armv8: ls1028a: Add NXP LS1028A SoC support
Ls1028a SoC is based on Layerscape Chassis Generation 3.2
architecture with features:
2 ARM v8 Cortex-A72 cores, CCI400, SEC, DDR3L/4, LCD, GPU, TSN
ENETC, 2 USB 3.0, 2 eSDHC, 2 FlexCAN, 2 SPI, SATA, 8 I2C controllers,
6 LPUARTs, GPIO, SAI, qDMA, eDMA, GIC, TMU etc.
Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
index d37e367..a843c1e 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Kconfig
@@ -20,6 +20,40 @@
select SYS_I2C_MXC_I2C2
imply PANIC_HANG
+config ARCH_LS1028A
+ bool
+ select ARMV8_SET_SMPEN
+ select FSL_LSCH3
+ select NXP_LSCH3_2
+ select SYS_FSL_HAS_CCI400
+ select SYS_FSL_SRDS_1
+ select SYS_HAS_SERDES
+ select SYS_FSL_DDR
+ select SYS_FSL_DDR_LE
+ select SYS_FSL_DDR_VER_50
+ select SYS_FSL_HAS_DDR3
+ select SYS_FSL_HAS_DDR4
+ select SYS_FSL_HAS_SEC
+ select SYS_FSL_SEC_COMPAT_5
+ select SYS_FSL_SEC_LE
+ select FSL_TZASC_1
+ select ARCH_EARLY_INIT_R
+ select BOARD_EARLY_INIT_F
+ select SYS_I2C_MXC
+ select SYS_I2C_MXC_I2C1
+ select SYS_I2C_MXC_I2C2
+ select SYS_I2C_MXC_I2C3
+ select SYS_I2C_MXC_I2C4
+ select SYS_I2C_MXC_I2C5
+ select SYS_I2C_MXC_I2C6
+ select SYS_I2C_MXC_I2C7
+ select SYS_I2C_MXC_I2C8
+ select SYS_FSL_ERRATUM_A009007
+ select SYS_FSL_ERRATUM_A008514 if !TFABOOT
+ select SYS_FSL_ERRATUM_A009663 if !TFABOOT
+ select SYS_FSL_ERRATUM_A009942 if !TFABOOT
+ imply PANIC_HANG
+
config ARCH_LS1043A
bool
select ARMV8_SET_SMPEN
@@ -244,6 +278,7 @@
string "PCIe compatible of Kernel DT"
depends on PCIE_LAYERSCAPE || PCIE_LAYERSCAPE_GEN4
default "fsl,ls1012a-pcie" if ARCH_LS1012A
+ default "fsl,ls1028a-pcie" if ARCH_LS1028A
default "fsl,ls1043a-pcie" if ARCH_LS1043A
default "fsl,ls1046a-pcie" if ARCH_LS1046A
default "fsl,ls2080a-pcie" if ARCH_LS2080A
@@ -343,6 +378,7 @@
config MAX_CPUS
int "Maximum number of CPUs permitted for Layerscape"
+ default 2 if ARCH_LS1028A
default 4 if ARCH_LS1043A
default 4 if ARCH_LS1046A
default 16 if ARCH_LS2080A
@@ -377,7 +413,7 @@
config SYS_CCI400_OFFSET
hex "Offset for CCI400 base"
depends on SYS_FSL_HAS_CCI400
- default 0x3090000 if ARCH_LS1088A
+ default 0x3090000 if ARCH_LS1088A || ARCH_LS1028A
default 0x180000 if FSL_LSCH2
help
Offset for CCI400 base
@@ -446,6 +482,7 @@
config SYS_FSL_PCLK_DIV
int "Platform clock divider"
+ default 1 if ARCH_LS1028A
default 1 if ARCH_LS1043A
default 1 if ARCH_LS1046A
default 1 if ARCH_LS1088A
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/Makefile b/arch/arm/cpu/armv8/fsl-layerscape/Makefile
index e9bc987..a8d3cf9 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/Makefile
+++ b/arch/arm/cpu/armv8/fsl-layerscape/Makefile
@@ -48,3 +48,7 @@
ifneq ($(CONFIG_ARCH_LS1088A),)
obj-$(CONFIG_SYS_HAS_SERDES) += ls1088a_serdes.o
endif
+
+ifneq ($(CONFIG_ARCH_LS1028A),)
+obj-$(CONFIG_SYS_HAS_SERDES) += ls1028a_serdes.o
+endif
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
index 9801e64..bbe3c88 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
+++ b/arch/arm/cpu/armv8/fsl-layerscape/cpu.c
@@ -58,6 +58,7 @@
CPU_TYPE_ENTRY(LS1026A, LS1026A, 2),
CPU_TYPE_ENTRY(LS2040A, LS2040A, 4),
CPU_TYPE_ENTRY(LS1012A, LS1012A, 1),
+ CPU_TYPE_ENTRY(LS1028A, LS1028A, 2),
CPU_TYPE_ENTRY(LS1088A, LS1088A, 8),
CPU_TYPE_ENTRY(LS1084A, LS1084A, 8),
CPU_TYPE_ENTRY(LS1048A, LS1048A, 4),
@@ -246,11 +247,13 @@
PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN
},
+#ifdef CONFIG_SYS_PCIE3_PHYS_ADDR
{ CONFIG_SYS_PCIE3_PHYS_ADDR, CONFIG_SYS_PCIE3_PHYS_ADDR,
CONFIG_SYS_PCIE3_PHYS_SIZE,
PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN
},
+#endif
#ifdef CONFIG_SYS_PCIE4_PHYS_ADDR
{ CONFIG_SYS_PCIE4_PHYS_ADDR, CONFIG_SYS_PCIE4_PHYS_ADDR,
CONFIG_SYS_PCIE4_PHYS_SIZE,
@@ -355,11 +358,13 @@
PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN
},
+#ifdef CONFIG_SYS_PCIE3_PHYS_ADDR
{ CONFIG_SYS_PCIE3_PHYS_ADDR, CONFIG_SYS_PCIE3_PHYS_ADDR,
CONFIG_SYS_PCIE3_PHYS_SIZE,
PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
PTE_BLOCK_NON_SHARE | PTE_BLOCK_PXN | PTE_BLOCK_UXN
},
+#endif
{ CONFIG_SYS_FSL_DRAM_BASE3, CONFIG_SYS_FSL_DRAM_BASE3,
CONFIG_SYS_FSL_DRAM_SIZE3,
PTE_BLOCK_MEMTYPE(MT_NORMAL) |
@@ -462,11 +467,13 @@
final_map[i].virt = 0x2800000000ULL;
final_map[i].size = 0x800000000ULL;
break;
+#ifdef CONFIG_SYS_PCIE3_PHYS_ADDR
case CONFIG_SYS_PCIE3_PHYS_ADDR:
final_map[i].phys = 0x3000000000ULL;
final_map[i].virt = 0x3000000000ULL;
final_map[i].size = 0x800000000ULL;
break;
+#endif
#ifdef CONFIG_SYS_PCIE4_PHYS_ADDR
case CONFIG_SYS_PCIE4_PHYS_ADDR:
final_map[i].phys = 0x3800000000ULL;
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
index a0e2621..ad55573 100644
--- a/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
+++ b/arch/arm/cpu/armv8/fsl-layerscape/doc/README.soc
@@ -8,6 +8,7 @@
6. LS2088A
7. LS2081A
8. LX2160A
+ 9. LS1028A
LS1043A
---------
@@ -328,3 +329,53 @@
2)LX2080A, few difference w.r.t. LX2160A:
a) Eight 64-bit ARM v8 Cortex-A72 CPUs
+
+
+LS1028A
+--------
+The QorIQ LS1028A processor integrates two 64-bit Arm Cortex-A72 cores with
+a GPU and LCD controller, as well as two TSN-enabled Ethernet controllers and
+a TSNenabled 4-port switch.
+
+The high performance Cortex-A72 cores, performing above 16,000 CoreMarks,
+combined with 2.5 Gbit Ethernet, PCI express Gen 3.0, SATA 3.0, USB 3.0 and
+Octal/Quad SPI interfaces provide capabilities for a number of industrial and
+embedded applications. The device provides excellent integration with the
+new Time-Sensitive Networking standard, and enables a number of
+TSN applications.
+
+The LS1028A SoC includes the following function and features:
+ - Two 64-bit ARM v8 A72 CPUs
+ - Cache Coherent interconnect (CCI-400)
+ - One 32-bit DDR3L/DDR4 SDRAM memory controller with ECC
+ - eDP/Displayport interface
+ - Graphics processing unit
+ - One Configurable x4 SerDes
+ - Ethernet interfaces
+ - Non-switched: One Ethernet MAC supporting 2.5G, 1G, 100M, 10M, one
+ ethernet MAC supporting 1G, 100M, 10M.
+ - Switched: TSN IP to support four 2.5/1G interfaces.
+ - None of the MACs support MACSEC
+ - Support for RGMII, SGMII (and 1000Base-KX), SGMII 2.5x, QSGMII
+ - Support for 10G-SXGMII and 10G-QXGMII.
+ - Energy efficient Ethernet support (802.3az)
+ - IEEE 1588 support
+ - High-speed peripheral interfaces
+ - Two PCIe 3.0 controllers, one supporting x4 operation
+ - One serial ATA (SATA 3.0) controller
+ - Additional peripheral interfaces
+ - Two high-speed USB 2.0/3.0 controllers with integrated PHY each
+ supporting host or device modes
+ - Two Enhanced secure digital host controllers (SD/SDIO/eMMC)
+ - Two Serial peripheral interface (SPI) controllers
+ - Eight I2C controllers
+ - Two UART controllers
+ - Additional six Industrual UARTs (LPUART).
+ - One FlexSPI controller
+ - General Purpose IO (GPIO)
+ - Two CAN-FD interfaces
+ - Eight Flextimers with PWM I/O
+ - Support for hardware virtualization and partitioning enforcement
+ - Layerscape Trust Architecture
+ - Service Processor (SP) provides pre-boot initialization and secure-boot
+ capabilities
diff --git a/arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c b/arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c
new file mode 100644
index 0000000..ef598c4
--- /dev/null
+++ b/arch/arm/cpu/armv8/fsl-layerscape/ls1028a_serdes.c
@@ -0,0 +1,73 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019 NXP
+ */
+
+#include <common.h>
+#include <asm/arch/fsl_serdes.h>
+
+struct serdes_config {
+ u32 protocol;
+ u8 lanes[SRDS_MAX_LANES];
+ u8 rcw_lanes[SRDS_MAX_LANES];
+};
+
+static struct serdes_config serdes1_cfg_tbl[] = {
+ /* SerDes 1 */
+ {0xCC5B, {PCIE1, QSGMII_B, PCIE2, PCIE2} },
+ {0xEB99, {SGMII1, SGMII1, PCIE2, SATA1} },
+ {0xCC99, {SGMII1, SGMII1, PCIE2, PCIE2} },
+ {0xBB99, {SGMII1, SGMII1, PCIE2, PCIE1} },
+ {0x9999, {SGMII1, SGMII2, SGMII3, SGMII4} },
+ {0xEBCC, {PCIE1, PCIE1, PCIE2, SATA1} },
+ {0xCCCC, {PCIE1, PCIE1, PCIE2, PCIE2} },
+ {0xDDDD, {PCIE1, PCIE1, PCIE1, PCIE1} },
+ {}
+};
+
+static struct serdes_config *serdes_cfg_tbl[] = {
+ serdes1_cfg_tbl,
+};
+
+enum srds_prtcl serdes_get_prtcl(int serdes, int cfg, int lane)
+{
+ struct serdes_config *ptr;
+
+ if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ ptr = serdes_cfg_tbl[serdes];
+ while (ptr->protocol) {
+ if (ptr->protocol == cfg)
+ return ptr->lanes[lane];
+ ptr++;
+ }
+
+ return 0;
+}
+
+int is_serdes_prtcl_valid(int serdes, u32 prtcl)
+{
+ int i;
+ struct serdes_config *ptr;
+
+ if (serdes >= ARRAY_SIZE(serdes_cfg_tbl))
+ return 0;
+
+ ptr = serdes_cfg_tbl[serdes];
+ while (ptr->protocol) {
+ if (ptr->protocol == prtcl)
+ break;
+ ptr++;
+ }
+
+ if (!ptr->protocol)
+ return 0;
+
+ for (i = 0; i < SRDS_MAX_LANES; i++) {
+ if (ptr->lanes[i] != NONE)
+ return 1;
+ }
+
+ return 0;
+}
diff --git a/arch/arm/dts/fsl-ls1028a.dtsi b/arch/arm/dts/fsl-ls1028a.dtsi
new file mode 100644
index 0000000..1274d2c
--- /dev/null
+++ b/arch/arm/dts/fsl-ls1028a.dtsi
@@ -0,0 +1,280 @@
+// SPDX-License-Identifier: GPL-2.0+ OR X11
+/*
+ * NXP ls1028a SOC common device tree source
+ *
+ * Copyright 2019 NXP
+ *
+ */
+
+/ {
+ compatible = "fsl,ls1028a";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ sysclk: sysclk {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <100000000>;
+ clock-output-names = "sysclk";
+ };
+
+ clockgen: clocking@1300000 {
+ compatible = "fsl,ls1028a-clockgen";
+ reg = <0x0 0x1300000 0x0 0xa0000>;
+ #clock-cells = <2>;
+ clocks = <&sysclk>;
+ };
+
+ memory@01080000 {
+ device_type = "memory";
+ reg = <0x00000000 0x01080000 0 0x80000000>;
+ /* DRAM space - 1, size : 2 GB DRAM */
+ };
+
+ gic: interrupt-controller@6000000 {
+ compatible = "arm,gic-v3";
+ reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+ <0x0 0x06040000 0 0x40000>;
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ interrupts = <1 9 0x4>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <1 13 0x8>, /* Physical Secure PPI, active-low */
+ <1 14 0x8>, /* Physical Non-Secure PPI, active-low */
+ <1 11 0x8>, /* Virtual PPI, active-low */
+ <1 10 0x8>; /* Hypervisor PPI, active-low */
+ };
+
+ fspi: flexspi@20C0000 {
+ compatible = "nxp,dn-fspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x20C0000 0x0 0x10000>,
+ <0x0 0x20000000 0x0 0x10000000>; /*64MB flash*/
+ reg-names = "FSPI", "FSPI-memory";
+ num-cs = <1>;
+ status = "disabled";
+ };
+
+ serial0: serial@21c0500 {
+ device_type = "serial";
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21c0500 0x0 0x100>;
+ interrupts = <0 32 0x1>; /* edge triggered */
+ status = "disabled";
+ };
+
+ serial1: serial@21c0600 {
+ device_type = "serial";
+ compatible = "fsl,ns16550", "ns16550a";
+ reg = <0x0 0x21c0600 0x0 0x100>;
+ interrupts = <0 32 0x1>; /* edge triggered */
+ status = "disabled";
+ };
+
+ pcie@3400000 {
+ compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie";
+ reg = <0x00 0x03400000 0x0 0x80000
+ 0x00 0x03480000 0x0 0x40000 /* lut registers */
+ 0x00 0x034c0000 0x0 0x40000 /* pf controls registers */
+ 0x80 0x00000000 0x0 0x20000>; /* configuration space */
+ reg-names = "dbi", "lut", "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x80 0x00020000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x80 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ };
+
+ pcie@3500000 {
+ compatible = "fsl,ls-pcie", "fsl,ls1028-pcie", "snps,dw-pcie";
+ reg = <0x00 0x03500000 0x0 0x80000
+ 0x00 0x03580000 0x0 0x40000 /* lut registers */
+ 0x00 0x035c0000 0x0 0x40000 /* pf controls registers */
+ 0x88 0x00000000 0x0 0x20000>; /* configuration space */
+ reg-names = "dbi", "lut", "ctrl", "config";
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ num-lanes = <4>;
+ bus-range = <0x0 0xff>;
+ ranges = <0x81000000 0x0 0x00000000 0x88 0x00020000 0x0 0x00010000 /* downstream I/O */
+ 0x82000000 0x0 0x40000000 0x88 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
+ };
+
+ i2c0: i2c@2000000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2000000 0x0 0x10000>;
+ interrupts = <0 34 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@2010000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2010000 0x0 0x10000>;
+ interrupts = <0 34 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@2020000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2020000 0x0 0x10000>;
+ interrupts = <0 35 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@2030000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2030000 0x0 0x10000>;
+ interrupts = <0 35 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@2040000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2040000 0x0 0x10000>;
+ interrupts = <0 74 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c5: i2c@2050000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2050000 0x0 0x10000>;
+ interrupts = <0 74 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c6: i2c@2060000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2060000 0x0 0x10000>;
+ interrupts = <0 75 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ i2c7: i2c@2070000 {
+ compatible = "fsl,vf610-i2c";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2070000 0x0 0x10000>;
+ interrupts = <0 75 0x4>;
+ clock-names = "i2c";
+ clocks = <&clockgen 4 0>;
+ status = "disabled";
+ };
+
+ usb1: usb3@3100000 {
+ compatible = "fsl,layerscape-dwc3";
+ reg = <0x0 0x3100000 0x0 0x10000>;
+ interrupts = <0 80 0x4>;
+ dr_mode = "host";
+ status = "disabled";
+ };
+
+ usb2: usb3@3110000 {
+ compatible = "fsl,layerscape-dwc3";
+ reg = <0x0 0x3110000 0x0 0x10000>;
+ interrupts = <0 81 0x4>;
+ dr_mode = "host";
+ status = "disabled";
+ };
+
+ dspi0: dspi@2100000 {
+ compatible = "fsl,vf610-dspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2100000 0x0 0x10000>;
+ interrupts = <0 26 0x4>;
+ clock-names = "dspi";
+ clocks = <&clockgen 4 0>;
+ num-cs = <5>;
+ litte-endian;
+ status = "disabled";
+ };
+
+ dspi1: dspi@2110000 {
+ compatible = "fsl,vf610-dspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2110000 0x0 0x10000>;
+ interrupts = <0 26 0x4>;
+ clock-names = "dspi";
+ clocks = <&clockgen 4 0>;
+ num-cs = <5>;
+ little-endian;
+ status = "disabled";
+ };
+
+ dspi2: dspi@2120000 {
+ compatible = "fsl,vf610-dspi";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x0 0x2120000 0x0 0x10000>;
+ interrupts = <0 26 0x4>;
+ clock-names = "dspi";
+ clocks = <&clockgen 4 0>;
+ num-cs = <5>;
+ little-endian;
+ status = "disabled";
+ };
+
+ esdhc0: esdhc@2140000 {
+ compatible = "fsl,esdhc";
+ reg = <0x0 0x2140000 0x0 0x10000>;
+ interrupts = <0 28 0x4>;
+ big-endian;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ esdhc1: esdhc@2150000 {
+ compatible = "fsl,esdhc";
+ reg = <0x0 0x2150000 0x0 0x10000>;
+ interrupts = <0 63 0x4>;
+ big-endian;
+ non-removable;
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ sata: sata@3200000 {
+ compatible = "fsl,ls1028a-ahci";
+ reg = <0x0 0x3200000 0x0 0x10000>;
+ interrupts = <0 133 4>;
+ clocks = <&clockgen 4 1>;
+ status = "disabled";
+ };
+};
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/config.h b/arch/arm/include/asm/arch-fsl-layerscape/config.h
index 903d509..eb21c09 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/config.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/config.h
@@ -229,6 +229,67 @@
#define CONFIG_SYS_FSL_MAX_NUM_OF_SEC 1
+#elif defined(CONFIG_ARCH_LS1028A)
+#define CONFIG_SYS_FSL_NUM_CC_PLLS 3
+#define CONFIG_SYS_FSL_CLUSTER_CLOCKS { 1, 1 }
+#define CONFIG_GICV3
+#define CONFIG_FSL_TZPC_BP147
+#define CONFIG_FSL_TZASC_400
+
+/* TZ Protection Controller Definitions */
+#define TZPC_BASE 0x02200000
+#define TZPCR0SIZE_BASE (TZPC_BASE)
+#define TZPCDECPROT_0_STAT_BASE (TZPC_BASE + 0x800)
+#define TZPCDECPROT_0_SET_BASE (TZPC_BASE + 0x804)
+#define TZPCDECPROT_0_CLR_BASE (TZPC_BASE + 0x808)
+#define TZPCDECPROT_1_STAT_BASE (TZPC_BASE + 0x80C)
+#define TZPCDECPROT_1_SET_BASE (TZPC_BASE + 0x810)
+#define TZPCDECPROT_1_CLR_BASE (TZPC_BASE + 0x814)
+#define TZPCDECPROT_2_STAT_BASE (TZPC_BASE + 0x818)
+#define TZPCDECPROT_2_SET_BASE (TZPC_BASE + 0x81C)
+#define TZPCDECPROT_2_CLR_BASE (TZPC_BASE + 0x820)
+
+#define SRDS_MAX_LANES 4
+
+#define CONFIG_SYS_FSL_OCRAM_BASE 0x18000000 /* initial RAM */
+#define SYS_FSL_OCRAM_SPACE_SIZE 0x00200000 /* 2M */
+#define CONFIG_SYS_FSL_OCRAM_SIZE 0x00040000 /* Real size 256K */
+
+/* Generic Interrupt Controller Definitions */
+#define GICD_BASE 0x06000000
+#define GICR_BASE 0x06040000
+
+/* SMMU Definitions */
+#define SMMU_BASE 0x05000000 /* GR0 Base */
+
+/* DDR */
+#define CONFIG_SYS_DDR_BLOCK1_SIZE ((phys_size_t)2 << 30)
+#define CONFIG_MAX_MEM_MAPPED CONFIG_SYS_DDR_BLOCK1_SIZE
+
+#define CONFIG_SYS_FSL_CCSR_GUR_LE
+#define CONFIG_SYS_FSL_CCSR_SCFG_LE
+#define CONFIG_SYS_FSL_ESDHC_LE
+#define CONFIG_SYS_FSL_PEX_LUT_LE
+
+#define CONFIG_SYS_MEMAC_LITTLE_ENDIAN
+
+/* SFP */
+#define CONFIG_SYS_FSL_SFP_VER_3_4
+#define CONFIG_SYS_FSL_SFP_LE
+#define CONFIG_SYS_FSL_SRK_LE
+
+/* SEC */
+#define CONFIG_SYS_FSL_MAX_NUM_OF_SEC 1
+
+/* Security Monitor */
+#define CONFIG_SYS_FSL_SEC_MON_LE
+
+/* Secure Boot */
+#define CONFIG_ESBC_HDR_LS
+
+/* DCFG - GUR */
+#define CONFIG_SYS_FSL_CCSR_GUR_LE
+
#elif defined(CONFIG_FSL_LSCH2)
#define CONFIG_SYS_FSL_OCRAM_BASE 0x10000000 /* initial RAM */
#define SYS_FSL_OCRAM_SPACE_SIZE 0x00200000 /* 2M space */
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
index c9aa0ca..24c1b0e 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
@@ -183,6 +183,9 @@
#define CONFIG_SYS_PCIE1_PHYS_ADDR 0x2000000000ULL
#define CONFIG_SYS_PCIE2_PHYS_ADDR 0x2800000000ULL
#define CONFIG_SYS_PCIE3_PHYS_ADDR 0x3000000000ULL
+#elif CONFIG_ARCH_LS1028A
+#define CONFIG_SYS_PCIE1_PHYS_ADDR 0x8000000000ULL
+#define CONFIG_SYS_PCIE2_PHYS_ADDR 0x8800000000ULL
#else
#define CONFIG_SYS_PCIE1_PHYS_ADDR 0x1000000000ULL
#define CONFIG_SYS_PCIE2_PHYS_ADDR 0x1200000000ULL
@@ -387,6 +390,12 @@
#define FSL_CHASSIS3_SRDS2_PRTCL_SHIFT FSL_CHASSIS3_RCWSR30_SRDS2_PRTCL_SHIFT
#define FSL_CHASSIS3_SRDS1_REGSR 29
#define FSL_CHASSIS3_SRDS2_REGSR 30
+#elif defined(CONFIG_ARCH_LS1028A)
+#define FSL_CHASSIS3_RCWSR29_SRDS1_PRTCL_MASK 0xFFFF0000
+#define FSL_CHASSIS3_RCWSR29_SRDS1_PRTCL_SHIFT 16
+#define FSL_CHASSIS3_SRDS1_PRTCL_MASK FSL_CHASSIS3_RCWSR29_SRDS1_PRTCL_MASK
+#define FSL_CHASSIS3_SRDS1_PRTCL_SHIFT FSL_CHASSIS3_RCWSR29_SRDS1_PRTCL_SHIFT
+#define FSL_CHASSIS3_SRDS1_REGSR 29
#endif
#define RCW_SB_EN_REG_INDEX 9
#define RCW_SB_EN_MASK 0x00000400
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/soc.h b/arch/arm/include/asm/arch-fsl-layerscape/soc.h
index 7d95c4e..234440b 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/soc.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/soc.h
@@ -83,6 +83,7 @@
/* LS1043A/LS1023A 23x23 package silicon has different value of VAR_PER */
#define SVR_LS1043A_P23 0x879202
#define SVR_LS1023A_P23 0x87920A
+#define SVR_LS1028A 0x870B00
#define SVR_LS1046A 0x870700
#define SVR_LS1026A 0x870708
#define SVR_LS1048A 0x870320
diff --git a/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h b/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h
index e017d8b..c53cc57 100644
--- a/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h
+++ b/arch/arm/include/asm/arch-fsl-layerscape/stream_id_lsch3.h
@@ -87,7 +87,7 @@
#define FSL_PEX_STREAM_ID_NUM (0x100)
#endif
-#if defined(CONFIG_ARCH_LS2080A)
+#if defined(CONFIG_ARCH_LS2080A) || defined(CONFIG_ARCH_LS1028A)
#define FSL_PEX_STREAM_ID_END 22
#elif defined(CONFIG_ARCH_LS1088A)
#define FSL_PEX_STREAM_ID_END 18