Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/src/arm/marvell/armada-xp-gp.dts b/src/arm/marvell/armada-xp-gp.dts
new file mode 100644
index 0000000..d1d348b
--- /dev/null
+++ b/src/arm/marvell/armada-xp-gp.dts
@@ -0,0 +1,230 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for Marvell Armada XP development board
+ * (DB-MV784MP-GP)
+ *
+ * Copyright (C) 2013-2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-xp-mv78460.dtsi"
+
+/ {
+ model = "Marvell Armada XP Development Board DB-MV784MP-GP";
+ compatible = "marvell,axp-gp", "marvell,armadaxp-mv78460", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ /*
+ * 8 GB of plug-in RAM modules by default.The amount
+ * of memory available can be changed by the
+ * bootloader according the size of the module
+ * actually plugged. However, memory between
+ * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
+ * the address range used for I/O (internal registers,
+ * MBus windows).
+ */
+ reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
+ <0x00000001 0x00000000 0x00000001 0x00000000>;
+ };
+
+ cpus {
+ pm_pic {
+ ctrl-gpios = <&gpio0 16 GPIO_ACTIVE_LOW>,
+ <&gpio0 17 GPIO_ACTIVE_LOW>,
+ <&gpio0 18 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x09, 0x09) 0 0 0xf1100000 0x10000
+ MBUS_ID(0x09, 0x05) 0 0 0xf1110000 0x10000
+ MBUS_ID(0x0c, 0x04) 0 0 0xf1200000 0x100000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+
+ /* NOR 16 MiB */
+ nor@0 {
+ compatible = "cfi-flash";
+ reg = <0 0x1000000>;
+ bank-width = <2>;
+ };
+ };
+
+ internal-regs {
+ serial@12000 {
+ status = "okay";
+ };
+ serial@12100 {
+ status = "okay";
+ };
+ serial@12200 {
+ status = "okay";
+ };
+ serial@12300 {
+ status = "okay";
+ };
+ pinctrl {
+ pinctrl-0 = <&pic_pins>;
+ pinctrl-names = "default";
+ pic_pins: pic-pins-0 {
+ marvell,pins = "mpp16", "mpp17",
+ "mpp18";
+ marvell,function = "gpio";
+ };
+ };
+ sata@a0000 {
+ nr-ports = <2>;
+ status = "okay";
+ };
+
+ ethernet@70000 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "qsgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <0>;
+ };
+ ethernet@74000 {
+ status = "okay";
+ phy = <&phy1>;
+ phy-mode = "qsgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <1>;
+ };
+ ethernet@30000 {
+ status = "okay";
+ phy = <&phy2>;
+ phy-mode = "qsgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <2>;
+ };
+ ethernet@34000 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "qsgmii";
+ buffer-manager = <&bm>;
+ bm,pool-long = <3>;
+ };
+
+ /* Front-side USB slot */
+ usb@50000 {
+ status = "okay";
+ };
+
+ /* Back-side USB slot */
+ usb@51000 {
+ status = "okay";
+ };
+
+ bm@c0000 {
+ status = "okay";
+ };
+
+ nand-controller@d0000 {
+ status = "okay";
+
+ nand@0 {
+ reg = <0>;
+ label = "pxa3xx_nand-0";
+ nand-rb = <0>;
+ nand-on-flash-bbt;
+ };
+ };
+ };
+
+ bm-bppi {
+ status = "okay";
+ };
+ };
+};
+
+&pciec {
+ status = "okay";
+
+ /*
+ * The 3 slots are physically present as
+ * standard PCIe slots on the board.
+ */
+ pcie@1,0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+ };
+ pcie@9,0 {
+ /* Port 2, Lane 0 */
+ status = "okay";
+ };
+ pcie@a,0 {
+ /* Port 3, Lane 0 */
+ status = "okay";
+ };
+};
+
+&mdio {
+ phy0: ethernet-phy@0 {
+ reg = <16>;
+ };
+
+ phy1: ethernet-phy@1 {
+ reg = <17>;
+ };
+
+ phy2: ethernet-phy@2 {
+ reg = <18>;
+ };
+
+ phy3: ethernet-phy@3 {
+ reg = <19>;
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
+};