diff --git a/Bindings/net/cpsw.txt b/Bindings/net/cpsw.txt
new file mode 100644
index 0000000..ef655f3
--- /dev/null
+++ b/Bindings/net/cpsw.txt
@@ -0,0 +1,132 @@
+TI SoC Ethernet Switch Controller Device Tree Bindings
+------------------------------------------------------
+
+Required properties:
+- compatible		: Should be one of the below:-
+			  "ti,cpsw" for backward compatible
+			  "ti,am335x-cpsw" for AM335x controllers
+			  "ti,am4372-cpsw" for AM437x controllers
+			  "ti,dra7-cpsw" for DRA7x controllers
+- reg			: physical base address and size of the cpsw
+			  registers map
+- interrupts		: property with a value describing the interrupt
+			  number
+- cpdma_channels 	: Specifies number of channels in CPDMA
+- ale_entries		: Specifies No of entries ALE can hold
+- bd_ram_size		: Specifies internal descriptor RAM size
+- mac_control		: Specifies Default MAC control register content
+			  for the specific platform
+- slaves		: Specifies number for slaves
+- active_slave		: Specifies the slave to use for time stamping,
+			  ethtool and SIOCGMIIPHY
+- cpsw-phy-sel		: Specifies the phandle to the CPSW phy mode selection
+			  device. See also cpsw-phy-sel.txt for its binding.
+			  Note that in legacy cases cpsw-phy-sel may be
+			  a child device instead of a phandle
+			  (DEPRECATED, use phys property instead).
+
+Optional properties:
+- ti,hwmods		: Must be "cpgmac0"
+- dual_emac		: Specifies Switch to act as Dual EMAC
+- syscon		: Phandle to the system control device node, which is
+			  the control module device of the am33x
+- mode-gpios		: Should be added if one/multiple gpio lines are
+			  required to be driven so that cpsw data lines
+			  can be connected to the phy via selective mux.
+			  For example in dra72x-evm, pcf gpio has to be
+			  driven low so that cpsw slave 0 and phy data
+			  lines are connected via mux.
+- cpts_clock_mult	: Numerator to convert input clock ticks into nanoseconds
+- cpts_clock_shift	: Denominator to convert input clock ticks into nanoseconds
+			  Mult and shift will be calculated basing on CPTS
+			  rftclk frequency if both cpts_clock_shift and
+			  cpts_clock_mult properties are not provided.
+
+Slave Properties:
+Required properties:
+- phy-mode		: See ethernet.txt file in the same directory
+- phys			: phandle on phy-gmii-sel PHY (see phy/ti-phy-gmii-sel.txt)
+
+Optional properties:
+- dual_emac_res_vlan	: Specifies VID to be used to segregate the ports
+- phy_id		: Specifies slave phy id (deprecated, use phy-handle)
+- phy-handle		: See ethernet.txt file in the same directory
+
+The MAC address will be determined using the optional properties
+defined in ethernet.txt.
+
+Slave sub-nodes:
+- fixed-link		: See fixed-link.txt file in the same directory
+
+Note: Exactly one of phy_id, phy-handle, or fixed-link must be specified.
+
+Note: "ti,hwmods" field is used to fetch the base address and irq
+resources from TI, omap hwmod data base during device registration.
+Future plan is to migrate hwmod data base contents into device tree
+blob so that, all the required data will be used from device tree dts
+file.
+
+Examples:
+
+	mac: ethernet@4a100000 {
+		compatible = "ti,cpsw";
+		reg = <0x4A100000 0x1000>;
+		interrupts = <55 0x4>;
+		interrupt-parent = <&intc>;
+		cpdma_channels = <8>;
+		ale_entries = <1024>;
+		bd_ram_size = <0x2000>;
+		rx_descs = <64>;
+		mac_control = <0x20>;
+		slaves = <2>;
+		active_slave = <0>;
+		cpts_clock_mult = <0x80000000>;
+		cpts_clock_shift = <29>;
+		syscon = <&cm>;
+		cpsw-phy-sel = <&phy_sel>;
+		cpsw_emac0: slave@0 {
+			phy_id = <&davinci_mdio>, <0>;
+			phy-mode = "rgmii-txid";
+			/* Filled in by U-Boot */
+			mac-address = [ 00 00 00 00 00 00 ];
+			phys = <&phy_gmii_sel 1 0>;
+		};
+		cpsw_emac1: slave@1 {
+			phy_id = <&davinci_mdio>, <1>;
+			phy-mode = "rgmii-txid";
+			/* Filled in by U-Boot */
+			mac-address = [ 00 00 00 00 00 00 ];
+			phys = <&phy_gmii_sel 2 0>;
+		};
+	};
+
+(or)
+	mac: ethernet@4a100000 {
+		compatible = "ti,cpsw";
+		ti,hwmods = "cpgmac0";
+		cpdma_channels = <8>;
+		ale_entries = <1024>;
+		bd_ram_size = <0x2000>;
+		rx_descs = <64>;
+		mac_control = <0x20>;
+		slaves = <2>;
+		active_slave = <0>;
+		cpts_clock_mult = <0x80000000>;
+		cpts_clock_shift = <29>;
+		syscon = <&cm>;
+		cpsw-phy-sel = <&phy_sel>;
+		cpsw_emac0: slave@0 {
+			phy_id = <&davinci_mdio>, <0>;
+			phy-mode = "rgmii-txid";
+			/* Filled in by U-Boot */
+			mac-address = [ 00 00 00 00 00 00 ];
+			phys = <&phy_gmii_sel 1 0>;
+		};
+		cpsw_emac1: slave@1 {
+			phy_id = <&davinci_mdio>, <1>;
+			phy-mode = "rgmii-txid";
+			/* Filled in by U-Boot */
+			mac-address = [ 00 00 00 00 00 00 ];
+			phys = <&phy_gmii_sel 2 0>;
+		};
+	};