| CONFIG_ARM=y |
| CONFIG_SKIP_LOWLEVEL_INIT_ONLY=y |
| CONFIG_SPL_SKIP_LOWLEVEL_INIT_ONLY=y |
| CONFIG_SYS_THUMB_BUILD=y |
| # CONFIG_SPL_USE_ARCH_MEMCPY is not set |
| # CONFIG_SPL_USE_ARCH_MEMSET is not set |
| CONFIG_ARCH_AT91=y |
| CONFIG_TEXT_BASE=0x72000000 |
| CONFIG_SYS_MALLOC_LEN=0x460000 |
| CONFIG_SYS_MALLOC_F_LEN=0x800 |
| CONFIG_TARGET_CORVUS=y |
| CONFIG_AT91_GPIO_PULLUP=y |
| CONFIG_ATMEL_LEGACY=y |
| CONFIG_SPL_GPIO=y |
| CONFIG_SPL_LIBCOMMON_SUPPORT=y |
| CONFIG_SPL_LIBGENERIC_SUPPORT=y |
| CONFIG_NR_DRAM_BANKS=1 |
| CONFIG_ENV_OFFSET=0x100000 |
| CONFIG_DEFAULT_DEVICE_TREE="at91sam9g45-corvus" |
| CONFIG_SPL_TEXT_BASE=0x300000 |
| CONFIG_SYS_PROMPT="U-Boot> " |
| CONFIG_SPL_SERIAL=y |
| CONFIG_SPL=y |
| CONFIG_ENV_OFFSET_REDUND=0x180000 |
| CONFIG_SYS_LOAD_ADDR=0x70000000 |
| CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y |
| CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x70007f00 |
| CONFIG_NAND_BOOT=y |
| CONFIG_BOOTDELAY=3 |
| CONFIG_USE_BOOTARGS=y |
| CONFIG_BOOTARGS="console=ttyS0,115200 earlyprintk mtdparts=atmel_nand:256k(bootstrap)ro,512k(uboot)ro,256k(env),256k(env_redundant),256k(spare),512k(dtb),6M(kernel)ro,-(rootfs) root=/dev/mtdblock7 rw rootfstype=jffs2" |
| CONFIG_USE_BOOTCOMMAND=y |
| CONFIG_BOOTCOMMAND="nand read 0x70000000 0x200000 0x300000;bootm 0x70000000" |
| # CONFIG_DISPLAY_BOARDINFO is not set |
| CONFIG_BOARD_EARLY_INIT_F=y |
| CONFIG_SPL_MAX_SIZE=0x3000 |
| CONFIG_SPL_PAD_TO=0x20000 |
| CONFIG_SPL_HAS_BSS_LINKER_SECTION=y |
| CONFIG_SPL_BSS_START_ADDR=0x3000 |
| CONFIG_SPL_BSS_MAX_SIZE=0x800 |
| CONFIG_SPL_SYS_MALLOC_SIMPLE=y |
| # CONFIG_SPL_SHARES_INIT_SP_ADDR is not set |
| CONFIG_SPL_STACK=0x4000 |
| CONFIG_SPL_NAND_SUPPORT=y |
| CONFIG_SPL_NAND_RAW_ONLY=y |
| CONFIG_SPL_NAND_DRIVERS=y |
| CONFIG_SPL_NAND_ECC=y |
| CONFIG_SPL_NAND_SOFTECC=y |
| CONFIG_SPL_NAND_BASE=y |
| CONFIG_HUSH_PARSER=y |
| CONFIG_SYS_CBSIZE=256 |
| CONFIG_SYS_PBSIZE=281 |
| # CONFIG_CMD_BDI is not set |
| CONFIG_CMD_BOOTZ=y |
| # CONFIG_CMD_IMI is not set |
| CONFIG_CMD_DFU=y |
| CONFIG_CMD_GPIO=y |
| # CONFIG_CMD_LOADS is not set |
| CONFIG_CMD_NAND=y |
| CONFIG_CMD_USB=y |
| # CONFIG_CMD_SOURCE is not set |
| # CONFIG_CMD_SETEXPR is not set |
| CONFIG_CMD_DHCP=y |
| CONFIG_BOOTP_BOOTFILESIZE=y |
| CONFIG_CMD_PING=y |
| CONFIG_CMD_MTDPARTS=y |
| CONFIG_DOS_PARTITION=y |
| CONFIG_OF_CONTROL=y |
| CONFIG_ENV_IS_IN_NAND=y |
| CONFIG_SYS_REDUNDAND_ENVIRONMENT=y |
| CONFIG_SYS_RELOC_GD_ENV_ADDR=y |
| CONFIG_NET_RETRY_COUNT=20 |
| CONFIG_CLK=y |
| CONFIG_CLK_AT91=y |
| CONFIG_DFU_NAND=y |
| CONFIG_SYS_DFU_DATA_BUF_SIZE=0x100000 |
| CONFIG_AT91_GPIO=y |
| # CONFIG_MMC is not set |
| CONFIG_MTD=y |
| CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT=y |
| # CONFIG_SYS_NAND_USE_FLASH_BBT is not set |
| CONFIG_NAND_ATMEL=y |
| CONFIG_SYS_NAND_BLOCK_SIZE=0x20000 |
| CONFIG_SYS_NAND_PAGE_COUNT=0x40 |
| CONFIG_SYS_NAND_PAGE_SIZE=0x800 |
| CONFIG_SYS_NAND_OOBSIZE=0x40 |
| CONFIG_SYS_NAND_U_BOOT_LOCATIONS=y |
| CONFIG_SYS_NAND_U_BOOT_OFFS=0x20000 |
| CONFIG_MACB=y |
| CONFIG_RMII=y |
| CONFIG_ATMEL_USART=y |
| CONFIG_USB=y |
| CONFIG_USB_EHCI_HCD=y |
| CONFIG_USB_GADGET=y |
| CONFIG_USB_GADGET_MANUFACTURER="Siemens AG" |
| CONFIG_USB_GADGET_VENDOR_NUM=0x0908 |
| CONFIG_USB_GADGET_PRODUCT_NUM=0x02d2 |
| CONFIG_USB_GADGET_ATMEL_USBA=y |
| CONFIG_USB_GADGET_DOWNLOAD=y |