Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/Bindings/net/snps,dwc-qos-ethernet.txt b/Bindings/net/snps,dwc-qos-ethernet.txt
new file mode 100644
index 0000000..bb0224a
--- /dev/null
+++ b/Bindings/net/snps,dwc-qos-ethernet.txt
@@ -0,0 +1,168 @@
+* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)
+
+This binding is deprecated, but it continues to be supported, but new
+features should be preferably added to the stmmac binding document.
+
+This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service)
+IP block. The IP supports multiple options for bus type, clocking and reset
+structure, and feature list. Consequently, a number of properties and list
+entries in properties are marked as optional, or only required in specific HW
+configurations.
+
+Required properties:
+- compatible: One of:
+ - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10"
+ Represents the IP core when integrated into the Axis ARTPEC-6 SoC.
+ - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10"
+ Represents the IP core when integrated into the NVIDIA Tegra186 SoC.
+ - "snps,dwc-qos-ethernet-4.10"
+ This combination is deprecated. It should be treated as equivalent to
+ "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10". It is supported to be
+ compatible with earlier revisions of this binding.
+- reg: Address and length of the register set for the device
+- clocks: Phandle and clock specifiers for each entry in clock-names, in the
+ same order. See ../clock/clock-bindings.txt.
+- clock-names: May contain any/all of the following depending on the IP
+ configuration, in any order:
+ - "tx"
+ The EQOS transmit path clock. The HW signal name is clk_tx_i.
+ In some configurations (e.g. GMII/RGMII), this clock also drives the PHY TX
+ path. In other configurations, other clocks (such as tx_125, rmii) may
+ drive the PHY TX path.
+ - "rx"
+ The EQOS receive path clock. The HW signal name is clk_rx_i.
+ In some configurations (e.g. GMII/RGMII), this clock is derived from the
+ PHY's RX clock output. In other configurations, other clocks (such as
+ rx_125, rmii) may drive the EQOS RX path.
+ In cases where the PHY clock is directly fed into the EQOS receive path
+ without intervening logic, the DT need not represent this clock, since it
+ is assumed to be fully under the control of the PHY device/driver. In
+ cases where SoC integration adds additional logic to this path, such as a
+ SW-controlled clock gate, this clock should be represented in DT.
+ - "slave_bus"
+ The CPU/slave-bus (CSR) interface clock. This applies to any bus type;
+ APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or clk_csr_i (other
+ buses).
+ - "master_bus"
+ The master bus interface clock. Only required in configurations that use a
+ separate clock for the master and slave bus interfaces. The HW signal name
+ is hclk_i (AHB) or aclk_i (AXI).
+ - "ptp_ref"
+ The PTP reference clock. The HW signal name is clk_ptp_ref_i.
+ - "phy_ref_clk"
+ This clock is deprecated and should not be used by new compatible values.
+ It is equivalent to "tx".
+ - "apb_pclk"
+ This clock is deprecated and should not be used by new compatible values.
+ It is equivalent to "slave_bus".
+
+ Note: Support for additional IP configurations may require adding the
+ following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i,
+ clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i, clk_revmii_rx_i, clk_revmii_tx_i.
+ Configurations exist where multiple similar clocks are used at once, e.g. all
+ of clk_rx_125_i, clk_pmarx_0_i, clk_pmarx1_i. For this reason it is best to
+ extend the binding with a separate clock-names entry for each of those RX
+ clocks, rather than repurposing the existing "rx" clock-names entry as a
+ generic/logical clock in a similar fashion to "master_bus" and "slave_bus".
+ This will allow easy support for configurations that support multiple PHY
+ interfaces using a mux, and hence need to have explicit control over
+ specific RX clocks.
+
+ The following compatible values require the following set of clocks:
+ - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
+ - "slave_bus"
+ - "master_bus"
+ - "rx"
+ - "tx"
+ - "ptp_ref"
+ - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
+ - "slave_bus"
+ - "master_bus"
+ - "tx"
+ - "ptp_ref"
+ - "snps,dwc-qos-ethernet-4.10" (deprecated):
+ - "phy_ref_clk"
+ - "apb_clk"
+- interrupts: Should contain the core's combined interrupt signal
+- phy-mode: See ethernet.txt file in the same directory
+- resets: Phandle and reset specifiers for each entry in reset-names, in the
+ same order. See ../reset/reset.txt.
+- reset-names: May contain any/all of the following depending on the IP
+ configuration, in any order:
+ - "eqos". The reset to the entire module. The HW signal name is hreset_n
+ (AHB) or aresetn_i (AXI).
+
+ The following compatible values require the following set of resets:
+ (the reset properties may be omitted if empty)
+ - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
+ - "eqos".
+ - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
+ - None.
+ - "snps,dwc-qos-ethernet-4.10" (deprecated):
+ - None.
+
+Optional properties:
+- dma-coherent: Present if dma operations are coherent
+- phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY.
+ See ../gpio/gpio.txt.
+- snps,en-lpi: If present it enables use of the AXI low-power interface
+- snps,write-requests: Number of write requests that the AXI port can issue.
+ It depends on the SoC configuration.
+- snps,read-requests: Number of read requests that the AXI port can issue.
+ It depends on the SoC configuration.
+- snps,burst-map: Bitmap of allowed AXI burst lengths, with the LSB
+ representing 4, then 8 etc.
+- snps,txpbl: DMA Programmable burst length for the TX DMA
+- snps,rxpbl: DMA Programmable burst length for the RX DMA
+- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during
+ TX low-power mode.
+- phy-handle: See ethernet.txt file in the same directory
+- mdio device tree subnode: When the GMAC has a phy connected to its local
+ mdio, there must be device tree subnode with the following
+ required properties:
+ - compatible: Must be "snps,dwc-qos-ethernet-mdio".
+ - #address-cells: Must be <1>.
+ - #size-cells: Must be <0>.
+
+ For each phy on the mdio bus, there must be a node with the following
+ fields:
+
+ - reg: phy id used to communicate to phy.
+ - device_type: Must be "ethernet-phy".
+ - fixed-mode device tree subnode: see fixed-link.txt in the same directory
+
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
+
+Examples:
+ethernet2@40010000 {
+ clock-names = "phy_ref_clk", "apb_pclk";
+ clocks = <&clkc 17>, <&clkc 15>;
+ compatible = "snps,dwc-qos-ethernet-4.10";
+ interrupt-parent = <&intc>;
+ interrupts = <0x0 0x1e 0x4>;
+ reg = <0x40010000 0x4000>;
+ phy-handle = <&phy2>;
+ phy-mode = "gmii";
+ phy-reset-gpios = <&gpioctlr 43 GPIO_ACTIVE_LOW>;
+
+ snps,en-tx-lpi-clockgating;
+ snps,en-lpi;
+ snps,write-requests = <2>;
+ snps,read-requests = <16>;
+ snps,burst-map = <0x7>;
+ snps,txpbl = <8>;
+ snps,rxpbl = <2>;
+
+ dma-coherent;
+
+ mdio {
+ #address-cells = <0x1>;
+ #size-cells = <0x0>;
+ phy2: phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ device_type = "ethernet-phy";
+ reg = <0x1>;
+ };
+ };
+};