mvebu: pcie: Add support for GPIO reset for PCIe device
Add support for "marvell,reset-gpio" property to mvebu DW PCIe
driver.
This option is valid when CONFIG_DM_GPIO=y
Change-Id: Ic17c500449050c2fbb700731f1a9ca8b83298986
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/doc/device-tree-bindings/pci/armada8k-pcie.txt b/doc/device-tree-bindings/pci/armada8k-pcie.txt
new file mode 100644
index 0000000..7230f10
--- /dev/null
+++ b/doc/device-tree-bindings/pci/armada8k-pcie.txt
@@ -0,0 +1,49 @@
+Armada-8K PCIe DT details:
+==========================
+
+Armada-8k uses synopsis designware PCIe controller.
+
+Required properties:
+- compatible : should be "marvell,armada8k-pcie", "snps,dw-pcie".
+- reg: base addresses and lengths of the pcie control and global control registers.
+ "ctrl" registers points to the global control registers, while the "config" space
+ points to the pcie configuration registers as mentioned in dw-pcie dt bindings in the link below.
+- interrupt-map-mask and interrupt-map, standard PCI properties to
+ define the mapping of the PCIe interface to interrupt numbers.
+- All other definitions as per generic PCI bindings
+See Linux kernel documentation:
+"Documentation/devicetree/bindings/pci/designware-pcie.txt"
+
+Optional properties:
+PHY support is still not supported for armada-8k, once it will, the following parameters can be used:
+- phys : phandle to phy node associated with pcie controller.
+- phy-names : must be "pcie-phy"
+- marvell,reset-gpio : specifies a gpio that needs to be activated for plug-in
+ card reset signal release.
+Example:
+
+cpm_pcie0: pcie@f2600000 {
+ compatible = "marvell,armada8k-pcie", "snps,dw-pcie";
+ reg = <0 0xf2600000 0 0x10000>,
+ <0 0xf6f00000 0 0x80000>;
+ reg-names = "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ device_type = "pci";
+ dma-coherent;
+
+ bus-range = <0 0xff>;
+ ranges =
+ /* downstream I/O */
+ <0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000
+ /* non-prefetchable memory */
+ 0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ num-lanes = <1>;
+ clocks = <&cpm_syscon0 1 13>;
+ marvell,reset-gpio = <&cpm_gpio1 20 GPIO_ACTIVE_HIGH>;
+ status = "disabled";
+};