Squashed 'dts/upstream/' content from commit aaba2d45dc2a
git-subtree-dir: dts/upstream
git-subtree-split: aaba2d45dc2a1b3bbb710f2a3808ee1c9f340abe
diff --git a/Bindings/net/fsl-tsec-phy.txt b/Bindings/net/fsl-tsec-phy.txt
new file mode 100644
index 0000000..047bdf7
--- /dev/null
+++ b/Bindings/net/fsl-tsec-phy.txt
@@ -0,0 +1,89 @@
+* MDIO IO device
+
+The MDIO is a bus to which the PHY devices are connected. For each
+device that exists on this bus, a child node should be created. See
+the definition of the PHY node in booting-without-of.txt for an example
+of how to define a PHY.
+
+Required properties:
+ - reg : Offset and length of the register set for the device, and optionally
+ the offset and length of the TBIPA register (TBI PHY address
+ register). If TBIPA register is not specified, the driver will
+ attempt to infer it from the register set specified (your mileage may
+ vary).
+ - compatible : Should define the compatible device type for the
+ mdio. Currently supported strings/devices are:
+ - "fsl,gianfar-tbi"
+ - "fsl,gianfar-mdio"
+ - "fsl,etsec2-tbi"
+ - "fsl,etsec2-mdio"
+ - "fsl,ucc-mdio"
+ - "fsl,fman-mdio"
+ When device_type is "mdio", the following strings are also considered:
+ - "gianfar"
+ - "ucc_geth_phy"
+
+Example:
+
+ mdio@24520 {
+ reg = <24520 20>;
+ compatible = "fsl,gianfar-mdio";
+
+ ethernet-phy@0 {
+ ......
+ };
+ };
+
+* TBI Internal MDIO bus
+
+As of this writing, every tsec is associated with an internal TBI PHY.
+This PHY is accessed through the local MDIO bus. These buses are defined
+similarly to the mdio buses, except they are compatible with "fsl,gianfar-tbi".
+The TBI PHYs underneath them are similar to normal PHYs, but the reg property
+is considered instructive, rather than descriptive. The reg property should
+be chosen so it doesn't interfere with other PHYs on the bus.
+
+* Gianfar-compatible ethernet nodes
+
+Properties:
+
+ - device_type : Should be "network"
+ - model : Model of the device. Can be "TSEC", "eTSEC", or "FEC"
+ - compatible : Should be "gianfar"
+ - reg : Offset and length of the register set for the device
+ - interrupts : For FEC devices, the first interrupt is the device's
+ interrupt. For TSEC and eTSEC devices, the first interrupt is
+ transmit, the second is receive, and the third is error.
+ - phy-handle : See ethernet.txt file in the same directory.
+ - fixed-link : See fixed-link.txt in the same directory.
+ - phy-connection-type : See ethernet.txt file in the same directory.
+ This property is only really needed if the connection is of type
+ "rgmii-id", as all other connection types are detected by hardware.
+ - fsl,magic-packet : If present, indicates that the hardware supports
+ waking up via magic packet.
+ - fsl,wake-on-filer : If present, indicates that the hardware supports
+ waking up by Filer General Purpose Interrupt (FGPI) asserted on the
+ Rx int line. This is an advanced power management capability allowing
+ certain packet types (user) defined by filer rules to wake up the system.
+ - bd-stash : If present, indicates that the hardware supports stashing
+ buffer descriptors in the L2.
+ - rx-stash-len : Denotes the number of bytes of a received buffer to stash
+ in the L2.
+ - rx-stash-idx : Denotes the index of the first byte from the received
+ buffer to stash in the L2.
+
+Example:
+ ethernet@24000 {
+ device_type = "network";
+ model = "TSEC";
+ compatible = "gianfar";
+ reg = <0x24000 0x1000>;
+ local-mac-address = [ 00 E0 0C 00 73 00 ];
+ interrupts = <29 2 30 2 34 2>;
+ interrupt-parent = <&mpic>;
+ phy-handle = <&phy0>
+ };
+
+* Gianfar PTP clock nodes
+
+Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt