
+		info->flash_id += FLASH_INTEL800B;
+		info->sector_count = 23;
+		info->size = 0x00100000 * (sizeof(FPW)/2);
+		break;				/* => 1 or 2 MB		*/
+
+	case (FPW)INTEL_ID_28F160C3B:
+		info->flash_id += FLASH_28F160C3B;
+		info->sector_count = 39;
+		info->size = 0x00200000 * (sizeof(FPW)/2);
+		break;				/* => 2 or 4 MB		*/
+
+	case (FPW)INTEL_ID_28F160B3B:
+		info->flash_id += FLASH_INTEL160B;
+		info->sector_count = 39;
+		info->size = 0x00200000 * (sizeof(FPW)/2);
+		break;				/* => 2 or 4 MB		*/
+
+	case (FPW)INTEL_ID_28F320C3B:
+		info->flash_id += FLASH_28F320C3B;
+		info->sector_count = 71;
+		info->size = 0x00400000 * (sizeof(FPW)/2);
+		break;				/* => 4 or 8 MB		*/
+
+	case (FPW)INTEL_ID_28F320B3B:
+		info->flash_id += FLASH_INTEL320B;
+		info->sector_count = 71;
+		info->size = 0x00400000 * (sizeof(FPW)/2);
+		break;				/* => 4 or 8 MB		*/
+
+	case (FPW)INTEL_ID_28F640C3B:
+		info->flash_id += FLASH_28F640C3B;
+		info->sector_count = 135;
+		info->size = 0x00800000 * (sizeof(FPW)/2);
+		break;				/* => 8 or 16 MB	*/
+
+	case (FPW)INTEL_ID_28F640B3B:
+		info->flash_id += FLASH_INTEL640B;
+		info->sector_count = 135;
+		info->size = 0x00800000 * (sizeof(FPW)/2);
+		break;				/* => 8 or 16 MB	*/
+
+	default:
+		info->flash_id = FLASH_UNKNOWN;
+		info->sector_count = 0;
+		info->size = 0;
+		return (0);			/* => no or unknown flash */
+	}
+
+	flash_get_offsets((ulong)addr, info);
+
+	/* Put FLASH back in read mode */
+	flash_reset(info);
+
+	return (info->size);
+}
+
+/*-----------------------------------------------------------------------
+ */
+
+int	flash_erase (flash_info_t *info, int s_first, int s_last)
+{
+	FPWV *addr;
+	int flag, prot, sect;
+	int intel = (info->flash_id & FLASH_VENDMASK) == FLASH_MAN_INTEL;
+	ulong start, now, last;
+	int rcode = 0;
+
+	if ((s_first < 0) || (s_first > s_last)) {
+		if (info->flash_id == FLASH_UNKNOWN) {
+			printf ("- missing\n");
+		} else {
+			printf ("- no sectors to erase\n");
+		}
+		return 1;
+	}
+
+	switch (info->flash_id & FLASH_TYPEMASK) {
+	case FLASH_INTEL800B:
+	case FLASH_INTEL160B:
+	case FLASH_INTEL320B:
+	case FLASH_INTEL640B:
+	case FLASH_28F800C3B:
+	case FLASH_28F160C3B:
+	case FLASH_28F320C3B:
+	case FLASH_28F640C3B:
+	case FLASH_AM640U:
+		break;
+	case FLASH_UNKNOWN:
+	default:
+		printf ("Can't erase unknown flash type %08lx - aborted\n",
+			info->flash_id);
+		return 1;
+	}
+
+	prot = 0;
+	for (sect=s_first; sect<=s_last; ++sect) {
+		if (info->protect[sect]) {
+			prot++;
+		}
+	}
+
+	if (prot) {
+		printf ("- Warning: %d protected sectors will not be erased!\n",
+			prot);
+	} else {
+		printf ("\n");
+	}
+
+	last  = get_timer(0);
+
+	/* Start erase on unprotected sectors */
+	for (sect = s_first; sect<=s_last && rcode == 0; sect++) {
+
+		if (info->protect[sect] != 0)	/* protected, skip it */
+			continue;
+
+		/* Disable interrupts which might cause a timeout here */
+		flag = disable_interrupts();
+
+		addr = (FPWV *)(info->start[sect]);
+		if (intel) {
+			*addr = (FPW)0x00500050; /* clear status register */
+			*addr = (FPW)0x00200020; /* erase setup */
+			*addr = (FPW)0x00D000D0; /* erase confirm */
+		}
+		else {
+			/* must be AMD style if not Intel */
+			FPWV *base;		/* first address in bank */
+
+			base = (FPWV *)(info->start[0]);
+			base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
+			base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
+			base[FLASH_CYCLE1] = (FPW)0x00800080;	/* erase mode */
+			base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
+			base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
+			*addr = (FPW)0x00300030;	/* erase sector */
+		}
+
+		/* re-enable interrupts if necessary */
+		if (flag)
+			enable_interrupts();
+
+		start = get_timer(0);
+
+		/* wait at least 50us for AMD, 80us for Intel.
+		 * Let's wait 1 ms.
+		 */
+		udelay (1000);
+
+		while ((*addr & (FPW)0x00800080) != (FPW)0x00800080) {
+			if ((now = get_timer(start)) > CFG_FLASH_ERASE_TOUT) {
+				printf ("Timeout\n");
+
+				if (intel) {
+					/* suspend erase	*/
+					*addr = (FPW)0x00B000B0;
+				}
+
+				flash_reset(info);	/* reset to read mode */
+				rcode = 1;		/* failed */
+				break;
+			}
+
+			/* show that we're waiting */
+			if ((get_timer(last)) > CFG_HZ) {/* every second */
+				putc ('.');
+				last = get_timer(0);
+			}
+		}
+
+		/* show that we're waiting */
+		if ((get_timer(last)) > CFG_HZ) {	/* every second */
+			putc ('.');
+			last = get_timer(0);
+		}
+
+		flash_reset(info);	/* reset to read mode	*/
+	}
+
+	printf (" done\n");
+	return rcode;
+}
+
+/*-----------------------------------------------------------------------
+ * Copy memory to flash, returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+int write_buff (flash_info_t *info, uchar *src, ulong addr, ulong cnt)
+{
+    FPW data = 0; /* 16 or 32 bit word, matches flash bus width on MPC8XX */
+    int bytes;	  /* number of bytes to program in current word		*/
+    int left;	  /* number of bytes left to program			*/
+    int i, res;
+
+    for (left = cnt, res = 0;
+	 left > 0 && res == 0;
+	 addr += sizeof(data), left -= sizeof(data) - bytes) {
+
+        bytes = addr & (sizeof(data) - 1);
+        addr &= ~(sizeof(data) - 1);
+
+	/* combine source and destination data so can program
+	 * an entire word of 16 or 32 bits
+	 */
+        for (i = 0; i < sizeof(data); i++) {
+            data <<= 8;
+            if (i < bytes || i - bytes >= left )
+		data += *((uchar *)addr + i);
+	    else
+		data += *src++;
+	}
+
+	/* write one word to the flash */
+	switch (info->flash_id & FLASH_VENDMASK) {
+	case FLASH_MAN_AMD:
+		res = write_word_amd(info, (FPWV *)addr, data);
+		break;
+	case FLASH_MAN_INTEL:
+		res = write_word_intel(info, (FPWV *)addr, data);
+		break;
+	default:
+		/* unknown flash type, error! */
+		printf ("missing or unknown FLASH type\n");
+		res = 1;	/* not really a timeout, but gives error */
+		break;
+	}
+    }
+
+    return (res);
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word to Flash for AMD FLASH
+ * A word is 16 or 32 bits, whichever the bus width of the flash bank
+ * (not an individual chip) is.
+ *
+ * returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_word_amd (flash_info_t *info, FPWV *dest, FPW data)
+{
+    ulong start;
+    int flag;
+    int res = 0;	/* result, assume success	*/
+    FPWV *base;		/* first address in flash bank	*/
+
+    /* Check if Flash is (sufficiently) erased */
+    if ((*dest & data) != data) {
+	return (2);
+    }
+
+
+    base = (FPWV *)(info->start[0]);
+
+    /* Disable interrupts which might cause a timeout here */
+    flag = disable_interrupts();
+
+    base[FLASH_CYCLE1] = (FPW)0x00AA00AA;	/* unlock */
+    base[FLASH_CYCLE2] = (FPW)0x00550055;	/* unlock */
+    base[FLASH_CYCLE1] = (FPW)0x00A000A0;	/* selects program mode */
+
+    *dest = data;		/* start programming the data	*/
+
+    /* re-enable interrupts if necessary */
+    if (flag)
+	enable_interrupts();
+
+    start = get_timer (0);
+
+    /* data polling for D7 */
+    while (res == 0 && (*dest & (FPW)0x00800080) != (data & (FPW)0x00800080)) {
+	if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
+	    *dest = (FPW)0x00F000F0;	/* reset bank */
+	    res = 1;
+	}
+    }
+
+    return (res);
+}
+
+/*-----------------------------------------------------------------------
+ * Write a word to Flash for Intel FLASH
+ * A word is 16 or 32 bits, whichever the bus width of the flash bank
+ * (not an individual chip) is.
+ *
+ * returns:
+ * 0 - OK
+ * 1 - write timeout
+ * 2 - Flash not erased
+ */
+static int write_word_intel (flash_info_t *info, FPWV *dest, FPW data)
+{
+    ulong start;
+    int flag;
+    int res = 0;	/* result, assume success	*/
+
+    /* Check if Flash is (sufficiently) erased */
+    if ((*dest & data) != data) {
+	return (2);
+    }
+
+    /* Disable interrupts which might cause a timeout here */
+    flag = disable_interrupts();
+
+    *dest = (FPW)0x00500050;	/* clear status register	*/
+    *dest = (FPW)0x00FF00FF;	/* make sure in read mode	*/
+    *dest = (FPW)0x00400040;	/* program setup		*/
+
+    *dest = data;		/* start programming the data	*/
+
+    /* re-enable interrupts if necessary */
+    if (flag)
+	enable_interrupts();
+
+    start = get_timer (0);
+
+    while (res == 0 && (*dest & (FPW)0x00800080) != (FPW)0x00800080) {
+	if (get_timer(start) > CFG_FLASH_WRITE_TOUT) {
+	    *dest = (FPW)0x00B000B0;	/* Suspend program	*/
+	    res = 1;
+	}
+    }
+
+    if (res == 0 && (*dest & (FPW)0x00100010))
+	res = 1;	/* write failed, time out error is close enough	*/
+
+    *dest = (FPW)0x00500050;	/* clear status register	*/
+    *dest = (FPW)0x00FF00FF;	/* make sure in read mode	*/
+
+    return (res);
+}
diff --git a/board/atc/u-boot.lds b/board/atc/u-boot.lds
new file mode 100644
index 0000000..5df4cdb
--- /dev/null
+++ b/board/atc/u-boot.lds
@@ -0,0 +1,118 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    cpu/mpc8260/start.o	(.text)
+    *(.text)
+    common/environment.o(.text)
+    *(.fixup)
+    *(.got1)
+    . = ALIGN(16);
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x0FFF) & 0xFFFFF000;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+  __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(4096);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(4096);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  _end = . ;
+  PROVIDE (end = .);
+}
+
diff --git a/board/gen860t/README b/board/gen860t/README
index 761ceed..7c03f93 100644
--- a/board/gen860t/README
+++ b/board/gen860t/README
@@ -1,8 +1,7 @@
-
 This directory contains board specific code for a generic MPC860T based
 embedded computer, called 'GEN860T'.  The design is generic in the sense that
 common, readily available components are used and that the architecture of the
-system is i(relatively) straightforward:
+system is relatively straightforward:
 
 	One eight bit wide boot (FLASH) memory
 	32 bit main memory using SDRAM
@@ -23,14 +22,14 @@
 quality of this U-Boot port.
 
 Here are the salient features of the system:
-Clock						:	33 Mhz oscillator
-Processor core frequency	:	66 Mhz  if in 1:2:1 mode; can also run 1:1
-Bus frequency				:	33 Mhz
+Clock						:	33.3 Mhz oscillator
+Processor core frequency	:	66.6 Mhz  if in 1:2:1 mode; can also run 1:1
+Bus frequency				:	33.3 Mhz
 
 Main memory:
 	Type	: SDRAM
 	Width	: 32 bits
-	Size	: 64 megabytes
+	Size	: 64 mibibytes
 	Chip	: Two Micron MT48LC16M16A2TG-7E
 	CS		: MPC860T CS1*/UPMA
 	UPMA CONNECTIONS:
@@ -42,7 +41,7 @@
 Boot memory:
 	Type	: FLASH
 	Width	: 8 bits
-	Size	: 16 megabytes
+	Size	: 16 mibibytes
 	Chip	: One Intel 28F128J3A (StrataFlash)
 	CS		: MPC860T CS0*/GPCM (this is the "boot" chip select)
 
@@ -56,7 +55,7 @@
 Filesystem memory:
 	Type	: NAND FLASH (Toshiba)
 	Width	: 8 bits (i.e. interface to DOC is 8 bits)
-	Size	: 32 megabytes
+	Size	: 32 mibibytes
 	Chip	: One DiskOnCHip Millenium Plus (DOC 2000+)
 	CS		: MPC860T CS2*/GPCM
 
@@ -92,6 +91,12 @@
 	Mil-Std 1553 databus interface on CS5*/GPCM.
 	Audio sounder (beeper) with digital volume control connected to SPKROUT.
 
+SC variant:
+	A reduced-feature version of the GEN860T port is also supported: GEN860T_SC.
+	The 'SC' variant only provides support for the Virtex FPGA, SDRAM main
+	memory, EEPROM and flash memory.  The system clock frequency is reduced
+	to 24 MHz.
+
 Issues:
 	The DOC 2000+ returns 0x40 as its device ID when probed using the method
 	desxribed in the DOC datasheet.  Unfortunately, the U-Boot DOC driver
@@ -105,11 +110,11 @@
 	in MTD for this device.  I wish I had known this sooner :(
 
 The GEN860T board specific files and configuration is based on the work
-of others who have contributed to U-Boot. The copright and license notices
+of others who have contributed to U-Boot. The copyright and license notices
 of these authors have been retained wherever their code has been reused.
 All new code to support the GEN860T board is:
 
-	(C) Copyright 2001-2002
+	(C) Copyright 2001-2003
 	Keith Outwater (keith_outwater@mvis.com)
 
 and the following license applies:
diff --git a/board/gen860t/gen860t.c b/board/gen860t/gen860t.c
index 16a3262..094eeef 100644
--- a/board/gen860t/gen860t.c
+++ b/board/gen860t/gen860t.c
@@ -271,18 +271,12 @@
 int
 last_stage_init(void)
 {
+#if !defined(CONFIG_SC)
 	unsigned char buf[256];
 	int i;
 
 	/*
-	 * Set LEDs here since status LED init code has already run
-	 */
-	status_led_set(STATUS_LED_BIT1, STATUS_LED_ON);
-	status_led_set(STATUS_LED_BIT3, STATUS_LED_ON);
-
-	/*
-	 * Turn the beeper volume all the way down in case this is a warm
-	 * boot.
+	 * Turn the beeper volume all the way down in case this is a warm boot.
 	 */
 	set_beeper_volume(-64);
 	init_beeper();
@@ -294,6 +288,18 @@
 	if (i > 0) {
 		do_beeper(buf);
 	}
+#endif
 	return 0;
 }
+
+/*
+ * Stub to make POST code happy.  Can't self-poweroff, so just hang.
+ */
+void
+board_poweroff(void)
+{
+	puts("### Please power off the board ###\n");
+    while (1);
+}
+
 /* vim: set ts=4 sw=4 tw=78 : */
diff --git a/board/gen860t/ioport.c b/board/gen860t/ioport.c
index 5d6524d..7b3ebd4 100644
--- a/board/gen860t/ioport.c
+++ b/board/gen860t/ioport.c
@@ -42,8 +42,9 @@
 const mpc8xx_iop_conf_t iop_conf_tab[NUM_PORTS][PORT_BITS] = {
     /*
 	 * Port A configuration
-	 * Pin		Signal				Type	Active		Initial state
-	 * PA7 		fpgaProgramLowOut	Out		Low			High
+	 * Pin	Signal					Type	Active	Initial state
+	 * PA7 	fpgaProgramLowOut		Out		Low			High
+	 * PA1 	fpgaCoreVoltageFailLow	In		Low			N/A
 	 */
     {	/*	    conf ppar psor pdir podr pdat pint	   function 		*/
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }, /* No pin			*/
@@ -62,22 +63,32 @@
 	/* PA4  */ { 1,   0,   0,   1,   0,   0,   0 }, /* red bicolor LED 0*/
 	/* PA3  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PA2  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
+#if !defined(CONFIG_SC)
+	/* PA1  */ { 1,   0,   0,   0,   0,   0,   0 }, /*	fpgaCoreVoltageFail*/
+#else
 	/* PA1  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
+#endif
 	/* PA0  */ { 0,   0,   0,   0,   0,   0,   0 }  /*	*/
     },
 
 	/*
+	 * Port B configuration
 	 * Pin		Signal			Type		Active		Initial state
 	 * PB14		docBusyLowIn	In			Low			X
 	 * PB15		gpio1Sig		Out			High		Low
 	 * PB16		fpgaDoneBi		In			High		X
-	 * PB17		swBitOkLowOut	Out			Low			Low
+	 * PB17		swBitOkLowOut	Out			Low			High
 	 * PB19		speakerVolSig	Out/Hi-Z	High/Low	High (Hi-Z)
 	 * PB22		fpgaInitLowBi	In			Low			X
 	 * PB23		batteryOkSig	In			High		X
-     */
-    {	/*	    conf ppar psor pdir podr pdat pint 	  function			*/
-	/* PB31 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
+	 * PB31		pulseCatcherClr	Out			High		0
+	 */
+	{	/*	    conf ppar psor pdir podr pdat pint 	  function			*/
+#if !defined(CONFIG_SC)
+	/* PB31 */ { 0,	  0,   0,   0,   0,   0,   0 }, /*	*/
+#else
+	/* PB31 */ { 1,   0,   0,   1,   0,   0,   0 }, /* pulseCatcherClr	*/
+#endif
 	/* PB30 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PB29 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PB28 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
@@ -85,19 +96,32 @@
 	/* PB26 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PB25 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PB24 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
+#if !defined(CONFIG_SC)
 	/* PB23 */ { 1,   0,   0,   0,   0,   0,   0 }, /* batteryOk		*/
+#else
+	/* PB23 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
+#endif
 	/* PB22 */ { 1,   0,   0,   0,   0,   0,   0 }, /* fpgaInitLowBi	*/
 	/* PB21 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PB20 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
+#if !defined(CONFIG_SC)
 	/* PB19 */ { 1,   0,   0,   1,   1,   1,   0 }, /* speakerVol		*/
+#else
+	/* PB19 */ { 0,   0,   0,   1,   1,   1,   0 }, /*	*/
+#endif
 	/* PB18 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
-	/* PB17 */ { 1,   0,   0,   1,   0,   0,   0 }, /* swBitOkLow		*/
+	/* PB17 */ { 1,   0,   0,   1,   0,   1,   0 }, /* swBitOkLow		*/
 	/* PB16 */ { 1,   0,   0,   0,   0,   0,   0 }, /* fpgaDone			*/
 	/* PB15 */ { 1,   0,   0,   1,   0,   0,   0 }, /* gpio1			*/
+#if !defined(CONFIG_SC)
 	/* PB14 */ { 1,   0,   0,   0,   0,   0,   0 }  /* docBusyLow		*/
-    },
+#else
+	/* PB14 */ { 0,   0,   0,   0,   0,   0,   0 }  /* 	*/
+#endif
+	},
 
 	/*
+	 * Port C configuration
 	 * Pin		Signal				Type	Active		Initial state
 	 * PC4		i2cBus1EnSig		Out		High		High
 	 * PC5		i2cBus2EnSig		Out		High		High
@@ -108,29 +132,48 @@
 	 * PC12		systemBitOkIn		In		High		X
 	 * PC15		selfDreqLow			In		Low			X
 	 */
-    {	/*	    conf ppar psor pdir podr pdat pint 	  function			*/
+	{	/*	    conf ppar psor pdir podr pdat pint 	  function			*/
 	/* N/A	*/ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* N/A	*/ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PC15 */ { 1,   0,   0,   0,   0,   0,   0 }, /* selfDreqLowIn	*/
 	/* PC14 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PC13 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
+#if !defined(CONFIG_SC)
 	/* PC12 */ { 1,   0,   0,   0,   0,   0,   0 }, /* systemBitOkIn	*/
+#else
+	/* PC12 */ { 0,   0,   0,   0,   0,   0,   0 }, /* 	*/
+#endif
 	/* PC11 */ { 1,   0,   0,   1,   0,   1,   0 }, /* fpgaResetLowOut	*/
+#if !defined(CONFIG_SC)
 	/* PC10 */ { 1,   0,   0,   1,   0,   1,   0 }, /* i2cBus4EnSig		*/
+#else
+	/* PC10 */ { 0,   0,   0,   1,   0,   1,   0 }, /*	*/
+#endif
 	/* PC9  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
+#if !defined(CONFIG_SC)
 	/* PC8  */ { 1,   0,   0,   1,   0,   1,   0 }, /* i2cBus3EnSig		*/
+#else
+	/* PC8  */ { 0,   0,   0,   1,   0,   1,   0 }, /*	*/
+#endif
 	/* PC7  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PC6  */ { 1,   0,   0,   1,   0,   1,   0 }, /* gpio0			*/
+#if !defined(CONFIG_SC)
 	/* PC5  */ { 1,   0,   0,   1,   0,   1,   0 }, /* i2cBus2EnSig		*/
 	/* PC4  */ { 1,   0,   0,   1,   0,   1,   0 }, /* i2cBus1EnSig		*/
+#else
+	/* PC5  */ { 0,   0,   0,   1,   0,   1,   0 }, /*	*/
+	/* PC4  */ { 0,   0,   0,   1,   0,   1,   0 }, /*	*/
+#endif
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }  /*	*/
-    },
+	},
 
-    /* Port D configuration */
-    {	/*	    conf ppar psor pdir podr pdat pint 	   function			*/
+	/*
+	 * Port D configuration
+	 */
+	{	/*	    conf ppar psor pdir podr pdat pint 	   function			*/
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* PD15 */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
@@ -149,7 +192,7 @@
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }, /*	*/
 	/* N/A  */ { 0,   0,   0,   0,   0,   0,   0 }  /*	*/
-    }
+	}
 };
 
 /*
diff --git a/board/gen860t/u-boot-flashenv.lds b/board/gen860t/u-boot-flashenv.lds
new file mode 100644
index 0000000..8b1ce1a
--- /dev/null
+++ b/board/gen860t/u-boot-flashenv.lds
@@ -0,0 +1,132 @@
+/*
+ * Linker command file for the GEN860T board when the environment is
+ * stored in flash memory.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+SECTIONS
+{
+  /*
+   * Read-only sections, merged into text segment:
+   */
+  . = + SIZEOF_HEADERS;
+  .interp        : { *(.interp)		}
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)	}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)	}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)	}
+  .rela.got      : { *(.rela.got)	}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)	}
+  .rela.bss      : { *(.rela.bss)	}
+  .rel.plt       : { *(.rel.plt)	}
+  .rela.plt      : { *(.rela.plt)	}
+  .init          : { *(.init)		}
+  .plt           : { *(.plt)		}
+  .text :
+  {
+    cpu/mpc8xx/start.o	(.text)
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /*
+   * Read-write section, merged into data segment:
+   */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data:
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+  
+  _end = . ;
+  PROVIDE (end = .);
+
+  .ppcenv:
+  {
+    . = env_offset;
+    common/environment.o
+  }
+}
diff --git a/board/gen860t/u-boot.lds b/board/gen860t/u-boot.lds
index 1b53c72..b67faa6 100644
--- a/board/gen860t/u-boot.lds
+++ b/board/gen860t/u-boot.lds
@@ -56,15 +56,6 @@
   .text :
   {
     cpu/mpc8xx/start.o		(.text)
-    common/dlmalloc.o		(.text)
-    lib_ppc/ppcstring.o		(.text)
-    lib_generic/vsprintf.o	(.text)
-    lib_generic/crc32.o		(.text)
-    lib_generic/zlib.o		(.text)
-
-/*    . = env_offset;
-    common/environment.o(.text) */
-
     *(.text)
     *(.fixup)
     *(.got1)
@@ -128,8 +119,6 @@
    *(.bss)
    *(COMMON)
   }
-
   _end = . ;
   PROVIDE (end = .);
 }
-
diff --git a/common/main.c b/common/main.c
index 33d8717..fe4ebb4 100644
--- a/common/main.c
+++ b/common/main.c
@@ -880,7 +880,7 @@
 			return 1;
 #else
 		if (parse_string_outer(arg,
-		    FLAG_PARSE_SEMICOLON | FLAG_EXIT_FROM_LOOP) == 0)
+		    FLAG_PARSE_SEMICOLON | FLAG_EXIT_FROM_LOOP) != 0)
 			return 1;
 #endif
 	}
diff --git a/cpu/mpc8260/Makefile b/cpu/mpc8260/Makefile
index 22d323e..81f74ec 100644
--- a/cpu/mpc8260/Makefile
+++ b/cpu/mpc8260/Makefile
@@ -28,7 +28,7 @@
 START	= start.o kgdb.o
 OBJS	= traps.o serial_smc.o serial_scc.o cpu.o cpu_init.o speed.o \
 	  interrupts.o ether_scc.o ether_fcc.o i2c.o commproc.o \
-	  bedbug_603e.o status_led.o pci.o
+	  bedbug_603e.o status_led.o pci.o spi.o
 
 all:	.depend $(START) $(LIB)
 
diff --git a/cpu/mpc8260/spi.c b/cpu/mpc8260/spi.c
new file mode 100644
index 0000000..6a2dc8f
--- /dev/null
+++ b/cpu/mpc8260/spi.c
@@ -0,0 +1,435 @@
+/*
+ * Copyright (c) 2001 Navin Boppuri / Prashant Patel
+ *	<nboppuri@trinetcommunication.com>,
+ *	<pmpatel@trinetcommunication.com>
+ * Copyright (c) 2001 Gerd Mennchen <Gerd.Mennchen@icn.siemens.de>
+ * Copyright (c) 2001-2003 Wolfgang Denk, DENX Software Engineering, <wd@denx.de>.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * MPC8260 CPM SPI interface.
+ *
+ * Parts of this code are probably not portable and/or specific to
+ * the board which I used for the tests. Please send fixes/complaints
+ * to wd@denx.de
+ *
+ */
+
+#include <common.h>
+#include <asm/cpm_8260.h>
+#include <linux/ctype.h>
+#include <malloc.h>
+#include <post.h>
+#include <net.h>
+
+#if defined(CONFIG_SPI)
+
+/* Warning:
+ * You cannot enable DEBUG for early system initalization, i. e. when
+ * this driver is used to read environment parameters like "baudrate"
+ * from EEPROM which are used to initialize the serial port which is
+ * needed to print the debug messages...
+ */
+#undef	DEBUG
+
+#define SPI_EEPROM_WREN		0x06
+#define SPI_EEPROM_RDSR		0x05
+#define SPI_EEPROM_READ		0x03
+#define SPI_EEPROM_WRITE	0x02
+
+/* ---------------------------------------------------------------
+ * Offset for initial SPI buffers in DPRAM:
+ * We need a 520 byte scratch DPRAM area to use at an early stage.
+ * It is used between the two initialization calls (spi_init_f()
+ * and spi_init_r()).
+ * The value 0x2000 makes it far enough from the start of the data
+ * area (as well as from the stack pointer).
+ * --------------------------------------------------------------- */
+#ifndef	CFG_SPI_INIT_OFFSET
+#define	CFG_SPI_INIT_OFFSET	0x2000
+#endif
+
+#define CPM_SPI_BASE 0x100
+
+#ifdef	DEBUG
+
+#define	DPRINT(a)	printf a;
+/* -----------------------------------------------
+ * Helper functions to peek into tx and rx buffers
+ * ----------------------------------------------- */
+static const char * const hex_digit = "0123456789ABCDEF";
+
+static char quickhex (int i)
+{
+	return hex_digit[i];
+}
+
+static void memdump (void *pv, int num)
+{
+	int i;
+	unsigned char *pc = (unsigned char *) pv;
+
+	for (i = 0; i < num; i++)
+		printf ("%c%c ", quickhex (pc[i] >> 4), quickhex (pc[i] & 0x0f));
+	printf ("\t");
+	for (i = 0; i < num; i++)
+		printf ("%c", isprint (pc[i]) ? pc[i] : '.');
+	printf ("\n");
+}
+#else	/* !DEBUG */
+
+#define	DPRINT(a)
+
+#endif	/* DEBUG */
+
+/* -------------------
+ * Function prototypes
+ * ------------------- */
+void spi_init (void);
+
+ssize_t spi_read (uchar *, int, uchar *, int);
+ssize_t spi_write (uchar *, int, uchar *, int);
+ssize_t spi_xfer (size_t);
+
+/* -------------------
+ * Variables
+ * ------------------- */
+
+#define MAX_BUFFER	0x104
+
+/* ----------------------------------------------------------------------
+ * Initially we place the RX and TX buffers at a fixed location in DPRAM!
+ * ---------------------------------------------------------------------- */
+static uchar *rxbuf =
+  (uchar *)&((immap_t *)CFG_IMMR)->im_dprambase
+			[CFG_SPI_INIT_OFFSET];
+static uchar *txbuf =
+  (uchar *)&((immap_t *)CFG_IMMR)->im_dprambase
+			[CFG_SPI_INIT_OFFSET+MAX_BUFFER];
+
+/* **************************************************************************
+ *
+ *  Function:    spi_init_f
+ *
+ *  Description: Init SPI-Controller (ROM part)
+ *
+ *  return:      ---
+ *
+ * *********************************************************************** */
+void spi_init_f (void)
+{
+	unsigned int dpaddr;
+
+	volatile spi_t *spi;
+	volatile immap_t *immr;
+	volatile cpm8260_t *cp;
+	volatile cbd_t *tbdf, *rbdf;
+
+	immr = (immap_t *)  CFG_IMMR;
+	cp   = (cpm8260_t *) &immr->im_cpm;
+
+	*(ushort *)(&immr->im_dprambase[PROFF_SPI_BASE]) = PROFF_SPI;
+	spi  = (spi_t *)&immr->im_dprambase[PROFF_SPI];
+
+/* 1 */
+	/* ------------------------------------------------
+	 * Initialize Port D SPI pins
+	 * (we are only in Master Mode !)
+	 * ------------------------------------------------ */
+
+	/* --------------------------------------------
+	 * GPIO or per. Function
+	 * PPARD[16] = 1 [0x00008000] (SPIMISO)
+	 * PPARD[17] = 1 [0x00004000] (SPIMOSI)
+	 * PPARD[18] = 1 [0x00002000] (SPICLK)
+	 * PPARD[12] = 0 [0x00080000] -> GPIO: (CS for ATC EEPROM)
+	 * -------------------------------------------- */
+	immr->im_ioport.iop_ppard |=  0x0000E000;	/* set  bits	*/
+	immr->im_ioport.iop_ppard &= ~0x00080000;	/* reset bit	*/
+
+	/* ----------------------------------------------
+	 * In/Out or per. Function 0/1
+	 * PDIRD[16] = 0 [0x00008000] -> PERI1: SPIMISO
+	 * PDIRD[17] = 0 [0x00004000] -> PERI1: SPIMOSI
+	 * PDIRD[18] = 0 [0x00002000] -> PERI1: SPICLK
+	 * PDIRD[12] = 1 [0x00080000] -> GPIO OUT: CS for ATC EEPROM
+	 * ---------------------------------------------- */
+	immr->im_ioport.iop_pdird &= ~0x0000E000;
+	immr->im_ioport.iop_pdird |= 0x00080000;
+
+	/* ----------------------------------------------
+	 * special option reg.
+	 * PSORD[16] = 1 [0x00008000] -> SPIMISO
+	 * PSORD[17] = 1 [0x00004000] -> SPIMOSI
+	 * PSORD[18] = 1 [0x00002000] -> SPICLK
+	 * ---------------------------------------------- */
+	immr->im_ioport.iop_psord |= 0x0000E000;
+
+	/* Initialize the parameter ram.
+	 * We need to make sure many things are initialized to zero
+	 */
+	spi->spi_rstate	= 0;
+	spi->spi_rdp	= 0;
+	spi->spi_rbptr	= 0;
+	spi->spi_rbc	= 0;
+	spi->spi_rxtmp	= 0;
+	spi->spi_tstate	= 0;
+	spi->spi_tdp	= 0;
+	spi->spi_tbptr	= 0;
+	spi->spi_tbc	= 0;
+	spi->spi_txtmp	= 0;
+
+	/* Allocate space for one transmit and one receive buffer
+	 * descriptor in the DP ram
+	 */
+#ifdef CFG_ALLOC_DPRAM
+	dpaddr = m8260_cpm_dpalloc (sizeof(cbd_t)*2, 8);
+#else
+	dpaddr = CPM_SPI_BASE;
+#endif
+
+/* 3 */
+	/* Set up the SPI parameters in the parameter ram */
+	spi->spi_rbase = dpaddr;
+	spi->spi_tbase = dpaddr + sizeof (cbd_t);
+
+	/***********IMPORTANT******************/
+
+        /*
+         * Setting transmit and receive buffer descriptor pointers
+         * initially to rbase and tbase. Only the microcode patches
+         * documentation talks about initializing this pointer. This
+         * is missing from the sample I2C driver. If you dont
+         * initialize these pointers, the kernel hangs.
+	 */
+	spi->spi_rbptr = spi->spi_rbase;
+	spi->spi_tbptr = spi->spi_tbase;
+
+/* 4 */
+	/* Init SPI Tx + Rx Parameters */
+	while (cp->cp_cpcr & CPM_CR_FLG)
+		;
+	cp->cp_cpcr = mk_cr_cmd(CPM_CR_SPI_PAGE, CPM_CR_SPI_SBLOCK,
+							0, CPM_CR_INIT_TRX) | CPM_CR_FLG;
+	while (cp->cp_cpcr & CPM_CR_FLG)
+		;
+
+/* 6 */
+	/* Set to big endian. */
+	spi->spi_tfcr = CPMFCR_EB;
+	spi->spi_rfcr = CPMFCR_EB;
+
+/* 7 */
+	/* Set maximum receive size. */
+	spi->spi_mrblr = MAX_BUFFER;
+
+/* 8 + 9 */
+	/* tx and rx buffer descriptors */
+	tbdf = (cbd_t *) & immr->im_dprambase[spi->spi_tbase];
+	rbdf = (cbd_t *) & immr->im_dprambase[spi->spi_rbase];
+
+	tbdf->cbd_sc &= ~BD_SC_READY;
+	rbdf->cbd_sc &= ~BD_SC_EMPTY;
+
+	/* Set the bd's rx and tx buffer address pointers */
+	rbdf->cbd_bufaddr = (ulong) rxbuf;
+	tbdf->cbd_bufaddr = (ulong) txbuf;
+
+/* 10 + 11 */
+	immr->im_spi.spi_spie = SPI_EMASK;		/* Clear all SPI events	*/
+	immr->im_spi.spi_spim = 0x00;			/* Mask  all SPI events */
+
+
+	return;
+}
+
+/* **************************************************************************
+ *
+ *  Function:    spi_init_r
+ *
+ *  Description: Init SPI-Controller (RAM part) -
+ *		 The malloc engine is ready and we can move our buffers to
+ *		 normal RAM
+ *
+ *  return:      ---
+ *
+ * *********************************************************************** */
+void spi_init_r (void)
+{
+	volatile spi_t *spi;
+	volatile immap_t *immr;
+	volatile cpm8260_t *cp;
+	volatile cbd_t *tbdf, *rbdf;
+
+	immr = (immap_t *)  CFG_IMMR;
+	cp   = (cpm8260_t *) &immr->im_cpm;
+
+	spi  = (spi_t *)&immr->im_dprambase[PROFF_SPI];
+
+	/* tx and rx buffer descriptors */
+	tbdf = (cbd_t *) & immr->im_dprambase[spi->spi_tbase];
+	rbdf = (cbd_t *) & immr->im_dprambase[spi->spi_rbase];
+
+	/* Allocate memory for RX and TX buffers */
+	rxbuf = (uchar *) malloc (MAX_BUFFER);
+	txbuf = (uchar *) malloc (MAX_BUFFER);
+
+	rbdf->cbd_bufaddr = (ulong) rxbuf;
+	tbdf->cbd_bufaddr = (ulong) txbuf;
+
+	return;
+}
+
+/****************************************************************************
+ *  Function:    spi_write
+ **************************************************************************** */
+ssize_t spi_write (uchar *addr, int alen, uchar *buffer, int len)
+{
+	int i;
+
+	memset(rxbuf, 0, MAX_BUFFER);
+	memset(txbuf, 0, MAX_BUFFER);
+	*txbuf = SPI_EEPROM_WREN;		/* write enable		*/
+	spi_xfer(1);
+	memcpy(txbuf, addr, alen);
+	*txbuf = SPI_EEPROM_WRITE;		/* WRITE memory array	*/
+	memcpy(alen + txbuf, buffer, len);
+	spi_xfer(alen + len);
+						/* ignore received data	*/
+	for (i = 0; i < 1000; i++) {
+		*txbuf = SPI_EEPROM_RDSR;	/* read status		*/
+		txbuf[1] = 0;
+		spi_xfer(2);
+		if (!(rxbuf[1] & 1)) {
+			break;
+		}
+		udelay(1000);
+	}
+	if (i >= 1000) {
+		printf ("*** spi_write: Time out while writing!\n");
+	}
+
+	return len;
+}
+
+/****************************************************************************
+ *  Function:    spi_read
+ **************************************************************************** */
+ssize_t spi_read (uchar *addr, int alen, uchar *buffer, int len)
+{
+	memset(rxbuf, 0, MAX_BUFFER);
+	memset(txbuf, 0, MAX_BUFFER);
+	memcpy(txbuf, addr, alen);
+	*txbuf = SPI_EEPROM_READ;		/* READ memory array	*/
+
+	/*
+	 * There is a bug in 860T (?) that cuts the last byte of input
+	 * if we're reading into DPRAM. The solution we choose here is
+	 * to always read len+1 bytes (we have one extra byte at the
+	 * end of the buffer).
+	 */
+	spi_xfer(alen + len + 1);
+	memcpy(buffer, alen + rxbuf, len);
+
+	return len;
+}
+
+/****************************************************************************
+ *  Function:    spi_xfer
+ **************************************************************************** */
+ssize_t spi_xfer (size_t count)
+{
+	volatile immap_t *immr;
+	volatile cpm8260_t *cp;
+	volatile spi_t *spi;
+	cbd_t *tbdf, *rbdf;
+	int tm;
+
+	DPRINT (("*** spi_xfer entered ***\n"));
+
+	immr = (immap_t *) CFG_IMMR;
+	cp   = (cpm8260_t *) &immr->im_cpm;
+
+	spi  = (spi_t *)&immr->im_dprambase[PROFF_SPI];
+
+	tbdf = (cbd_t *) & immr->im_dprambase[spi->spi_tbase];
+	rbdf = (cbd_t *) & immr->im_dprambase[spi->spi_rbase];
+
+	/* Board-specific: Set CS for device (ATC EEPROM) */
+	immr->im_ioport.iop_pdatd &= ~0x00080000;
+
+	/* Setting tx bd status and data length */
+	tbdf->cbd_sc  = BD_SC_READY | BD_SC_LAST | BD_SC_WRAP;
+	tbdf->cbd_datlen = count;
+
+	DPRINT (("*** spi_xfer: Bytes to be xferred: %d ***\n",
+							tbdf->cbd_datlen));
+
+	/* Setting rx bd status and data length */
+	rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP;
+	rbdf->cbd_datlen = 0;	 /* rx length has no significance */
+
+	immr->im_spi.spi_spmode = SPMODE_REV	|
+			SPMODE_MSTR	|
+			SPMODE_EN	|
+			SPMODE_LEN(8)	|	/* 8 Bits per char */
+			SPMODE_PM(0x8) ;	/* medium speed */
+	immr->im_spi.spi_spie = SPI_EMASK;		/* Clear all SPI events	*/
+	immr->im_spi.spi_spim = 0x00;			/* Mask  all SPI events */
+
+	/* start spi transfer */
+	DPRINT (("*** spi_xfer: Performing transfer ...\n"));
+	immr->im_spi.spi_spcom |= SPI_STR;		/* Start transmit */
+
+	/* --------------------------------
+	 * Wait for SPI transmit to get out
+	 * or time out (1 second = 1000 ms)
+	 * -------------------------------- */
+	for (tm=0; tm<1000; ++tm) {
+		if (immr->im_spi.spi_spie & SPI_TXB) {	/* Tx Buffer Empty */
+			DPRINT (("*** spi_xfer: Tx buffer empty\n"));
+			break;
+		}
+		if ((tbdf->cbd_sc & BD_SC_READY) == 0) {
+			DPRINT (("*** spi_xfer: Tx BD done\n"));
+			break;
+		}
+		udelay (1000);
+	}
+	if (tm >= 1000) {
+		printf ("*** spi_xfer: Time out while xferring to/from SPI!\n");
+	}
+	DPRINT (("*** spi_xfer: ... transfer ended\n"));
+
+#ifdef	DEBUG
+	printf ("\nspi_xfer: txbuf after xfer\n");
+	memdump ((void *) txbuf, 16);	/* dump of txbuf before transmit */
+	printf ("spi_xfer: rxbuf after xfer\n");
+	memdump ((void *) rxbuf, 16);	/* dump of rxbuf after transmit */
+	printf ("\n");
+#endif
+
+	/* Clear CS for device */
+	immr->im_ioport.iop_pdatd |= 0x00080000;
+
+	return count;
+}
+#endif	/* CONFIG_SPI */
diff --git a/cpu/mpc8xx/lcd.c b/cpu/mpc8xx/lcd.c
index 3d3b039..0db5348 100644
--- a/cpu/mpc8xx/lcd.c
+++ b/cpu/mpc8xx/lcd.c
@@ -27,6 +27,7 @@
 
 #include <config.h>
 #include <common.h>
+#include <watchdog.h>
 #include <version.h>
 #include <stdarg.h>
 #include <lcdvideo.h>
@@ -1059,6 +1060,8 @@
 	/* Leave room for default color map */
 	cmap = (ushort *)&(cp->lcd_cmap[BMP_LOGO_OFFSET*sizeof(ushort)]);
 
+	WATCHDOG_RESET();
+
 	/* Set color map */
 	for (i=0; i<(sizeof(bmp_logo_palette)/(sizeof(ushort))); ++i) {
 		ushort colreg = bmp_logo_palette[i];
@@ -1071,11 +1074,15 @@
 	bmap = &bmp_logo_bitmap[0];
 	fb   = (char *)(lcd_base + y * lcd_line_length + x);
 
+	WATCHDOG_RESET();
+
 	for (i=0; i<BMP_LOGO_HEIGHT; ++i) {
 		memcpy (fb, bmap, BMP_LOGO_WIDTH);
 		bmap += BMP_LOGO_WIDTH;
 		fb   += panel_info.vl_col;
 	}
+
+	WATCHDOG_RESET();
 }
 #endif /* CONFIG_LCD_LOGO */
 
@@ -1098,6 +1105,8 @@
 	unsigned colors,bpix;
 	unsigned long compression;
 
+	WATCHDOG_RESET();
+
 	if (!((bmp->header.signature[0]=='B') &&
 	      (bmp->header.signature[1]=='M'))) {
 		printf ("Error: no valid bmp image at %lx\n", bmp_image);
@@ -1149,6 +1158,8 @@
 #endif
 			*cmap-- = colreg;
 		}
+
+		WATCHDOG_RESET();
 	}
 
 	padded_line = (width&0x3) ? ((width&~0x3)+4) : (width);
@@ -1163,6 +1174,7 @@
 		 (((height>=panel_info.vl_row) ? panel_info.vl_row : height)-1)
 		 * lcd_line_length);
 	for (i = 0; i < height; ++i) {
+		WATCHDOG_RESET();
 		for (j = 0; j < width ; j++)
 			*(fb++)=255-*(bmap++);
 		bmap += (width - padded_line);
diff --git a/include/asm-ppc/cpm_8260.h b/include/asm-ppc/cpm_8260.h
index bf2e2a2..5c70603 100644
--- a/include/asm-ppc/cpm_8260.h
+++ b/include/asm-ppc/cpm_8260.h
@@ -170,7 +170,7 @@
  */
 #define PROFF_SMC1	(0)
 #define PROFF_SMC2	(64)
-
+#define PROFF_SPI	((16*1024) - 128)
 
 /* Define enough so I can at least use the serial port as a UART.
  */
@@ -737,6 +737,17 @@
 #define SPMODE_LEN(x)	((((x)-1)&0xF)<<4)
 #define SPMODE_PM(x)	((x) &0xF)
 
+/* SPI Event/Mask register.
+*/
+#define SPI_EMASK		0x37	/* Event Mask				*/
+#define SPI_MME			0x20	/* Multi-Master Error			*/
+#define SPI_TXE			0x10	/* Transmit Error			*/
+#define SPI_BSY			0x04	/* Busy					*/
+#define SPI_TXB			0x02	/* Tx Buffer Empty			*/
+#define SPI_RXB			0x01	/* RX Buffer full/closed		*/
+
+#define SPI_STR			0x80	/* SPCOM: Start transmit		*/
+
 #define SPI_EB		((u_char)0x10)		/* big endian byte order */
 
 #define BD_IIC_START		((ushort)0x0400)
diff --git a/include/common.h b/include/common.h
index 5096754..2ff1c8c 100644
--- a/include/common.h
+++ b/include/common.h
@@ -198,7 +198,7 @@
 # define CFG_DEF_EEPROM_ADDR CFG_I2C_EEPROM_ADDR
 #endif /* CONFIG_SPI || !defined(CFG_I2C_EEPROM_ADDR) */
 
-#if defined(CONFIG_PCU_E) || defined(CONFIG_CCM)
+#if defined(CONFIG_PCU_E) || defined(CONFIG_CCM) || defined(CONFIG_ATC)
 extern void spi_init_f (void);
 extern void spi_init_r (void);
 extern ssize_t spi_read  (uchar *, int, uchar *, int);
diff --git a/include/configs/GEN860T.h b/include/configs/GEN860T.h
index 29e4807..47a8786 100644
--- a/include/configs/GEN860T.h
+++ b/include/configs/GEN860T.h
@@ -38,14 +38,22 @@
 /*
  * Identify the board
  */
-#define CONFIG_IDENT_STRING				" GEN860T"
+#if !defined(CONFIG_SC)
+#define CONFIG_IDENT_STRING				" B2"
+#else
+#define CONFIG_IDENT_STRING				" SC"
+#endif
 
 /*
  * Don't depend on the RTC clock to determine clock frequency -
  * the 860's internal rtc uses a 32.768 KHz clock which is
  * generated by the DS1337 - and the DS1337 clock can be turned off.
  */
-#define	CONFIG_8xx_GCLK_FREQ			66600000
+#if !defined(CONFIG_SC)
+#define	CONFIG_8xx_GCLK_FREQ			66600000 
+#else
+#define	CONFIG_8xx_GCLK_FREQ			48000000
+#endif
 
 /*
  * The RS-232 console port is on SMC1
@@ -143,7 +151,7 @@
  * environment so that we can autoscript the full default environment.
  */
 #define CONFIG_ETHADDR					9a:52:63:15:85:25
-#define CONFIG_SERVERIP					10.0.4.200
+#define CONFIG_SERVERIP					10.0.4.201
 #define CONFIG_IPADDR					10.0.4.111
 
 /*
@@ -156,17 +164,20 @@
 #define	CFG_I2C_EEPROM_ADDR_LEN			2		/* need 16 bit address	*/
 #define CFG_ENV_EEPROM_SIZE				(32 * 1024)
 
-#undef	CONFIG_HARD_I2C
-#define CONFIG_SOFT_I2C
-
 /*
- * Configure software I2C support (taken from IP860 BSP).
- * The I2C bus is connected to the GEN860T's 'dedicated' I2C
- * pins, i.e. PB26 and PB27
+ * Enable I2C and select the hardware/software driver
  */
+#define CONFIG_HARD_I2C		1				/* CPM based I2C			*/
+#undef	CONFIG_SOFT_I2C        				/* Bit-banged I2C			*/
+
+#ifdef CONFIG_HARD_I2C
+#define	CFG_I2C_SPEED		100000			/* clock speed in Hz		*/
+#define CFG_I2C_SLAVE		0xFE			/* I2C slave address		*/
+#endif
+
+#ifdef CONFIG_SOFT_I2C
 #define PB_SCL				0x00000020		/* PB 26					*/
 #define PB_SDA				0x00000010		/* PB 27 					*/
-
 #define I2C_INIT			(immr->im_cpm.cp_pbdir |=  PB_SCL)
 #define I2C_ACTIVE			(immr->im_cpm.cp_pbdir |=  PB_SDA)
 #define I2C_TRISTATE		(immr->im_cpm.cp_pbdir &= ~PB_SDA)
@@ -176,15 +187,14 @@
 #define I2C_SCL(bit)		if(bit) immr->im_cpm.cp_pbdat |=  PB_SCL; \
 								else    immr->im_cpm.cp_pbdat &= ~PB_SCL
 #define I2C_DELAY			udelay(5)		/* 1/4 I2C clock duration	*/
-
-#define	CFG_I2C_SPEED		100000			/* clock speed in Hz		*/
-#define CFG_I2C_SLAVE		0xFE			/* I2C slave address		*/
+#endif
 
 /*
  * Allow environment overwrites by anyone
  */
 #define CONFIG_ENV_OVERWRITE
 
+#if !defined(CONFIG_SC)
 /*
  * The MPC860's internal RTC is horribly broken in rev D masks. Three
  * internal MPC860T circuit nodes were inadvertently left floating; this
@@ -193,35 +203,55 @@
  * reasonable battery can keep that kind RTC running during powerdown for any
  * length of time, so we use an external RTC on the I2C bus instead.
  */
-#undef	CONFIG_RTC_MPC8xx
 #define CONFIG_RTC_DS1337
-#define CFG_I2C_RTC_ADDR				0x68
+#define CFG_I2C_RTC_ADDR				0x68 
 
+#else
 /*
- * Allow partial commands to be matched to uniqueness.
+ * No external RTC on SC variant, so we're stuck with the internal one.
  */
-#define CFG_MATCH_PARTIAL_CMD
+#define	CONFIG_RTC_MPC8xx
+#endif
+
+/*
+ * Power On Self Test support
+ */
+#define CONFIG_POST			  ( CFG_POST_CACHE		| \
+								CFG_POST_MEMORY		| \
+								CFG_POST_CPU		| \
+								CFG_POST_UART		| \
+								CFG_POST_SPR )
+
+#ifdef CONFIG_POST
+#define CFG_CMD_POST_DIAG CFG_CMD_DIAG
+#else
+#define CFG_CMD_POST_DIAG		0
+#endif
 
 /*
  * List of available monitor commands.  Use the system default list
  * plus add some of the "non-standard" commands back in.
  * See ./cmd_confdefs.h
  */
-#define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
+#define BASE_CONFIG_COMMANDS	( CONFIG_CMD_DFL	| \
 								CFG_CMD_ASKENV	| \
 								CFG_CMD_DHCP	| \
 								CFG_CMD_I2C		| \
-								CFG_CMD_DOC		| \
 								CFG_CMD_EEPROM	| \
 								CFG_CMD_REGINFO	| \
 								CFG_CMD_IMMAP	| \
 								CFG_CMD_ELF		| \
 								CFG_CMD_DATE	| \
-								CFG_CMD_DATE	| \
 								CFG_CMD_FPGA	| \
 								CFG_CMD_MII 	| \
-								CFG_CMD_BEDBUG	\
-						      )
+								CFG_CMD_BEDBUG	| \
+								CFG_CMD_POST_DIAG )
+
+#if !defined(CONFIG_SC)
+#define	CONFIG_COMMANDS ( BASE_CONFIG_COMMANDS | CFG_CMD_DOC ) 
+#else
+#define CONFIG_COMMANDS	BASE_CONFIG_COMMANDS
+#endif
 
 /*
  * There is no IDE/PCMCIA hardware support on the board.
@@ -258,7 +288,12 @@
  * Verbose help from command monitor.
  */
 #define	CFG_LONGHELP
-#define	CFG_PROMPT			"gen860t> "
+#if !defined(CONFIG_SC)
+#define	CFG_PROMPT			"B2> "
+#else
+#define	CFG_PROMPT			"SC> "
+#endif
+
 
 /*
  * Use the "hush" command parser
@@ -393,15 +428,9 @@
 /*
  * Reserve memory for U-Boot.
  */
-#define CFG_MAX_U_BOOT_SECT	3
-
-#if defined(DEBUG)
-#define	CFG_MONITOR_LEN		(512 * 1024)
-#else
-#define	CFG_MONITOR_LEN		(256 * 1024)
-#endif
-
-#define CFG_MONITOR_BASE	CFG_FLASH_BASE
+#define CFG_MAX_UBOOT_SECTS		4
+#define	CFG_MONITOR_LEN			(CFG_MAX_UBOOT_SECTS * CFG_FLASH_SECT_SIZE)
+#define CFG_MONITOR_BASE		CFG_FLASH_BASE
 
 /*
  * Select environment placement.  NOTE that u-boot.lds must
@@ -414,8 +443,14 @@
 #define CFG_ENV_SIZE			(2 * 1024)
 #define CFG_ENV_OFFSET			(CFG_ENV_EEPROM_SIZE - (8 * 1024))
 #else
-#define CFG_ENV_SIZE			(4 * 1024)
-#define CFG_ENV_OFFSET			(CFG_MAX_U_BOOT_SECT * CFG_FLASH_SECT_SIZE)
+#define CFG_ENV_SIZE			0x1000
+#define CFG_ENV_SECT_SIZE		CFG_FLASH_SECT_SIZE
+
+/*
+ * This ultimately gets passed right into the linker script, so we have to
+ * use a number :(
+ */
+#define CFG_ENV_OFFSET			0x060000
 #endif
 
 /*
@@ -439,7 +474,7 @@
 #endif
 
 /*------------------------------------------------------------------------
- * SYPCR - System Protection Control				UM 11-9
+ * SYPCR - System Protection Control							UM 11-9
  * -----------------------------------------------------------------------
  * SYPCR can only be written once after reset!
  *
@@ -523,6 +558,7 @@
  */
 #define SCCR_MASK   SCCR_EBDF11
 
+#if !defined(CONFIG_SC)
 #define CFG_SCCR	( SCCR_TBS			| 	/* timebase = GCLK/2	*/ \
 					  SCCR_COM00   		| 	/* full strength CLKOUT	*/ \
 					  SCCR_DFSYNC00 	| 	/* SYNCLK / 1 (normal)	*/ \
@@ -530,6 +566,17 @@
 					  SCCR_DFNL000		| \
 					  SCCR_DFNH000		  \
 					)
+#else
+#define CFG_SCCR	( SCCR_TBS			| 	/* timebase = GCLK/2	*/ \
+					  SCCR_COM00   		| 	/* full strength CLKOUT	*/ \
+					  SCCR_DFSYNC00 	| 	/* SYNCLK / 1 (normal)	*/ \
+					  SCCR_DFBRG00		| 	/* BRGCLK / 1 (normal)	*/ \
+					  SCCR_DFNL000		| \
+					  SCCR_DFNH000		| \
+					  SCCR_RTDIV		| \
+					  SCCR_RTSEL		  \
+					)
+#endif
 
 /*-----------------------------------------------------------------------
  * DER - Debug Enable Register									UM 37-46
@@ -695,10 +742,12 @@
 /*
  * Disk On Chip (millenium) configuration
  */
+#if !defined(CONFIG_SC)
 #define CFG_MAX_DOC_DEVICE	1
 #undef	CFG_DOC_SUPPORT_2000
 #define CFG_DOC_SUPPORT_MILLENNIUM
 #undef	CFG_DOC_PASSIVE_PROBE
+#endif
 
 /*
  * FEC interrupt assignment
diff --git a/include/configs/TQM8260.h b/include/configs/TQM8260.h
index 86281dd..1ea9a5e 100644
--- a/include/configs/TQM8260.h
+++ b/include/configs/TQM8260.h
@@ -203,11 +203,15 @@
 
 
 /* system clock rate (CLKIN) - equal to the 60x and local bus speed */
-#ifndef CONFIG_300MHz
-#define CONFIG_8260_CLKIN	66666666	/* in Hz */
-#else
-#define CONFIG_8260_CLKIN	83333000	/* in Hz */
-#endif
+#ifdef CONFIG_MPC8255
+#  define CONFIG_8260_CLKIN	66666666	/* in Hz */
+#else	/* !CONFIG_MPC8255 */
+# ifndef CONFIG_300MHz
+#  define CONFIG_8260_CLKIN	66666666	/* in Hz */
+# else
+#  define CONFIG_8260_CLKIN	83333000	/* in Hz */
+# endif
+#endif	/* CONFIG_MPC8255 */
 
 #if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
 #define CONFIG_BAUDRATE		230400
@@ -311,15 +315,19 @@
  * defines for the various registers affected by the HRCW e.g. changing
  * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
  */
-#if defined(CONFIG_266MHz)
-#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
-				 HRCW_MODCK_H0111)
-#elif defined(CONFIG_300MHz)
-#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS | \
-				 HRCW_MODCK_H0110)
-#else
-#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
-#endif
+#define	__HRCW__ALL__		(HRCW_CIP | HRCW_ISB111 | HRCW_BMS)
+
+#ifdef	CONFIG_MPC8255
+#  define CFG_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0111)
+#else	/* ! MPC8255 */
+# if defined(CONFIG_266MHz)
+#  define CFG_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0111)
+# elif defined(CONFIG_300MHz)
+#  define CFG_HRCW_MASTER	(__HRCW__ALL__ | HRCW_MODCK_H0110)
+# else
+#  define CFG_HRCW_MASTER	(__HRCW__ALL__)
+# endif
+#endif	/* CONFIG_MPC8255 */
 
 /* no slaves so just fill with zeros */
 #define CFG_HRCW_SLAVE1		0
diff --git a/include/configs/atc.h b/include/configs/atc.h
new file mode 100644
index 0000000..ca6b740
--- /dev/null
+++ b/include/configs/atc.h
@@ -0,0 +1,442 @@
+/*
+ * (C) Copyright 2001
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU		*/
+#define CONFIG_ATC		1	/* ...on a ATC board	*/
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define  CONFIG_CONS_ON_SMC		/* define if console on SMC */
+#undef CONFIG_CONS_ON_SCC		/* define if console on SCC */
+#undef  CONFIG_CONS_NONE		/* define if console on something else*/
+#define CONFIG_CONS_INDEX	2	/* which serial channel for console */
+
+#define CONFIG_BAUDRATE		115200
+
+/*
+ * select ethernet configuration
+ *
+ * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
+ * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
+ * for FCC)
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ *
+ */
+#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC       */
+#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
+#define CONFIG_ETHER_ON_FCC
+
+#define	CONFIG_NET_MULTI
+#define CONFIG_ETHER_ON_FCC2
+
+/*
+ * - Rx-CLK is CLK13
+ * - Tx-CLK is CLK14
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK2	(CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+# define CFG_CPMFCR_RAMTYPE	0
+# define CFG_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+#define CONFIG_ETHER_ON_FCC3
+
+/*
+ * - Rx-CLK is CLK15
+ * - Tx-CLK is CLK16
+ * - RAM for BD/Buffers is on the local Bus (see 28-13)
+ * - Enable Half Duplex in FSMR
+ */
+# define CFG_CMXFCR_MASK3	(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
+# define CFG_CMXFCR_VALUE3	(CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#define CONFIG_8260_CLKIN	64000000	/* in Hz */
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#undef	CONFIG_CLOCKS_IN_MHZ		/* clocks passsed to Linux in Hz */
+
+#define CONFIG_PREBOOT							\
+	"echo;"								\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;"\
+	"echo"
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND						\
+	"bootp;"							\
+	"setenv bootargs root=/dev/nfs rw "				\
+	"nfsroot=$(serverip):$(rootpath) " 				\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"\
+	"bootm"
+
+/*-----------------------------------------------------------------------
+ * Miscellaneous configuration options
+ */
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | CFG_CMD_EEPROM)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Miscellaneous configurable options
+ */
+#define	CFG_LONGHELP			/* undef to save memory		*/
+#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define	CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END	0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define	CFG_LOAD_ADDR	0x100000	/* default load address	*/
+
+#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define	CFG_RESET_ADDRESS 0xFFF00100	/* "bad" address		*/
+
+#define CFG_ALLOC_DPRAM
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_SPI
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Flash configuration
+ */
+
+#define CFG_BOOTROM_BASE	0xFF800000
+#define CFG_BOOTROM_SIZE	0x00080000
+#define CFG_FLASH_BASE		0xFF000000
+#define CFG_FLASH_SIZE		0x00800000
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max num of memory banks      */
+#define CFG_MAX_FLASH_SECT	128	/* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
+
+#define CONFIG_FLASH_16BIT
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB100 | HRCW_BMS | \
+				 HRCW_BPS10 | HRCW_DPPC10 |\
+				 HRCW_APPC10)
+
+/* no slaves so just fill with zeros */
+#define CFG_HRCW_SLAVE1		0
+#define CFG_HRCW_SLAVE2		0
+#define CFG_HRCW_SLAVE3		0
+#define CFG_HRCW_SLAVE4		0
+#define CFG_HRCW_SLAVE5		0
+#define CFG_HRCW_SLAVE6		0
+#define CFG_HRCW_SLAVE7		0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define CFG_INIT_RAM_END	0x2F00  /* End of used area in DPRAM    */
+#define CFG_GBL_DATA_SIZE	128 /* size in bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ *
+ * 60x SDRAM is mapped at CFG_SDRAM_BASE.
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_MAX_SIZE	0x08000000	/* max. 128 MB		*/
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+# define CFG_RAMBOOT
+#endif
+
+#if 1
+/* environment is in Flash */
+#define CFG_ENV_IS_IN_FLASH	1
+# define CFG_ENV_ADDR		(CFG_FLASH_BASE+0x40000)
+# define CFG_ENV_SIZE		0x10000
+# define CFG_ENV_SECT_SIZE	0x10000
+#else
+#define CFG_ENV_IS_IN_EEPROM	1
+#define CFG_ENV_OFFSET		0
+#define CFG_ENV_SIZE		2048
+#define CFG_EEPROM_PAGE_WRITE_BITS	4	/* 16-byte page size	*/
+#endif
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH*/
+#define BOOTFLAG_WARM		0x02	/* Software reboot                 */
+
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers                    2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT   (HID0_ICE|HID0_DCE|HID0_ICFI|\
+                         HID0_DCI|HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL  (HID0_IFEM|HID0_ABE)
+#define CFG_HID2        0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register                                     5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR         RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration                                       4-25
+ *-----------------------------------------------------------------------
+ */
+#define BCR_APD01	0x10000000
+#define CFG_BCR		(BCR_APD01|BCR_ETM|BCR_LETM)	/* 8260 mode */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration                             4-31
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SIUMCR      (SIUMCR_BBD|SIUMCR_DPPC10|SIUMCR_APPC10|\
+			 SIUMCR_CS10PC00|SIUMCR_BCTLC10)
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control                             4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+                         SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+                         SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control                     4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control                 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control                                   9-8
+ *-----------------------------------------------------------------------
+ * Ensure DFBRG is Divide by 16
+ */
+#define CFG_SCCR        SCCR_DFBRG01
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration                         13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR        0
+
+#define CFG_MIN_AM_MASK	0xC0000000
+/*-----------------------------------------------------------------------
+ * MPTPR - Memory Refresh Timer Prescaler Register              10-18
+ *-----------------------------------------------------------------------
+ */
+#define CFG_MPTPR       0x1F00
+
+/*-----------------------------------------------------------------------
+ * PSRT - Refresh Timer Register                                10-16
+ *-----------------------------------------------------------------------
+ */
+#define CFG_PSRT        0x0f
+
+/*-----------------------------------------------------------------------
+ * PSRT - SDRAM Mode Register                                   10-10
+ *-----------------------------------------------------------------------
+ */
+
+	/* SDRAM initialization values for 8-column chips
+	 */
+#define CFG_OR2_8COL	(CFG_MIN_AM_MASK		|\
+			 ORxS_BPD_4			|\
+			 ORxS_ROWST_PBI0_A10		|\
+			 ORxS_NUMR_11)
+
+#define CFG_PSDMR_8COL	(PSDMR_SDAM_A13_IS_A5		|\
+			 PSDMR_BSMA_A16_A18		|\
+			 PSDMR_SDA10_PBI0_A10		|\
+			 PSDMR_RFRC_7_CLK		|\
+			 PSDMR_PRETOACT_2W		|\
+			 PSDMR_ACTTORW_1W		|\
+			 PSDMR_LDOTOPRE_1C		|\
+			 PSDMR_WRC_1C			|\
+			 PSDMR_CL_2)
+
+	/* SDRAM initialization values for 9-column chips
+	 */
+#define CFG_OR2_9COL	(CFG_MIN_AM_MASK		|\
+			 ORxS_BPD_4			|\
+			 ORxS_ROWST_PBI0_A7		|\
+			 ORxS_NUMR_13)
+
+#define CFG_PSDMR_9COL	(PSDMR_SDAM_A14_IS_A5		|\
+			 PSDMR_BSMA_A13_A15		|\
+			 PSDMR_SDA10_PBI0_A9		|\
+			 PSDMR_RFRC_7_CLK		|\
+			 PSDMR_PRETOACT_2W		|\
+			 PSDMR_ACTTORW_1W		|\
+			 PSDMR_LDOTOPRE_1C		|\
+			 PSDMR_WRC_1C			|\
+			 PSDMR_CL_2)
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus     Machine PortSz  Device
+ * ---- ---     ------- ------  ------
+ *  0   60x     GPCM    8  bit  Boot ROM
+ *  1   60x     GPCM    64 bit  FLASH
+ *  2   60x     SDRAM   64 bit  SDRAM
+ *
+ */
+
+#define CFG_MRS_OFFS	0x00000000
+
+/* Bank 0 - FLASH
+ */
+#define CFG_BR0_PRELIM  ((CFG_FLASH_BASE & BRx_BA_MSK)  |\
+                         BRx_PS_16                      |\
+                         BRx_MS_GPCM_P                  |\
+                         BRx_V)
+
+#define CFG_OR0_PRELIM  (P2SZ_TO_AM(CFG_FLASH_SIZE)     |\
+                         ORxG_CSNT                      |\
+                         ORxG_ACS_DIV1                  |\
+                         ORxG_SCY_3_CLK                 |\
+                         ORxU_EHTR_8IDLE)
+
+
+/* Bank 2 - 60x bus SDRAM
+ */
+#ifndef CFG_RAMBOOT
+#define CFG_BR2_PRELIM  ((CFG_SDRAM_BASE & BRx_BA_MSK)  |\
+                         BRx_PS_64                      |\
+                         BRx_MS_SDRAM_P                 |\
+                         BRx_V)
+
+#define CFG_OR2_PRELIM	 CFG_OR2_8COL
+
+#define CFG_PSDMR	 CFG_PSDMR_8COL
+#endif /* CFG_RAMBOOT */
+
+#endif	/* __CONFIG_H */
diff --git a/include/status_led.h b/include/status_led.h
index 773573d..0d5a56e 100644
--- a/include/status_led.h
+++ b/include/status_led.h
@@ -97,20 +97,20 @@
 # define STATUS_LED_DAT			im_ioport.iop_padat
 
 # define STATUS_LED_BIT			0x0800	/* Red LED 0 is on PA.4	*/
-# define STATUS_LED_PERIOD		(CFG_HZ / 2)
-# define STATUS_LED_STATE		STATUS_LED_BLINKING
+# define STATUS_LED_PERIOD		(CFG_HZ / 4)
+# define STATUS_LED_STATE		STATUS_LED_OFF
 # define STATUS_LED_BIT1		0x0400	/* Grn LED 1 is on PA.5	*/
-# define STATUS_LED_PERIOD1		(CFG_HZ / 2)
+# define STATUS_LED_PERIOD1		(CFG_HZ / 8)
 # define STATUS_LED_STATE1		STATUS_LED_BLINKING
 # define STATUS_LED_BIT2		0x0080	/* Red LED 2 is on PA.8	*/
-# define STATUS_LED_PERIOD2		(CFG_HZ / 2)
-# define STATUS_LED_STATE2		STATUS_LED_BLINKING
+# define STATUS_LED_PERIOD2		(CFG_HZ / 4)
+# define STATUS_LED_STATE2		STATUS_LED_OFF
 # define STATUS_LED_BIT3		0x0040	/* Grn LED 3 is on PA.9	*/
-# define STATUS_LED_PERIOD3		(CFG_HZ / 2)
-# define STATUS_LED_STATE3		STATUS_LED_BLINKING
+# define STATUS_LED_PERIOD3		(CFG_HZ / 4)
+# define STATUS_LED_STATE3		STATUS_LED_OFF
 
 # define STATUS_LED_ACTIVE		1	/* LED on for bit == 1	*/
-# define STATUS_LED_BOOT		0	/* Boot status on LED 1	*/
+# define STATUS_LED_BOOT		1	/* Boot status on LED 1	*/
 
 /*****  IVMS8  **********************************************************/
 #elif defined(CONFIG_IVMS8)
diff --git a/lib_ppc/board.c b/lib_ppc/board.c
index 4b1edee..923f70e 100644
--- a/lib_ppc/board.c
+++ b/lib_ppc/board.c
@@ -50,8 +50,10 @@
 #include <cmd_bedbug.h>
 #endif
 #ifdef CFG_ALLOC_DPRAM
+#if !defined(CONFIG_8260)
 #include <commproc.h>
 #endif
+#endif
 #include <version.h>
 #if defined(CONFIG_BAB7xx)
 #include <w83c553f.h>
@@ -277,8 +279,10 @@
 	get_clocks,		/* get CPU and bus clocks (etc.) */
 	init_timebase,
 #ifdef CFG_ALLOC_DPRAM
+#if !defined(CONFIG_8260)
 	dpram_init,
 #endif
+#endif
 #if defined(CONFIG_BOARD_POSTCLK_INIT)
 	board_postclk_init,
 #endif