diff --git a/Bindings/pinctrl/pincfg-node.yaml b/Bindings/pinctrl/pincfg-node.yaml
new file mode 100644
index 0000000..be81ed2
--- /dev/null
+++ b/Bindings/pinctrl/pincfg-node.yaml
@@ -0,0 +1,153 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/pincfg-node.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Generic Pin Configuration Node
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+description:
+  Many data items that are represented in a pin configuration node are common
+  and generic. Pin control bindings should use the properties defined below
+  where they are applicable; not all of these properties are relevant or useful
+  for all hardware or binding structures. Each individual binding document
+  should state which of these generic properties, if any, are used, and the
+  structure of the DT nodes that contain these properties.
+
+properties:
+  bias-disable:
+    type: boolean
+    description: disable any pin bias
+
+  bias-high-impedance:
+    type: boolean
+    description: high impedance mode ("third-state", "floating")
+
+  bias-bus-hold:
+    type: boolean
+    description: latch weakly
+
+  bias-pull-up:
+    oneOf:
+      - type: boolean
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description: pull up the pin. Takes as optional argument on hardware
+      supporting it the pull strength in Ohm.
+
+  bias-pull-down:
+    oneOf:
+      - type: boolean
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description: pull down the pin. Takes as optional argument on hardware
+      supporting it the pull strength in Ohm.
+
+  bias-pull-pin-default:
+    oneOf:
+      - type: boolean
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description: use pin-default pull state. Takes as optional argument on
+      hardware supporting it the pull strength in Ohm.
+
+  drive-push-pull:
+    oneOf:
+      - type: boolean
+      - $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [ 0, 1 ]
+        deprecated: true
+    description: drive actively high and low
+
+  drive-open-drain:
+    oneOf:
+      - type: boolean
+      - $ref: /schemas/types.yaml#/definitions/uint32
+        const: 1    # No known cases of 0
+        deprecated: true
+    description: drive with open drain
+
+  drive-open-source:
+    type: boolean
+    description: drive with open source
+
+  drive-strength:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: sink or source at most X mA
+
+  drive-strength-microamp:
+    description: sink or source at most X uA
+
+  input-enable:
+    type: boolean
+    description: enable input on pin (no effect on output, such as
+      enabling an input buffer)
+
+  input-disable:
+    type: boolean
+    description: disable input on pin (no effect on output, such as
+      disabling an input buffer)
+
+  input-schmitt-enable:
+    type: boolean
+    description: enable schmitt-trigger mode
+
+  input-schmitt-disable:
+    type: boolean
+    description: disable schmitt-trigger mode
+
+  input-debounce:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Takes the debounce time in usec as argument or 0 to disable
+      debouncing
+
+  power-source:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: select between different power supplies
+
+  low-power-enable:
+    type: boolean
+    description: enable low power mode
+
+  low-power-disable:
+    type: boolean
+    description: disable low power mode
+
+  output-disable:
+    type: boolean
+    description: disable output on a pin (such as disable an output buffer)
+
+  output-enable:
+    type: boolean
+    description: enable output on a pin without actively driving it
+      (such as enabling an output buffer)
+
+  output-impedance-ohms:
+    description: set the output impedance of a pin to at most X ohms
+
+  output-low:
+    type: boolean
+    description: set the pin to output mode with low level
+
+  output-high:
+    type: boolean
+    description: set the pin to output mode with high level
+
+  sleep-hardware-state:
+    type: boolean
+    description: indicate this is sleep related state which will be
+      programmed into the registers for the sleep state.
+
+  slew-rate:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: set the slew rate
+
+  skew-delay:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      this affects the expected clock skew on input pins
+      and the delay before latching a value to an output
+      pin. Typically indicates how many double-inverters are
+      used to delay the signal.
+
+additionalProperties: true