diff --git a/Bindings/display/bridge/adi,adv7511.yaml b/Bindings/display/bridge/adi,adv7511.yaml
new file mode 100644
index 0000000..5bbe818
--- /dev/null
+++ b/Bindings/display/bridge/adi,adv7511.yaml
@@ -0,0 +1,237 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/adi,adv7511.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7511/11W/13 HDMI Encoders
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+description: |
+  The ADV7511, ADV7511W and ADV7513 are HDMI audio and video
+  transmitters compatible with HDMI 1.4 and DVI 1.0. They support color
+  space conversion, S/PDIF, CEC and HDCP. The transmitter input is
+  parallel RGB or YUV data.
+
+properties:
+  compatible:
+    enum:
+      - adi,adv7511
+      - adi,adv7511w
+      - adi,adv7513
+
+  reg:
+    description: |
+      I2C slave addresses.
+
+      The ADV7511/11W/13 internal registers are split into four pages
+      exposed through different I2C addresses, creating four register
+      maps. Each map has it own I2C address and acts as a standard slave
+      device on the I2C bus. The main address is mandatory, others are
+      optional and revert to defaults if not specified.
+    minItems: 1
+    maxItems: 4
+
+  reg-names:
+    description:
+      Names of maps with programmable addresses. It can contain any map
+      needing a non-default address.
+    minItems: 1
+    items:
+      - const: main
+      - const: edid
+      - const: cec
+      - const: packet
+
+  clocks:
+    description: Reference to the CEC clock.
+    maxItems: 1
+
+  clock-names:
+    const: cec
+
+  interrupts:
+    maxItems: 1
+
+  pd-gpios:
+    description: GPIO connected to the power down signal.
+    maxItems: 1
+
+  avdd-supply:
+    description: A 1.8V supply that powers up the AVDD pin.
+
+  dvdd-supply:
+    description: A 1.8V supply that powers up the DVDD pin.
+
+  pvdd-supply:
+    description: A 1.8V supply that powers up the PVDD pin.
+
+  dvdd-3v-supply:
+    description: A 3.3V supply that powers up the DVDD_3V pin.
+
+  bgvdd-supply:
+    description: A 1.8V supply that powers up the BGVDD pin.
+
+  adi,input-depth:
+    description: Number of bits per color component at the input.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 8, 10, 12 ]
+
+  adi,input-colorspace:
+    description: Input color space.
+    enum: [ rgb, yuv422, yuv444 ]
+
+  adi,input-clock:
+    description: |
+      Input clock type.
+        "1x": one clock cycle per pixel
+        "2x": two clock cycles per pixel
+        "dd": one clock cycle per pixel, data driven on both edges
+    enum: [ 1x, 2x, dd ]
+
+  adi,clock-delay:
+    description:
+      Video data clock delay relative to the pixel clock, in ps
+      (-1200ps .. 1600 ps).
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
+
+  adi,embedded-sync:
+    description:
+      If defined, the input uses synchronization signals embedded in the
+      data stream (similar to BT.656).
+    type: boolean
+
+  adi,input-style:
+    description:
+      Input components arrangement variant as listed in the input
+      format tables in the datasheet.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 1, 2, 3 ]
+
+  adi,input-justification:
+    description: Input bit justification.
+    enum: [ left, evenly, right ]
+
+  ports:
+    description:
+      The ADV7511(W)/13 has two video ports and one audio port.
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        description: Video port for the RGB or YUV input.
+        $ref: /schemas/graph.yaml#/properties/port
+
+      port@1:
+        description: Video port for the HDMI output.
+        $ref: /schemas/graph.yaml#/properties/port
+
+      port@2:
+        description: Audio port for the HDMI output.
+        $ref: /schemas/graph.yaml#/properties/port
+
+# adi,input-colorspace and adi,input-clock are required except in
+# "rgb 1x" and "yuv444 1x" modes, in which case they must not be
+# specified.
+if:
+  not:
+    properties:
+      adi,input-colorspace:
+        contains:
+          enum: [ rgb, yuv444 ]
+      adi,input-clock:
+        contains:
+          const: 1x
+
+then:
+  required:
+    - adi,input-style
+    - adi,input-justification
+
+else:
+  properties:
+    adi,input-style: false
+    adi,input-justification: false
+
+
+required:
+  - compatible
+  - reg
+  - ports
+  - adi,input-depth
+  - adi,input-colorspace
+  - adi,input-clock
+  - avdd-supply
+  - dvdd-supply
+  - pvdd-supply
+  - dvdd-3v-supply
+  - bgvdd-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c@e6500000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        reg = <0 0xe6500000>;
+
+        adv7511w: hdmi@39 {
+            compatible = "adi,adv7511w";
+            /*
+             * The EDID page will be accessible on address 0x66 on the I2C
+             * bus. All other maps continue to use their default addresses.
+             */
+            reg = <0x39>, <0x66>;
+            reg-names = "main", "edid";
+            interrupt-parent = <&gpio3>;
+            interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+            clocks = <&cec_clock>;
+            clock-names = "cec";
+            avdd-supply = <&v1v8>;
+            dvdd-supply = <&v1v8>;
+            pvdd-supply = <&v1v8>;
+            dvdd-3v-supply = <&v3v3>;
+            bgvdd-supply = <&v1v8>;
+
+            adi,input-depth = <8>;
+            adi,input-colorspace = "yuv422";
+            adi,input-clock = "1x";
+
+            adi,input-style = <3>;
+            adi,input-justification = "right";
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    adv7511w_in: endpoint {
+                        remote-endpoint = <&dpi_out>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    adv7511_out: endpoint {
+                        remote-endpoint = <&hdmi_connector_in>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+                    codec_endpoint: endpoint {
+                        remote-endpoint = <&i2s0_cpu_endpoint>;
+                    };
+                };
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/adi,adv7533.yaml b/Bindings/display/bridge/adi,adv7533.yaml
new file mode 100644
index 0000000..df20a3c
--- /dev/null
+++ b/Bindings/display/bridge/adi,adv7533.yaml
@@ -0,0 +1,188 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/adi,adv7533.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analog Devices ADV7533/35 HDMI Encoders
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart@ideasonboard.com>
+
+allOf:
+  - $ref: /schemas/sound/dai-common.yaml#
+
+description: |
+  The ADV7533 and ADV7535 are HDMI audio and video transmitters
+  compatible with HDMI 1.4 and DVI 1.0. They support color space
+  conversion, S/PDIF, CEC and HDCP. The transmitter input is MIPI DSI.
+
+properties:
+  compatible:
+    enum:
+      - adi,adv7533
+      - adi,adv7535
+
+  reg:
+    description: |
+      I2C slave addresses.
+
+      The ADV7533/35 internal registers are split into four pages
+      exposed through different I2C addresses, creating four register
+      maps. Each map has it own I2C address and acts as a standard slave
+      device on the I2C bus. The main address is mandatory, others are
+      optional and revert to defaults if not specified.
+    minItems: 1
+    maxItems: 4
+
+  reg-names:
+    description:
+      Names of maps with programmable addresses. It can contain any map
+      needing a non-default address.
+    minItems: 1
+    items:
+      - const: main
+      - const: edid
+      - const: cec
+      - const: packet
+
+  clocks:
+    description: Reference to the CEC clock.
+    maxItems: 1
+
+  clock-names:
+    const: cec
+
+  interrupts:
+    maxItems: 1
+
+  pd-gpios:
+    description: GPIO connected to the power down signal.
+    maxItems: 1
+
+  avdd-supply:
+    description: A 1.8V supply that powers up the AVDD pin.
+
+  dvdd-supply:
+    description: A 1.8V supply that powers up the DVDD pin.
+
+  pvdd-supply:
+    description: A 1.8V supply that powers up the PVDD pin.
+
+  a2vdd-supply:
+    description: A 1.8V supply that powers up the A2VDD pin.
+
+  v3p3-supply:
+    description: A 3.3V supply that powers up the V3P3 pin.
+
+  v1p2-supply:
+    description:
+      A supply that powers up the V1P2 pin. It can be either 1.2V
+      or 1.8V for ADV7533 but only 1.8V for ADV7535.
+
+  adi,disable-timing-generator:
+    description:
+      Disables the internal timing generator. The chip will rely on the
+      sync signals in the DSI data lanes, rather than generating its own
+      timings for HDMI output.
+    type: boolean
+
+  adi,dsi-lanes:
+    description: Number of DSI data lanes connected to the DSI host.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [ 1, 2, 3, 4 ]
+
+  "#sound-dai-cells":
+    const: 0
+
+  ports:
+    description:
+      The ADV7533/35 has two video ports and one audio port.
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        description:
+          Video port for the DSI input. The remote endpoint phandle
+          should be a reference to a valid mipi_dsi_host_device.
+        $ref: /schemas/graph.yaml#/properties/port
+
+      port@1:
+        description: Video port for the HDMI output.
+        $ref: /schemas/graph.yaml#/properties/port
+
+      port@2:
+        description: Audio port for the HDMI output.
+        $ref: /schemas/graph.yaml#/properties/port
+
+required:
+  - compatible
+  - reg
+  - ports
+  - adi,dsi-lanes
+  - avdd-supply
+  - dvdd-supply
+  - pvdd-supply
+  - a2vdd-supply
+  - v3p3-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c@e6500000 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        reg = <0 0xe6500000>;
+
+        adv7533: hdmi@39 {
+            compatible = "adi,adv7533";
+            /*
+             * The EDID page will be accessible on address 0x66 on the I2C
+             * bus. All other maps continue to use their default addresses.
+             */
+            reg = <0x39>, <0x66>;
+            reg-names = "main", "edid";
+            interrupt-parent = <&gpio3>;
+            interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+            clocks = <&cec_clock>;
+            clock-names = "cec";
+            adi,dsi-lanes = <4>;
+            avdd-supply = <&v1v8>;
+            dvdd-supply = <&v1v8>;
+            pvdd-supply = <&v1v8>;
+            a2vdd-supply = <&v1v8>;
+            v3p3-supply = <&v3v3>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    adv7533_in: endpoint {
+                        remote-endpoint = <&dsi_out>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    adv7533_out: endpoint {
+                        remote-endpoint = <&hdmi_connector_in>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+                    codec_endpoint: endpoint {
+                        remote-endpoint = <&i2s0_cpu_endpoint>;
+                    };
+                };
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/analogix,anx7625.yaml b/Bindings/display/bridge/analogix,anx7625.yaml
new file mode 100644
index 0000000..a1ed100
--- /dev/null
+++ b/Bindings/display/bridge/analogix,anx7625.yaml
@@ -0,0 +1,187 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+# Copyright 2019 Analogix Semiconductor, Inc.
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/analogix,anx7625.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analogix ANX7625 SlimPort (4K Mobile HD Transmitter)
+
+maintainers:
+  - Xin Ji <xji@analogixsemi.com>
+
+description: |
+  The ANX7625 is an ultra-low power 4K Mobile HD Transmitter
+  designed for portable devices.
+
+properties:
+  compatible:
+    const: analogix,anx7625
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    description: used for interrupt pin B8.
+    maxItems: 1
+
+  enable-gpios:
+    description: used for power on chip control, POWER_EN pin D2.
+    maxItems: 1
+
+  reset-gpios:
+    description: used for reset chip control, RESET_N pin B7.
+    maxItems: 1
+
+  vdd10-supply:
+    description: Regulator that provides the supply 1.0V power.
+
+  vdd18-supply:
+    description: Regulator that provides the supply 1.8V power.
+
+  vdd33-supply:
+    description: Regulator that provides the supply 3.3V power.
+
+  analogix,lane0-swing:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    minItems: 1
+    maxItems: 20
+    description:
+      an array of swing register setting for DP tx lane0 PHY.
+      Registers 0~9 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0,
+      Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2,
+      Swing1_Pre2, Swing0_Pre3, they are for [Boost control] and
+      [Swing control] setting.
+      Registers 0~9, bit 3:0 is [Boost control], these bits control
+      post cursor manual, increase the [Boost control] to increase
+      Pre-emphasis value.
+      Registers 0~9, bit 6:4 is [Swing control], these bits control
+      swing manual, increase [Swing control] setting to add Vp-p value
+      for each Swing, Pre.
+      Registers 10~19 are Swing0_Pre0, Swing1_Pre0, Swing2_Pre0,
+      Swing3_Pre0, Swing0_Pre1, Swing1_Pre1, Swing2_Pre1, Swing0_Pre2,
+      Swing1_Pre2, Swing0_Pre3, they are for [R select control] and
+      [R Termination control] setting.
+      Registers 10~19, bit 4:0 is [R select control], these bits are
+      compensation manual, increase it can enhance IO driven strength
+      and Vp-p.
+      Registers 10~19, bit 5:6 is [R termination control], these bits
+      adjust 50ohm impedance of DP tx termination. 00:55 ohm,
+      01:50 ohm(default), 10:45 ohm, 11:40 ohm.
+
+  analogix,lane1-swing:
+    $ref: /schemas/types.yaml#/definitions/uint8-array
+    minItems: 1
+    maxItems: 20
+    description:
+      an array of swing register setting for DP tx lane1 PHY.
+      DP TX lane1 swing register setting same with lane0
+      swing, please refer lane0-swing property description.
+
+  analogix,audio-enable:
+    type: boolean
+    description: let the driver enable audio HDMI codec function or not.
+
+  aux-bus:
+    $ref: /schemas/display/dp-aux-bus.yaml#
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          MIPI DSI/DPI input.
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            type: object
+            additionalProperties: false
+
+            properties:
+              remote-endpoint: true
+
+              bus-type:
+                enum: [7]
+                default: 1
+
+              data-lanes: true
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for panel or connector.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - vdd10-supply
+  - vdd18-supply
+  - vdd33-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        encoder@58 {
+            compatible = "analogix,anx7625";
+            reg = <0x58>;
+            enable-gpios = <&pio 45 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&pio 73 GPIO_ACTIVE_HIGH>;
+            vdd10-supply = <&pp1000_mipibrdg>;
+            vdd18-supply = <&pp1800_mipibrdg>;
+            vdd33-supply = <&pp3300_mipibrdg>;
+            analogix,audio-enable;
+            analogix,lane0-swing = /bits/ 8 <0x14 0x54 0x64 0x74>;
+            analogix,lane1-swing = /bits/ 8 <0x14 0x54 0x64 0x74>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                mipi2dp_bridge_in: port@0 {
+                    reg = <0>;
+                    anx7625_in: endpoint {
+                        remote-endpoint = <&mipi_dsi>;
+                        bus-type = <7>;
+                        data-lanes = <0 1 2 3>;
+                    };
+                };
+
+                mipi2dp_bridge_out: port@1 {
+                    reg = <1>;
+                    anx7625_out: endpoint {
+                        remote-endpoint = <&panel_in>;
+                    };
+                };
+            };
+
+            aux-bus {
+                panel {
+                    compatible = "innolux,n125hce-gn1";
+                    power-supply = <&pp3300_disp_x>;
+                    backlight = <&backlight_lcd0>;
+
+                    port {
+                        panel_in: endpoint {
+                            remote-endpoint = <&anx7625_out>;
+                        };
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/analogix,anx7814.yaml b/Bindings/display/bridge/analogix,anx7814.yaml
new file mode 100644
index 0000000..4509c49
--- /dev/null
+++ b/Bindings/display/bridge/analogix,anx7814.yaml
@@ -0,0 +1,109 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/analogix,anx7814.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analogix ANX7814 SlimPort (Full-HD Transmitter)
+
+maintainers:
+  - Andrzej Hajda <andrzej.hajda@intel.com>
+  - Neil Armstrong <neil.armstrong@linaro.org>
+  - Robert Foss <robert.foss@linaro.org>
+
+properties:
+  compatible:
+    enum:
+      - analogix,anx7808
+      - analogix,anx7812
+      - analogix,anx7814
+      - analogix,anx7816
+      - analogix,anx7818
+
+  reg:
+    maxItems: 1
+    description: I2C address of the device.
+
+  interrupts:
+    maxItems: 1
+    description: Should contain the INTP interrupt.
+
+  hpd-gpios:
+    deprecated: true
+    maxItems: 1
+    description: Which GPIO to use for hpd.
+
+  pd-gpios:
+    maxItems: 1
+    description: Which GPIO to use for power down.
+
+  reset-gpios:
+    maxItems: 1
+    description: Which GPIO to use for reset.
+
+  dvdd10-supply:
+    description: Regulator for 1.0V digital core power.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for HDMI input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for SlimPort, DisplayPort, eDP or MyDP output.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        anx7814: bridge@38 {
+            compatible = "analogix,anx7814";
+            reg = <0x38>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <99 IRQ_TYPE_LEVEL_LOW>;   /* INTP */
+            pd-gpios = <&pio 33 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&pio 98 GPIO_ACTIVE_HIGH>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    anx7814_in: endpoint {
+                        remote-endpoint = <&hdmi0_out>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    anx7814_out: endpoint {
+                        remote-endpoint = <&edp_out>;
+                    };
+                };
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/analogix,dp.yaml b/Bindings/display/bridge/analogix,dp.yaml
new file mode 100644
index 0000000..62f0521
--- /dev/null
+++ b/Bindings/display/bridge/analogix,dp.yaml
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/analogix,dp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analogix Display Port bridge
+
+maintainers:
+  - Rob Herring <robh@kernel.org>
+
+properties:
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks: true
+
+  clock-names: true
+
+  phys: true
+
+  phy-names:
+    const: dp
+
+  force-hpd:
+    type: boolean
+    description:
+      Indicate driver need force hpd when hpd detect failed, this
+      is used for some eDP screen which don not have a hpd signal.
+
+  hpd-gpios:
+    description:
+      Hotplug detect GPIO.
+      Indicates which GPIO should be used for hotplug detection
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Input node to receive pixel data.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Port node with one endpoint connected to a dp-connector node.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - reg
+  - interrupts
+  - clock-names
+  - clocks
+  - ports
+
+additionalProperties: true
diff --git a/Bindings/display/bridge/anx6345.yaml b/Bindings/display/bridge/anx6345.yaml
new file mode 100644
index 0000000..514f588
--- /dev/null
+++ b/Bindings/display/bridge/anx6345.yaml
@@ -0,0 +1,94 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/anx6345.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Analogix ANX6345 eDP Transmitter
+
+maintainers:
+  - Torsten Duwe <duwe@lst.de>
+
+description: |
+  The ANX6345 is an ultra-low power Full-HD eDP transmitter designed for
+  portable devices.
+
+properties:
+  compatible:
+    const: analogix,anx6345
+
+  reg:
+    maxItems: 1
+    description: base I2C address of the device
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active low reset
+
+  dvdd12-supply:
+    description: Regulator for 1.2V digital core power.
+
+  dvdd25-supply:
+    description: Regulator for 2.5V digital core power.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for LVTTL input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for eDP output (panel or connector).
+          May be omitted if EDID works reliably.
+
+    required:
+      - port@0
+
+required:
+  - compatible
+  - reg
+  - reset-gpios
+  - dvdd12-supply
+  - dvdd25-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      anx6345: anx6345@38 {
+        compatible = "analogix,anx6345";
+        reg = <0x38>;
+        reset-gpios = <&pio42 1 /* GPIO_ACTIVE_LOW */>;
+        dvdd25-supply = <&reg_dldo2>;
+        dvdd12-supply = <&reg_fldo1>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          anx6345_in: port@0 {
+            reg = <0>;
+            anx6345_in_tcon0: endpoint {
+              remote-endpoint = <&tcon0_out_anx6345>;
+            };
+          };
+
+          anx6345_out: port@1 {
+            reg = <1>;
+            anx6345_out_panel: endpoint {
+              remote-endpoint = <&panel_in_edp>;
+            };
+          };
+        };
+      };
+    };
diff --git a/Bindings/display/bridge/cdns,dsi.yaml b/Bindings/display/bridge/cdns,dsi.yaml
new file mode 100644
index 0000000..2306032
--- /dev/null
+++ b/Bindings/display/bridge/cdns,dsi.yaml
@@ -0,0 +1,180 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/cdns,dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence DSI bridge
+
+maintainers:
+  - Boris Brezillon <boris.brezillon@bootlin.com>
+
+description: |
+   CDNS DSI is a bridge device which converts DPI to DSI
+
+properties:
+  compatible:
+    enum:
+      - cdns,dsi
+      - ti,j721e-dsi
+
+  reg:
+    minItems: 1
+    items:
+      - description:
+          Register block for controller's registers.
+      - description:
+          Register block for wrapper settings registers in case of TI J7 SoCs.
+
+  clocks:
+    items:
+      - description: PSM clock, used by the IP
+      - description: sys clock, used by the IP
+
+  clock-names:
+    items:
+      - const: dsi_p_clk
+      - const: dsi_sys_clk
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: dphy
+
+  interrupts:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: dsi_p_rst
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Output port representing the DSI output. It can have
+          at most 4 endpoints. The endpoint number is directly encoding
+          the DSI virtual channel used by this device.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Input port representing the DPI input.
+
+    required:
+      - port@1
+
+allOf:
+  - $ref: ../dsi-controller.yaml#
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ti,j721e-dsi
+    then:
+      properties:
+        reg:
+          minItems: 2
+          maxItems: 2
+        power-domains:
+          maxItems: 1
+    else:
+      properties:
+        reg:
+          maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+  - phys
+  - phy-names
+  - ports
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        dsi@fd0c0000 {
+            compatible = "cdns,dsi";
+            reg = <0x0 0xfd0c0000 0x0 0x1000>;
+            clocks = <&pclk>, <&sysclk>;
+            clock-names = "dsi_p_clk", "dsi_sys_clk";
+            interrupts = <1>;
+            phys = <&dphy0>;
+            phy-names = "dphy";
+
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@1 {
+                    reg = <1>;
+                    endpoint {
+                        remote-endpoint = <&xxx_dpi_output>;
+                    };
+                };
+            };
+
+            panel@0 {
+                compatible = "panasonic,vvx10f034n00";
+                reg = <0>;
+                power-supply = <&vcc_lcd_reg>;
+            };
+        };
+    };
+
+  - |
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        dsi@fd0c0000 {
+            compatible = "cdns,dsi";
+            reg = <0x0 0xfd0c0000 0x0 0x1000>;
+            clocks = <&pclk>, <&sysclk>;
+            clock-names = "dsi_p_clk", "dsi_sys_clk";
+            interrupts = <1>;
+            phys = <&dphy1>;
+            phy-names = "dphy";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    endpoint@0 {
+                        reg = <0>;
+                        remote-endpoint = <&dsi_panel_input>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    endpoint {
+                        remote-endpoint = <&xxx_dpi_output>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/cdns,mhdp8546.yaml b/Bindings/display/bridge/cdns,mhdp8546.yaml
new file mode 100644
index 0000000..c2b3694
--- /dev/null
+++ b/Bindings/display/bridge/cdns,mhdp8546.yaml
@@ -0,0 +1,164 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/cdns,mhdp8546.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cadence MHDP8546 bridge
+
+maintainers:
+  - Swapnil Jakhade <sjakhade@cadence.com>
+  - Yuti Amonkar <yamonkar@cadence.com>
+
+properties:
+  compatible:
+    enum:
+      - cdns,mhdp8546
+      - ti,j721e-mhdp8546
+
+  reg:
+    minItems: 1
+    items:
+      - description:
+          Register block of mhdptx apb registers up to PHY mapped area (AUX_CONFIG_P).
+          The AUX and PMA registers are not part of this range, they are instead
+          included in the associated PHY.
+      - description:
+          Register block for DSS_EDP0_INTG_CFG_VP registers in case of TI J7 SoCs.
+      - description:
+          Register block of mhdptx sapb registers.
+
+  reg-names:
+    minItems: 1
+    items:
+      - const: mhdptx
+      - const: j721e-intg
+      - const: mhdptx-sapb
+
+  clocks:
+    maxItems: 1
+    description:
+      DP bridge clock, used by the IP to know how to translate a number of
+      clock cycles into a time (which is used to comply with DP standard timings
+      and delays).
+
+  phys:
+    maxItems: 1
+    description:
+      phandle to the DisplayPort PHY.
+
+  phy-names:
+    items:
+      - const: dpphy
+
+  power-domains:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          First input port representing the DP bridge input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Second input port representing the DP bridge input.
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Third input port representing the DP bridge input.
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Fourth input port representing the DP bridge input.
+
+      port@4:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Output port representing the DP bridge output.
+
+    required:
+      - port@0
+      - port@4
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ti,j721e-mhdp8546
+    then:
+      properties:
+        reg:
+          minItems: 2
+          maxItems: 3
+        reg-names:
+          minItems: 2
+          maxItems: 3
+    else:
+      properties:
+        reg:
+          minItems: 1
+          maxItems: 2
+        reg-names:
+          minItems: 1
+          maxItems: 2
+
+required:
+  - compatible
+  - clocks
+  - reg
+  - reg-names
+  - phys
+  - phy-names
+  - interrupts
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    bus {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        mhdp: dp-bridge@f0fb000000 {
+            compatible = "cdns,mhdp8546";
+            reg = <0xf0 0xfb000000 0x0 0x1000000>;
+            reg-names = "mhdptx";
+            clocks = <&mhdp_clock>;
+            phys = <&dp_phy>;
+            phy-names = "dpphy";
+            interrupts = <GIC_SPI 614 IRQ_TYPE_LEVEL_HIGH>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    dp_bridge_input: endpoint {
+                        remote-endpoint = <&xxx_dpi_output>;
+                    };
+                };
+
+                port@4 {
+                    reg = <4>;
+                    dp_bridge_output: endpoint {
+                        remote-endpoint = <&xxx_dp_connector_input>;
+                    };
+                };
+            };
+        };
+    };
+...
diff --git a/Bindings/display/bridge/chipone,icn6211.yaml b/Bindings/display/bridge/chipone,icn6211.yaml
new file mode 100644
index 0000000..5fb5437
--- /dev/null
+++ b/Bindings/display/bridge/chipone,icn6211.yaml
@@ -0,0 +1,123 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/chipone,icn6211.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Chipone ICN6211 MIPI-DSI to RGB Converter bridge
+
+maintainers:
+  - Jagan Teki <jagan@amarulasolutions.com>
+
+description: |
+  ICN6211 is MIPI-DSI to RGB Converter bridge from chipone.
+
+  It has a flexible configuration of MIPI DSI signal input and
+  produce RGB565, RGB666, RGB888 output format.
+
+properties:
+  compatible:
+    enum:
+      - chipone,icn6211
+
+  reg:
+    maxItems: 1
+    description: virtual channel number of a DSI peripheral
+
+  clock-names:
+    const: refclk
+
+  clocks:
+    maxItems: 1
+    description: |
+        Optional external clock connected to REF_CLK input.
+        The clock rate must be in 10..154 MHz range.
+
+  enable-gpios:
+    description: Bridge EN pin, chip is reset when EN is low.
+
+  vdd1-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the MIPI RX.
+
+  vdd2-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the PLL.
+
+  vdd3-supply:
+    description: A 1.8V/2.5V/3.3V supply that power the RGB output.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Video port for MIPI DSI input
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                description: array of physical DSI data lane indexes.
+                minItems: 1
+                items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DPI output (panel or connector).
+
+    required:
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - enable-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    dsi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@0 {
+        compatible = "chipone,icn6211";
+        reg = <0>;
+        enable-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* LCD-RST: PL5 */
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+
+            bridge_in_dsi: endpoint {
+              remote-endpoint = <&dsi_out_bridge>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+
+            bridge_out_panel: endpoint {
+              remote-endpoint = <&panel_out_bridge>;
+            };
+          };
+        };
+      };
+    };
diff --git a/Bindings/display/bridge/chrontel,ch7033.yaml b/Bindings/display/bridge/chrontel,ch7033.yaml
new file mode 100644
index 0000000..b0589fa
--- /dev/null
+++ b/Bindings/display/bridge/chrontel,ch7033.yaml
@@ -0,0 +1,77 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2019,2020 Lubomir Rintel <lkundrak@v3.sk>
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/chrontel,ch7033.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Chrontel CH7033 Video Encoder
+
+maintainers:
+  - Lubomir Rintel <lkundrak@v3.sk>
+
+properties:
+  compatible:
+    const: chrontel,ch7033
+
+  reg:
+    maxItems: 1
+    description: I2C address of the device
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+          Video port for RGB input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+          DVI port, should be connected to a node compatible with the
+          dvi-connector binding.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        vga-dvi-encoder@76 {
+            compatible = "chrontel,ch7033";
+            reg = <0x76>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    endpoint {
+                        remote-endpoint = <&lcd0_rgb_out>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    endpoint {
+                        remote-endpoint = <&dvi_in>;
+                    };
+                };
+
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/fsl,imx8qxp-ldb.yaml b/Bindings/display/bridge/fsl,imx8qxp-ldb.yaml
new file mode 100644
index 0000000..9454300
--- /dev/null
+++ b/Bindings/display/bridge/fsl,imx8qxp-ldb.yaml
@@ -0,0 +1,173 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/fsl,imx8qxp-ldb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX8qm/qxp LVDS Display Bridge
+
+maintainers:
+  - Liu Ying <victor.liu@nxp.com>
+
+description: |
+  The Freescale i.MX8qm/qxp LVDS Display Bridge(LDB) has two channels.
+
+  The i.MX8qm/qxp LDB is controlled by Control and Status Registers(CSR) module.
+  The CSR module, as a system controller, contains the LDB's configuration
+  registers.
+
+  For i.MX8qxp LDB, each channel supports up to 24bpp parallel input color
+  format and can map the input to VESA or JEIDA standards.  The two channels
+  cannot be used simultaneously, that is to say, the user should pick one of
+  them to use.  Two LDB channels from two LDB instances can work together in
+  LDB split mode to support a dual link LVDS display.  The channel indexes
+  have to be different.  Channel0 outputs odd pixels and channel1 outputs
+  even pixels.
+
+  For i.MX8qm LDB, each channel additionally supports up to 30bpp parallel
+  input color format.  The two channels can be used simultaneously, either
+  in dual mode or split mode.  In dual mode, the two channels output identical
+  data.  In split mode, channel0 outputs odd pixels and channel1 outputs even
+  pixels.
+
+  A side note is that i.MX8qm/qxp LDB is officially called pixel mapper in
+  the SoC reference manuals.  The pixel mapper uses logic of LDBs embedded in
+  i.MX6qdl/sx SoCs, i.e., it is essentially based on them.  To keep the naming
+  consistency, this binding calls it LDB.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8qm-ldb
+      - fsl,imx8qxp-ldb
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  clocks:
+    items:
+      - description: pixel clock
+      - description: bypass clock
+
+  clock-names:
+    items:
+      - const: pixel
+      - const: bypass
+
+  power-domains:
+    maxItems: 1
+
+  fsl,companion-ldb:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: |
+      A phandle which points to companion LDB which is used in LDB split mode.
+
+patternProperties:
+  "^channel@[0-1]$":
+    type: object
+    description: Represents a channel of LDB.
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      reg:
+        description: The channel index.
+        enum: [ 0, 1 ]
+
+      phys:
+        description: A phandle to the phy module representing the LVDS PHY.
+        maxItems: 1
+
+      phy-names:
+        const: lvds_phy
+
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input port of the channel.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Output port of the channel.
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+      - reg
+      - phys
+      - phy-names
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - "#address-cells"
+  - "#size-cells"
+  - clocks
+  - clock-names
+  - power-domains
+  - channel@0
+  - channel@1
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,imx8qm-ldb
+    then:
+      properties:
+        fsl,companion-ldb: false
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/firmware/imx/rsrc.h>
+    ldb {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        compatible = "fsl,imx8qxp-ldb";
+        clocks = <&clk IMX_SC_R_LVDS_0 IMX_SC_PM_CLK_MISC2>,
+                 <&clk IMX_SC_R_LVDS_0 IMX_SC_PM_CLK_BYPASS>;
+        clock-names = "pixel", "bypass";
+        power-domains = <&pd IMX_SC_R_LVDS_0>;
+
+        channel@0 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            reg = <0>;
+            phys = <&mipi_lvds_0_phy>;
+            phy-names = "lvds_phy";
+
+            port@0 {
+                reg = <0>;
+
+                mipi_lvds_0_ldb_ch0_mipi_lvds_0_pxl2dpi: endpoint {
+                    remote-endpoint = <&mipi_lvds_0_pxl2dpi_mipi_lvds_0_ldb_ch0>;
+                };
+            };
+        };
+
+        channel@1 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            reg = <1>;
+            phys = <&mipi_lvds_0_phy>;
+            phy-names = "lvds_phy";
+
+            port@0 {
+                reg = <0>;
+
+                mipi_lvds_0_ldb_ch1_mipi_lvds_0_pxl2dpi: endpoint {
+                    remote-endpoint = <&mipi_lvds_0_pxl2dpi_mipi_lvds_0_ldb_ch1>;
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/fsl,imx8qxp-pixel-combiner.yaml b/Bindings/display/bridge/fsl,imx8qxp-pixel-combiner.yaml
new file mode 100644
index 0000000..50bae21
--- /dev/null
+++ b/Bindings/display/bridge/fsl,imx8qxp-pixel-combiner.yaml
@@ -0,0 +1,144 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/fsl,imx8qxp-pixel-combiner.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX8qm/qxp Pixel Combiner
+
+maintainers:
+  - Liu Ying <victor.liu@nxp.com>
+
+description: |
+  The Freescale i.MX8qm/qxp Pixel Combiner takes two output streams from a
+  single display controller and manipulates the two streams to support a number
+  of modes(bypass, pixel combine, YUV444 to YUV422, split_RGB) configured as
+  either one screen, two screens, or virtual screens.  The pixel combiner is
+  also responsible for generating some of the control signals for the pixel link
+  output channel.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8qm-pixel-combiner
+      - fsl,imx8qxp-pixel-combiner
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: apb
+
+  power-domains:
+    maxItems: 1
+
+patternProperties:
+  "^channel@[0-1]$":
+    type: object
+    description: Represents a display stream of pixel combiner.
+
+    properties:
+      "#address-cells":
+        const: 1
+
+      "#size-cells":
+        const: 0
+
+      reg:
+        description: The display stream index.
+        enum: [ 0, 1 ]
+
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input endpoint of the display stream.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Output endpoint of the display stream.
+
+    required:
+      - "#address-cells"
+      - "#size-cells"
+      - reg
+      - port@0
+      - port@1
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - "#address-cells"
+  - "#size-cells"
+  - reg
+  - clocks
+  - clock-names
+  - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx8-lpcg.h>
+    #include <dt-bindings/firmware/imx/rsrc.h>
+    pixel-combiner@56020000 {
+        compatible = "fsl,imx8qxp-pixel-combiner";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <0x56020000 0x10000>;
+        clocks = <&dc0_pixel_combiner_lpcg IMX_LPCG_CLK_4>;
+        clock-names = "apb";
+        power-domains = <&pd IMX_SC_R_DC_0>;
+
+        channel@0 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            reg = <0>;
+
+            port@0 {
+                reg = <0>;
+
+                dc0_pixel_combiner_ch0_dc0_dpu_disp0: endpoint {
+                    remote-endpoint = <&dc0_dpu_disp0_dc0_pixel_combiner_ch0>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+
+                dc0_pixel_combiner_ch0_dc0_pixel_link0: endpoint {
+                    remote-endpoint = <&dc0_pixel_link0_dc0_pixel_combiner_ch0>;
+                };
+            };
+        };
+
+        channel@1 {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            reg = <1>;
+
+            port@0 {
+                reg = <0>;
+
+                dc0_pixel_combiner_ch1_dc0_dpu_disp1: endpoint {
+                    remote-endpoint = <&dc0_dpu_disp1_dc0_pixel_combiner_ch1>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+
+                dc0_pixel_combiner_ch1_dc0_pixel_link1: endpoint {
+                    remote-endpoint = <&dc0_pixel_link1_dc0_pixel_combiner_ch1>;
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/fsl,imx8qxp-pixel-link.yaml b/Bindings/display/bridge/fsl,imx8qxp-pixel-link.yaml
new file mode 100644
index 0000000..38ecc79
--- /dev/null
+++ b/Bindings/display/bridge/fsl,imx8qxp-pixel-link.yaml
@@ -0,0 +1,144 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/fsl,imx8qxp-pixel-link.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX8qm/qxp Display Pixel Link
+
+maintainers:
+  - Liu Ying <victor.liu@nxp.com>
+
+description: |
+  The Freescale i.MX8qm/qxp Display Pixel Link(DPL) forms a standard
+  asynchronous linkage between pixel sources(display controller or
+  camera module) and pixel consumers(imaging or displays).
+  It consists of two distinct functions, a pixel transfer function and a
+  control interface.  Multiple pixel channels can exist per one control channel.
+  This binding documentation is only for pixel links whose pixel sources are
+  display controllers.
+
+  The i.MX8qm/qxp Display Pixel Link is accessed via System Controller Unit(SCU)
+  firmware.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx8qm-dc-pixel-link
+      - fsl,imx8qxp-dc-pixel-link
+
+  fsl,dc-id:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    description: |
+      u8 value representing the display controller index that the pixel link
+      connects to.
+
+  fsl,dc-stream-id:
+    $ref: /schemas/types.yaml#/definitions/uint8
+    description: |
+      u8 value representing the display controller stream index that the pixel
+      link connects to.
+    enum: [0, 1]
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: The pixel link input port node from upstream video source.
+
+    patternProperties:
+      "^port@[1-4]$":
+        $ref: /schemas/graph.yaml#/properties/port
+        description: The pixel link output port node to downstream bridge.
+
+    required:
+      - port@0
+      - port@1
+      - port@2
+      - port@3
+      - port@4
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,imx8qxp-dc-pixel-link
+    then:
+      properties:
+        fsl,dc-id:
+          const: 0
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: fsl,imx8qm-dc-pixel-link
+    then:
+      properties:
+        fsl,dc-id:
+          enum: [0, 1]
+
+required:
+  - compatible
+  - fsl,dc-id
+  - fsl,dc-stream-id
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    dc0-pixel-link0 {
+        compatible = "fsl,imx8qxp-dc-pixel-link";
+        fsl,dc-id = /bits/ 8 <0>;
+        fsl,dc-stream-id = /bits/ 8 <0>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            /* from dc0 pixel combiner channel0 */
+            port@0 {
+                reg = <0>;
+
+                dc0_pixel_link0_dc0_pixel_combiner_ch0: endpoint {
+                    remote-endpoint = <&dc0_pixel_combiner_ch0_dc0_pixel_link0>;
+                };
+            };
+
+            /* to PXL2DPIs in MIPI/LVDS combo subsystems */
+            port@1 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <1>;
+
+                dc0_pixel_link0_mipi_lvds_0_pxl2dpi: endpoint@0 {
+                    reg = <0>;
+                    remote-endpoint = <&mipi_lvds_0_pxl2dpi_dc0_pixel_link0>;
+                };
+
+                dc0_pixel_link0_mipi_lvds_1_pxl2dpi: endpoint@1 {
+                    reg = <1>;
+                    remote-endpoint = <&mipi_lvds_1_pxl2dpi_dc0_pixel_link0>;
+                };
+            };
+
+            /* unused */
+            port@2 {
+                reg = <2>;
+            };
+
+            /* unused */
+            port@3 {
+                reg = <3>;
+            };
+
+            /* to imaging subsystem */
+            port@4 {
+                reg = <4>;
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/fsl,imx8qxp-pxl2dpi.yaml b/Bindings/display/bridge/fsl,imx8qxp-pxl2dpi.yaml
new file mode 100644
index 0000000..e4e77fad
--- /dev/null
+++ b/Bindings/display/bridge/fsl,imx8qxp-pxl2dpi.yaml
@@ -0,0 +1,108 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/fsl,imx8qxp-pxl2dpi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX8qxp Pixel Link to Display Pixel Interface
+
+maintainers:
+  - Liu Ying <victor.liu@nxp.com>
+
+description: |
+  The Freescale i.MX8qxp Pixel Link to Display Pixel Interface(PXL2DPI)
+  interfaces the pixel link 36-bit data output and the DSI controller’s
+  MIPI-DPI 24-bit data input, and inputs of LVDS Display Bridge(LDB) module
+  used in LVDS mode, to remap the pixel color codings between those modules.
+  This module is purely combinatorial.
+
+  The i.MX8qxp PXL2DPI is controlled by Control and Status Registers(CSR) module.
+  The CSR module, as a system controller, contains the PXL2DPI's configuration
+  register.
+
+properties:
+  compatible:
+    const: fsl,imx8qxp-pxl2dpi
+
+  fsl,sc-resource:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: The SCU resource ID associated with this PXL2DPI instance.
+
+  power-domains:
+    maxItems: 1
+
+  fsl,companion-pxl2dpi:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: |
+      A phandle which points to companion PXL2DPI which is used by downstream
+      LVDS Display Bridge(LDB) in split mode.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: The PXL2DPI input port node from pixel link.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: The PXL2DPI output port node to downstream bridge.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - fsl,sc-resource
+  - power-domains
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/firmware/imx/rsrc.h>
+    pxl2dpi {
+        compatible = "fsl,imx8qxp-pxl2dpi";
+        fsl,sc-resource = <IMX_SC_R_MIPI_0>;
+        power-domains = <&pd IMX_SC_R_MIPI_0>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <0>;
+
+                mipi_lvds_0_pxl2dpi_dc_pixel_link0: endpoint@0 {
+                    reg = <0>;
+                    remote-endpoint = <&dc_pixel_link0_mipi_lvds_0_pxl2dpi>;
+                };
+
+                mipi_lvds_0_pxl2dpi_dc_pixel_link1: endpoint@1 {
+                     reg = <1>;
+                     remote-endpoint = <&dc_pixel_link1_mipi_lvds_0_pxl2dpi>;
+                };
+            };
+
+            port@1 {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                reg = <1>;
+
+                mipi_lvds_0_pxl2dpi_mipi_lvds_0_ldb_ch0: endpoint@0 {
+                    reg = <0>;
+                    remote-endpoint = <&mipi_lvds_0_ldb_ch0_mipi_lvds_0_pxl2dpi>;
+                };
+
+                mipi_lvds_0_pxl2dpi_mipi_lvds_0_ldb_ch1: endpoint@1 {
+                    reg = <1>;
+                    remote-endpoint = <&mipi_lvds_0_ldb_ch1_mipi_lvds_0_pxl2dpi>;
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/fsl,imx93-mipi-dsi.yaml b/Bindings/display/bridge/fsl,imx93-mipi-dsi.yaml
new file mode 100644
index 0000000..d6e51d0
--- /dev/null
+++ b/Bindings/display/bridge/fsl,imx93-mipi-dsi.yaml
@@ -0,0 +1,115 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/fsl,imx93-mipi-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX93 specific extensions to Synopsys Designware MIPI DSI
+
+maintainers:
+  - Liu Ying <victor.liu@nxp.com>
+
+description: |
+  There is a Synopsys Designware MIPI DSI Host Controller and a Synopsys
+  Designware MIPI DPHY embedded in Freescale i.MX93 SoC.  Some configurations
+  and extensions to them are controlled by i.MX93 media blk-ctrl.
+
+allOf:
+  - $ref: snps,dw-mipi-dsi.yaml#
+
+properties:
+  compatible:
+    const: fsl,imx93-mipi-dsi
+
+  clocks:
+    items:
+      - description: apb clock
+      - description: pixel clock
+      - description: PHY configuration clock
+      - description: PHY reference clock
+
+  clock-names:
+    items:
+      - const: pclk
+      - const: pix
+      - const: phy_cfg
+      - const: phy_ref
+
+  interrupts:
+    maxItems: 1
+
+  fsl,media-blk-ctrl:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      i.MX93 media blk-ctrl, as a syscon, controls pixel component bit map
+      configurations from LCDIF display controller to the MIPI DSI host
+      controller and MIPI DPHY PLL related configurations through PLL SoC
+      interface.
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - compatible
+  - interrupts
+  - fsl,media-blk-ctrl
+  - power-domains
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx93-clock.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/power/fsl,imx93-power.h>
+
+    dsi@4ae10000 {
+        compatible = "fsl,imx93-mipi-dsi";
+        reg = <0x4ae10000 0x10000>;
+        interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&clk IMX93_CLK_MIPI_DSI_GATE>,
+                 <&clk IMX93_CLK_MEDIA_DISP_PIX>,
+                 <&clk IMX93_CLK_MIPI_PHY_CFG>,
+                 <&clk IMX93_CLK_24M>;
+        clock-names = "pclk", "pix", "phy_cfg", "phy_ref";
+        fsl,media-blk-ctrl = <&media_blk_ctrl>;
+        power-domains = <&media_blk_ctrl IMX93_MEDIABLK_PD_MIPI_DSI>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        panel@0 {
+            compatible = "raydium,rm67191";
+            reg = <0>;
+            reset-gpios = <&adp5585gpio 6 GPIO_ACTIVE_LOW>;
+            dsi-lanes = <4>;
+            video-mode = <2>;
+
+            port {
+                panel_in: endpoint {
+                    remote-endpoint = <&dsi_out>;
+                };
+            };
+        };
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+
+                dsi_to_lcdif: endpoint {
+                    remote-endpoint = <&lcdif_to_dsi>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+
+                dsi_out: endpoint {
+                    remote-endpoint = <&panel_in>;
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/fsl,ldb.yaml b/Bindings/display/bridge/fsl,ldb.yaml
new file mode 100644
index 0000000..07388bf
--- /dev/null
+++ b/Bindings/display/bridge/fsl,ldb.yaml
@@ -0,0 +1,122 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/fsl,ldb.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX8MP DPI to LVDS bridge chip
+
+maintainers:
+  - Marek Vasut <marex@denx.de>
+
+description: |
+  The i.MX8MP mediamix contains two registers which are responsible
+  for configuring the on-SoC DPI-to-LVDS serializer. This describes
+  those registers as bridge within the DT.
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx6sx-ldb
+      - fsl,imx8mp-ldb
+      - fsl,imx93-ldb
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: ldb
+
+  reg:
+    maxItems: 2
+
+  reg-names:
+    items:
+      - const: ldb
+      - const: lvds
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for DPI input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS Channel-A output (panel or bridge).
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS Channel-B output (panel or bridge).
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - clocks
+  - ports
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - fsl,imx6sx-ldb
+              - fsl,imx93-ldb
+    then:
+      properties:
+        ports:
+          properties:
+            port@2: false
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx8mp-clock.h>
+
+    blk-ctrl {
+        #address-cells = <1>;
+        #size-cells = <1>;
+
+        bridge@5c {
+            compatible = "fsl,imx8mp-ldb";
+            clocks = <&clk IMX8MP_CLK_MEDIA_LDB>;
+            clock-names = "ldb";
+            reg = <0x5c 0x4>, <0x128 0x4>;
+            reg-names = "ldb", "lvds";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    ldb_from_lcdif2: endpoint {
+                        remote-endpoint = <&lcdif2_to_ldb>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+
+                    ldb_lvds_ch0: endpoint {
+                        remote-endpoint = <&ldb_to_lvdsx4panel>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+
+                    ldb_lvds_ch1: endpoint {
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/google,cros-ec-anx7688.yaml b/Bindings/display/bridge/google,cros-ec-anx7688.yaml
new file mode 100644
index 0000000..a44d025
--- /dev/null
+++ b/Bindings/display/bridge/google,cros-ec-anx7688.yaml
@@ -0,0 +1,80 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/google,cros-ec-anx7688.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ChromeOS EC ANX7688 HDMI to DP Converter through Type-C Port
+
+maintainers:
+  - Nicolas Boichat <drinkcat@chromium.org>
+
+description: |
+  ChromeOS EC ANX7688 is a display bridge that converts HDMI 2.0 to
+  DisplayPort 1.3 Ultra-HDi (4096x2160p60). It is an Analogix ANX7688 chip
+  which is connected to and operated by the ChromeOS Embedded Controller
+  (See google,cros-ec.yaml). It is accessed using I2C tunneling through
+  the EC and therefore its node should be a child of an EC I2C tunnel node
+  (See google,cros-ec-i2c-tunnel.yaml).
+
+properties:
+  compatible:
+    const: google,cros-ec-anx7688
+
+  reg:
+    maxItems: 1
+    description: I2C address of the device.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for HDMI input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: USB Type-c connector.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c_tunnel_b: i2c-tunnel1 {
+        compatible = "google,cros-ec-i2c-tunnel";
+        google,remote-bus = <1>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        anx7688: anx7688@2c {
+            compatible = "google,cros-ec-anx7688";
+            reg = <0x2c>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+                port@0 {
+                    reg = <0>;
+                    anx7688_in: endpoint {
+                        remote-endpoint = <&hdmi0_out>;
+                    };
+                };
+                port@1 {
+                    reg = <1>;
+                    anx7688_out: endpoint {
+                        remote-endpoint = <&typec_connector>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/ingenic,jz4780-hdmi.yaml b/Bindings/display/bridge/ingenic,jz4780-hdmi.yaml
new file mode 100644
index 0000000..0b27df4
--- /dev/null
+++ b/Bindings/display/bridge/ingenic,jz4780-hdmi.yaml
@@ -0,0 +1,81 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ingenic,jz4780-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Ingenic JZ4780 HDMI Transmitter
+
+maintainers:
+  - H. Nikolaus Schaller <hns@goldelico.com>
+
+description: |
+  The HDMI Transmitter in the Ingenic JZ4780 is a Synopsys DesignWare HDMI 1.4
+  TX controller IP with accompanying PHY IP.
+
+allOf:
+  - $ref: synopsys,dw-hdmi.yaml#
+
+properties:
+  compatible:
+    const: ingenic,jz4780-dw-hdmi
+
+  reg-io-width:
+    const: 4
+
+  clocks:
+    maxItems: 2
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input from LCD controller output.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Link to the HDMI connector.
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - ports
+  - reg-io-width
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/ingenic,jz4780-cgu.h>
+
+    hdmi: hdmi@10180000 {
+        compatible = "ingenic,jz4780-dw-hdmi";
+        reg = <0x10180000 0x8000>;
+        reg-io-width = <4>;
+        interrupt-parent = <&intc>;
+        interrupts = <3>;
+        clocks = <&cgu JZ4780_CLK_AHB0>, <&cgu JZ4780_CLK_HDMI>;
+        clock-names = "iahb", "isfr";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            hdmi_in: port@0 {
+                reg = <0>;
+                dw_hdmi_in: endpoint {
+                    remote-endpoint = <&jz4780_lcd_out>;
+                };
+            };
+            hdmi_out: port@1 {
+                reg = <1>;
+                dw_hdmi_out: endpoint {
+                    remote-endpoint = <&hdmi_con>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/intel,keembay-dsi.yaml b/Bindings/display/bridge/intel,keembay-dsi.yaml
new file mode 100644
index 0000000..958a073
--- /dev/null
+++ b/Bindings/display/bridge/intel,keembay-dsi.yaml
@@ -0,0 +1,93 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/intel,keembay-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intel Keem Bay mipi dsi controller
+
+maintainers:
+  - Anitha Chrisanthus <anitha.chrisanthus@intel.com>
+  - Edmond J Dea <edmund.j.dea@intel.com>
+
+properties:
+  compatible:
+    const: intel,keembay-dsi
+
+  reg:
+    items:
+      - description: MIPI registers range
+
+  reg-names:
+    items:
+      - const: mipi
+
+  clocks:
+    items:
+      - description: MIPI DSI clock
+      - description: MIPI DSI econfig clock
+      - description: MIPI DSI config clock
+
+  clock-names:
+    items:
+      - const: clk_mipi
+      - const: clk_mipi_ecfg
+      - const: clk_mipi_cfg
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: MIPI DSI input port.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: DSI output port.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - clock-names
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    mipi-dsi@20900000 {
+        compatible = "intel,keembay-dsi";
+        reg = <0x20900000 0x4000>;
+        reg-names = "mipi";
+        clocks = <&scmi_clk 0x86>,
+                 <&scmi_clk 0x88>,
+                 <&scmi_clk 0x89>;
+        clock-names = "clk_mipi", "clk_mipi_ecfg",
+                      "clk_mipi_cfg";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                dsi_in: endpoint {
+                    remote-endpoint = <&disp_out>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                dsi_out: endpoint {
+                    remote-endpoint = <&adv7535_input>;
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/ite,it6505.yaml b/Bindings/display/bridge/ite,it6505.yaml
new file mode 100644
index 0000000..c9a882e
--- /dev/null
+++ b/Bindings/display/bridge/ite,it6505.yaml
@@ -0,0 +1,150 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ite,it6505.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ITE it6505
+
+maintainers:
+  - Allen Chen <allen.chen@ite.com.tw>
+
+description: |
+  The IT6505 is a high-performance DisplayPort 1.1a transmitter,
+  fully compliant with DisplayPort 1.1a, HDCP 1.3 specifications.
+  The IT6505 supports color depth of up to 36 bits (12 bits/color)
+  and ensures robust transmission of high-quality uncompressed video
+  content, along with uncompressed and compressed digital audio content.
+
+  Aside from the various video output formats supported, the IT6505
+  also encodes and transmits up to 8 channels of I2S digital audio,
+  with sampling rate up to 192kHz and sample size up to 24 bits.
+  In addition, an S/PDIF input port takes in compressed audio of up to
+  192kHz frame rate.
+
+  Each IT6505 chip comes preprogrammed with an unique HDCP key,
+  in compliance with the HDCP 1.3 standard so as to provide secure
+  transmission of high-definition content. Users of the IT6505 need not
+  purchase any HDCP keys or ROMs.
+
+properties:
+  compatible:
+    const: ite,it6505
+
+  reg:
+    maxItems: 1
+
+  ovdd-supply:
+    description: I/O voltage
+
+  pwr18-supply:
+    description: core voltage
+
+  interrupts:
+    maxItems: 1
+    description: interrupt specifier of INT pin
+
+  reset-gpios:
+    maxItems: 1
+    description: gpio specifier of RESET pin
+
+  extcon:
+    maxItems: 1
+    description: extcon specifier for the Power Delivery
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: A port node pointing to DPI host port node
+
+        properties:
+          endpoint:
+            $ref: /schemas/graph.yaml#/$defs/endpoint-base
+            unevaluatedProperties: false
+
+            properties:
+              link-frequencies:
+                minItems: 1
+                maxItems: 1
+                description: Allowed max link frequencies in Hz
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: Video port for DP output
+
+        properties:
+          endpoint:
+            $ref: /schemas/graph.yaml#/$defs/endpoint-base
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                minItems: 1
+                uniqueItems: true
+                items:
+                  - enum: [ 0, 1 ]
+                  - const: 1
+                  - const: 2
+                  - const: 3
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - ovdd-supply
+  - pwr18-supply
+  - interrupts
+  - reset-gpios
+  - extcon
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        dp-bridge@5c {
+            compatible = "ite,it6505";
+            interrupts = <152 IRQ_TYPE_EDGE_FALLING 152 0>;
+            reg = <0x5c>;
+            pinctrl-names = "default";
+            pinctrl-0 = <&it6505_pins>;
+            ovdd-supply = <&mt6358_vsim1_reg>;
+            pwr18-supply = <&it6505_pp18_reg>;
+            reset-gpios = <&pio 179 1>;
+            extcon = <&usbc_extcon>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    it6505_in: endpoint {
+                        remote-endpoint = <&dpi_out>;
+                        link-frequencies = /bits/ 64 <150000000>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    it6505_out: endpoint {
+                        remote-endpoint = <&dp_in>;
+                        data-lanes = <0 1>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/ite,it66121.yaml b/Bindings/display/bridge/ite,it66121.yaml
new file mode 100644
index 0000000..a7eb260
--- /dev/null
+++ b/Bindings/display/bridge/ite,it66121.yaml
@@ -0,0 +1,129 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ite,it66121.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ITE it66121 HDMI bridge
+
+maintainers:
+  - Phong LE <ple@baylibre.com>
+  - Neil Armstrong <neil.armstrong@linaro.org>
+
+description: |
+  The IT66121 is a high-performance and low-power single channel HDMI
+  transmitter, fully compliant with HDMI 1.3a, HDCP 1.2 and backward compatible
+  to DVI 1.0 specifications.
+
+properties:
+  compatible:
+    enum:
+      - ite,it66121
+      - ite,it6610
+
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active low reset
+
+  vrf12-supply:
+    description: Regulator for 1.2V analog core power.
+
+  vcn33-supply:
+    description: Regulator for 3.3V digital core power.
+
+  vcn18-supply:
+    description: Regulator for 1.8V IO core power.
+
+  interrupts:
+    maxItems: 1
+
+  "#sound-dai-cells":
+    const: 0
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: DPI input port.
+
+        properties:
+          endpoint:
+            $ref: /schemas/graph.yaml#/$defs/endpoint-base
+            unevaluatedProperties: false
+
+            properties:
+              bus-width:
+                description:
+                  Endpoint bus width.
+                enum:
+                  - 12  # 12 data lines connected and dual-edge mode
+                  - 24  # 24 data lines connected and single-edge mode
+                default: 24
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: HDMI Connector port.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - reset-gpios
+  - vrf12-supply
+  - vcn33-supply
+  - vcn18-supply
+  - interrupts
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        it66121hdmitx: hdmitx@4c {
+            compatible = "ite,it66121";
+            pinctrl-names = "default";
+            pinctrl-0 = <&ite_pins_default>;
+            vcn33-supply = <&mt6358_vcn33_wifi_reg>;
+            vcn18-supply = <&mt6358_vcn18_reg>;
+            vrf12-supply = <&mt6358_vrf12_reg>;
+            reset-gpios = <&pio 160 GPIO_ACTIVE_LOW>;
+            interrupt-parent = <&pio>;
+            interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+            reg = <0x4c>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    it66121_in: endpoint {
+                        bus-width = <12>;
+                        remote-endpoint = <&display_out>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    hdmi_conn_out: endpoint {
+                        remote-endpoint = <&hdmi_conn_in>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/lontium,lt8912b.yaml b/Bindings/display/bridge/lontium,lt8912b.yaml
new file mode 100644
index 0000000..f201ae4
--- /dev/null
+++ b/Bindings/display/bridge/lontium,lt8912b.yaml
@@ -0,0 +1,103 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/lontium,lt8912b.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lontium LT8912B MIPI to HDMI Bridge
+
+maintainers:
+  - Adrien Grassein <adrien.grassein@gmail.com>
+
+description: |
+  The LT8912B is a bridge device which convert DSI to HDMI
+
+properties:
+  compatible:
+    enum:
+      - lontium,lt8912b
+
+  reg:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active high RESET pin.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Primary MIPI port for MIPI input
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes: true
+
+            required:
+              - data-lanes
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+          HDMI port, should be connected to a node compatible with the
+          hdmi-connector binding.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - reset-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      hdmi-bridge@48 {
+        compatible = "lontium,lt8912b";
+        reg = <0x48>;
+        reset-gpios = <&max7323 0 GPIO_ACTIVE_LOW>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+
+            hdmi_out_in: endpoint {
+              data-lanes = <0 1 2 3>;
+              remote-endpoint = <&mipi_dsi_out>;
+            };
+          };
+
+          port@1 {
+              reg = <1>;
+
+              endpoint {
+                  remote-endpoint = <&hdmi_in>;
+              };
+          };
+        };
+      };
+    };
+
+...
diff --git a/Bindings/display/bridge/lontium,lt9211.yaml b/Bindings/display/bridge/lontium,lt9211.yaml
new file mode 100644
index 0000000..9a6e9b2
--- /dev/null
+++ b/Bindings/display/bridge/lontium,lt9211.yaml
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/lontium,lt9211.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lontium LT9211 DSI/LVDS/DPI to DSI/LVDS/DPI bridge.
+
+maintainers:
+  - Marek Vasut <marex@denx.de>
+
+description: |
+  The LT9211 are bridge devices which convert Single/Dual-Link DSI/LVDS
+  or Single DPI to Single/Dual-Link DSI/LVDS or Single DPI.
+
+properties:
+  compatible:
+    enum:
+      - lontium,lt9211
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active high RESET pin.
+
+  vccio-supply:
+    description: Regulator for 1.8V IO power.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Primary MIPI DSI port-1 for MIPI input or
+          LVDS port-1 for LVDS input or DPI input.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Additional MIPI port-2 for MIPI input or LVDS port-2
+          for LVDS input. Used in combination with primary
+          port-1 to drive higher resolution displays
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Primary MIPI DSI port-1 for MIPI output or
+          LVDS port-1 for LVDS output or DPI output.
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Additional MIPI port-2 for MIPI output or LVDS port-2
+          for LVDS output. Used in combination with primary
+          port-1 to drive higher resolution displays.
+
+    required:
+      - port@0
+      - port@2
+
+required:
+  - compatible
+  - reg
+  - vccio-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      hdmi-bridge@3b {
+        compatible = "lontium,lt9211";
+        reg = <0x3b>;
+
+        reset-gpios = <&tlmm 128 GPIO_ACTIVE_HIGH>;
+        interrupts-extended = <&tlmm 84 IRQ_TYPE_EDGE_FALLING>;
+
+        vccio-supply = <&lt9211_1v8>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+
+            endpoint {
+              remote-endpoint = <&dsi0_out>;
+            };
+          };
+
+          port@2 {
+            reg = <2>;
+
+            endpoint {
+              remote-endpoint = <&panel_in_lvds>;
+            };
+          };
+        };
+      };
+    };
+
+...
diff --git a/Bindings/display/bridge/lontium,lt9611.yaml b/Bindings/display/bridge/lontium,lt9611.yaml
new file mode 100644
index 0000000..5b9d36f
--- /dev/null
+++ b/Bindings/display/bridge/lontium,lt9611.yaml
@@ -0,0 +1,121 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/lontium,lt9611.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Lontium LT9611(UXC) 2 Port MIPI to HDMI Bridge
+
+maintainers:
+  - Vinod Koul <vkoul@kernel.org>
+
+description: |
+  The LT9611 and LT9611UXC are bridge devices which convert DSI to HDMI
+
+properties:
+  compatible:
+    enum:
+      - lontium,lt9611
+      - lontium,lt9611uxc
+
+  reg:
+    maxItems: 1
+
+  "#sound-dai-cells":
+    const: 1
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active high RESET pin.
+
+  vdd-supply:
+    description: Regulator for 1.8V MIPI phy power.
+
+  vcc-supply:
+    description: Regulator for 3.3V IO power.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Primary MIPI port-1 for MIPI input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Additional MIPI port-2 for MIPI input, used in combination
+          with primary MIPI port-1 to drive higher resolution displays
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          HDMI port for HDMI output
+
+    required:
+      - port@0
+      - port@2
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - vdd-supply
+  - vcc-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c10 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      hdmi-bridge@3b {
+        compatible = "lontium,lt9611";
+        reg = <0x3b>;
+
+        reset-gpios = <&tlmm 128 GPIO_ACTIVE_HIGH>;
+        interrupts-extended = <&tlmm 84 IRQ_TYPE_EDGE_FALLING>;
+
+        vdd-supply = <&lt9611_1v8>;
+        vcc-supply = <&lt9611_3v3>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+            lt9611_a: endpoint {
+              remote-endpoint = <&dsi0_out>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+            lt9611_b: endpoint {
+              remote-endpoint = <&dsi1_out>;
+            };
+          };
+
+          port@2 {
+            reg = <2>;
+            lt9611_out: endpoint {
+              remote-endpoint = <&hdmi_con>;
+            };
+          };
+        };
+      };
+    };
+
+...
diff --git a/Bindings/display/bridge/lvds-codec.yaml b/Bindings/display/bridge/lvds-codec.yaml
new file mode 100644
index 0000000..84aafcb
--- /dev/null
+++ b/Bindings/display/bridge/lvds-codec.yaml
@@ -0,0 +1,186 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/lvds-codec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Transparent LVDS encoders and decoders
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  This binding supports transparent LVDS encoders and decoders that don't
+  require any configuration.
+
+  LVDS is a physical layer specification defined in ANSI/TIA/EIA-644-A. Multiple
+  incompatible data link layers have been used over time to transmit image data
+  to LVDS panels. This binding targets devices compatible with the following
+  specifications only.
+
+  [JEIDA] "Digital Interface Standards for Monitor", JEIDA-59-1999, February
+  1999 (Version 1.0), Japan Electronic Industry Development Association (JEIDA)
+  [LDI] "Open LVDS Display Interface", May 1999 (Version 0.95), National
+  Semiconductor
+  [VESA] "VESA Notebook Panel Standard", October 2007 (Version 1.0), Video
+  Electronics Standards Association (VESA)
+
+  Those devices have been marketed under the FPD-Link and FlatLink brand names
+  among others.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - ti,ds90c185   # For the TI DS90C185 FPD-Link Serializer
+              - ti,ds90c187   # For the TI DS90C187 FPD-Link Serializer
+              - ti,sn75lvds83 # For the TI SN75LVDS83 FlatLink transmitter
+          - const: lvds-encoder # Generic LVDS encoder compatible fallback
+      - items:
+          - enum:
+              - ti,ds90cf364a # For the DS90CF364A FPD-Link LVDS Receiver
+              - ti,ds90cf384a # For the DS90CF384A FPD-Link LVDS Receiver
+          - const: lvds-decoder # Generic LVDS decoders compatible fallback
+      - enum:
+          - thine,thc63lvdm83d # For the THC63LVDM83D LVDS serializer
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: |
+          For LVDS encoders, port 0 is the parallel input
+          For LVDS decoders, port 0 is the LVDS input
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-mapping:
+                enum:
+                  - jeida-18
+                  - jeida-24
+                  - vesa-24
+                description: |
+                  The color signals mapping order. See details in
+                  Documentation/devicetree/bindings/display/lvds.yaml
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+          For LVDS encoders, port 1 is the LVDS output
+          For LVDS decoders, port 1 is the parallel output
+
+    required:
+      - port@0
+      - port@1
+
+  pclk-sample:
+    description:
+      Data sampling on rising or falling edge.
+    enum:
+      - 0  # Falling edge
+      - 1  # Rising edge
+    default: 0
+
+  powerdown-gpios:
+    description:
+      The GPIO used to control the power down line of this device.
+    maxItems: 1
+
+  power-supply: true
+
+allOf:
+  - if:
+      not:
+        properties:
+          compatible:
+            contains:
+              const: lvds-decoder
+    then:
+      properties:
+        ports:
+          properties:
+            port@0:
+              properties:
+                endpoint:
+                  properties:
+                    data-mapping: false
+
+  - if:
+      not:
+        properties:
+          compatible:
+            contains:
+              const: lvds-encoder
+    then:
+      properties:
+        pclk-sample: false
+
+required:
+  - compatible
+  - ports
+
+additionalProperties: false
+
+
+examples:
+  - |
+    lvds-encoder {
+      compatible = "ti,ds90c185", "lvds-encoder";
+
+      ports {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        port@0 {
+          reg = <0>;
+
+          lvds_enc_in: endpoint {
+            remote-endpoint = <&display_out_rgb>;
+          };
+        };
+
+        port@1 {
+          reg = <1>;
+
+          lvds_enc_out: endpoint {
+            remote-endpoint = <&lvds_panel_in>;
+          };
+        };
+      };
+    };
+
+  - |
+    lvds-decoder {
+      compatible = "ti,ds90cf384a", "lvds-decoder";
+
+      ports {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        port@0 {
+          reg = <0>;
+
+          lvds_dec_in: endpoint {
+            remote-endpoint = <&display_out_lvds>;
+          };
+        };
+
+        port@1 {
+          reg = <1>;
+
+          lvds_dec_out: endpoint {
+            remote-endpoint = <&rgb_panel_in>;
+          };
+        };
+      };
+    };
+
+...
diff --git a/Bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt b/Bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt
new file mode 100644
index 0000000..09e0a21
--- /dev/null
+++ b/Bindings/display/bridge/megachips-stdpxxxx-ge-b850v3-fw.txt
@@ -0,0 +1,91 @@
+Drivers for the second video output of the GE B850v3:
+   STDP4028-ge-b850v3-fw bridges (LVDS-DP)
+   STDP2690-ge-b850v3-fw bridges (DP-DP++)
+
+The video processing pipeline on the second output on the GE B850v3:
+
+   Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
+
+Each bridge has a dedicated flash containing firmware for supporting the custom
+design. The result is that, in this design, neither the STDP4028 nor the
+STDP2690 behave as the stock bridges would. The compatible strings include the
+suffix "-ge-b850v3-fw" to make it clear that the driver is for the bridges with
+the firmware specific for the GE B850v3.
+
+The hardware do not provide control over the video processing pipeline, as the
+two bridges behaves as a single one. The only interfaces exposed by the
+hardware are EDID, HPD, and interrupts.
+
+stdp4028-ge-b850v3-fw required properties:
+  - compatible : "megachips,stdp4028-ge-b850v3-fw"
+  - reg : I2C bus address
+  - interrupts : one interrupt should be described here, as in
+    <0 IRQ_TYPE_LEVEL_HIGH>
+  - ports : One input port(reg = <0>) and one output port(reg = <1>)
+
+stdp2690-ge-b850v3-fw required properties:
+    compatible : "megachips,stdp2690-ge-b850v3-fw"
+  - reg : I2C bus address
+  - ports : One input port(reg = <0>) and one output port(reg = <1>)
+
+Example:
+
+&mux2_i2c2 {
+	clock-frequency = <100000>;
+
+	stdp4028@73 {
+		compatible = "megachips,stdp4028-ge-b850v3-fw";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg = <0x73>;
+
+		interrupt-parent = <&gpio2>;
+		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				stdp4028_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				stdp4028_out: endpoint {
+					remote-endpoint = <&stdp2690_in>;
+				};
+			};
+		};
+	};
+
+	stdp2690@72 {
+		compatible = "megachips,stdp2690-ge-b850v3-fw";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reg = <0x72>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				stdp2690_in: endpoint {
+					remote-endpoint = <&stdp4028_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				stdp2690_out: endpoint {
+					/* Connector for external display */
+				};
+			};
+		};
+	};
+};
diff --git a/Bindings/display/bridge/nwl-dsi.yaml b/Bindings/display/bridge/nwl-dsi.yaml
new file mode 100644
index 0000000..350fb8f
--- /dev/null
+++ b/Bindings/display/bridge/nwl-dsi.yaml
@@ -0,0 +1,202 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/nwl-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Northwest Logic MIPI-DSI controller on i.MX SoCs
+
+maintainers:
+  - Guido Gúnther <agx@sigxcpu.org>
+  - Robert Chiras <robert.chiras@nxp.com>
+
+description: |
+  NWL MIPI-DSI host controller found on i.MX8 platforms. This is a dsi bridge for
+  the SOCs NWL MIPI-DSI host controller.
+
+allOf:
+  - $ref: ../dsi-controller.yaml#
+
+properties:
+  compatible:
+    const: fsl,imx8mq-nwl-dsi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  assigned-clock-parents: true
+  assigned-clock-rates: true
+  assigned-clocks: true
+
+  clocks:
+    items:
+      - description: DSI core clock
+      - description: RX_ESC clock (used in escape mode)
+      - description: TX_ESC clock (used in escape mode)
+      - description: PHY_REF clock
+      - description: LCDIF clock
+
+  clock-names:
+    items:
+      - const: core
+      - const: rx_esc
+      - const: tx_esc
+      - const: phy_ref
+      - const: lcdif
+
+  mux-controls:
+    description:
+      mux controller node to use for operating the input mux
+
+  phys:
+    maxItems: 1
+    description:
+      A phandle to the phy module representing the DPHY
+
+  phy-names:
+    items:
+      - const: dphy
+
+  power-domains:
+    maxItems: 1
+
+  resets:
+    items:
+      - description: dsi byte reset line
+      - description: dsi dpi reset line
+      - description: dsi esc reset line
+      - description: dsi pclk reset line
+
+  reset-names:
+    items:
+      - const: byte
+      - const: dpi
+      - const: esc
+      - const: pclk
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        description:
+          Input port node to receive pixel data from the
+          display controller. Exactly one endpoint must be
+          specified.
+        properties:
+          endpoint@0:
+            $ref: /schemas/graph.yaml#/properties/endpoint
+            description: sub-node describing the input from LCDIF
+
+          endpoint@1:
+            $ref: /schemas/graph.yaml#/properties/endpoint
+            description: sub-node describing the input from DCSS
+
+        oneOf:
+          - required:
+              - endpoint@0
+          - required:
+              - endpoint@1
+
+        unevaluatedProperties: false
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          DSI output port node to the panel or the next bridge
+          in the chain
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - '#address-cells'
+  - '#size-cells'
+  - clock-names
+  - clocks
+  - compatible
+  - interrupts
+  - mux-controls
+  - phy-names
+  - phys
+  - ports
+  - reg
+  - reset-names
+  - resets
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx8mq-clock.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/reset/imx8mq-reset.h>
+
+    dsi@30a00000 {
+              #address-cells = <1>;
+              #size-cells = <0>;
+              compatible = "fsl,imx8mq-nwl-dsi";
+              reg = <0x30A00000 0x300>;
+              clocks = <&clk IMX8MQ_CLK_DSI_CORE>,
+                       <&clk IMX8MQ_CLK_DSI_AHB>,
+                       <&clk IMX8MQ_CLK_DSI_IPG_DIV>,
+                       <&clk IMX8MQ_CLK_DSI_PHY_REF>,
+                       <&clk IMX8MQ_CLK_LCDIF_PIXEL>;
+              clock-names = "core", "rx_esc", "tx_esc", "phy_ref", "lcdif";
+              interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+              mux-controls = <&mux 0>;
+              power-domains = <&pgc_mipi>;
+              resets = <&src IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N>,
+                       <&src IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N>,
+                       <&src IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N>,
+                       <&src IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N>;
+              reset-names = "byte", "dpi", "esc", "pclk";
+              phys = <&dphy>;
+              phy-names = "dphy";
+
+              panel@0 {
+                      compatible = "rocktech,jh057n00900";
+                      reg = <0>;
+                      vcc-supply = <&reg_2v8_p>;
+                      iovcc-supply = <&reg_1v8_p>;
+                      reset-gpios = <&gpio3 13 GPIO_ACTIVE_LOW>;
+                      port {
+                           panel_in: endpoint {
+                                     remote-endpoint = <&mipi_dsi_out>;
+                           };
+                      };
+              };
+
+              ports {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    port@0 {
+                           #size-cells = <0>;
+                           #address-cells = <1>;
+                           reg = <0>;
+                           mipi_dsi_in: endpoint@0 {
+                                        reg = <0>;
+                                        remote-endpoint = <&lcdif_mipi_dsi>;
+                           };
+                    };
+                    port@1 {
+                           reg = <1>;
+                           mipi_dsi_out: endpoint {
+                                         remote-endpoint = <&panel_in>;
+                           };
+                    };
+              };
+    };
diff --git a/Bindings/display/bridge/nxp,ptn3460.yaml b/Bindings/display/bridge/nxp,ptn3460.yaml
new file mode 100644
index 0000000..70ec709
--- /dev/null
+++ b/Bindings/display/bridge/nxp,ptn3460.yaml
@@ -0,0 +1,106 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/nxp,ptn3460.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP PTN3460 eDP to LVDS bridge
+
+maintainers:
+  - Sean Paul <seanpaul@chromium.org>
+
+properties:
+  compatible:
+    const: nxp,ptn3460
+
+  reg:
+    description: I2C address of the bridge
+    maxItems: 1
+
+  edid-emulation:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      The EDID emulation entry to use
+      Value  Resolution  Description
+        0     1024x768   NXP Generic
+        1     1920x1080  NXP Generic
+        2     1920x1080  NXP Generic
+        3     1600x900   Samsung LTM200KT
+        4     1920x1080  Samsung LTM230HT
+        5     1366x768   NXP Generic
+        6     1600x900   ChiMei M215HGE
+    enum: [0, 1, 2, 3, 4, 5, 6]
+
+  powerdown-gpios:
+    description: GPIO connected to the PD_N signal.
+    maxItems: 1
+
+  reset-gpios:
+    description: GPIO connected to the RST_N signal.
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for LVDS output
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for eDP input
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - edid-emulation
+  - powerdown-gpios
+  - reset-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@20 {
+        compatible = "nxp,ptn3460";
+        reg = <0x20>;
+        edid-emulation = <5>;
+        powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
+        reset-gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+            bridge_out: endpoint {
+              remote-endpoint = <&panel_in>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+            bridge_in: endpoint {
+              remote-endpoint = <&dp_out>;
+            };
+          };
+        };
+      };
+    };
+
+...
diff --git a/Bindings/display/bridge/nxp,tda998x.yaml b/Bindings/display/bridge/nxp,tda998x.yaml
new file mode 100644
index 0000000..21d995f2
--- /dev/null
+++ b/Bindings/display/bridge/nxp,tda998x.yaml
@@ -0,0 +1,110 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/nxp,tda998x.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: NXP TDA998x HDMI transmitter
+
+maintainers:
+  - Russell King <linux@armlinux.org.uk>
+
+properties:
+  compatible:
+    const: nxp,tda998x
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  video-ports:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0x230145
+    maximum: 0xffffff
+    description:
+      24 bits value which defines how the video controller output is wired to
+      the TDA998x input.
+
+  audio-ports:
+    description:
+      Array of 8-bit values, 2 values per DAI (Documentation/sound/soc/dai.rst).
+      The implementation allows one or two DAIs.
+      If two DAIs are defined, they must be of different type.
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    items:
+      minItems: 1
+      items:
+        - description: |
+            The first value defines the DAI type: TDA998x_SPDIF or TDA998x_I2S
+            (see include/dt-bindings/display/tda998x.h).
+        - description:
+            The second value defines the tda998x AP_ENA reg content when the
+            DAI in question is used.
+
+  '#sound-dai-cells':
+    enum: [ 0, 1 ]
+
+  nxp,calib-gpios:
+    maxItems: 1
+    description:
+      Calibration GPIO, which must correspond with the gpio used for the
+      TDA998x interrupt pin.
+
+  port:
+    $ref: /schemas/graph.yaml#/properties/port
+    description: Parallel input port
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        type: object
+        description: Parallel input port
+
+      port@1:
+        type: object
+        description: HDMI output port
+
+required:
+  - compatible
+  - reg
+
+oneOf:
+  - required:
+      - port
+  - required:
+      - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/display/tda998x.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        tda998x: hdmi-encoder@70 {
+            compatible = "nxp,tda998x";
+            reg = <0x70>;
+            interrupt-parent = <&gpio0>;
+            interrupts = <27 IRQ_TYPE_EDGE_FALLING>;
+            video-ports = <0x230145>;
+
+            #sound-dai-cells = <1>;
+                         /* DAI-format / AP_ENA reg value */
+            audio-ports = <TDA998x_SPDIF 0x04>,
+                          <TDA998x_I2S 0x03>;
+
+            port {
+                tda998x_in: endpoint {
+                    remote-endpoint = <&lcdc_0>;
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/parade,ps8622.yaml b/Bindings/display/bridge/parade,ps8622.yaml
new file mode 100644
index 0000000..e6397ac
--- /dev/null
+++ b/Bindings/display/bridge/parade,ps8622.yaml
@@ -0,0 +1,115 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/parade,ps8622.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Parade PS8622/PS8625 DisplayPort to LVDS Converter
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+properties:
+  compatible:
+    enum:
+      - parade,ps8622
+      - parade,ps8625
+
+  reg:
+    maxItems: 1
+
+  lane-count:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2]
+    description: Number of DP lanes to use.
+
+  use-external-pwm:
+    type: boolean
+    description: Backlight will be controlled by an external PWM.
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to RST_ pin.
+
+  sleep-gpios:
+    maxItems: 1
+    description: GPIO connected to PD_ pin.
+
+  vdd12-supply: true
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS output.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for DisplayPort input.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - reset-gpios
+  - sleep-gpios
+  - ports
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          const: parade,ps8622
+    then:
+      properties:
+        lane-count:
+          const: 1
+    else:
+      properties:
+        lane-count:
+          const: 2
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        lvds-bridge@48 {
+            compatible = "parade,ps8625";
+            reg = <0x48>;
+            sleep-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&gpy7 7 GPIO_ACTIVE_HIGH>;
+            lane-count = <2>;
+            use-external-pwm;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    bridge_out: endpoint {
+                        remote-endpoint = <&panel_in>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+
+                    bridge_in: endpoint {
+                        remote-endpoint = <&dp_out>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/ps8640.yaml b/Bindings/display/bridge/ps8640.yaml
new file mode 100644
index 0000000..5856450
--- /dev/null
+++ b/Bindings/display/bridge/ps8640.yaml
@@ -0,0 +1,121 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ps8640.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MIPI DSI to eDP Video Format Converter
+
+maintainers:
+  - Nicolas Boichat <drinkcat@chromium.org>
+
+description: |
+  The PS8640 is a low power MIPI-to-eDP video format converter supporting
+  mobile devices with embedded panel resolutions up to 2048 x 1536. The
+  device accepts a single channel of MIPI DSI v1.1, with up to four lanes
+  plus clock, at a transmission rate up to 1.5Gbit/sec per lane. The
+  device outputs eDP v1.4, one or two lanes, at a link rate of up to
+  3.24Gbit/sec per lane.
+
+properties:
+  compatible:
+    const: parade,ps8640
+
+  reg:
+    maxItems: 1
+    description: Base I2C address of the device.
+
+  powerdown-gpios:
+    maxItems: 1
+    description: GPIO connected to active low powerdown.
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active low reset.
+
+  vdd12-supply:
+    description: Regulator for 1.2V digital core power.
+
+  vdd33-supply:
+    description: Regulator for 3.3V digital core power.
+
+  aux-bus:
+    $ref: /schemas/display/dp-aux-bus.yaml#
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for DSI input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for eDP output (panel or connector).
+
+    required:
+      - port@0
+
+required:
+  - compatible
+  - reg
+  - powerdown-gpios
+  - reset-gpios
+  - vdd12-supply
+  - vdd33-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        ps8640: edp-bridge@18 {
+            compatible = "parade,ps8640";
+            reg = <0x18>;
+            powerdown-gpios = <&pio 116 GPIO_ACTIVE_LOW>;
+            reset-gpios = <&pio 115 GPIO_ACTIVE_LOW>;
+            vdd12-supply = <&ps8640_fixed_1v2>;
+            vdd33-supply = <&mt6397_vgp2_reg>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    ps8640_in: endpoint {
+                        remote-endpoint = <&dsi0_out>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    ps8640_out: endpoint {
+                        remote-endpoint = <&panel_in>;
+                    };
+                };
+            };
+
+            aux-bus {
+                panel {
+                    compatible = "boe,nv133fhm-n62";
+                    power-supply = <&pp3300_dx_edp>;
+                    backlight = <&backlight>;
+
+                    port {
+                        panel_in: endpoint {
+                            remote-endpoint = <&ps8640_out>;
+                        };
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/renesas,dsi-csi2-tx.yaml b/Bindings/display/bridge/renesas,dsi-csi2-tx.yaml
new file mode 100644
index 0000000..d33026f
--- /dev/null
+++ b/Bindings/display/bridge/renesas,dsi-csi2-tx.yaml
@@ -0,0 +1,119 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/renesas,dsi-csi2-tx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas R-Car MIPI DSI/CSI-2 Encoder
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  This binding describes the MIPI DSI/CSI-2 encoder embedded in the Renesas
+  R-Car Gen4 SoCs. The encoder can operate in either DSI or CSI-2 mode, with up
+  to four data lanes.
+
+properties:
+  compatible:
+    enum:
+      - renesas,r8a779a0-dsi-csi2-tx    # for V3U
+      - renesas,r8a779g0-dsi-csi2-tx    # for V4H
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Functional clock
+      - description: DSI (and CSI-2) functional clock
+      - description: PLL reference clock
+
+  clock-names:
+    items:
+      - const: fck
+      - const: dsi
+      - const: pll
+
+  power-domains:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Parallel input port
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: DSI/CSI-2 output port
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+
+            required:
+              - data-lanes
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - power-domains
+  - resets
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/r8a779a0-cpg-mssr.h>
+    #include <dt-bindings/power/r8a779a0-sysc.h>
+
+    dsi0: dsi-encoder@fed80000 {
+        compatible = "renesas,r8a779a0-dsi-csi2-tx";
+        reg = <0xfed80000 0x10000>;
+        power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+        clocks = <&cpg CPG_MOD 415>,
+                 <&cpg CPG_CORE R8A779A0_CLK_DSI>,
+                 <&cpg CPG_CORE R8A779A0_CLK_CP>;
+        clock-names = "fck", "dsi", "pll";
+        resets = <&cpg 415>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                dsi0_in: endpoint {
+                    remote-endpoint = <&du_out_dsi0>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                dsi0_out: endpoint {
+                    data-lanes = <1 2>;
+                    remote-endpoint = <&sn65dsi86_in>;
+                };
+            };
+        };
+    };
+...
diff --git a/Bindings/display/bridge/renesas,dsi.yaml b/Bindings/display/bridge/renesas,dsi.yaml
new file mode 100644
index 0000000..e08c246
--- /dev/null
+++ b/Bindings/display/bridge/renesas,dsi.yaml
@@ -0,0 +1,183 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/renesas,dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas RZ/G2L MIPI DSI Encoder
+
+maintainers:
+  - Biju Das <biju.das.jz@bp.renesas.com>
+
+description: |
+  This binding describes the MIPI DSI encoder embedded in the Renesas
+  RZ/G2L alike family of SoC's. The encoder can operate in DSI mode, with
+  up to four data lanes.
+
+allOf:
+  - $ref: /schemas/display/dsi-controller.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - renesas,r9a07g044-mipi-dsi # RZ/G2{L,LC}
+          - renesas,r9a07g054-mipi-dsi # RZ/V2L
+      - const: renesas,rzg2l-mipi-dsi
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    items:
+      - description: Sequence operation channel 0 interrupt
+      - description: Sequence operation channel 1 interrupt
+      - description: Video-Input operation channel 1 interrupt
+      - description: DSI Packet Receive interrupt
+      - description: DSI Fatal Error interrupt
+      - description: DSI D-PHY PPI interrupt
+      - description: Debug interrupt
+
+  interrupt-names:
+    items:
+      - const: seq0
+      - const: seq1
+      - const: vin1
+      - const: rcv
+      - const: ferr
+      - const: ppi
+      - const: debug
+
+  clocks:
+    items:
+      - description: DSI D-PHY PLL multiplied clock
+      - description: DSI D-PHY system clock
+      - description: DSI AXI bus clock
+      - description: DSI Register access clock
+      - description: DSI Video clock
+      - description: DSI D-PHY Escape mode transmit clock
+
+  clock-names:
+    items:
+      - const: pllclk
+      - const: sysclk
+      - const: aclk
+      - const: pclk
+      - const: vclk
+      - const: lpclk
+
+  resets:
+    items:
+      - description: MIPI_DSI_CMN_RSTB
+      - description: MIPI_DSI_ARESET_N
+      - description: MIPI_DSI_PRESET_N
+
+  reset-names:
+    items:
+      - const: rst
+      - const: arst
+      - const: prst
+
+  power-domains:
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Parallel input port
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: DSI output port
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                description: array of physical DSI data lane indexes.
+                minItems: 1
+                items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+            required:
+              - data-lanes
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - interrupt-names
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - power-domains
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/r9a07g044-cpg.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    dsi0: dsi@10850000 {
+        compatible = "renesas,r9a07g044-mipi-dsi", "renesas,rzg2l-mipi-dsi";
+        reg = <0x10850000 0x20000>;
+        interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "seq0", "seq1", "vin1", "rcv",
+                          "ferr", "ppi", "debug";
+        clocks = <&cpg CPG_MOD R9A07G044_MIPI_DSI_PLLCLK>,
+                 <&cpg CPG_MOD R9A07G044_MIPI_DSI_SYSCLK>,
+                 <&cpg CPG_MOD R9A07G044_MIPI_DSI_ACLK>,
+                 <&cpg CPG_MOD R9A07G044_MIPI_DSI_PCLK>,
+                 <&cpg CPG_MOD R9A07G044_MIPI_DSI_VCLK>,
+                 <&cpg CPG_MOD R9A07G044_MIPI_DSI_LPCLK>;
+        clock-names = "pllclk", "sysclk", "aclk", "pclk", "vclk", "lpclk";
+        resets = <&cpg R9A07G044_MIPI_DSI_CMN_RSTB>,
+                 <&cpg R9A07G044_MIPI_DSI_ARESET_N>,
+                 <&cpg R9A07G044_MIPI_DSI_PRESET_N>;
+        reset-names = "rst", "arst", "prst";
+        power-domains = <&cpg>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                dsi0_in: endpoint {
+                    remote-endpoint = <&du_out_dsi0>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                dsi0_out: endpoint {
+                    data-lanes = <1 2 3 4>;
+                    remote-endpoint = <&adv7535_in>;
+                };
+            };
+        };
+    };
+...
diff --git a/Bindings/display/bridge/renesas,dw-hdmi.yaml b/Bindings/display/bridge/renesas,dw-hdmi.yaml
new file mode 100644
index 0000000..e3ec697
--- /dev/null
+++ b/Bindings/display/bridge/renesas,dw-hdmi.yaml
@@ -0,0 +1,130 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/renesas,dw-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas R-Car DWC HDMI TX Encoder
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP
+  with a companion PHY IP.
+
+allOf:
+  - $ref: synopsys,dw-hdmi.yaml#
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - renesas,r8a774a1-hdmi # for RZ/G2M compatible HDMI TX
+          - renesas,r8a774b1-hdmi # for RZ/G2N compatible HDMI TX
+          - renesas,r8a774e1-hdmi # for RZ/G2H compatible HDMI TX
+          - renesas,r8a7795-hdmi # for R-Car H3 compatible HDMI TX
+          - renesas,r8a7796-hdmi # for R-Car M3-W compatible HDMI TX
+          - renesas,r8a77961-hdmi # for R-Car M3-W+ compatible HDMI TX
+          - renesas,r8a77965-hdmi # for R-Car M3-N compatible HDMI TX
+      - const: renesas,rcar-gen3-hdmi
+
+  reg-io-width:
+    const: 1
+
+  clocks:
+    maxItems: 2
+
+  clock-names:
+    maxItems: 2
+
+  resets:
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Parallel RGB input port
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: HDMI output port
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Sound input port
+
+    required:
+      - port@0
+      - port@1
+      - port@2
+
+  power-domains:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - interrupts
+  - ports
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/r8a7795-cpg-mssr.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/power/r8a7795-sysc.h>
+
+    hdmi@fead0000 {
+        compatible = "renesas,r8a7795-hdmi", "renesas,rcar-gen3-hdmi";
+        reg = <0xfead0000 0x10000>;
+        interrupts = <0 389 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&cpg CPG_CORE R8A7795_CLK_S0D4>, <&cpg CPG_MOD 729>;
+        clock-names = "iahb", "isfr";
+        power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+        resets = <&cpg 729>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            port@0 {
+                reg = <0>;
+                dw_hdmi0_in: endpoint {
+                    remote-endpoint = <&du_out_hdmi0>;
+                };
+            };
+            port@1 {
+                reg = <1>;
+                rcar_dw_hdmi0_out: endpoint {
+                    remote-endpoint = <&hdmi0_con>;
+                };
+            };
+            port@2 {
+                reg = <2>;
+                rcar_dw_hdmi0_sound_in: endpoint {
+                    remote-endpoint = <&hdmi_sound_out>;
+                };
+            };
+        };
+    };
+
+    hdmi0-out {
+        compatible = "hdmi-connector";
+        label = "HDMI0 OUT";
+        type = "a";
+
+        port {
+            hdmi0_con: endpoint {
+                remote-endpoint = <&rcar_dw_hdmi0_out>;
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/renesas,lvds.yaml b/Bindings/display/bridge/renesas,lvds.yaml
new file mode 100644
index 0000000..bb9dbfb
--- /dev/null
+++ b/Bindings/display/bridge/renesas,lvds.yaml
@@ -0,0 +1,235 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/renesas,lvds.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas R-Car LVDS Encoder
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  These DT bindings describe the LVDS encoder embedded in the Renesas R-Car
+  Gen2, R-Car Gen3, RZ/G1 and RZ/G2 SoCs.
+
+properties:
+  compatible:
+    enum:
+      - renesas,r8a7742-lvds # for RZ/G1H compatible LVDS encoders
+      - renesas,r8a7743-lvds # for RZ/G1M compatible LVDS encoders
+      - renesas,r8a7744-lvds # for RZ/G1N compatible LVDS encoders
+      - renesas,r8a774a1-lvds # for RZ/G2M compatible LVDS encoders
+      - renesas,r8a774b1-lvds # for RZ/G2N compatible LVDS encoders
+      - renesas,r8a774c0-lvds # for RZ/G2E compatible LVDS encoders
+      - renesas,r8a774e1-lvds # for RZ/G2H compatible LVDS encoders
+      - renesas,r8a7790-lvds # for R-Car H2 compatible LVDS encoders
+      - renesas,r8a7791-lvds # for R-Car M2-W compatible LVDS encoders
+      - renesas,r8a7793-lvds # for R-Car M2-N compatible LVDS encoders
+      - renesas,r8a7795-lvds # for R-Car H3 compatible LVDS encoders
+      - renesas,r8a7796-lvds # for R-Car M3-W compatible LVDS encoders
+      - renesas,r8a77961-lvds # for R-Car M3-W+ compatible LVDS encoders
+      - renesas,r8a77965-lvds # for R-Car M3-N compatible LVDS encoders
+      - renesas,r8a77970-lvds # for R-Car V3M compatible LVDS encoders
+      - renesas,r8a77980-lvds # for R-Car V3H compatible LVDS encoders
+      - renesas,r8a77990-lvds # for R-Car E3 compatible LVDS encoders
+      - renesas,r8a77995-lvds # for R-Car D3 compatible LVDS encoders
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    minItems: 1
+    maxItems: 4
+
+  clock-names:
+    minItems: 1
+    maxItems: 4
+
+  resets:
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Parallel RGB input port
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: LVDS output port
+
+    required:
+      - port@0
+      - port@1
+
+  power-domains:
+    maxItems: 1
+
+  renesas,companion:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description:
+      phandle to the companion LVDS encoder. This property is mandatory
+      for the first LVDS encoder on R-Car D3 and E3, and RZ/G2E SoCs, and shall
+      point to the second encoder to be used as a companion in dual-link mode.
+      It shall not be set for any other LVDS encoder.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - power-domains
+  - resets
+  - ports
+
+if:
+  properties:
+    compatible:
+      enum:
+        - renesas,r8a774c0-lvds
+        - renesas,r8a77990-lvds
+        - renesas,r8a77995-lvds
+then:
+  properties:
+    clocks:
+      minItems: 1
+      items:
+        - description: Functional clock
+        - description: EXTAL input clock
+        - description: DU_DOTCLKIN0 input clock
+        - description: DU_DOTCLKIN1 input clock
+
+    clock-names:
+      minItems: 1
+      items:
+        - const: fck
+        # The LVDS encoder can use the EXTAL or DU_DOTCLKINx clocks.
+        # These clocks are optional.
+        - enum:
+            - extal
+            - dclkin.0
+            - dclkin.1
+        - enum:
+            - extal
+            - dclkin.0
+            - dclkin.1
+        - enum:
+            - extal
+            - dclkin.0
+            - dclkin.1
+
+  required:
+    - clock-names
+
+else:
+  properties:
+    clocks:
+      items:
+        - description: Functional clock
+
+    clock-names:
+      items:
+        - const: fck
+
+    renesas,companion: false
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/renesas-cpg-mssr.h>
+    #include <dt-bindings/power/r8a7795-sysc.h>
+
+    lvds@feb90000 {
+        compatible = "renesas,r8a7795-lvds";
+        reg = <0xfeb90000 0x14>;
+        clocks = <&cpg CPG_MOD 727>;
+        power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+        resets = <&cpg 727>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                lvds_in: endpoint {
+                    remote-endpoint = <&du_out_lvds0>;
+                };
+            };
+            port@1 {
+                reg = <1>;
+                lvds_out: endpoint {
+                    remote-endpoint = <&panel_in>;
+                };
+            };
+        };
+    };
+
+  - |
+    #include <dt-bindings/clock/renesas-cpg-mssr.h>
+    #include <dt-bindings/power/r8a77990-sysc.h>
+
+    lvds0: lvds@feb90000 {
+        compatible = "renesas,r8a77990-lvds";
+        reg = <0xfeb90000 0x20>;
+        clocks = <&cpg CPG_MOD 727>,
+                 <&x13_clk>,
+                 <&extal_clk>;
+        clock-names = "fck", "dclkin.0", "extal";
+        power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
+        resets = <&cpg 727>;
+
+        renesas,companion = <&lvds1>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                lvds0_in: endpoint {
+                    remote-endpoint = <&du_out_lvds0>;
+                };
+            };
+            port@1 {
+                reg = <1>;
+                lvds0_out: endpoint {
+                    remote-endpoint = <&panel_in1>;
+                };
+            };
+        };
+    };
+
+    lvds1: lvds@feb90100 {
+        compatible = "renesas,r8a77990-lvds";
+        reg = <0xfeb90100 0x20>;
+        clocks = <&cpg CPG_MOD 727>,
+                 <&x13_clk>,
+                 <&extal_clk>;
+        clock-names = "fck", "dclkin.0", "extal";
+        power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
+        resets = <&cpg 726>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                lvds1_in: endpoint {
+                    remote-endpoint = <&du_out_lvds1>;
+                };
+            };
+            port@1 {
+                reg = <1>;
+                lvds1_out: endpoint {
+                    remote-endpoint = <&panel_in2>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/samsung,mipi-dsim.yaml b/Bindings/display/bridge/samsung,mipi-dsim.yaml
new file mode 100644
index 0000000..4ed7a79
--- /dev/null
+++ b/Bindings/display/bridge/samsung,mipi-dsim.yaml
@@ -0,0 +1,280 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/samsung,mipi-dsim.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung MIPI DSIM bridge controller
+
+maintainers:
+  - Inki Dae <inki.dae@samsung.com>
+  - Jagan Teki <jagan@amarulasolutions.com>
+  - Marek Szyprowski <m.szyprowski@samsung.com>
+
+description: |
+  Samsung MIPI DSIM bridge controller can be found it on Exynos
+  and i.MX8M Mini/Nano/Plus SoC's.
+
+properties:
+  compatible:
+    oneOf:
+      - enum:
+          - samsung,exynos3250-mipi-dsi
+          - samsung,exynos4210-mipi-dsi
+          - samsung,exynos5410-mipi-dsi
+          - samsung,exynos5422-mipi-dsi
+          - samsung,exynos5433-mipi-dsi
+          - fsl,imx8mm-mipi-dsim
+          - fsl,imx8mp-mipi-dsim
+      - items:
+          - const: fsl,imx8mn-mipi-dsim
+          - const: fsl,imx8mm-mipi-dsim
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  '#address-cells':
+    const: 1
+
+  '#size-cells':
+    const: 0
+
+  clocks:
+    minItems: 2
+    maxItems: 5
+
+  clock-names:
+    minItems: 2
+    maxItems: 5
+
+  samsung,phy-type:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: phandle to the samsung phy-type
+
+  power-domains:
+    maxItems: 1
+
+  samsung,power-domain:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: phandle to the associated samsung power domain
+
+  vddcore-supply:
+    description: MIPI DSIM Core voltage supply (e.g. 1.1V)
+
+  vddio-supply:
+    description: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V)
+
+  samsung,burst-clock-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      DSIM high speed burst mode frequency.  If absent,
+      the pixel clock from the attached device or bridge
+      will be used instead.
+
+  samsung,esc-clock-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      DSIM escape mode frequency.
+
+  samsung,pll-clock-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      DSIM oscillator clock frequency. If absent, the clock frequency
+      of sclk_mipi will be used instead.
+
+  phys:
+    maxItems: 1
+
+  phy-names:
+    const: dsim
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Input port node to receive pixel data from the
+          display controller. Exactly one endpoint must be
+          specified.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          DSI output port node to the panel or the next bridge
+          in the chain.
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                minItems: 1
+                maxItems: 4
+                uniqueItems: true
+                items:
+                  enum: [ 1, 2, 3, 4 ]
+
+              lane-polarities:
+                minItems: 1
+                maxItems: 5
+                description:
+                  The Samsung MIPI DSI IP requires that all the data lanes have
+                  the same polarity.
+
+            dependencies:
+              lane-polarities: [data-lanes]
+
+required:
+  - clock-names
+  - clocks
+  - compatible
+  - interrupts
+  - reg
+  - samsung,esc-clock-frequency
+
+allOf:
+  - $ref: ../dsi-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: samsung,exynos5433-mipi-dsi
+
+    then:
+      properties:
+        clocks:
+          minItems: 5
+
+        clock-names:
+          items:
+            - const: bus_clk
+            - const: phyclk_mipidphy0_bitclkdiv8
+            - const: phyclk_mipidphy0_rxclkesc0
+            - const: sclk_rgb_vclk_to_dsim0
+            - const: sclk_mipi
+
+        ports:
+          required:
+            - port@0
+
+      required:
+        - ports
+        - vddcore-supply
+        - vddio-supply
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: samsung,exynos5410-mipi-dsi
+
+    then:
+      properties:
+        clocks:
+          minItems: 2
+
+        clock-names:
+          items:
+            - const: bus_clk
+            - const: pll_clk
+
+      required:
+        - vddcore-supply
+        - vddio-supply
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: samsung,exynos4210-mipi-dsi
+
+    then:
+      properties:
+        clocks:
+          minItems: 2
+
+        clock-names:
+          items:
+            - const: bus_clk
+            - const: sclk_mipi
+
+      required:
+        - vddcore-supply
+        - vddio-supply
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: samsung,exynos3250-mipi-dsi
+
+    then:
+      properties:
+        clocks:
+          minItems: 2
+
+        clock-names:
+          items:
+            - const: bus_clk
+            - const: pll_clk
+
+      required:
+        - vddcore-supply
+        - vddio-supply
+        - samsung,phy-type
+
+additionalProperties:
+  type: object
+
+examples:
+  - |
+    #include <dt-bindings/clock/exynos5433.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    dsi@13900000 {
+       compatible = "samsung,exynos5433-mipi-dsi";
+       reg = <0x13900000 0xC0>;
+       interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+       phys = <&mipi_phy 1>;
+       phy-names = "dsim";
+       clocks = <&cmu_disp CLK_PCLK_DSIM0>,
+                <&cmu_disp CLK_PHYCLK_MIPIDPHY0_BITCLKDIV8>,
+                <&cmu_disp CLK_PHYCLK_MIPIDPHY0_RXCLKESC0>,
+                <&cmu_disp CLK_SCLK_RGB_VCLK_TO_DSIM0>,
+                <&cmu_disp CLK_SCLK_DSIM0>;
+       clock-names = "bus_clk",
+                     "phyclk_mipidphy0_bitclkdiv8",
+                     "phyclk_mipidphy0_rxclkesc0",
+                     "sclk_rgb_vclk_to_dsim0",
+                     "sclk_mipi";
+       power-domains = <&pd_disp>;
+       vddcore-supply = <&ldo6_reg>;
+       vddio-supply = <&ldo7_reg>;
+       samsung,burst-clock-frequency = <512000000>;
+       samsung,esc-clock-frequency = <16000000>;
+       samsung,pll-clock-frequency = <24000000>;
+       pinctrl-names = "default";
+       pinctrl-0 = <&te_irq>;
+
+       ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+             reg = <0>;
+
+             dsi_to_mic: endpoint {
+                remote-endpoint = <&mic_to_dsi>;
+             };
+          };
+       };
+    };
diff --git a/Bindings/display/bridge/sil,sii8620.yaml b/Bindings/display/bridge/sil,sii8620.yaml
new file mode 100644
index 0000000..6d1a36b
--- /dev/null
+++ b/Bindings/display/bridge/sil,sii8620.yaml
@@ -0,0 +1,108 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/sil,sii8620.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Image SiI8620 HDMI/MHL bridge
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
+
+properties:
+  compatible:
+    const: sil,sii8620
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: xtal
+
+  cvcc10-supply:
+    description: Digital Core Supply Voltage (1.0V)
+
+  interrupts:
+    maxItems: 1
+
+  iovcc18-supply:
+    description: I/O Supply Voltage (1.8V)
+
+  reset-gpios:
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    unevaluatedProperties: false
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for HDMI (encoder) input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          MHL to connector port
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - cvcc10-supply
+  - interrupts
+  - iovcc18-supply
+  - reset-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bridge@39 {
+            reg = <0x39>;
+            compatible = "sil,sii8620";
+            cvcc10-supply = <&ldo36_reg>;
+            iovcc18-supply = <&ldo34_reg>;
+            interrupt-parent = <&gpf0>;
+            interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
+            reset-gpios = <&gpv7 0 GPIO_ACTIVE_LOW>;
+            clocks = <&pmu_system_controller 0>;
+            clock-names = "xtal";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    mhl_to_hdmi: endpoint {
+                        remote-endpoint = <&hdmi_to_mhl>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    mhl_to_musb_con: endpoint {
+                        remote-endpoint = <&musb_con_to_mhl>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/sil,sii9022.yaml b/Bindings/display/bridge/sil,sii9022.yaml
new file mode 100644
index 0000000..5a69547
--- /dev/null
+++ b/Bindings/display/bridge/sil,sii9022.yaml
@@ -0,0 +1,131 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/sil,sii9022.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Image sii902x HDMI bridge
+
+maintainers:
+  - Boris Brezillon <bbrezillon@kernel.org>
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - sil,sii9022-cpi # CEC Programming Interface
+              - sil,sii9022-tpi # Transmitter Programming Interface
+          - const: sil,sii9022
+      - const: sil,sii9022
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+    description: Interrupt line used to inform the host about hotplug events.
+
+  reset-gpios:
+    maxItems: 1
+
+  iovcc-supply:
+    description: I/O Supply Voltage (1.8V or 3.3V)
+
+  cvcc12-supply:
+    description: Digital Core Supply Voltage (1.2V)
+
+  '#sound-dai-cells':
+    enum: [ 0, 1 ]
+    description: |
+      <0> if only I2S or S/PDIF pin is wired,
+      <1> if both are wired.
+      HDMI audio is configured only if this property is found.
+      If HDMI audio is configured, the sii902x device becomes an I2S and/or
+      S/PDIF audio codec component (e.g. a digital audio sink), that can be
+      used in configuring full audio devices with simple-card or
+      audio-graph-card bindings. See their binding documents on how to describe
+      the way the
+      sii902x device is connected to the rest of the audio system:
+      Documentation/devicetree/bindings/sound/simple-card.yaml
+      Documentation/devicetree/bindings/sound/audio-graph-card.yaml
+      Note: In case of the audio-graph-card binding the used port index should
+      be 3.
+
+  sil,i2s-data-lanes:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 1
+    maxItems: 4
+    uniqueItems: true
+    items:
+      enum: [ 0, 1, 2, 3 ]
+    description:
+      Each integer indicates which I2S pin is connected to which audio FIFO.
+      The first integer selects the I2S audio pin for the first audio FIFO#0
+      (HDMI channels 1&2), the second for FIFO#1 (HDMI channels 3&4), and so
+      on. There are 4 FIFOs and 4 I2S pins (SD0 - SD3). Any I2S pin can be
+      connected to any FIFO, but there can be no gaps. E.g. an I2S pin must be
+      mapped to FIFO#0 and FIFO#1 before mapping a channel to FIFO#2. The
+      default value is <0>, describing SD0 pin being routed to HDMI audio
+      FIFO#0.
+
+  clocks:
+    maxItems: 1
+    description: MCLK input. MCLK can be used to produce HDMI audio CTS values.
+
+  clock-names:
+    const: mclk
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Parallel RGB input port
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: HDMI output port
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Sound input port
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        hdmi-bridge@39 {
+            compatible = "sil,sii9022";
+            reg = <0x39>;
+            reset-gpios = <&pioA 1 0>;
+            iovcc-supply = <&v3v3_hdmi>;
+            cvcc12-supply = <&v1v2_hdmi>;
+
+            #sound-dai-cells = <0>;
+            sil,i2s-data-lanes = < 0 1 2 >;
+            clocks = <&mclk>;
+            clock-names = "mclk";
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    bridge_in: endpoint {
+                        remote-endpoint = <&dc_out>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/sil,sii9234.yaml b/Bindings/display/bridge/sil,sii9234.yaml
new file mode 100644
index 0000000..176181d
--- /dev/null
+++ b/Bindings/display/bridge/sil,sii9234.yaml
@@ -0,0 +1,110 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/sil,sii9234.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Image SiI9234 HDMI/MHL bridge
+
+maintainers:
+  - Maciej Purski <m.purski@samsung.com>
+
+properties:
+  compatible:
+    const: sil,sii9234
+
+  reg:
+    description: I2C address for TPI interface
+    maxItems: 1
+
+  avcc12-supply:
+    description: TMDS Analog Supply Voltage, 1.2V
+
+  avcc33-supply:
+    description: MHL/USB Switch Supply Voltage, 3.3V
+
+  cvcc12-supply:
+    description: Digital Core Supply Voltage, 1.2V
+
+  iovcc18-supply:
+    description: I/O voltage supply, 1.8V
+
+  interrupts:
+    maxItems: 1
+
+  reset-gpios:
+    description: GPIO connected to the reset pin.
+    maxItems: 1
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for HDMI (encoder) input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          MHL to connector port
+
+    required:
+      - port@0
+
+required:
+  - compatible
+  - reg
+  - avcc12-supply
+  - avcc33-supply
+  - cvcc12-supply
+  - iovcc18-supply
+  - interrupts
+  - reset-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@39 {
+        compatible = "sil,sii9234";
+        reg = <0x39>;
+        avcc12-supply = <&vsil12>;
+        avcc33-supply = <&vcc33mhl>;
+        cvcc12-supply = <&vsil12>;
+        iovcc18-supply = <&vcc18mhl>;
+        interrupt-parent = <&gpf3>;
+        interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+        reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+            mhl_to_hdmi: endpoint {
+              remote-endpoint = <&hdmi_to_mhl>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+            mhl_to_connector: endpoint {
+              remote-endpoint = <&connector_to_mhl>;
+            };
+          };
+        };
+      };
+    };
+
+...
diff --git a/Bindings/display/bridge/simple-bridge.yaml b/Bindings/display/bridge/simple-bridge.yaml
new file mode 100644
index 0000000..43cf4df
--- /dev/null
+++ b/Bindings/display/bridge/simple-bridge.yaml
@@ -0,0 +1,91 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/simple-bridge.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Transparent non-programmable DRM bridges
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+  - Maxime Ripard <mripard@kernel.org>
+
+description: |
+  This binding supports transparent non-programmable bridges that don't require
+  any configuration, with a single input and a single output.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - ti,ths8134a
+              - ti,ths8134b
+          - const: ti,ths8134
+      - items:
+          - const: corpro,gm7123
+          - const: adi,adv7123
+      - enum:
+          - adi,adv7123
+          - dumb-vga-dac
+          - ti,opa362
+          - ti,ths8134
+          - ti,ths8135
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: The bridge input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: The bridge output
+
+    required:
+      - port@0
+      - port@1
+
+  enable-gpios:
+    maxItems: 1
+    description: GPIO controlling bridge enable
+
+  vdd-supply:
+    description: Power supply for the bridge
+
+required:
+  - compatible
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    bridge {
+        compatible = "ti,ths8134a", "ti,ths8134";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+
+                vga_bridge_in: endpoint {
+                    remote-endpoint = <&tcon0_out_vga>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+
+                vga_bridge_out: endpoint {
+                    remote-endpoint = <&vga_con_in>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/snps,dw-mipi-dsi.yaml b/Bindings/display/bridge/snps,dw-mipi-dsi.yaml
new file mode 100644
index 0000000..8747b95
--- /dev/null
+++ b/Bindings/display/bridge/snps,dw-mipi-dsi.yaml
@@ -0,0 +1,61 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/snps,dw-mipi-dsi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys DesignWare MIPI DSI host controller
+
+maintainers:
+  - Philippe CORNU <philippe.cornu@foss.st.com>
+
+description: |
+  This document defines device tree properties for the Synopsys DesignWare MIPI
+  DSI host controller. It doesn't constitute a device tree binding specification
+  by itself but is meant to be referenced by platform-specific device tree
+  bindings.
+
+  When referenced from platform device tree bindings the properties defined in
+  this document are defined as follows. The platform device tree bindings are
+  responsible for defining whether each property is required or optional.
+
+allOf:
+  - $ref: ../dsi-controller.yaml#
+
+properties:
+  reg:
+    maxItems: 1
+
+  clocks: true
+
+  clock-names: true
+
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: apb
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Input node to receive pixel data.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: DSI output node to panel.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - clock-names
+  - clocks
+  - ports
+  - reg
+
+additionalProperties: true
diff --git a/Bindings/display/bridge/synopsys,dw-hdmi.yaml b/Bindings/display/bridge/synopsys,dw-hdmi.yaml
new file mode 100644
index 0000000..4b7e54a
--- /dev/null
+++ b/Bindings/display/bridge/synopsys,dw-hdmi.yaml
@@ -0,0 +1,53 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/synopsys,dw-hdmi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Common Properties for Synopsys DesignWare HDMI TX Controller
+
+maintainers:
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  This document defines device tree properties for the Synopsys DesignWare HDMI
+  TX controller (DWC HDMI TX) IP core. It doesn't constitute a full device tree
+  binding specification by itself but is meant to be referenced by device tree
+  bindings for the platform-specific integrations of the DWC HDMI TX.
+
+  When referenced from platform device tree bindings the properties defined in
+  this document are defined as follows. The platform device tree bindings are
+  responsible for defining whether each property is required or optional.
+
+properties:
+  reg:
+    maxItems: 1
+
+  reg-io-width:
+    description:
+      Width (in bytes) of the registers specified by the reg property.
+    enum: [1, 4]
+    default: 1
+
+  clocks:
+    minItems: 2
+    maxItems: 5
+    items:
+      - description: The bus clock for either AHB and APB
+      - description: The internal register configuration clock
+    additionalItems: true
+
+  clock-names:
+    minItems: 2
+    maxItems: 5
+    items:
+      - const: iahb
+      - const: isfr
+    additionalItems: true
+
+  interrupts:
+    maxItems: 1
+
+additionalProperties: true
+
+...
diff --git a/Bindings/display/bridge/thine,thc63lvd1024.yaml b/Bindings/display/bridge/thine,thc63lvd1024.yaml
new file mode 100644
index 0000000..8ae3824
--- /dev/null
+++ b/Bindings/display/bridge/thine,thc63lvd1024.yaml
@@ -0,0 +1,115 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/thine,thc63lvd1024.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Thine Electronics THC63LVD1024 LVDS Decoder
+
+maintainers:
+  - Jacopo Mondi <jacopo+renesas@jmondi.org>
+  - Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
+
+description: |
+  The THC63LVD1024 is a dual link LVDS receiver designed to convert LVDS
+  streams to parallel data outputs. The chip supports single/dual input/output
+  modes, handling up to two LVDS input streams and up to two digital CMOS/TTL
+  outputs.
+
+  Single or dual operation mode, output data mapping and DDR output modes are
+  configured through input signals and the chip does not expose any control
+  bus.
+
+properties:
+  compatible:
+    const: thine,thc63lvd1024
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+    description: |
+      The device can operate in single or dual input and output modes.
+
+      When operating in single input mode, all pixels are received on port@0,
+      and port@1 shall not contain any endpoint. In dual input mode,
+      even-numbered pixels are received on port@0 and odd-numbered pixels on
+      port@1, and both port@0 and port@1 shall contain endpoints.
+
+      When operating in single output mode all pixels are output from the first
+      CMOS/TTL port and port@3 shall not contain any endpoint. In dual output
+      mode pixels are output from both CMOS/TTL ports and both port@2 and
+      port@3 shall contain endpoints.
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: First LVDS input port
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Second LVDS input port
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: First digital CMOS/TTL parallel output
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Second digital CMOS/TTL parallel output
+
+    required:
+      - port@0
+      - port@2
+
+  oe-gpios:
+    maxItems: 1
+    description: Output enable GPIO signal, pin name "OE", active high.
+
+  powerdown-gpios:
+    maxItems: 1
+    description: Power down GPIO signal, pin name "/PDWN", active low.
+
+  vcc-supply:
+    description:
+      Power supply for the TTL output, TTL CLOCKOUT signal, LVDS input, PLL and
+      digital circuitry.
+
+required:
+  - compatible
+  - ports
+  - vcc-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    lvds-decoder {
+        compatible = "thine,thc63lvd1024";
+
+        vcc-supply = <&reg_lvds_vcc>;
+        powerdown-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+
+                lvds_dec_in_0: endpoint {
+                    remote-endpoint = <&lvds_out>;
+                };
+            };
+
+            port@2 {
+                reg = <2>;
+
+                lvds_dec_out_2: endpoint {
+                    remote-endpoint = <&adv7511_in>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/ti,dlpc3433.yaml b/Bindings/display/bridge/ti,dlpc3433.yaml
new file mode 100644
index 0000000..d3f84d2
--- /dev/null
+++ b/Bindings/display/bridge/ti,dlpc3433.yaml
@@ -0,0 +1,117 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ti,dlpc3433.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TI DLPC3433 MIPI DSI to DMD bridge
+
+maintainers:
+  - Jagan Teki <jagan@amarulasolutions.com>
+  - Christopher Vollo <chris@renewoutreach.org>
+
+description: |
+  TI DLPC3433 is a MIPI DSI based display controller bridge
+  for processing high resolution DMD based projectors.
+
+  It has a flexible configuration of MIPI DSI and DPI signal
+  input that produces a DMD output in RGB565, RGB666, RGB888
+  formats.
+
+  It supports upto 720p resolution with 60 and 120 Hz refresh
+  rates.
+
+properties:
+  compatible:
+    const: ti,dlpc3433
+
+  reg:
+    enum:
+      - 0x1b
+      - 0x1d
+
+  enable-gpios:
+    description: PROJ_ON pin, chip powers up PROJ_ON is high.
+
+  vcc_intf-supply:
+    description: A 1.8V/3.3V supply that power the Host I/O.
+
+  vcc_flsh-supply:
+    description: A 1.8V/3.3V supply that power the Flash I/O.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: Video port for MIPI DSI input.
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                description: array of physical DSI data lane indexes.
+                minItems: 1
+                items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for DMD output.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - enable-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bridge@1b {
+            compatible = "ti,dlpc3433";
+            reg = <0x1b>;
+            enable-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    bridge_in_dsi: endpoint {
+                        remote-endpoint = <&dsi_out_bridge>;
+                        data-lanes = <1 2 3 4>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+
+                    bridge_out_panel: endpoint {
+                        remote-endpoint = <&panel_out_bridge>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/ti,sn65dsi83.yaml b/Bindings/display/bridge/ti,sn65dsi83.yaml
new file mode 100644
index 0000000..48a97bb
--- /dev/null
+++ b/Bindings/display/bridge/ti,sn65dsi83.yaml
@@ -0,0 +1,162 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ti,sn65dsi83.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SN65DSI83 and SN65DSI84 DSI to LVDS bridge chip
+
+maintainers:
+  - Marek Vasut <marex@denx.de>
+
+description: |
+  Texas Instruments SN65DSI83 1x Single-link MIPI DSI
+  to 1x Single-link LVDS
+  https://www.ti.com/lit/gpn/sn65dsi83
+  Texas Instruments SN65DSI84 1x Single-link MIPI DSI
+  to 1x Dual-link or 2x Single-link LVDS
+  https://www.ti.com/lit/gpn/sn65dsi84
+
+properties:
+  compatible:
+    enum:
+      - ti,sn65dsi83
+      - ti,sn65dsi84
+
+  reg:
+    enum:
+      - 0x2c
+      - 0x2d
+
+  enable-gpios:
+    maxItems: 1
+    description: GPIO specifier for bridge_en pin (active high).
+
+  vcc-supply:
+    description: A 1.8V power supply (see regulator/regulator.yaml).
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: Video port for MIPI DSI Channel-A input
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                description: array of physical DSI data lane indexes.
+                minItems: 1
+                items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: Video port for MIPI DSI Channel-B input
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                description: array of physical DSI data lane indexes.
+                minItems: 1
+                items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS Channel-A output (panel or bridge).
+
+      port@3:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: Video port for LVDS Channel-B output (panel or bridge).
+
+    required:
+      - port@0
+      - port@2
+
+required:
+  - compatible
+  - reg
+  - ports
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ti,sn65dsi83
+    then:
+      properties:
+        ports:
+          properties:
+            port@1: false
+            port@3: false
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: ti,sn65dsi84
+    then:
+      properties:
+        ports:
+          properties:
+            port@1: false
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bridge@2d {
+            compatible = "ti,sn65dsi83";
+            reg = <0x2d>;
+
+            enable-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+            vcc-supply = <&reg_sn65dsi83_1v8>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+
+                    endpoint {
+                        remote-endpoint = <&dsi0_out>;
+                        data-lanes = <1 2 3 4>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+
+                    endpoint {
+                        remote-endpoint = <&panel_in_lvds>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/ti,sn65dsi86.yaml b/Bindings/display/bridge/ti,sn65dsi86.yaml
new file mode 100644
index 0000000..6ec6d28
--- /dev/null
+++ b/Bindings/display/bridge/ti,sn65dsi86.yaml
@@ -0,0 +1,273 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ti,sn65dsi86.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: SN65DSI86 DSI to eDP bridge chip
+
+maintainers:
+  - Sandeep Panda <spanda@codeaurora.org>
+
+description: |
+  The Texas Instruments SN65DSI86 bridge takes MIPI DSI in and outputs eDP.
+  https://www.ti.com/general/docs/lit/getliterature.tsp?genericPartNumber=sn65dsi86&fileType=pdf
+
+properties:
+  compatible:
+    const: ti,sn65dsi86
+
+  reg:
+    enum: [ 0x2c, 0x2d ]
+
+  enable-gpios:
+    maxItems: 1
+    description: GPIO specifier for bridge_en pin (active high).
+
+  suspend-gpios:
+    maxItems: 1
+    description: GPIO specifier for GPIO1 pin on bridge (active low).
+
+  no-hpd:
+    type: boolean
+    description:
+      Set if the HPD line on the bridge isn't hooked up to anything or is
+      otherwise unusable.
+
+  vccio-supply:
+    description: A 1.8V supply that powers the digital IOs.
+
+  vpll-supply:
+    description: A 1.8V supply that powers the DisplayPort PLL.
+
+  vcca-supply:
+    description: A 1.2V supply that powers the analog circuits.
+
+  vcc-supply:
+    description: A 1.2V supply that powers the digital core.
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+    description:
+      Clock specifier for input reference clock. The reference clock rate must
+      be 12 MHz, 19.2 MHz, 26 MHz, 27 MHz or 38.4 MHz.
+
+  clock-names:
+    const: refclk
+
+  gpio-controller: true
+  '#gpio-cells':
+    const: 2
+    description:
+      First cell is pin number, second cell is flags.  GPIO pin numbers are
+      1-based to match the datasheet.  See ../../gpio/gpio.txt for more
+      information.
+
+  '#pwm-cells':
+    const: 1
+    description: See ../../pwm/pwm.yaml for description of the cell formats.
+
+  aux-bus:
+    $ref: /schemas/display/dp-aux-bus.yaml#
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DSI input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description:
+          Video port for eDP output (panel or connector).
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                oneOf:
+                  - minItems: 1
+                    maxItems: 1
+                    uniqueItems: true
+                    items:
+                      enum:
+                        - 0
+                        - 1
+                    description:
+                      If you have 1 logical lane the bridge supports routing
+                      to either port 0 or port 1.  Port 0 is suggested.
+
+                  - minItems: 2
+                    maxItems: 2
+                    uniqueItems: true
+                    items:
+                      enum:
+                        - 0
+                        - 1
+                    description:
+                      If you have 2 logical lanes the bridge supports
+                      reordering but only on physical ports 0 and 1.
+
+                  - minItems: 4
+                    maxItems: 4
+                    uniqueItems: true
+                    items:
+                      enum:
+                        - 0
+                        - 1
+                        - 2
+                        - 3
+                    description:
+                      If you have 4 logical lanes the bridge supports
+                      reordering in any way.
+
+              lane-polarities:
+                minItems: 1
+                maxItems: 4
+                items:
+                  enum:
+                    - 0
+                    - 1
+
+            dependencies:
+              lane-polarities: [data-lanes]
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - vccio-supply
+  - vpll-supply
+  - vcca-supply
+  - vcc-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,rpmh.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@2d {
+        compatible = "ti,sn65dsi86";
+        reg = <0x2d>;
+
+        interrupt-parent = <&tlmm>;
+        interrupts = <10 IRQ_TYPE_LEVEL_HIGH>;
+
+        enable-gpios = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+
+        vpll-supply = <&src_pp1800_s4a>;
+        vccio-supply = <&src_pp1800_s4a>;
+        vcca-supply = <&src_pp1200_l2a>;
+        vcc-supply = <&src_pp1200_l2a>;
+
+        clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+        clock-names = "refclk";
+
+        no-hpd;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+            endpoint {
+              remote-endpoint = <&dsi0_out>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+            sn65dsi86_out: endpoint {
+              remote-endpoint = <&panel_in_edp>;
+            };
+          };
+        };
+
+        aux-bus {
+          panel {
+            compatible = "boe,nv133fhm-n62";
+            power-supply = <&pp3300_dx_edp>;
+            backlight = <&backlight>;
+            hpd-gpios = <&sn65dsi86_bridge 2 GPIO_ACTIVE_HIGH>;
+
+            port {
+              panel_in_edp: endpoint {
+                remote-endpoint = <&sn65dsi86_out>;
+              };
+            };
+          };
+        };
+      };
+    };
+  - |
+    #include <dt-bindings/clock/qcom,rpmh.h>
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@2d {
+        compatible = "ti,sn65dsi86";
+        reg = <0x2d>;
+
+        enable-gpios = <&msmgpio 33 GPIO_ACTIVE_HIGH>;
+        suspend-gpios = <&msmgpio 34 GPIO_ACTIVE_LOW>;
+
+        interrupts-extended = <&gpio3 4 IRQ_TYPE_EDGE_FALLING>;
+
+        vccio-supply = <&pm8916_l17>;
+        vcca-supply = <&pm8916_l6>;
+        vpll-supply = <&pm8916_l17>;
+        vcc-supply = <&pm8916_l6>;
+
+        clock-names = "refclk";
+        clocks = <&input_refclk>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+
+            edp_bridge_in: endpoint {
+              remote-endpoint = <&dsi_out>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+
+            edp_bridge_out: endpoint {
+              data-lanes = <2 1 3 0>;
+              lane-polarities = <0 1 0 1>;
+              remote-endpoint = <&edp_panel_in>;
+            };
+          };
+        };
+      };
+    };
diff --git a/Bindings/display/bridge/ti,tfp410.yaml b/Bindings/display/bridge/ti,tfp410.yaml
new file mode 100644
index 0000000..4c5dd8e
--- /dev/null
+++ b/Bindings/display/bridge/ti,tfp410.yaml
@@ -0,0 +1,119 @@
+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/ti,tfp410.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TFP410 DPI to DVI encoder
+
+maintainers:
+  - Tomi Valkeinen <tomi.valkeinen@ti.com>
+  - Jyri Sarha <jsarha@ti.com>
+
+properties:
+  compatible:
+    const: ti,tfp410
+
+  reg:
+    description: I2C address of the device.
+    maxItems: 1
+
+  powerdown-gpios:
+    maxItems: 1
+
+  ti,deskew:
+    description:
+      Data de-skew value in 350ps increments, from 0 to 7, as configured
+      through the DK[3:1] pins. The de-skew multiplier is computed as
+      (DK[3:1] - 4), so it ranges from -4 to 3.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 7
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: DPI input port.
+
+        properties:
+          endpoint:
+            $ref: /schemas/graph.yaml#/$defs/endpoint-base
+            unevaluatedProperties: false
+
+            properties:
+              pclk-sample:
+                description:
+                  Endpoint sampling edge.
+                enum:
+                  - 0  # Falling edge
+                  - 1  # Rising edge
+                default: 0
+
+              bus-width:
+                description:
+                  Endpoint bus width.
+                enum:
+                  - 12  # 12 data lines connected and dual-edge mode
+                  - 24  # 24 data lines connected and single-edge mode
+                default: 24
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: DVI output port.
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - ports
+
+if:
+  required:
+    - reg
+then:
+  properties:
+    ti,deskew: false
+else:
+  required:
+    - ti,deskew
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    tfp410: encoder {
+        compatible = "ti,tfp410";
+        powerdown-gpios = <&twl_gpio 2 GPIO_ACTIVE_LOW>;
+        ti,deskew = <3>;
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+
+            port@0 {
+                reg = <0>;
+                tfp410_in: endpoint {
+                    pclk-sample = <1>;
+                    bus-width = <24>;
+                    remote-endpoint = <&dpi_out>;
+                };
+            };
+
+            port@1 {
+                reg = <1>;
+                tfp410_out: endpoint {
+                    remote-endpoint = <&dvi_connector_in>;
+                };
+            };
+        };
+    };
+
+...
diff --git a/Bindings/display/bridge/toshiba,tc358762.yaml b/Bindings/display/bridge/toshiba,tc358762.yaml
new file mode 100644
index 0000000..6c1de0b
--- /dev/null
+++ b/Bindings/display/bridge/toshiba,tc358762.yaml
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/toshiba,tc358762.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba TC358762 MIPI DSI to MIPI DPI bridge
+
+maintainers:
+  - Marek Vasut <marex@denx.de>
+
+description: |
+  The TC358762 is bridge device which converts MIPI DSI to MIPI DPI.
+
+properties:
+  compatible:
+    enum:
+      - toshiba,tc358762
+
+  reg:
+    maxItems: 1
+    description: virtual channel number of a DSI peripheral
+
+  reset-gpios:
+    maxItems: 1
+
+  vddc-supply:
+    description: Regulator for 1.2V internal core power.
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DSI input
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DPI output (panel or connector).
+
+    required:
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - vddc-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      bridge@0 {
+        reg = <0>;
+        compatible = "toshiba,tc358762";
+        vddc-supply = <&vcc_1v2_reg>;
+
+        ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+            bridge_in: endpoint {
+              remote-endpoint = <&dsi_out>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+            bridge_out: endpoint {
+              remote-endpoint = <&panel_in>;
+            };
+          };
+        };
+      };
+    };
+
+...
diff --git a/Bindings/display/bridge/toshiba,tc358764.yaml b/Bindings/display/bridge/toshiba,tc358764.yaml
new file mode 100644
index 0000000..8666074
--- /dev/null
+++ b/Bindings/display/bridge/toshiba,tc358764.yaml
@@ -0,0 +1,89 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/toshiba,tc358764.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba TC358764 MIPI-DSI to LVDS bridge
+
+maintainers:
+  - Andrzej Hajda <andrzej.hajda@intel.com>
+
+properties:
+  compatible:
+    const: toshiba,tc358764
+
+  reg:
+    description: Virtual channel number of a DSI peripheral
+    maxItems: 1
+
+  reset-gpios:
+    maxItems: 1
+
+  vddc-supply:
+    description: Core voltage supply, 1.2V
+
+  vddio-supply:
+    description: I/O voltage supply, 1.8V or 3.3V
+
+  vddlvds-supply:
+    description: LVDS1/2 voltage supply, 3.3V
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for MIPI DSI input, if the bridge DSI controlled
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description:
+          Video port for LVDS output (panel or connector).
+
+    required:
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - reset-gpios
+  - vddc-supply
+  - vddio-supply
+  - vddlvds-supply
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        bridge@0 {
+            compatible = "toshiba,tc358764";
+            reg = <0>;
+
+            reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>;
+            vddc-supply = <&vcc_1v2_reg>;
+            vddio-supply = <&vcc_1v8_reg>;
+            vddlvds-supply = <&vcc_3v3_reg>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@1 {
+                    reg = <1>;
+                    lvds_ep: endpoint {
+                      remote-endpoint = <&panel_ep>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/toshiba,tc358767.yaml b/Bindings/display/bridge/toshiba,tc358767.yaml
new file mode 100644
index 0000000..ae894d9
--- /dev/null
+++ b/Bindings/display/bridge/toshiba,tc358767.yaml
@@ -0,0 +1,185 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/toshiba,tc358767.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba TC358767/TC358867/TC9595 DSI/DPI/eDP bridge
+
+maintainers:
+  - Andrey Gusakov <andrey.gusakov@cogentembedded.com>
+
+description: |
+  The TC358767/TC358867/TC9595 is bridge device which
+  converts DSI/DPI to eDP/DP .
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - toshiba,tc358867
+              - toshiba,tc9595
+          - const: toshiba,tc358767
+      - const: toshiba,tc358767
+
+  reg:
+    enum:
+      - 0x68
+      - 0x0f
+    description: |
+        i2c address of the bridge, 0x68 or 0x0f, depending on bootstrap pins
+
+  clock-names:
+    const: ref
+
+  clocks:
+    maxItems: 1
+    description: |
+        OF device-tree clock specification for refclk input. The reference.
+        clock rate must be 13 MHz, 19.2 MHz, 26 MHz, or 38.4 MHz.
+
+  shutdown-gpios:
+    maxItems: 1
+    description: |
+        OF device-tree gpio specification for SD pin(active high shutdown input)
+
+  reset-gpios:
+    maxItems: 1
+    description: |
+        OF device-tree gpio specification for RSTX pin(active low system reset)
+
+  interrupts:
+    maxItems: 1
+
+  toshiba,hpd-pin:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum:
+      - 0
+      - 1
+    description: TC358767 GPIO pin number to which HPD is connected to (0 or 1)
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: |
+            DSI input port. The remote endpoint phandle should be a
+            reference to a valid DSI output endpoint node
+
+        properties:
+          endpoint:
+            $ref: /schemas/media/video-interfaces.yaml#
+            unevaluatedProperties: false
+
+            properties:
+              data-lanes:
+                description: array of physical DSI data lane indexes.
+                minItems: 1
+                items:
+                  - const: 1
+                  - const: 2
+                  - const: 3
+                  - const: 4
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+            DPI input/output port. The remote endpoint phandle should be a
+            reference to a valid DPI output or input endpoint node.
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+            eDP/DP output port. The remote endpoint phandle should be a
+            reference to a valid eDP panel input endpoint node. This port is
+            optional, treated as DP panel if not defined
+
+    oneOf:
+      - required:
+          - port@0
+      - required:
+          - port@1
+
+
+required:
+  - compatible
+  - reg
+  - clock-names
+  - clocks
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    /* DPI input and eDP output */
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        edp-bridge@68 {
+            compatible = "toshiba,tc358767";
+            reg = <0x68>;
+            shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+            clock-names = "ref";
+            clocks = <&edp_refclk>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@1 {
+                    reg = <1>;
+
+                    bridge_in_0: endpoint {
+                        remote-endpoint = <&dpi_out>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+
+                    bridge_out: endpoint {
+                        remote-endpoint = <&panel_in>;
+                    };
+                };
+            };
+        };
+    };
+  - |
+    /* DPI input and DP output */
+
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        edp-bridge@68 {
+            compatible = "toshiba,tc358767";
+            reg = <0x68>;
+            shutdown-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+            reset-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+            clock-names = "ref";
+            clocks = <&edp_refclk>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@1 {
+                    reg = <1>;
+
+                    bridge_in_1: endpoint {
+                        remote-endpoint = <&dpi_out>;
+                    };
+                };
+            };
+        };
+    };
diff --git a/Bindings/display/bridge/toshiba,tc358768.yaml b/Bindings/display/bridge/toshiba,tc358768.yaml
new file mode 100644
index 0000000..779d8c5
--- /dev/null
+++ b/Bindings/display/bridge/toshiba,tc358768.yaml
@@ -0,0 +1,127 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/toshiba,tc358768.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toschiba TC358768/TC358778 Parallel RGB to MIPI DSI bridge
+
+maintainers:
+  - Peter Ujfalusi <peter.ujfalusi@ti.com>
+
+description: |
+  The TC358768/TC358778 is bridge device which converts RGB to DSI.
+
+properties:
+  compatible:
+    enum:
+      - toshiba,tc358768
+      - toshiba,tc358778
+
+  reg:
+    maxItems: 1
+    description: base I2C address of the device
+
+  reset-gpios:
+    maxItems: 1
+    description: GPIO connected to active low RESX pin
+
+  vddc-supply:
+    description: Regulator for 1.2V internal core power.
+
+  vddmipi-supply:
+    description: Regulator for 1.2V for the MIPI.
+
+  vddio-supply:
+    description: Regulator for 1.8V - 3.3V IO power.
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    const: refclk
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
+        description: |
+          Video port for RGB input
+
+        properties:
+          endpoint:
+            $ref: /schemas/graph.yaml#/$defs/endpoint-base
+            unevaluatedProperties: false
+
+            properties:
+              data-lines:
+                $ref: /schemas/types.yaml#/definitions/uint32
+                enum: [ 16, 18, 24 ]
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+          Video port for DSI output (panel or connector).
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - vddc-supply
+  - vddmipi-supply
+  - vddio-supply
+  - ports
+
+allOf:
+  - $ref: ../dsi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      dsi_bridge: dsi@e {
+        compatible = "toshiba,tc358768";
+        reg = <0xe>;
+
+        clocks = <&tc358768_refclk>;
+        clock-names = "refclk";
+
+        reset-gpios = <&pcf_display_board 0 GPIO_ACTIVE_LOW>;
+
+        vddc-supply = <&v1_2d>;
+        vddmipi-supply = <&v1_2d>;
+        vddio-supply = <&v3_3d>;
+
+        dsi_bridge_ports: ports {
+          #address-cells = <1>;
+          #size-cells = <0>;
+
+          port@0 {
+            reg = <0>;
+            rgb_in: endpoint {
+              remote-endpoint = <&dpi_out>;
+              data-lines = <24>;
+            };
+          };
+
+          port@1 {
+            reg = <1>;
+            dsi_out: endpoint {
+              remote-endpoint = <&lcd_in>;
+            };
+          };
+        };
+      };
+    };
diff --git a/Bindings/display/bridge/toshiba,tc358775.yaml b/Bindings/display/bridge/toshiba,tc358775.yaml
new file mode 100644
index 0000000..d879c70
--- /dev/null
+++ b/Bindings/display/bridge/toshiba,tc358775.yaml
@@ -0,0 +1,206 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/bridge/toshiba,tc358775.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba TC358775 DSI to LVDS bridge
+
+maintainers:
+  - Vinay Simha BN <simhavcs@gmail.com>
+
+description: |
+  This binding supports DSI to LVDS bridge TC358775
+
+  MIPI DSI-RX Data 4-lane, CLK 1-lane with data rates up to 800 Mbps/lane.
+  Video frame size:
+  Up to 1600x1200 24-bit/pixel resolution for single-link LVDS display panel
+  limited by 135 MHz LVDS speed
+  Up to WUXGA (1920x1200 24-bit pixels) resolution for dual-link LVDS display
+  panel, limited by 270 MHz LVDS speed.
+
+properties:
+  compatible:
+    const: toshiba,tc358775
+
+  reg:
+    maxItems: 1
+    description: i2c address of the bridge, 0x0f
+
+  vdd-supply:
+    description: 1.2V LVDS Power Supply
+
+  vddio-supply:
+    description: 1.8V IO Power Supply
+
+  stby-gpios:
+    maxItems: 1
+    description: Standby pin, Low active
+
+  reset-gpios:
+    maxItems: 1
+    description: Hardware reset, Low active
+
+  ports:
+    $ref: /schemas/graph.yaml#/properties/ports
+
+    properties:
+      port@0:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+          DSI Input. The remote endpoint phandle should be a
+          reference to a valid mipi_dsi_host device node.
+
+      port@1:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+          Video port for LVDS output (panel or connector).
+
+      port@2:
+        $ref: /schemas/graph.yaml#/properties/port
+        description: |
+          Video port for Dual link LVDS output (panel or connector).
+
+    required:
+      - port@0
+      - port@1
+
+required:
+  - compatible
+  - reg
+  - vdd-supply
+  - vddio-supply
+  - stby-gpios
+  - reset-gpios
+  - ports
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    /* For single-link LVDS display panel */
+
+    i2c@78b8000 {
+        /* On High speed expansion */
+        label = "HS-I2C2";
+        reg = <0x078b8000 0x500>;
+        clock-frequency = <400000>; /* fastmode operation */
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        tc_bridge: bridge@f {
+            compatible = "toshiba,tc358775";
+            reg = <0x0f>;
+
+            vdd-supply = <&pm8916_l2>;
+            vddio-supply = <&pm8916_l6>;
+
+            stby-gpios = <&msmgpio 99 GPIO_ACTIVE_LOW>;
+            reset-gpios = <&msmgpio 72 GPIO_ACTIVE_LOW>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    d2l_in_test: endpoint {
+                        remote-endpoint = <&dsi0_out>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    lvds_out: endpoint {
+                        remote-endpoint = <&panel_in>;
+                    };
+                };
+            };
+        };
+    };
+
+    dsi@1a98000 {
+        reg = <0x1a98000 0x25c>;
+        reg-names = "dsi_ctrl";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            port@1 {
+                reg = <1>;
+                dsi0_out: endpoint {
+                    remote-endpoint = <&d2l_in_test>;
+                    data-lanes = <0 1 2 3>;
+                };
+             };
+         };
+     };
+
+  - |
+    /* For dual-link LVDS display panel */
+
+    i2c@78b8000 {
+        /* On High speed expansion */
+        label = "HS-I2C2";
+        reg = <0x078b8000 0x500>;
+        clock-frequency = <400000>; /* fastmode operation */
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        tc_bridge_dual: bridge@f {
+            compatible = "toshiba,tc358775";
+            reg = <0x0f>;
+
+            vdd-supply = <&pm8916_l2>;
+            vddio-supply = <&pm8916_l6>;
+
+            stby-gpios = <&msmgpio 99 GPIO_ACTIVE_LOW>;
+            reset-gpios = <&msmgpio 72 GPIO_ACTIVE_LOW>;
+
+            ports {
+                #address-cells = <1>;
+                #size-cells = <0>;
+
+                port@0 {
+                    reg = <0>;
+                    d2l_in_dual: endpoint {
+                        remote-endpoint = <&dsi0_out_dual>;
+                    };
+                };
+
+                port@1 {
+                    reg = <1>;
+                    lvds0_out: endpoint {
+                        remote-endpoint = <&panel_in0>;
+                    };
+                };
+
+                port@2 {
+                    reg = <2>;
+                    lvds1_out: endpoint {
+                        remote-endpoint = <&panel_in1>;
+                    };
+                };
+            };
+        };
+    };
+
+    dsi@1a98000 {
+        reg = <0x1a98000 0x25c>;
+        reg-names = "dsi_ctrl";
+
+        ports {
+            #address-cells = <1>;
+            #size-cells = <0>;
+            port@1 {
+                reg = <1>;
+                dsi0_out_dual: endpoint {
+                    remote-endpoint = <&d2l_in_dual>;
+                    data-lanes = <0 1 2 3>;
+                };
+             };
+         };
+     };
+...