Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/Bindings/net/sff,sfp.yaml b/Bindings/net/sff,sfp.yaml
new file mode 100644
index 0000000..973e478
--- /dev/null
+++ b/Bindings/net/sff,sfp.yaml
@@ -0,0 +1,143 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/sff,sfp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
+ Transceiver
+
+maintainers:
+ - Russell King <linux@armlinux.org.uk>
+
+properties:
+ compatible:
+ enum:
+ - sff,sfp # for SFP modules
+ - sff,sff # for soldered down SFF modules
+
+ i2c-bus:
+ $ref: /schemas/types.yaml#/definitions/phandle
+ description:
+ phandle of an I2C bus controller for the SFP two wire serial
+
+ maximum-power-milliwatt:
+ minimum: 1000
+ default: 1000
+ description:
+ Maximum module power consumption Specifies the maximum power consumption
+ allowable by a module in the slot, in milli-Watts. Presently, modules can
+ be up to 1W, 1.5W or 2W.
+
+ "mod-def0-gpios":
+ maxItems: 1
+ description:
+ GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module
+ presence input gpio signal, active (module absent) high. Must not be
+ present for SFF modules
+
+ "los-gpios":
+ maxItems: 1
+ description:
+ GPIO phandle and a specifier of the Receiver Loss of Signal Indication
+ input gpio signal, active (signal lost) high
+
+ "tx-fault-gpios":
+ maxItems: 1
+ description:
+ GPIO phandle and a specifier of the Module Transmitter Fault input gpio
+ signal, active (fault condition) high
+
+ "tx-disable-gpios":
+ maxItems: 1
+ description:
+ GPIO phandle and a specifier of the Transmitter Disable output gpio
+ signal, active (Tx disable) high
+
+ "rate-select0-gpios":
+ maxItems: 1
+ description:
+ GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0)
+ output gpio signal, low - low Rx rate, high - high Rx rate Must not be
+ present for SFF modules
+
+ "rate-select1-gpios":
+ maxItems: 1
+ description:
+ GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1)
+ output gpio signal (SFP+ only), low - low Tx rate, high - high Tx rate. Must
+ not be present for SFF modules
+
+allOf:
+ - if:
+ properties:
+ compatible:
+ contains:
+ const: sff,sff
+ then:
+ properties:
+ mod-def0-gpios: false
+ rate-select0-gpios: false
+ rate-select1-gpios: false
+
+required:
+ - compatible
+ - i2c-bus
+
+additionalProperties: false
+
+examples:
+ - | # Direct serdes to SFP connection
+ #include <dt-bindings/gpio/gpio.h>
+
+ sfp1: sfp {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfp_1g_i2c>;
+ los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
+ maximum-power-milliwatt = <1000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
+ tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
+ };
+
+ ethernet {
+ phy-names = "comphy";
+ phys = <&cps_comphy5 0>;
+ sfp = <&sfp1>;
+ };
+
+ - | # Serdes to PHY to SFP connection
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+ sfp2: sfp {
+ compatible = "sff,sfp";
+ i2c-bus = <&sfp_i2c>;
+ los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&cps_sfpp0_pins>;
+ tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy: ethernet-phy@0 {
+ compatible = "ethernet-phy-ieee802.3-c45";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
+ reg = <0>;
+ interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
+ sfp = <&sfp2>;
+ };
+ };
+
+ ethernet {
+ phy = <&phy>;
+ phy-mode = "10gbase-kr";
+ };