diff --git a/Bindings/mips/ath79-soc.txt b/Bindings/mips/ath79-soc.txt
new file mode 100644
index 0000000..88a12a4
--- /dev/null
+++ b/Bindings/mips/ath79-soc.txt
@@ -0,0 +1,21 @@
+Binding for Qualcomm Atheros AR7xxx/AR9XXX SoC
+
+Each device tree must specify a compatible value for the AR SoC
+it uses in the compatible property of the root node. The compatible
+value must be one of the following values:
+
+- qca,ar7130
+- qca,ar7141
+- qca,ar7161
+- qca,ar7240
+- qca,ar7241
+- qca,ar7242
+- qca,ar9130
+- qca,ar9132
+- qca,ar9330
+- qca,ar9331
+- qca,ar9341
+- qca,ar9342
+- qca,ar9344
+- qca,qca9556
+- qca,qca9558
diff --git a/Bindings/mips/brcm/soc.txt b/Bindings/mips/brcm/soc.txt
new file mode 100644
index 0000000..3a66d3c
--- /dev/null
+++ b/Bindings/mips/brcm/soc.txt
@@ -0,0 +1,166 @@
+* Broadcom cable/DSL/settop platforms
+
+Required properties:
+
+- compatible: "brcm,bcm3368", "brcm,bcm3384", "brcm,bcm33843"
+              "brcm,bcm3384-viper", "brcm,bcm33843-viper"
+              "brcm,bcm6328", "brcm,bcm6358", "brcm,bcm6362", "brcm,bcm6368",
+              "brcm,bcm63168", "brcm,bcm63268",
+              "brcm,bcm7125", "brcm,bcm7346", "brcm,bcm7358", "brcm,bcm7360",
+              "brcm,bcm7362", "brcm,bcm7420", "brcm,bcm7425"
+
+The experimental -viper variants are for running Linux on the 3384's
+BMIPS4355 cable modem CPU instead of the BMIPS5000 application processor.
+
+Power management
+----------------
+
+For power management (particularly, S2/S3/S5 system suspend), the following SoC
+components are needed:
+
+= Always-On control block (AON CTRL)
+
+This hardware provides control registers for the "always-on" (even in low-power
+modes) hardware, such as the Power Management State Machine (PMSM).
+
+Required properties:
+- compatible     : should be one of
+		   "brcm,bcm7425-aon-ctrl"
+		   "brcm,bcm7429-aon-ctrl"
+		   "brcm,bcm7435-aon-ctrl" and
+		   "brcm,brcmstb-aon-ctrl"
+- reg            : the register start and length for the AON CTRL block
+
+Example:
+
+syscon@410000 {
+	compatible = "brcm,bcm7425-aon-ctrl", "brcm,brcmstb-aon-ctrl";
+	reg = <0x410000 0x400>;
+};
+
+= Memory controllers
+
+A Broadcom STB SoC typically has a number of independent memory controllers,
+each of which may have several associated hardware blocks, which are versioned
+independently (control registers, DDR PHYs, etc.). One might consider
+describing these controllers as a parent "memory controllers" block, which
+contains N sub-nodes (one for each controller in the system), each of which is
+associated with a number of hardware register resources (e.g., its PHY.
+
+== MEMC (MEMory Controller)
+
+Represents a single memory controller instance.
+
+Required properties:
+- compatible     : should contain "brcm,brcmstb-memc" and "simple-bus"
+- ranges	 : should contain the child address in the parent address
+		   space, must be 0 here, and the register start and length of
+		   the entire memory controller (including all sub nodes: DDR PHY,
+		   arbiter, etc.)
+- #address-cells : must be 1
+- #size-cells	 : must be 1
+
+Example:
+
+	memory-controller@0 {
+		compatible = "brcm,brcmstb-memc", "simple-bus";
+		ranges = <0x0 0x0 0xa000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		memc-arb@1000 {
+			...
+		};
+
+		memc-ddr@2000 {
+			...
+		};
+
+		ddr-phy@6000 {
+			...
+		};
+	};
+
+Should contain subnodes for any of the following relevant hardware resources:
+
+== DDR PHY control
+
+Control registers for this memory controller's DDR PHY.
+
+Required properties:
+- compatible     : should contain one of these
+		   "brcm,brcmstb-ddr-phy-v64.5"
+		   "brcm,brcmstb-ddr-phy"
+
+- reg            : the DDR PHY register range and length
+
+Example:
+
+	ddr-phy@6000 {
+		compatible = "brcm,brcmstb-ddr-phy-v64.5";
+		reg = <0x6000 0xc8>;
+	};
+
+== DDR memory controller sequencer
+
+Control registers for this memory controller's DDR memory sequencer
+
+Required properties:
+- compatible     : should contain one of these
+		   "brcm,bcm7425-memc-ddr"
+		   "brcm,bcm7429-memc-ddr"
+		   "brcm,bcm7435-memc-ddr" and
+		   "brcm,brcmstb-memc-ddr"
+
+- reg            : the DDR sequencer register range and length
+
+Example:
+
+	memc-ddr@2000 {
+		compatible = "brcm,bcm7425-memc-ddr", "brcm,brcmstb-memc-ddr";
+		reg = <0x2000 0x300>;
+	};
+
+== MEMC Arbiter
+
+The memory controller arbiter is responsible for memory clients allocation
+(bandwidth, priorities etc.) and needs to have its contents restored during
+deep sleep states (S3).
+
+Required properties:
+
+- compatible	: should contain one of these
+		  "brcm,brcmstb-memc-arb-v10.0.0.0"
+		  "brcm,brcmstb-memc-arb"
+
+- reg		: the DDR Arbiter register range and length
+
+Example:
+
+	memc-arb@1000 {
+		compatible = "brcm,brcmstb-memc-arb-v10.0.0.0";
+		reg = <0x1000 0x248>;
+	};
+
+== Timers
+
+The Broadcom STB chips contain a timer block with several general purpose
+timers that can be used.
+
+Required properties:
+
+- compatible	: should contain one of:
+		  "brcm,bcm7425-timers"
+		  "brcm,bcm7429-timers"
+		  "brcm,bcm7435-timers" and
+		  "brcm,brcmstb-timers"
+- reg		: the timers register range
+- interrupts	: the interrupt line for this timer block
+
+Example:
+
+	timers: timer@4067c0 {
+		compatible = "brcm,bcm7425-timers", "brcm,brcmstb-timers";
+		reg = <0x4067c0 0x40>;
+		interrupts = <&periph_intc 19>;
+	};
diff --git a/Bindings/mips/brcm/soc.yaml b/Bindings/mips/brcm/soc.yaml
new file mode 100644
index 0000000..975945c
--- /dev/null
+++ b/Bindings/mips/brcm/soc.yaml
@@ -0,0 +1,96 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/brcm/soc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom cable/DSL/settop platforms
+
+maintainers:
+  - Florian Fainelli <f.fainelli@gmail.com>
+
+description: |
+    Boards Broadcom cable/DSL/settop SoC shall have the following properties.
+    The experimental -viper variants are for running Linux on the 3384's
+    BMIPS4355 cable modem CPU instead of the BMIPS5000 application processor.
+
+properties:
+  $nodename:
+    const: '/'
+
+  compatible:
+    enum:
+      - brcm,bcm3368
+      - brcm,bcm3384
+      - brcm,bcm33843
+      - brcm,bcm3384-viper
+      - brcm,bcm33843-viper
+      - brcm,bcm6328
+      - brcm,bcm6358
+      - brcm,bcm6362
+      - brcm,bcm6368
+      - brcm,bcm63168
+      - brcm,bcm63268
+      - brcm,bcm7125
+      - brcm,bcm7346
+      - brcm,bcm7358
+      - brcm,bcm7360
+      - brcm,bcm7362
+      - brcm,bcm7420
+      - brcm,bcm7425
+
+  cpus:
+    type: object
+    additionalProperties: false
+    properties:
+      '#address-cells':
+        const: 1
+
+      '#size-cells':
+        const: 0
+
+      mips-hpt-frequency:
+        description: MIPS counter high precision timer frequency.
+         This is common to all CPUs in the system so it lives
+         under the "cpus" node.
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+    patternProperties:
+      "^cpu@[0-9]$":
+        type: object
+        $ref: /schemas/mips/cpus.yaml#
+        unevaluatedProperties: false
+
+    required:
+      - mips-hpt-frequency
+
+additionalProperties: true
+
+examples:
+  - |
+     / {
+         compatible = "brcm,bcm3368";
+         #address-cells = <1>;
+         #size-cells = <1>;
+         model = "Broadcom 3368";
+
+         cpus {
+           #address-cells = <1>;
+           #size-cells = <0>;
+
+           mips-hpt-frequency = <150000000>;
+
+           cpu@0 {
+             compatible = "brcm,bmips4350";
+             device_type = "cpu";
+             reg = <0>;
+           };
+
+           cpu@1 {
+             compatible = "brcm,bmips4350";
+             device_type = "cpu";
+             reg = <1>;
+           };
+         };
+       };
+...
diff --git a/Bindings/mips/cavium/bootbus.txt b/Bindings/mips/cavium/bootbus.txt
new file mode 100644
index 0000000..6581478
--- /dev/null
+++ b/Bindings/mips/cavium/bootbus.txt
@@ -0,0 +1,126 @@
+* Boot Bus
+
+The Octeon Boot Bus is a configurable parallel bus with 8 chip
+selects.  Each chip select is independently configurable.
+
+Properties:
+- compatible: "cavium,octeon-3860-bootbus"
+
+  Compatibility with all cn3XXX, cn5XXX and cn6XXX SOCs.
+
+- reg: The base address of the Boot Bus' register bank.
+
+- #address-cells: Must be <2>.  The first cell is the chip select
+   within the bootbus.  The second cell is the offset from the chip select.
+
+- #size-cells: Must be <1>.
+
+- ranges: There must be one one triplet of (child-bus-address,
+  parent-bus-address, length) for each active chip select.  If the
+  length element for any triplet is zero, the chip select is disabled,
+  making it inactive.
+
+The configuration parameters for each chip select are stored in child
+nodes.
+
+Configuration Properties:
+- compatible:  "cavium,octeon-3860-bootbus-config"
+
+- cavium,cs-index: A single cell indicating the chip select that
+  corresponds to this configuration.
+
+- cavium,t-adr: A cell specifying the ADR timing (in nS).
+
+- cavium,t-ce: A cell specifying the CE timing (in nS).
+
+- cavium,t-oe: A cell specifying the OE timing (in nS).
+
+- cavium,t-we: A cell specifying the WE timing (in nS).
+
+- cavium,t-rd-hld: A cell specifying the RD_HLD timing (in nS).
+
+- cavium,t-wr-hld: A cell specifying the WR_HLD timing (in nS).
+
+- cavium,t-pause: A cell specifying the PAUSE timing (in nS).
+
+- cavium,t-wait: A cell specifying the WAIT timing (in nS).
+
+- cavium,t-page: A cell specifying the PAGE timing (in nS).
+
+- cavium,t-rd-dly: A cell specifying the RD_DLY timing (in nS).
+
+- cavium,pages: A cell specifying the PAGES parameter (0 = 8 bytes, 1
+  = 2 bytes, 2 = 4 bytes, 3 = 8 bytes).
+
+- cavium,wait-mode: Optional.  If present, wait mode (WAITM) is selected.
+
+- cavium,page-mode: Optional.  If present, page mode (PAGEM) is selected.
+
+- cavium,bus-width: A cell specifying the WIDTH parameter (in bits) of
+  the bus for this chip select.
+
+- cavium,ale-mode: Optional.  If present, ALE mode is selected.
+
+- cavium,sam-mode: Optional.  If present, SAM mode is selected.
+
+- cavium,or-mode: Optional.  If present, OR mode is selected.
+
+Example:
+	bootbus: bootbus@1180000000000 {
+		compatible = "cavium,octeon-3860-bootbus";
+		reg = <0x11800 0x00000000 0x0 0x200>;
+		/* The chip select number and offset */
+		#address-cells = <2>;
+		/* The size of the chip select region */
+		#size-cells = <1>;
+		ranges = <0 0  0x0 0x1f400000  0xc00000>,
+			 <1 0  0x10000 0x30000000  0>,
+			 <2 0  0x10000 0x40000000  0>,
+			 <3 0  0x10000 0x50000000  0>,
+			 <4 0  0x0 0x1d020000  0x10000>,
+			 <5 0  0x0 0x1d040000  0x10000>,
+			 <6 0  0x0 0x1d050000  0x10000>,
+			 <7 0  0x10000 0x90000000  0>;
+
+			cavium,cs-config@0 {
+			compatible = "cavium,octeon-3860-bootbus-config";
+			cavium,cs-index = <0>;
+			cavium,t-adr  = <20>;
+			cavium,t-ce   = <60>;
+			cavium,t-oe   = <60>;
+			cavium,t-we   = <45>;
+			cavium,t-rd-hld = <35>;
+			cavium,t-wr-hld = <45>;
+			cavium,t-pause  = <0>;
+			cavium,t-wait   = <0>;
+			cavium,t-page   = <35>;
+			cavium,t-rd-dly = <0>;
+
+			cavium,pages     = <0>;
+			cavium,bus-width = <8>;
+		};
+		.
+		.
+		.
+		cavium,cs-config@6 {
+			compatible = "cavium,octeon-3860-bootbus-config";
+			cavium,cs-index = <6>;
+			cavium,t-adr  = <5>;
+			cavium,t-ce   = <300>;
+			cavium,t-oe   = <270>;
+			cavium,t-we   = <150>;
+			cavium,t-rd-hld = <100>;
+			cavium,t-wr-hld = <70>;
+			cavium,t-pause  = <0>;
+			cavium,t-wait   = <0>;
+			cavium,t-page   = <320>;
+			cavium,t-rd-dly = <0>;
+
+			cavium,pages     = <0>;
+			cavium,wait-mode;
+			cavium,bus-width = <16>;
+		};
+		.
+		.
+		.
+	};
diff --git a/Bindings/mips/cavium/cib.txt b/Bindings/mips/cavium/cib.txt
new file mode 100644
index 0000000..410efa3
--- /dev/null
+++ b/Bindings/mips/cavium/cib.txt
@@ -0,0 +1,41 @@
+* Cavium Interrupt Bus widget
+
+Properties:
+- compatible: "cavium,octeon-7130-cib"
+
+  Compatibility with cn70XX SoCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: Two elements consisting of the addresses of the RAW and EN
+  registers of the CIB block
+
+- cavium,max-bits: The index (zero based) of the highest numbered bit
+  in the CIB block.
+
+- interrupts: The CIU line to which the CIB block is connected.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bit within the
+   CIB.  The second cell specifies the triggering semantics of the
+   line.
+
+Example:
+
+	interrupt-controller@107000000e000 {
+		compatible = "cavium,octeon-7130-cib";
+		reg = <0x10700 0x0000e000 0x0 0x8>, /* RAW */
+		      <0x10700 0x0000e100 0x0 0x8>; /* EN */
+		cavium,max-bits = <23>;
+
+		interrupt-controller;
+		interrupt-parent = <&ciu>;
+		interrupts = <1 24>;
+		/* Interrupts are specified by two parts:
+		 * 1) Bit number in the CIB* registers
+		 * 2) Triggering (1 - edge rising
+		 *		  2 - edge falling
+		 *		  4 - level active high
+		 *		  8 - level active low)
+		 */
+		#interrupt-cells = <2>;
+	};
diff --git a/Bindings/mips/cavium/ciu.txt b/Bindings/mips/cavium/ciu.txt
new file mode 100644
index 0000000..2c2d074
--- /dev/null
+++ b/Bindings/mips/cavium/ciu.txt
@@ -0,0 +1,26 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-3860-ciu"
+
+  Compatibility with all cn3XXX, cn5XXX and cn63XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bank within
+   the CIU and may have a value of 0 or 1.  The second cell is the bit
+   within the bank and may have a value between 0 and 63.
+
+Example:
+	interrupt-controller@1070000000000 {
+		compatible = "cavium,octeon-3860-ciu";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Controller register (0 or 1)
+		 * 2) Bit within the register (0..63)
+		 */
+		#interrupt-cells = <2>;
+		reg = <0x10700 0x00000000 0x0 0x7000>;
+	};
diff --git a/Bindings/mips/cavium/ciu2.txt b/Bindings/mips/cavium/ciu2.txt
new file mode 100644
index 0000000..0ec7ba8
--- /dev/null
+++ b/Bindings/mips/cavium/ciu2.txt
@@ -0,0 +1,27 @@
+* Central Interrupt Unit
+
+Properties:
+- compatible: "cavium,octeon-6880-ciu2"
+
+  Compatibility with 68XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is the bank within
+  the CIU and may have a value between 0 and 63.  The second cell is
+  the bit within the bank and may also have a value between 0 and 63.
+
+Example:
+	interrupt-controller@1070100000000 {
+		compatible = "cavium,octeon-6880-ciu2";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Controller register (0..63)
+		 * 2) Bit within the register (0..63)
+		 */
+		#address-cells = <0>;
+		#interrupt-cells = <2>;
+		reg = <0x10701 0x00000000 0x0 0x4000000>;
+	};
diff --git a/Bindings/mips/cavium/ciu3.txt b/Bindings/mips/cavium/ciu3.txt
new file mode 100644
index 0000000..616862a
--- /dev/null
+++ b/Bindings/mips/cavium/ciu3.txt
@@ -0,0 +1,27 @@
+* Central Interrupt Unit v3
+
+Properties:
+- compatible: "cavium,octeon-7890-ciu3"
+
+  Compatibility with 78XX and 73XX SOCs.
+
+- interrupt-controller:  This is an interrupt controller.
+
+- reg: The base address of the CIU's register bank.
+
+- #interrupt-cells: Must be <2>.  The first cell is source number.
+  The second cell indicates the triggering semantics, and may have a
+  value of either 4 for level semantics, or 1 for edge semantics.
+
+Example:
+	interrupt-controller@1010000000000 {
+		compatible = "cavium,octeon-7890-ciu3";
+		interrupt-controller;
+		/* Interrupts are specified by two parts:
+		 * 1) Source number (20 significant bits)
+		 * 2) Trigger type: (4 == level, 1 == edge)
+		 */
+		#address-cells = <0>;
+		#interrupt-cells = <2>;
+		reg = <0x10100 0x00000000 0x0 0xb0000000>;
+	};
diff --git a/Bindings/mips/cavium/dma-engine.txt b/Bindings/mips/cavium/dma-engine.txt
new file mode 100644
index 0000000..a5bdff4
--- /dev/null
+++ b/Bindings/mips/cavium/dma-engine.txt
@@ -0,0 +1,21 @@
+* DMA Engine.
+
+The Octeon DMA Engine transfers between the Boot Bus and main memory.
+The DMA Engine will be referred to by phandle by any device that is
+connected to it.
+
+Properties:
+- compatible: "cavium,octeon-5750-bootbus-dma"
+
+  Compatibility with all cn52XX, cn56XX and cn6XXX SOCs.
+
+- reg: The base address of the DMA Engine's register bank.
+
+- interrupts: A single interrupt specifier.
+
+Example:
+	dma0: dma-engine@1180000000100 {
+		compatible = "cavium,octeon-5750-bootbus-dma";
+		reg = <0x11800 0x00000100 0x0 0x8>;
+		interrupts = <0 63>;
+	};
diff --git a/Bindings/mips/cavium/sata-uctl.txt b/Bindings/mips/cavium/sata-uctl.txt
new file mode 100644
index 0000000..3bd3c2f
--- /dev/null
+++ b/Bindings/mips/cavium/sata-uctl.txt
@@ -0,0 +1,42 @@
+* UCTL SATA controller glue
+
+UCTL is the bridge unit between the I/O interconnect (an internal bus)
+and the SATA AHCI host controller (UAHC). It performs the following functions:
+	- provides interfaces for the applications to access the UAHC AHCI
+	  registers on the CN71XX I/O space.
+	- provides a bridge for UAHC to fetch AHCI command table entries and data
+	  buffers from Level 2 Cache.
+	- posts interrupts to the CIU.
+	- contains registers that:
+		- control the behavior of the UAHC
+		- control the clock/reset generation to UAHC
+		- control endian swapping for all UAHC registers and DMA accesses
+
+Properties:
+
+- compatible: "cavium,octeon-7130-sata-uctl"
+
+  Compatibility with the cn7130 SOC.
+
+- reg: The base address of the UCTL register bank.
+
+- #address-cells, #size-cells, ranges and dma-ranges must be present and hold
+	suitable values to map all child nodes.
+
+Example:
+
+	uctl@118006c000000 {
+		compatible = "cavium,octeon-7130-sata-uctl";
+		reg = <0x11800 0x6c000000 0x0 0x100>;
+		ranges; /* Direct mapping */
+		dma-ranges;
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		sata: sata@16c0000000000 {
+			compatible = "cavium,octeon-7130-ahci";
+			reg = <0x16c00 0x00000000 0x0 0x200>;
+			interrupt-parent = <&cibsata>;
+			interrupts = <2 4>; /* Bit: 2, level */
+		};
+	};
diff --git a/Bindings/mips/cavium/uctl.txt b/Bindings/mips/cavium/uctl.txt
new file mode 100644
index 0000000..aa66b9b
--- /dev/null
+++ b/Bindings/mips/cavium/uctl.txt
@@ -0,0 +1,46 @@
+* UCTL USB controller glue
+
+Properties:
+- compatible: "cavium,octeon-6335-uctl"
+
+  Compatibility with all cn6XXX SOCs.
+
+- reg: The base address of the UCTL register bank.
+
+- #address-cells: Must be <2>.
+
+- #size-cells: Must be <2>.
+
+- ranges: Empty to signify direct mapping of the children.
+
+- refclk-frequency: A single cell containing the reference clock
+  frequency in Hz.
+
+- refclk-type: A string describing the reference clock connection
+  either "crystal" or "external".
+
+Example:
+	uctl@118006f000000 {
+		compatible = "cavium,octeon-6335-uctl";
+		reg = <0x11800 0x6f000000 0x0 0x100>;
+		ranges; /* Direct mapping */
+		#address-cells = <2>;
+		#size-cells = <2>;
+		/* 12MHz, 24MHz and 48MHz allowed */
+		refclk-frequency = <24000000>;
+		/* Either "crystal" or "external" */
+		refclk-type = "crystal";
+
+		ehci@16f0000000000 {
+			compatible = "cavium,octeon-6335-ehci","usb-ehci";
+			reg = <0x16f00 0x00000000 0x0 0x100>;
+			interrupts = <0 56>;
+			big-endian-regs;
+		};
+		ohci@16f0000000400 {
+			compatible = "cavium,octeon-6335-ohci","usb-ohci";
+			reg = <0x16f00 0x00000400 0x0 0x100>;
+			interrupts = <0 56>;
+			big-endian-regs;
+		};
+	};
diff --git a/Bindings/mips/cpus.yaml b/Bindings/mips/cpus.yaml
new file mode 100644
index 0000000..cf382de
--- /dev/null
+++ b/Bindings/mips/cpus.yaml
@@ -0,0 +1,115 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/cpus.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MIPS CPUs
+
+maintainers:
+  - Thomas Bogendoerfer <tsbogend@alpha.franken.de>
+  - 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
+
+description: |
+  The device tree allows to describe the layout of CPUs in a system through
+  the "cpus" node, which in turn contains a number of subnodes (ie "cpu")
+  defining properties for every CPU.
+
+properties:
+  compatible:
+    enum:
+      - brcm,bmips3300
+      - brcm,bmips4350
+      - brcm,bmips4380
+      - brcm,bmips5000
+      - brcm,bmips5200
+      - ingenic,xburst-mxu1.0
+      - ingenic,xburst-fpu1.0-mxu1.1
+      - ingenic,xburst-fpu2.0-mxu2.0
+      - ingenic,xburst2-fpu2.1-mxu2.1-smt
+      - loongson,gs264
+      - mips,m14Kc
+      - mips,mips4Kc
+      - mips,mips4KEc
+      - mips,mips24Kc
+      - mips,mips24KEc
+      - mips,mips74Kc
+      - mips,mips1004Kc
+      - mti,interaptiv
+      - mti,mips24KEc
+      - mti,mips14KEc
+      - mti,mips14Kc
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  device_type: true
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - ingenic,xburst-mxu1.0
+              - ingenic,xburst-fpu1.0-mxu1.1
+              - ingenic,xburst-fpu2.0-mxu2.0
+              - ingenic,xburst2-fpu2.1-mxu2.1-smt
+    then:
+      required:
+        - device_type
+        - clocks
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    cpus {
+      #size-cells = <0>;
+      #address-cells = <1>;
+
+      cpu@0 {
+        compatible = "mips,mips1004Kc";
+        device_type = "cpu";
+        reg = <0>;
+      };
+
+      cpu@1 {
+        compatible = "mips,mips1004Kc";
+        device_type = "cpu";
+        reg = <1>;
+      };
+    };
+
+  - |
+    // Example 2 (Ingenic CPU)
+    #include <dt-bindings/clock/ingenic,jz4780-cgu.h>
+
+    cpus {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      cpu@0 {
+        compatible = "ingenic,xburst-fpu1.0-mxu1.1";
+        device_type = "cpu";
+        reg = <0>;
+
+        clocks = <&cgu JZ4780_CLK_CPU>;
+      };
+
+      cpu@1 {
+        compatible = "ingenic,xburst-fpu1.0-mxu1.1";
+        device_type = "cpu";
+        reg = <1>;
+
+        clocks = <&cgu JZ4780_CLK_CORE1>;
+      };
+    };
+...
diff --git a/Bindings/mips/img/pistachio-marduk.txt b/Bindings/mips/img/pistachio-marduk.txt
new file mode 100644
index 0000000..2d5126d
--- /dev/null
+++ b/Bindings/mips/img/pistachio-marduk.txt
@@ -0,0 +1,10 @@
+Imagination Technologies' Pistachio SoC based Marduk Board
+==========================================================
+
+Compatible string must be "img,pistachio-marduk", "img,pistachio"
+
+Hardware and other related documentation is available at
+https://docs.creatordev.io/ci40/
+
+It is also known as Creator Ci40. Marduk is legacy name and will
+be there for decades.
diff --git a/Bindings/mips/img/pistachio.txt b/Bindings/mips/img/pistachio.txt
new file mode 100644
index 0000000..a736d88
--- /dev/null
+++ b/Bindings/mips/img/pistachio.txt
@@ -0,0 +1,42 @@
+Imagination Pistachio SoC
+=========================
+
+Required properties:
+--------------------
+ - compatible: Must include "img,pistachio".
+
+CPU nodes:
+----------
+A "cpus" node is required.  Required properties:
+ - #address-cells: Must be 1.
+ - #size-cells: Must be 0.
+A CPU sub-node is also required for at least CPU 0.  Since the topology may
+be probed via CPS, it is not necessary to specify secondary CPUs.  Required
+propertis:
+ - device_type: Must be "cpu".
+ - compatible: Must be "mti,interaptiv".
+ - reg: CPU number.
+ - clocks: Must include the CPU clock.  See ../../clock/clock-bindings.txt for
+   details on clock bindings.
+Example:
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "mti,interaptiv";
+			reg = <0>;
+			clocks = <&clk_core CLK_MIPS>;
+		};
+	};
+
+
+Boot protocol:
+--------------
+In accordance with the MIPS UHI specification[1], the bootloader must pass the
+following arguments to the kernel:
+ - $a0: -2.
+ - $a1: KSEG0 address of the flattened device-tree blob.
+
+[1] http://prplfoundation.org/wiki/MIPS_documentation
diff --git a/Bindings/mips/img/xilfpga.txt b/Bindings/mips/img/xilfpga.txt
new file mode 100644
index 0000000..57e7ee9
--- /dev/null
+++ b/Bindings/mips/img/xilfpga.txt
@@ -0,0 +1,83 @@
+Imagination University Program MIPSfpga
+=======================================
+
+Under the Imagination University Program, a microAptiv UP core has been
+released for academic usage.
+
+As we are dealing with a MIPS core instantiated on an FPGA, specifications
+are fluid and can be varied in RTL.
+
+This binding document is provided as baseline guidance for the example
+project provided by IMG.
+
+The example project runs on the Nexys4DDR board by Digilent powered by
+the ARTIX-7 FPGA by Xilinx.
+
+Relevant details about the example project and the Nexys4DDR board:
+
+- microAptiv UP core m14Kc
+- 50MHz clock speed
+- 128Mbyte DDR RAM	at 0x0000_0000
+- 8Kbyte RAM		at 0x1000_0000
+- axi_intc		at 0x1020_0000
+- axi_uart16550		at 0x1040_0000
+- axi_gpio		at 0x1060_0000
+- axi_i2c		at 0x10A0_0000
+- custom_gpio		at 0x10C0_0000
+- axi_ethernetlite	at 0x10E0_0000
+- 8Kbyte BootRAM	at 0x1FC0_0000
+
+Required properties:
+--------------------
+ - compatible: Must include "digilent,nexys4ddr","img,xilfpga".
+
+CPU nodes:
+----------
+A "cpus" node is required.  Required properties:
+ - #address-cells: Must be 1.
+ - #size-cells: Must be 0.
+A CPU sub-node is also required for at least CPU 0. Required properties:
+ - device_type: Must be "cpu".
+ - compatible: Must be "mips,m14Kc".
+ - reg: Must be <0>.
+ - clocks: phandle to ext clock for fixed-clock received by MIPS core.
+
+Example:
+
+	compatible = "img,xilfpga","digilent,nexys4ddr";
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "mips,m14Kc";
+			reg = <0>;
+			clocks	= <&ext>;
+		};
+	};
+
+	ext: ext {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+	};
+
+Boot protocol:
+--------------
+
+The BootRAM is a writeable "RAM" in FPGA at 0x1FC0_0000.
+This is for easy reprogrammibility via JTAG.
+
+The BootRAM initializes the cache and the axi_uart peripheral.
+
+DDR initialization is already handled by a HW IP block.
+
+When the example project bitstream is loaded, the cpu_reset button
+needs to be pressed.
+
+The bootram initializes the cache and axi_uart.
+Then outputs MIPSFPGA\n\r on the serial port on the Nexys4DDR board.
+
+At this point, the board is ready to load the Linux kernel
+vmlinux file via JTAG.
diff --git a/Bindings/mips/ingenic/devices.yaml b/Bindings/mips/ingenic/devices.yaml
new file mode 100644
index 0000000..f2e822a
--- /dev/null
+++ b/Bindings/mips/ingenic/devices.yaml
@@ -0,0 +1,58 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/ingenic/devices.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic XBurst based Platforms
+
+maintainers:
+  - 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
+
+description:
+  Devices with a Ingenic XBurst CPU shall have the following properties.
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+
+      - description: Qi Hardware Ben NanoNote
+        items:
+          - const: qi,lb60
+          - const: ingenic,jz4740
+
+      - description: YLM RetroMini RS-90
+        items:
+          - const: ylm,rs90
+          - const: ingenic,jz4725b
+
+      - description: Game Consoles Worldwide GCW Zero
+        items:
+          - const: gcw,zero
+          - const: ingenic,jz4770
+
+      - description: MIPS Creator CI20
+        items:
+          - const: img,ci20
+          - const: ingenic,jz4780
+
+      - description: YSH & ATIL General Board, CU1000 Module with Neo Backplane
+        items:
+          - const: yna,cu1000-neo
+          - const: ingenic,x1000e
+
+      - description: YSH & ATIL General Board, CU1830 Module with Neo Backplane
+        items:
+          - const: yna,cu1830-neo
+          - const: ingenic,x1830
+
+      - description: YSH & ATIL General Board, CU2000 Module with Neo Backplane
+        items:
+          - const: yna,cu2000-neo
+          - const: ingenic,x2000e
+
+additionalProperties: true
+
+...
diff --git a/Bindings/mips/lantiq/fpi-bus.txt b/Bindings/mips/lantiq/fpi-bus.txt
new file mode 100644
index 0000000..0a2df43
--- /dev/null
+++ b/Bindings/mips/lantiq/fpi-bus.txt
@@ -0,0 +1,31 @@
+Lantiq XWAY SoC FPI BUS binding
+============================
+
+
+-------------------------------------------------------------------------------
+Required properties:
+- compatible			: Should be one of
+					"lantiq,xrx200-fpi"
+- reg				: The address and length of the XBAR
+				  configuration register.
+				  Address and length of the FPI bus itself.
+- lantiq,rcu			: A phandle to the RCU syscon
+- lantiq,offset-endianness	: Offset of the endianness configuration
+				  register
+
+-------------------------------------------------------------------------------
+Example for the FPI on the xrx200 SoCs:
+	fpi@10000000 {
+		compatible = "lantiq,xrx200-fpi";
+		ranges = <0x0 0x10000000 0xf000000>;
+		reg =	<0x1f400000 0x1000>,
+			<0x10000000 0xf000000>;
+		lantiq,rcu = <&rcu0>;
+		lantiq,offset-endianness = <0x4c>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		gptu@e100a00 {
+			......
+		};
+	};
diff --git a/Bindings/mips/lantiq/lantiq,cgu.yaml b/Bindings/mips/lantiq/lantiq,cgu.yaml
new file mode 100644
index 0000000..d580572
--- /dev/null
+++ b/Bindings/mips/lantiq/lantiq,cgu.yaml
@@ -0,0 +1,32 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/lantiq/lantiq,cgu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lantiq Xway SoC series Clock Generation Unit (CGU)
+
+maintainers:
+  - John Crispin <john@phrozen.org>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - lantiq,cgu-xway
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    cgu@103000 {
+        compatible = "lantiq,cgu-xway";
+        reg = <0x103000 0x1000>;
+    };
diff --git a/Bindings/mips/lantiq/lantiq,dma-xway.yaml b/Bindings/mips/lantiq/lantiq,dma-xway.yaml
new file mode 100644
index 0000000..15d41bd
--- /dev/null
+++ b/Bindings/mips/lantiq/lantiq,dma-xway.yaml
@@ -0,0 +1,32 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/lantiq/lantiq,dma-xway.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lantiq Xway SoCs DMA Controller
+
+maintainers:
+  - John Crispin <john@phrozen.org>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - lantiq,dma-xway
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    dma@e104100 {
+        compatible = "lantiq,dma-xway";
+        reg = <0xe104100 0x800>;
+    };
diff --git a/Bindings/mips/lantiq/lantiq,ebu.yaml b/Bindings/mips/lantiq/lantiq,ebu.yaml
new file mode 100644
index 0000000..0fada1f
--- /dev/null
+++ b/Bindings/mips/lantiq/lantiq,ebu.yaml
@@ -0,0 +1,32 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/lantiq/lantiq,ebu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lantiq Xway SoC series External Bus Unit (EBU)
+
+maintainers:
+  - John Crispin <john@phrozen.org>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - lantiq,ebu-xway
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    ebu@105300 {
+        compatible = "lantiq,ebu-xway";
+        reg = <0x105300 0x100>;
+    };
diff --git a/Bindings/mips/lantiq/lantiq,pmu.yaml b/Bindings/mips/lantiq/lantiq,pmu.yaml
new file mode 100644
index 0000000..4982b45
--- /dev/null
+++ b/Bindings/mips/lantiq/lantiq,pmu.yaml
@@ -0,0 +1,32 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/lantiq/lantiq,pmu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lantiq Xway SoC series Power Management Unit (PMU)
+
+maintainers:
+  - John Crispin <john@phrozen.org>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - lantiq,pmu-xway
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    pmu@102000 {
+        compatible = "lantiq,pmu-xway";
+        reg = <0x102000 0x1000>;
+    };
diff --git a/Bindings/mips/lantiq/rcu.txt b/Bindings/mips/lantiq/rcu.txt
new file mode 100644
index 0000000..8ec6191
--- /dev/null
+++ b/Bindings/mips/lantiq/rcu.txt
@@ -0,0 +1,69 @@
+Lantiq XWAY SoC RCU binding
+===========================
+
+This binding describes the RCU (reset controller unit) multifunction device,
+where each sub-device has its own set of registers.
+
+The RCU register range is used for multiple purposes. Mostly one device
+uses one or multiple register exclusively, but for some registers some
+bits are for one driver and some other bits are for a different driver.
+With this patch all accesses to the RCU registers will go through
+syscon.
+
+
+-------------------------------------------------------------------------------
+Required properties:
+- compatible	: The first and second values must be:
+		  "lantiq,xrx200-rcu", "simple-mfd", "syscon"
+- reg		: The address and length of the system control registers
+
+
+-------------------------------------------------------------------------------
+Example of the RCU bindings on a xRX200 SoC:
+	rcu0: rcu@203000 {
+		compatible = "lantiq,xrx200-rcu", "simple-mfd", "syscon";
+		reg = <0x203000 0x100>;
+		ranges = <0x0 0x203000 0x100>;
+		big-endian;
+
+		reset0: reset-controller@10 {
+			compatible = "lantiq,xrx200-reset";
+			reg = <0x10 4>, <0x14 4>;
+
+			#reset-cells = <2>;
+		};
+
+		reset1: reset-controller@48 {
+			compatible = "lantiq,xrx200-reset";
+			reg = <0x48 4>, <0x24 4>;
+
+			#reset-cells = <2>;
+		};
+
+		usb_phy0: usb2-phy@18 {
+			compatible = "lantiq,xrx200-usb2-phy";
+			reg = <0x18 4>, <0x38 4>;
+
+			resets = <&reset1 4 4>, <&reset0 4 4>;
+			reset-names = "phy", "ctrl";
+			#phy-cells = <0>;
+		};
+
+		usb_phy1: usb2-phy@34 {
+			compatible = "lantiq,xrx200-usb2-phy";
+			reg = <0x34 4>, <0x3C 4>;
+
+			resets = <&reset1 5 4>, <&reset0 4 4>;
+			reset-names = "phy", "ctrl";
+			#phy-cells = <0>;
+		};
+
+		reboot@10 {
+			compatible = "syscon-reboot";
+			reg = <0x10 4>;
+
+			regmap = <&rcu0>;
+			offset = <0x10>;
+			mask = <0x40000000>;
+		};
+	};
diff --git a/Bindings/mips/loongson/devices.yaml b/Bindings/mips/loongson/devices.yaml
new file mode 100644
index 0000000..099e40e
--- /dev/null
+++ b/Bindings/mips/loongson/devices.yaml
@@ -0,0 +1,54 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/loongson/devices.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Loongson based Platforms
+
+maintainers:
+  - Jiaxun Yang <jiaxun.yang@flygoat.com>
+description: |
+  Devices with a Loongson CPU shall have the following properties.
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+
+      - description: Classic Loongson64 Quad Core + LS7A
+        items:
+          - const: loongson,loongson64c-4core-ls7a
+
+      - description: Classic Loongson64 Quad Core + RS780E
+        items:
+          - const: loongson,loongson64c-4core-rs780e
+
+      - description: Classic Loongson64 Octa Core + RS780E
+        items:
+          - const: loongson,loongson64c-8core-rs780e
+
+      - description: Generic Loongson64 Quad Core + LS7A
+        items:
+          - const: loongson,loongson64g-4core-ls7a
+
+      - description: Virtual Loongson64 Quad Core + VirtIO
+        items:
+          - const: loongson,loongson64v-4core-virtio
+
+      - description: LS1B based boards
+        items:
+          - enum:
+              - loongson,lsgz-1b-dev
+          - const: loongson,ls1b
+
+      - description: LS1C based boards
+        items:
+          - enum:
+              - loongmasses,smartloong-1c
+          - const: loongson,ls1c
+
+additionalProperties: true
+
+...
diff --git a/Bindings/mips/loongson/ls2k-reset.yaml b/Bindings/mips/loongson/ls2k-reset.yaml
new file mode 100644
index 0000000..358ac8c
--- /dev/null
+++ b/Bindings/mips/loongson/ls2k-reset.yaml
@@ -0,0 +1,38 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/loongson/ls2k-reset.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Loongson 2K1000 PM Controller
+
+maintainers:
+  - Qing Zhang <zhangqing@loongson.cn>
+
+description: |
+  This controller can be found in Loongson-2K1000 Soc systems.
+
+properties:
+  compatible:
+    const: loongson,ls2k-pm
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+        pm: reset-controller@1fe07000 {
+            compatible = "loongson,ls2k-pm";
+            reg = <0 0x1fe07000 0 0x422>;
+        };
+    };
+...
diff --git a/Bindings/mips/loongson/rs780e-acpi.yaml b/Bindings/mips/loongson/rs780e-acpi.yaml
new file mode 100644
index 0000000..3e3a370
--- /dev/null
+++ b/Bindings/mips/loongson/rs780e-acpi.yaml
@@ -0,0 +1,42 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/loongson/rs780e-acpi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Loongson RS780E PCH ACPI Controller
+
+maintainers:
+  - Jiaxun Yang <jiaxun.yang@flygoat.com>
+
+description: |
+  This controller can be found in Loongson-3 systems with RS780E PCH.
+
+properties:
+  compatible:
+    const: loongson,rs780e-acpi
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    isa@0 {
+      compatible = "isa";
+      #address-cells = <2>;
+      #size-cells = <1>;
+      ranges = <1 0 0 0x1000>;
+
+      acpi@800 {
+        compatible = "loongson,rs780e-acpi";
+        reg = <1 0x800 0x100>;
+      };
+    };
+
+...
diff --git a/Bindings/mips/mscc.txt b/Bindings/mips/mscc.txt
new file mode 100644
index 0000000..cc916ea
--- /dev/null
+++ b/Bindings/mips/mscc.txt
@@ -0,0 +1,59 @@
+* Microsemi MIPS CPUs
+
+Boards with a SoC of the Microsemi MIPS family shall have the following
+properties:
+
+Required properties:
+- compatible: "mscc,ocelot", "mscc,luton", "mscc,serval" or "mscc,jr2"
+
+
+* Other peripherals:
+
+o CPU chip regs:
+
+The SoC has a few registers (DEVCPU_GCB:CHIP_REGS) handling miscellaneous
+functionalities: chip ID, general purpose register for software use, reset
+controller, hardware status and configuration, efuses.
+
+Required properties:
+- compatible: Should be "mscc,ocelot-chip-regs", "simple-mfd", "syscon"
+- reg : Should contain registers location and length
+
+Example:
+	syscon@71070000 {
+		compatible = "mscc,ocelot-chip-regs", "simple-mfd", "syscon";
+		reg = <0x71070000 0x1c>;
+	};
+
+
+o CPU system control:
+
+The SoC has a few registers (ICPU_CFG:CPU_SYSTEM_CTRL) handling configuration of
+the CPU: 8 general purpose registers, reset control, CPU en/disabling, CPU
+endianness, CPU bus control, CPU status.
+
+Required properties:
+- compatible: Should be "mscc,ocelot-cpu-syscon", "syscon"
+- reg : Should contain registers location and length
+
+Example:
+	syscon@70000000 {
+		compatible = "mscc,ocelot-cpu-syscon", "syscon";
+		reg = <0x70000000 0x2c>;
+	};
+
+o HSIO regs:
+
+The SoC has a few registers (HSIO) handling miscellaneous functionalities:
+configuration and status of PLL5, RCOMP, SyncE, SerDes configurations and
+status, SerDes muxing and a thermal sensor.
+
+Required properties:
+- compatible: Should be "mscc,ocelot-hsio", "syscon", "simple-mfd"
+- reg : Should contain registers location and length
+
+Example:
+	syscon@10d0000 {
+		compatible = "mscc,ocelot-hsio", "syscon", "simple-mfd";
+		reg = <0x10d0000 0x10000>;
+	};
diff --git a/Bindings/mips/ni.txt b/Bindings/mips/ni.txt
new file mode 100644
index 0000000..722bf2d
--- /dev/null
+++ b/Bindings/mips/ni.txt
@@ -0,0 +1,7 @@
+National Instruments MIPS platforms
+
+required root node properties:
+	- compatible: must be "ni,169445"
+
+CPU Nodes
+	- compatible: must be "mti,mips14KEc"
diff --git a/Bindings/mips/pic32/microchip,pic32mzda.txt b/Bindings/mips/pic32/microchip,pic32mzda.txt
new file mode 100644
index 0000000..1c8dbc4
--- /dev/null
+++ b/Bindings/mips/pic32/microchip,pic32mzda.txt
@@ -0,0 +1,31 @@
+* Microchip PIC32MZDA Platforms
+
+PIC32MZDA Starter Kit
+Required root node properties:
+    - compatible = "microchip,pic32mzda-sk", "microchip,pic32mzda"
+
+CPU nodes:
+----------
+A "cpus" node is required.  Required properties:
+ - #address-cells: Must be 1.
+ - #size-cells: Must be 0.
+A CPU sub-node is also required.  Required properties:
+ - device_type: Must be "cpu".
+ - compatible: Must be "mti,mips14KEc".
+Example:
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "mti,mips14KEc";
+		};
+	};
+
+Boot protocol
+--------------
+In accordance with Unified Hosting Interface Reference Manual (MD01069), the
+bootloader must pass the following arguments to the kernel:
+ - $a0: -2.
+ - $a1: KSEG0 address of the flattened device-tree blob.
diff --git a/Bindings/mips/ralink.yaml b/Bindings/mips/ralink.yaml
new file mode 100644
index 0000000..53c1f66
--- /dev/null
+++ b/Bindings/mips/ralink.yaml
@@ -0,0 +1,88 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/ralink.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ralink SoC based Platforms
+
+maintainers:
+  - Sergio Paracuellos <sergio.paracuellos@gmail.com>
+
+description: |
+    Boards with a Ralink SoC shall have the following properties.
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+      - description: Boards with Ralink RT2880 SoC
+        items:
+          - enum:
+              - ralink,rt2880-eval-board
+          - const: ralink,rt2880-soc
+
+      - description: Boards with Ralink RT3050 SoC
+        items:
+          - const: ralink,rt3050-soc
+
+      - description: Boards with Ralink RT3052 SoC
+        items:
+          - enum:
+              - ralink,rt3052-eval-board
+          - const: ralink,rt3052-soc
+
+      - description: Boards with Ralink RT3350 SoC
+        items:
+          - const: ralink,rt3350-soc
+
+      - description: Boards with Ralink RT3352 SoC
+        items:
+          - const: ralink,rt3352-soc
+
+      - description: Boards with Ralink RT3383 SoC
+        items:
+          - enum:
+              - ralink,rt3883-eval-board
+          - const: ralink,rt3383-soc
+
+      - description: Boards with Ralink RT5350 SoC
+        items:
+          - const: ralink,rt5350-soc
+
+      - description: Boards with Mediatek/Ralink MT7620A SoC
+        items:
+          - enum:
+              - ralink,mt7620a-eval-board
+          - const: ralink,mt7620a-soc
+
+      - description: Boards with Mediatek/Ralink MT7620N SoC
+        items:
+          - const: ralink,mt7620n-soc
+
+      - description: Boards with Mediatek/Ralink MT7628A SoC
+        items:
+          - enum:
+              - onion,omega2+
+              - vocore,vocore2
+          - const: ralink,mt7628a-soc
+
+      - description: Boards with Mediatek/Ralink MT7688A SoC
+        items:
+          - enum:
+              - gardena,smart-gateway-mt7688
+              - onion,omega2+
+          - const: ralink,mt7628a-soc
+
+      - description: Boards with Mediatek/Ralink MT7621 SoC
+        items:
+          - enum:
+              - gnubee,gb-pc1
+              - gnubee,gb-pc2
+              - tplink,hc220-g5-v1
+          - const: mediatek,mt7621-soc
+
+additionalProperties: true
+
+...
diff --git a/Bindings/mips/realtek-rtl.yaml b/Bindings/mips/realtek-rtl.yaml
new file mode 100644
index 0000000..f8ac309
--- /dev/null
+++ b/Bindings/mips/realtek-rtl.yaml
@@ -0,0 +1,24 @@
+# SPDX-License-Identifier: GPL-2.0-or-later OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mips/realtek-rtl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek RTL83xx/93xx SoC series
+
+maintainers:
+  - Bert Vermeulen <bert@biot.com>
+  - Sander Vanheule <sander@svanheule.net>
+
+properties:
+  $nodename:
+    const: "/"
+  compatible:
+    oneOf:
+      # RTL8382-based boards
+      - items:
+          - enum:
+              - cisco,sg220-26
+          - const: realtek,rtl8382-soc
+
+additionalProperties: true