* Patches by David Müller, 14 Nov 2003:
- board/mpl/common/common_util.c
* implement support for BZIP2 compressed images
* various cleanups (printf -> puts, ...)
- board/mpl/common/flash.c
* report correct errors to upper layers
* check the erase fail and VPP low bits in status reg
- board/mpl/vcma9/cmd_vcma9.c
- board/mpl/vcma9/flash.c
* various cleanups (printf -> puts, ...)
- common/cmd_usb.c
* fix typo in comment
- cpu/arm920t/usb_ohci.c
* support for S3C2410 is missing in #if line
- drivers/cs8900.c
* reinit some registers in case of error (cable missing, ...)
- fs/fat/fat.c
* support for USB/MMC devices is missing in #if line
- include/configs/MIP405.h
- include/configs/PIP405.h
* enable BZIP2 support
* enlarge malloc space to 1MiB because of BZIP2 support
- include/configs/VCMA9.h
* enable BZIP2 support
* enlarge malloc space to 1MiB because of BZIP2 support
* enable USB support
- lib_arm/armlinux.c
* change calling convention of ARM Linux kernel as
described on http://www.arm.linux.org.uk/developer/booting.php
* Patch by Thomas Lange, 14 Nov 2003:
Split dbau1x00 into dbau1000, dbau1100 and dbau1500 configs to
support all these AMD boards.
* Patch by Thomas Lange, 14 Nov 2003:
Workaround for mips au1x00 physical memory accesses (the au1x00
uses a 36 bit bus internally and cannot access physical memory
directly. Use the uncached SDRAM address instead of the physical
one.)
diff --git a/cpu/arm920t/usb_ohci.c b/cpu/arm920t/usb_ohci.c
index a040c13..6f4a9f7 100644
--- a/cpu/arm920t/usb_ohci.c
+++ b/cpu/arm920t/usb_ohci.c
@@ -34,11 +34,16 @@
*/
#include <common.h>
-/* #include <pci.h> no PCI on the S3C2400 */
+/* #include <pci.h> no PCI on the S3C24X0 */
#ifdef CONFIG_USB_OHCI
+#if defined(CONFIG_S3C2400)
#include <s3c2400.h>
+#elif defined(CONFIG_S3C2410)
+#include <s3c2410.h>
+#endif
+
#include <malloc.h>
#include <usb.h>
#include "usb_ohci.h"
diff --git a/cpu/mips/au1x00_eth.c b/cpu/mips/au1x00_eth.c
index c23712b..ae51b75 100644
--- a/cpu/mips/au1x00_eth.c
+++ b/cpu/mips/au1x00_eth.c
@@ -31,12 +31,24 @@
/* We all use switches, right? ;-) */
#endif
+/* I assume ethernet behaves like au1000 */
+
#ifdef CONFIG_AU1000
/* Base address differ between cpu:s */
#define ETH0_BASE AU1000_ETH0_BASE
#define MAC0_ENABLE AU1000_MAC0_ENABLE
#else
+#ifdef CONFIG_AU1100
+#define ETH0_BASE AU1100_ETH0_BASE
+#define MAC0_ENABLE AU1100_MAC0_ENABLE
+#else
-#error "Au1100 and Au1500 not supported"
+#ifdef CONFIG_AU1500
+#define ETH0_BASE AU1500_ETH0_BASE
+#define MAC0_ENABLE AU1500_MAC0_ENABLE
+#else
+#error "No valid cpu set"
+#endif
+#endif
#endif
#include <common.h>
@@ -175,6 +187,7 @@
}
/* Put mac addr in little endian */
+ /* FIXME Check this for little endian mode */
#define ea eth_get_dev()->enetaddr
*mac_addr_high = (ea[5] << 8) | (ea[4] ) ;
*mac_addr_low = (ea[3] << 24) | (ea[2] << 16) |