[Blackfin][PATCH] Add BF561 EZKIT board support
diff --git a/cpu/bf561/init_sdram.S b/cpu/bf561/init_sdram.S
new file mode 100644
index 0000000..d763f27
--- /dev/null
+++ b/cpu/bf561/init_sdram.S
@@ -0,0 +1,171 @@
+#define ASSEMBLY
+
+#include <linux/config.h>
+#include <config.h>
+#include <asm/blackfin.h>
+#include <asm/mem_init.h>
+.global init_sdram;
+
+#if (CONFIG_CCLK_DIV == 1)
+#define CONFIG_CCLK_ACT_DIV CCLK_DIV1
+#endif
+#if (CONFIG_CCLK_DIV == 2)
+#define CONFIG_CCLK_ACT_DIV CCLK_DIV2
+#endif
+#if (CONFIG_CCLK_DIV == 4)
+#define CONFIG_CCLK_ACT_DIV CCLK_DIV4
+#endif
+#if (CONFIG_CCLK_DIV == 8)
+#define CONFIG_CCLK_ACT_DIV CCLK_DIV8
+#endif
+#ifndef CONFIG_CCLK_ACT_DIV
+#define CONFIG_CCLK_ACT_DIV CONFIG_CCLK_DIV_not_defined_properly
+#endif
+
+init_sdram:
+ [--SP] = ASTAT;
+ [--SP] = RETS;
+ [--SP] = (R7:0);
+ [--SP] = (P5:0);
+
+ /*
+ * PLL_LOCKCNT - how many SCLK Cycles to delay while PLL becomes stable
+ */
+ p0.h = hi(PLL_LOCKCNT);
+ p0.l = lo(PLL_LOCKCNT);
+ r0 = 0x300(Z);
+ w[p0] = r0.l;
+ ssync;
+
+ /*
+ * Put SDRAM in self-refresh, incase anything is running
+ */
+ P2.H = hi(EBIU_SDGCTL);
+ P2.L = lo(EBIU_SDGCTL);
+ R0 = [P2];
+ BITSET (R0, 24);
+ [P2] = R0;
+ SSYNC;
+
+ /*
+ * Set PLL_CTL with the value that we calculate in R0
+ * - [14:09] = MSEL[5:0] : CLKIN / VCO multiplication factors
+ * - [8] = BYPASS : BYPASS the PLL, run CLKIN into CCLK/SCLK
+ * - [7] = output delay (add 200ps of delay to mem signals)
+ * - [6] = input delay (add 200ps of input delay to mem signals)
+ * - [5] = PDWN : 1=All Clocks off
+ * - [3] = STOPCK : 1=Core Clock off
+ * - [1] = PLL_OFF : 1=Disable Power to PLL
+ * - [0] = DF : 1=Pass CLKIN/2 to PLL / 0=Pass CLKIN to PLL
+ * all other bits set to zero
+ */
+
+ r0 = CONFIG_VCO_MULT & 63; /* Load the VCO multiplier */
+ r0 = r0 << 9; /* Shift it over, */
+ r1 = CONFIG_CLKIN_HALF; /* Do we need to divide CLKIN by 2? */
+ r0 = r1 | r0;
+ r1 = CONFIG_PLL_BYPASS; /* Bypass the PLL? */
+ r1 = r1 << 8; /* Shift it over */
+ r0 = r1 | r0; /* add them all together */
+
+ p0.h = hi(PLL_CTL);
+ p0.l = lo(PLL_CTL); /* Load the address */
+ cli r2; /* Disable interrupts */
+ ssync;
+ w[p0] = r0.l; /* Set the value */
+ idle; /* Wait for the PLL to stablize */
+ sti r2; /* Enable interrupts */
+
+check_again:
+ p0.h = hi(PLL_STAT);
+ p0.l = lo(PLL_STAT);
+ R0 = W[P0](Z);
+ CC = BITTST(R0,5);
+ if ! CC jump check_again;
+
+ /* Configure SCLK & CCLK Dividers */
+ r0 = (CONFIG_CCLK_ACT_DIV | CONFIG_SCLK_DIV);
+ p0.h = hi(PLL_DIV);
+ p0.l = lo(PLL_DIV);
+ w[p0] = r0.l;
+ ssync;
+
+ /*
+ * We now are running at speed, time to set the Async mem bank wait states
+ * This will speed up execution, since we are normally running from FLASH.
+ */
+
+ p2.h = (EBIU_AMBCTL1 >> 16);
+ p2.l = (EBIU_AMBCTL1 & 0xFFFF);
+ r0.h = (AMBCTL1VAL >> 16);
+ r0.l = (AMBCTL1VAL & 0xFFFF);
+ [p2] = r0;
+ ssync;
+
+ p2.h = (EBIU_AMBCTL0 >> 16);
+ p2.l = (EBIU_AMBCTL0 & 0xFFFF);
+ r0.h = (AMBCTL0VAL >> 16);
+ r0.l = (AMBCTL0VAL & 0xFFFF);
+ [p2] = r0;
+ ssync;
+
+ p2.h = (EBIU_AMGCTL >> 16);
+ p2.l = (EBIU_AMGCTL & 0xffff);
+ r0 = AMGCTLVAL;
+ w[p2] = r0;
+ ssync;
+
+ /*
+ * Now, Initialize the SDRAM,
+ * start with the SDRAM Refresh Rate Control Register
+ */
+ p0.l = lo(EBIU_SDRRC);
+ p0.h = hi(EBIU_SDRRC);
+ r0 = mem_SDRRC;
+ w[p0] = r0.l;
+ ssync;
+
+ /*
+ * SDRAM Memory Bank Control Register - bank specific parameters
+ */
+ p0.l = (EBIU_SDBCTL & 0xFFFF);
+ p0.h = (EBIU_SDBCTL >> 16);
+ r0 = mem_SDBCTL;
+ w[p0] = r0.l;
+ ssync;
+
+ /*
+ * SDRAM Global Control Register - global programmable parameters
+ * Disable self-refresh
+ */
+ P2.H = hi(EBIU_SDGCTL);
+ P2.L = lo(EBIU_SDGCTL);
+ R0 = [P2];
+ BITCLR (R0, 24);
+
+ /*
+ * Check if SDRAM is already powered up, if it is, enable self-refresh
+ */
+ p0.h = hi(EBIU_SDSTAT);
+ p0.l = lo(EBIU_SDSTAT);
+ r2.l = w[p0];
+ cc = bittst(r2,3);
+ if !cc jump skip;
+ NOP;
+ BITSET (R0, 23);
+skip:
+ [P2] = R0;
+ SSYNC;
+
+ /* Write in the new value in the register */
+ R0.L = lo(mem_SDGCTL);
+ R0.H = hi(mem_SDGCTL);
+ [P2] = R0;
+ SSYNC;
+ nop;
+
+ (P5:0) = [SP++];
+ (R7:0) = [SP++];
+ RETS = [SP++];
+ ASTAT = [SP++];
+ RTS;