am335x_evm: am33xx_spl_board_init function and scale core frequency
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on. In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed. In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.
Signed-off-by: Tom Rini <trini@ti.com>
diff --git a/arch/arm/cpu/armv7/am33xx/sys_info.c b/arch/arm/cpu/armv7/am33xx/sys_info.c
index 63afaaa..50eb598 100644
--- a/arch/arm/cpu/armv7/am33xx/sys_info.c
+++ b/arch/arm/cpu/armv7/am33xx/sys_info.c
@@ -17,6 +17,7 @@
#include <asm/arch/sys_proto.h>
#include <asm/arch/cpu.h>
#include <asm/arch/clock.h>
+#include <power/tps65910.h>
struct ctrl_stat *cstat = (struct ctrl_stat *)CTRL_BASE;
@@ -119,3 +120,59 @@
return 0;
}
#endif /* CONFIG_DISPLAY_CPUINFO */
+
+#ifdef CONFIG_AM33XX
+int am335x_get_efuse_mpu_max_freq(struct ctrl_dev *cdev)
+{
+ int sil_rev;
+
+ sil_rev = readl(&cdev->deviceid) >> 28;
+
+ if (sil_rev == 1)
+ /* PG 2.0, efuse may not be set. */
+ return MPUPLL_M_800;
+ else if (sil_rev >= 2) {
+ /* Check what the efuse says our max speed is. */
+ int efuse_arm_mpu_max_freq;
+ efuse_arm_mpu_max_freq = readl(&cdev->efuse_sma);
+ switch ((efuse_arm_mpu_max_freq & DEVICE_ID_MASK)) {
+ case AM335X_ZCZ_1000:
+ return MPUPLL_M_1000;
+ case AM335X_ZCZ_800:
+ return MPUPLL_M_800;
+ case AM335X_ZCZ_720:
+ return MPUPLL_M_720;
+ case AM335X_ZCZ_600:
+ case AM335X_ZCE_600:
+ return MPUPLL_M_600;
+ case AM335X_ZCZ_300:
+ case AM335X_ZCE_300:
+ return MPUPLL_M_300;
+ }
+ }
+
+ /* PG 1.0 or otherwise unknown, use the PG1.0 max */
+ return MPUPLL_M_720;
+}
+
+int am335x_get_tps65910_mpu_vdd(int sil_rev, int frequency)
+{
+ /* For PG2.1 and later, we have one set of values. */
+ if (sil_rev >= 2) {
+ switch (frequency) {
+ case MPUPLL_M_1000:
+ return TPS65910_OP_REG_SEL_1_3_2_5;
+ case MPUPLL_M_800:
+ return TPS65910_OP_REG_SEL_1_2_6;
+ case MPUPLL_M_720:
+ return TPS65910_OP_REG_SEL_1_2_0;
+ case MPUPLL_M_600:
+ case MPUPLL_M_300:
+ return TPS65910_OP_REG_SEL_1_1_3;
+ }
+ }
+
+ /* Default to PG1.0/PG2.0 values. */
+ return TPS65910_OP_REG_SEL_1_1_3;
+}
+#endif
diff --git a/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h b/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h
index 140379f..aad698d 100644
--- a/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h
+++ b/arch/arm/include/asm/arch-am33xx/clocks_am33xx.h
@@ -11,9 +11,17 @@
#ifndef _CLOCKS_AM33XX_H_
#define _CLOCKS_AM33XX_H_
+/* MAIN PLL Fdll supported frequencies */
+#define MPUPLL_M_1000 1000
+#define MPUPLL_M_800 800
+#define MPUPLL_M_720 720
+#define MPUPLL_M_600 600
+#define MPUPLL_M_550 550
+#define MPUPLL_M_300 300
+
/* MAIN PLL Fdll = 550 MHz, by default */
#ifndef CONFIG_SYS_MPUCLK
-#define CONFIG_SYS_MPUCLK 550
+#define CONFIG_SYS_MPUCLK MPUPLL_M_550
#endif
#define UART_RESET (0x1 << 1)
diff --git a/arch/arm/include/asm/arch-am33xx/sys_proto.h b/arch/arm/include/asm/arch-am33xx/sys_proto.h
index 55f57ac..87b7d36 100644
--- a/arch/arm/include/asm/arch-am33xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-am33xx/sys_proto.h
@@ -10,6 +10,7 @@
#ifndef _SYS_PROTO_H_
#define _SYS_PROTO_H_
+#include <asm/arch/cpu.h>
#define BOARD_REV_ID 0x0
@@ -43,4 +44,6 @@
void enable_norboot_pin_mux(void);
#endif
void am33xx_spl_board_init(void);
+int am335x_get_efuse_mpu_max_freq(struct ctrl_dev *cdev);
+int am335x_get_tps65910_mpu_vdd(int sil_rev, int frequency);
#endif