diff --git a/Bindings/memory-controllers/st,stm32-fmc2-ebi-props.yaml b/Bindings/memory-controllers/st,stm32-fmc2-ebi-props.yaml
new file mode 100644
index 0000000..475e409
--- /dev/null
+++ b/Bindings/memory-controllers/st,stm32-fmc2-ebi-props.yaml
@@ -0,0 +1,144 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi-props.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Peripheral properties for ST FMC2 Controller
+
+maintainers:
+  - Christophe Kerello <christophe.kerello@foss.st.com>
+  - Marek Vasut <marex@denx.de>
+
+properties:
+  st,fmc2-ebi-cs-transaction-type:
+    description: |
+      Select one of the transactions type supported
+      0: Asynchronous mode 1 SRAM/FRAM.
+      1: Asynchronous mode 1 PSRAM.
+      2: Asynchronous mode A SRAM/FRAM.
+      3: Asynchronous mode A PSRAM.
+      4: Asynchronous mode 2 NOR.
+      5: Asynchronous mode B NOR.
+      6: Asynchronous mode C NOR.
+      7: Asynchronous mode D NOR.
+      8: Synchronous read synchronous write PSRAM.
+      9: Synchronous read asynchronous write PSRAM.
+      10: Synchronous read synchronous write NOR.
+      11: Synchronous read asynchronous write NOR.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 11
+
+  st,fmc2-ebi-cs-cclk-enable:
+    description: Continuous clock enable (first bank must be configured
+      in synchronous mode). The FMC_CLK is generated continuously
+      during asynchronous and synchronous access. By default, the
+      FMC_CLK is only generated during synchronous access.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-mux-enable:
+    description: Address/Data multiplexed on databus (valid only with
+      NOR and PSRAM transactions type). By default, Address/Data
+      are not multiplexed.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-buswidth:
+    description: Data bus width
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 8, 16 ]
+    default: 16
+
+  st,fmc2-ebi-cs-waitpol-high:
+    description: Wait signal polarity (NWAIT signal active high).
+      By default, NWAIT is active low.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-waitcfg-enable:
+    description: The NWAIT signal indicates wheither the data from the
+      device are valid or if a wait state must be inserted when accessing
+      the device in synchronous mode. By default, the NWAIT signal is
+      active one data cycle before wait state.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-wait-enable:
+    description: The NWAIT signal is enabled (its level is taken into
+      account after the programmed latency period to insert wait states
+      if asserted). By default, the NWAIT signal is disabled.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-asyncwait-enable:
+    description: The NWAIT signal is taken into account during asynchronous
+      transactions. By default, the NWAIT signal is not taken into account
+      during asynchronous transactions.
+    $ref: /schemas/types.yaml#/definitions/flag
+
+  st,fmc2-ebi-cs-cpsize:
+    description: CRAM page size. The controller splits the burst access
+      when the memory page is reached. By default, no burst split when
+      crossing page boundary.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 0, 128, 256, 512, 1024 ]
+    default: 0
+
+  st,fmc2-ebi-cs-byte-lane-setup-ns:
+    description: This property configures the byte lane setup timing
+      defined in nanoseconds from NBLx low to Chip Select NEx low.
+
+  st,fmc2-ebi-cs-address-setup-ns:
+    description: This property defines the duration of the address setup
+      phase in nanoseconds used for asynchronous read/write transactions.
+
+  st,fmc2-ebi-cs-address-hold-ns:
+    description: This property defines the duration of the address hold
+      phase in nanoseconds used for asynchronous multiplexed read/write
+      transactions.
+
+  st,fmc2-ebi-cs-data-setup-ns:
+    description: This property defines the duration of the data setup phase
+      in nanoseconds used for asynchronous read/write transactions.
+
+  st,fmc2-ebi-cs-bus-turnaround-ns:
+    description: This property defines the delay in nanoseconds between the
+      end of current read/write transaction and the next transaction.
+
+  st,fmc2-ebi-cs-data-hold-ns:
+    description: This property defines the duration of the data hold phase
+      in nanoseconds used for asynchronous read/write transactions.
+
+  st,fmc2-ebi-cs-clk-period-ns:
+    description: This property defines the FMC_CLK output signal period in
+      nanoseconds.
+
+  st,fmc2-ebi-cs-data-latency-ns:
+    description: This property defines the data latency before reading or
+      writing the first data in nanoseconds.
+
+  st,fmc2-ebi-cs-write-address-setup-ns:
+    description: This property defines the duration of the address setup
+      phase in nanoseconds used for asynchronous write transactions.
+
+  st,fmc2-ebi-cs-write-address-hold-ns:
+    description: This property defines the duration of the address hold
+      phase in nanoseconds used for asynchronous multiplexed write
+      transactions.
+
+  st,fmc2-ebi-cs-write-data-setup-ns:
+    description: This property defines the duration of the data setup
+      phase in nanoseconds used for asynchronous write transactions.
+
+  st,fmc2-ebi-cs-write-bus-turnaround-ns:
+    description: This property defines the delay between the end of current
+      write transaction and the next transaction in nanoseconds.
+
+  st,fmc2-ebi-cs-write-data-hold-ns:
+    description: This property defines the duration of the data hold phase
+      in nanoseconds used for asynchronous write transactions.
+
+  st,fmc2-ebi-cs-max-low-pulse-ns:
+    description: This property defines the maximum chip select low pulse
+      duration in nanoseconds for synchronous transactions. When this timing
+      reaches 0, the controller splits the current access, toggles NE to
+      allow device refresh and restarts a new access.
+
+additionalProperties: true